Palm oil is known to be rich in carotenoids and other phytonutrients. However, the carotenoids and phytonutrients degrade due to high heat sterilization of oil palm fruits. The present study was conducted to produce carotenoid-rich virgin palm oil (VPO) using cold-press extraction. Herein, the influence of sterilization of oil palm fresh fruits in the production of cold-pressed VPO was determined with varying sterilization temperatures, times, and amounts of palm fruits in sterilization. The experimental sterilization conditions were optimized using response surface methodology (RSM) based on the maximum VPO yield and minimum FFAs in cold-pressed VPO. The optimal sterilization experimental conditions of oil palm fruits were determined to be a sterilization temperature of 62 °C, a time of 90 min, and an amount of oil palm fruits of 8 kg. Under these experimental conditions, the maximum cold-pressed VPO yield and the minimal content of free fatty acids (FFAs) obtained were 27.94 wt.% and 1.32 wt.%, respectively. Several analytic methods were employed to determine cold-pressed VPO quality and fatty acids compositions and compared with the crude palm oil. It was found that cold-pressed VPO contains higher carotenoids (708 mg/g) and unsaturated fatty acids compared with the carotenoid (343 mg/g) and fatty acid compositions in CPO. The findings of the present study reveal that the sterilization temperature potentially influences the carotenoid and nutrient contents in VPO; therefore, the optimization of the sterilization conditions is crucial to producing carotenoid- and phytonutrient-rich VPO.
The utilisation of quinoa protein concentrates (QPCs) is limited due to their poor protein digestibility (78.54 %). In this study, QPCs (1 % w/v) were fermented in 5 % (v/v) water kefir grains (WKG) for 5 days at 25 °C. The protein quality of the fermented QPCs was enhanced, whereby the protein digestibility increased significantly (P
Composition, physicochemical properties and enzyme inactivation kinetics of coconut water were compared between immature (IMC), mature (MC) and overly-mature coconuts (OMC). Among the samples studied, pH, turbidity and mineral contents for OMC water was the highest, whereas water volume, titratable acidity, total soluble solids and total phenolics content for OMC water were the lowest. Maturity was found to affect sugar contents. Sucrose content was found to increase with maturity, and the reverse trend was observed for fructose and glucose. Enzyme activity assessment showed that polyphenol oxidase (PPO) in all samples was more heat resistant than peroxidase (POD). Compared to IMC and MC, PPO and POD from OMC water showed the lowest thermal resistance, with D83.3°C=243.9s (z=27.9°C), and D83.3°C=129.9s (z=19.5°C), respectively.
Present study compared the rheological properties of glutinous rice flour (GRF) gel (33.3%, w/v) added with raw bee honey (RBH) or stingless bee honey (SBH) with/without heating treatment. RBH (diatase activity: 12.14 Schade) and SBH (1.53 Schade) significantly reduced the network of GRF gel by lowering the gel viscosity, with RBH having the highest rate of viscosity decrease (- 2.74 × 10-5 Pa). As the addition of heated-SBH or heated-RBH did not reduce gel viscosity, it was hypothesised that active diastase played a major role to weaken gel network. This was further supported by the significant and the lowest storage modulus (G') value of RBH-GRF gel (5.99 ± 0.02 Pa), as compared to SBH-GRF (6.27 ± 0.04 Pa) and control (6.33 ± 0.04 Pa). A detail of rheological behaviour of the gels was further explained using power law. Overall, this GRF gel model has successfully demonstrated the potential of honey diastase in weakening network of starch-based food.
The application of protein-protein interaction (PPI) has been widely used in various industries, such as food, nutraceutical, and pharmaceutical. A deeper understanding of PPI is needed, and the molecular forces governing proteins and their interaction must be explained. The design of new structures with improved functional properties, e.g., solubility, emulsion, and gelation, has been fueled by the development of structural and colloidal building blocks. In this review, the molecular forces of protein structures are discussed, followed by the relationship between molecular force and structure, ways of a bind of proteins together in solution or at the interface, and functional properties. A more detailed look is thus taken at the relationship between the various influencing factors on molecular forces involved in PPI. These factors include protein properties, such as types, concentration, and mixing ratio, and solvent conditions, such as ionic strength and pH. This review also summarizes methods tha1t are capable of identifying molecular forces in protein and PPI, as well as characterizing protein structure.
Peanut (Arachis hypogaea) is an important source of protein and lipid globally. The effect of superheated-steam roasting on quality of peanut oil was evaluated based on physicochemical quality parameters. Three roasting temperatures (150, 200, and 250 °C) were used for different periods of roasting time and the obtained results were compared with those of conventional roasting. At 250 °C, superheated-steam roasted peanuts yielded more oil (26.84%) than conventionally roasted peanuts (24.85%). Compared with conventional roasting, superheated-steam roasting resulted in lower oil color, peroxide, p-anisidine, free fatty acid, conjugated diene and triene, and acid values and higher viscosity and iodine values in the roasted peanut oil. These values were significantly different from each other (p
Poor solubility is a substantial factor that restricts the production of high value-added lentil proteins (LPs). In this study, whey protein isolates (WPIs), which have high solubility and are used in various food industries, were mixed with LPs at pH 12 to create LP-WPI protein complexes with improved water solubility properties using pH-recycling approach (maintained at pH 12.0 for 60 min and then readjusting to pH 7.0). LP-WPI protein complexes produced in this study have gained high surface charge, increased in the solubilization of protein complexes to ≈92%, as well as improved resistance against protein aggregation. The ratio of LPs to WPIs has a significant effect on the generation of unique tertiary and secondary protein structures based on the protein-protein interaction (PPI) technique via pH-recycling. The protein interaction between LPs and WPIs resulted in alteration on the surface morphology of the produced protein complexes. This study showed that electrostatic interaction, hydrophobic force, and hydrogen bond appear as major molecular forces in this PPI. The efficacy of the pH-recycling method used in this research indicates that this approach could be a robust approach to enhance the functional properties of food proteins. PRACTICAL APPLICATION: The pH-recycling technique is a proven technique for protein complexation in creating novel protein complexes with improved functional properties. Even though lentils are a rich source of plant-based protein, its utilization by food industries is restricted due to the poor water solubility of lentil proteins (LPs). However, by using complexing lentil proteins with whey protein isolates (WPIs), that is, LP-WPI protein complex, was developed. The water solubility of LP-WPI protein complex was significantly higher than LPs, up to approximately 92%. In addition, this could improve the utilization of lentil seeds in food application as an alternative for animal-based proteins.
Demands for high nutritional value-added food products and plant-based proteins have increased over the last decade, in line with the growth of the human population and consumer health awareness. The quality of the plant-based proteins depends on their digestibility, amino acid content, and residues of non-nutritive compounds, such as phenolic compounds, anti-nutritional compounds, antioxidants, and saponins. The presence of these non-nutritive compounds could have detrimental effects on the quality of the proteins. One of the solutions to address these shortcomings of plant-based proteins is fermentation, whereby enzymes that present naturally in microorganisms used during fermentation are responsible for the cleavage of the bonds between proteins and non-nutritive compounds. This mechanism has pronounced effects on the non-nutritive compounds, resulting in the enhancement of protein digestibility and functional properties of plant-based proteins. We assert that the types of plant-based proteins and microorganisms used during fermentation must be carefully addressed to truly enhance the quality, functional properties, and health functionalities of plant-based proteins.Supplemental data for this article is available online at here. show.
In Malaysia, fresh ulam raja leaves (Cosmos caudatus) are eaten raw with rice. In this study, beef patties incorporated with extracts of ulam raja (UREX) and commercial green tea extract (GTE) added individually at 200 and 500 mg/kg were stored at -18°C for up to 10 weeks. Lipid oxidation, cooking yield, physicochemical properties, textural properties, proximate composition and sensory characteristics of the beef patties were compared between those incorporated with UREX, GTE and the control (pure beef patty). Incorporation of UREX or GTE at 500 mg/kg into beef patties reduced the extent of lipid oxidation significantly (P<0.05). UREX showed a strong lipid oxidation inhibitory effect, comparable with GTE. In addition, a significant improvement (P<0.05) in cooking yield and textural properties was also recorded. However, incorporation of UREX and GTE into beef patties showed no significant influence (P>0.05) on the colour, pH, proximate composition and overall sensory acceptability of the patties.
Physicochemical properties of threadfin bream surimi with different levels of polydextrose (3%, 6%, 9% and 12%), raw surimi, raw surimi with addition sodium tripolyphosphate and commercial surimi (sucrose) during 6 months of frozen storage were investigated. The analyses included the measurement of Ca(2+)-ATPase, sulfhydryl contents, protein solubility, sodium dodecyl sulfate polyacrylamide gel electrophoresis, differential scanning calorimetry and scanning electron microscopy. The Ca(2+)-ATPase, sulfhydryl content and protein solubility levels added with 3%, 6%, 9% and 12% polydextrose can be maintained until the 6 months of storage by 47.33%, 41.60% and 51.41%, respectively. Differential scanning calorimetry showed decreases in thermal stabilization of myosin with regard to transition termperature. Analysis by scanning electron microscopy demonstrated that the number of pores formed was increased after storage. This study suggested that surimi stored with the polydextrose as a cryoprotectant was able to maintain physicochemical of surimi better compared to raw surimi with no additives or raw surimi with sodium tripolyphosphate.
Yellow alkaline noodles (YAN) prepared by partial substitution of wheat flour with soy protein isolate and treated with microbial transglutaminase (MTG) and ribose were investigated during cooking. Cooking caused an increase in lightness but a decrease in redness and yellowness, pH, tensile strength and elasticity values of noodles. The extents of these changes were influenced by formulation and cross-linking treatments. The pH and lightness for YAN-ribose were lowest but the yellowness and redness were the highest whilst the tensile strength and elasticity values remained moderate. For YAN-MTG, the color and pH values were moderate, but tensile strength and elasticity values were the highest. YAN prepared with both cross-linking agents had physical values between YAN-ribose and YAN-MTG. Although certain sensory parameters showed differences in score, the overall acceptability of all 10-min-cooked YAN was similar. It is possible to employ cross-linking agents to improve physical properties of cooked YAN.
Probiotics are live micro-organisms that exert beneficial effects on their host. A high survival rate during gastrointestinal transit and storage is often desirable. The main aim of this study was to develop protective carriers for probiotics via the use of enzymatically crosslinked soy protein isolate incorporated with agrowastes such as banana peel, banana pulp, cempedak rind and cocoa rind.
Response surface methodology (RSM) was carried out to study the effect of temperature, pH, and heating time as input variables on the yield and degree of esterification (DE) as the output (responses). The results showed that yield and DE of extracted pectin ranged from 2.27% to 9.35% (w/w, based on dry weight of durian rind) and 47.66% to 68.6%, respectively. The results also showed that a 2nd-order model adequately fitted the experimental data for the yield and DE. Optimum condition for maximum yield and DE was achieved at 85 degrees C, a time of either 4 or 1 h, and a pH of 2 or 2.5.
D-optimal design was employed to optimize the mixture of cross-linking agents formulation: microbial transglutaminase (MTGase) and ribose, and the processing parameters (i.e. incubation and heating time) in the mixture in order to obtain combined-cross-linked bovine serum albumin gels that have high gel strength, pH close to neutral and yet medium in browning. Analysis of variance (ANOVA) showed that the contribution of quadratic term to the model over the linear was significant for pH and L* value, whereas linear model was significant for gel strength. Optimization study using response surface methodology (RSM) was performed to the mixture components and process variables and the optimum conditions obtained were: MTGase of 1.34-1.43 g/100 mL, ribose of 1.07-1.16 g/100 mL, incubation time of 5 h at 40 degrees C and heating time of 3 h at 90 degrees C.
Cross-linked soy protein isolate (SPI) gels were produced via single-treatment of SPI with microbial transglutaminase (MTG) for 5 h or 24 h, or with ribose for 2 h, or via combined-treatments of SPI with MTG followed by heating with ribose. Assessment of gel strength and solubility concluded that measures which increased protein cross-links resulted in improved gel strength; however, in most cases the digestibility and amino acid content of the gels were reduced. The combined treated gel of SPI/MTG for 24 h/ribose was more easily digested by digestive enzymes and retained higher amounts of amino acids compared with the control Maillard gels of SPI with ribose. MTG consumed lysine and glutamine and reduced the availability of amino acids for the Maillard reaction with ribose. MTG was able to preserve the nutritional value of SPI against the destructive effect of the Maillard reaction and cross-links.
Statistical analysis of heavy metal concentrations in sediment was studied to understand the interrelationship between different parameters and also to identify probable source component in order to explain the pollution status of selected estuaries. Concentrations of heavy metals (Cu, Zn, Cd, Fe, Pb, Cr, Hg and Mn) were analyzed in sediments from Juru and Jejawi Estuaries in Malaysia with ten sampling points of each estuary. The results of multivariate statistical techniques showed that the two regions have different characteristics in terms of heavy metals selected and indicates that each region receives pollution from different sources. The results also showed that Fe, Mn, Cd, Hg, and Cu are responsible for large spatial variations explaining 51.15% of the total variance, whilst Zn and Pb explain only 18.93 of the total variance. This study illustrates the usefulness of multivariate statistical techniques for evaluation and interpretation of large complex data sets to get better information about the heavy metal concentrations and design of monitoring network.
Major (sodium, potassium, calcium, magnesium) and minor elements (iron, copper, zinc, manganese) and one heavy metal (lead) of Cavendish banana flour and Dream banana flour were determined, and data were analyzed using multivariate statistical techniques of factor analysis and discriminant analysis. Factor analysis yielded four factors explaining more than 81% of the total variance: the first factor explained 28.73%, comprising magnesium, sodium, and iron; the second factor explained 21.47%, comprising only manganese and copper; the third factor explained 15.66%, comprising zinc and lead; while the fourth factor explained 15.50%, comprising potassium. Discriminant analysis showed that magnesium and sodium exhibited a strong contribution in discriminating the two types of banana flour, affording 100% correct assignation. This study presents the usefulness of multivariate statistical techniques for analysis and interpretation of complex mineral content data from banana flour of different varieties.
Multivariate statistical techniques such as multivariate analysis of variance (MANOVA) and discriminant analysis (DA) were applied for analyzing the data obtained from two rivers in the Penang State of Malaysia for the concentration of heavy metal ions (As, Cr, Cd, Zn, Cu, Pb, and Hg) using a flame atomic absorption spectrometry (F-AAS) for Cr, Cd, Zn, Cu, Pb, As and cold vapor atomic absorption spectrometry (CV-AAS) for Hg. The two locations of interest with 20 sampling points of each location were Kuala Juru (Juru River) and Bukit Tambun (Jejawi River). MANOVA showed a strong significant difference between the two rivers in terms of heavy metal concentrations in water samples. DA gave the best result to identify the relative contribution for all parameters in discriminating (distinguishing) the two rivers. It provided an important data reduction as it used four parameters (Zn, Pb, Cd and Cr) affording 100% correct assignations. Results indicated that the two rivers were different in terms of heavy metals concentrations in water, and the major difference was due to the contribution of Zn. A negative correlation was found between discriminate functions (DF) and Cr and As, whereas positive correlation was exhibited with other heavy metals. Therefore, DA allowed a reduction in the dimensionality of the data set, delineating a few indicator parameters responsible for large variations in heavy metal concentrations. Correlation matrix between the parameters exhibited a strong evidence of mutual dependence of these metals.
The addition of ribose to bovine or porcine gelatine solutions followed by heating at 95 °C yielded brown solutions with different pH, colour (CIE L(*) and b(*)) and absorbance (A(420*) values. These differences were used for gelatine powder identification, differentiation and quality control. Differentiation analysis of the Maillard reaction parameters was conducted using cluster analysis (CA) and confidence intervals (CI). The potential use of the method as a quality control procedure was evaluated by using statistical process control (SPC). CA revealed that the two types of gelatine could be classified into two different groups. CI (95% confidence) revealed that the absorbance and colour values could be used as indicators for differentiation between the two types of gelatine because the intervals between the Maillard reaction parameters of the samples were far apart. The methodology demonstrated good reproducibility because it behaved predictably based on the X¯-S charts generated from the SPC charts.
Time and temperature parameters of superheated steam (SHS) treatment were optimised using response surface methodology (RSM) for specific lipoxygenase (LOX) activity in soya beans and crude protein content in soya milk. The optimal SHS treatment was obtained at 9.3 min and 119 °C. The predicted values of specific LOX activity and crude protein content by RSM were 0.0098 μmol/(min mg protein) and 3.2%, respectively. These values were experimentally verified to be 0.0081 ± 0.0002 μmol/(min mg protein) and 3.0 ± 0.1%, respectively. Sensory evaluation showed that the beany flavour of soya milk produced from SHS treated soya beans was significantly weaker (P