Displaying publications 1 - 20 of 54 in total

Abstract:
Sort:
  1. Ramesh, S., Shanti, R., Chin, S.F.
    ASM Science Journal, 2011;5(1):19-26.
    MyJurnal
    In this present study, a series of polymer electrolyte thin films were synthesized by incorporating different ratios of lithium triflate (LiCF3SO3) in a low molecular weight polyvinyl chloride (PVC) matrix by the solution casting technique. The incorporation of LiCF3SO3 suppressed the high degree of crystallinity in PVC enabling the system to possess an appreciable ionic conductivity. The ionic conductivity of the samples, with different LiCF3SO3 content, was determined by the aid of ac impedance spectroscopy. The highest ionic conductivity of 4.04  10–9 S cm–1 was identified for the composition of PVC: LiCF3SO3 (75:25). Further understanding of the ionic conductivity mechanism was based on temperature-dependent conductivity data which obeyed Arrhenius theory, indicating that the ionic conductivity enhancement was thermally assisted. The possible dipole-dipole interaction between the chemical constituents was confirmed with changes in cage peak, analysed using Fourier transform infrared spectroscopy.
  2. Bang LT, Ramesh S, Purbolaksono J, Long BD, Chandran H, Ramesh S, et al.
    Biomed Mater, 2015 Aug;10(4):045011.
    PMID: 26225725 DOI: 10.1088/1748-6041/10/4/045011
    Interconnected porous tricalcium phosphate ceramics are considered to be potential bone substitutes. However, insufficient mechanical properties when using tricalcium phosphate powders remain a challenge. To mitigate these issues, we have developed a new approach to produce an interconnected alpha-tricalcium phosphate (α-TCP) scaffold and to perform surface modification on the scaffold with a composite layer, which consists of hybrid carbonate apatite / poly-epsilon-caprolactone (CO3Ap/PCL) with enhanced mechanical properties and biological performance. Different CO3Ap combinations were tested to evaluate the optimal mechanical strength and in vitro cell response of the scaffold. The α-TCP scaffold coated with CO3Ap/PCL maintained a fully interconnected structure with a porosity of 80% to 86% and achieved an improved compressive strength mimicking that of cancellous bone. The addition of CO3Ap coupled with the fully interconnected microstructure of the α-TCP scaffolds coated with CO3Ap/PCL increased cell attachment, accelerated proliferation and resulted in greater alkaline phosphatase (ALP) activity. Hence, our bone substitute exhibited promising potential for applications in cancellous bone-type replacement.
  3. Bang LT, Shi R, Bui Duc L, Ramesh S, Shi X, Sugiura Y, et al.
    Biomed Mater, 2020 Jan 08.
    PMID: 31914435 DOI: 10.1088/1748-605X/ab6939
    Titainum (Ti) implants have been successfully used in orthopaedic and dental surgery. However, the poor early bone tissue integration is still a common failure. This could be modulated by improving material bonding or adhesion directly to bone though a surface roughening and/or a bioresorbable and osteoconductive coating. In this study, we report on the biological behavious of the Ti substrate with modified surface roughness and/or bioactive coating. The roughened Ti surface was prepared by acid etching reaction, and the calcium carbonate (CaCO3) coating on the substrates was synthesized by hydrothermal treatment of Ti in calcium citrate complexes. The study demonstrated that surface roughing of Ti alone did not improve the biological reponse of the MC3T3-E1 cells, however, CaCO3 coating on smooth Ti surface increased cell responses, and the affects were further enhanced in combination with Ti surface roughening. Larger cell area, greater cell proliferation and increased bone-like nodule formation were obtained on the CaCO3 coating of the roughened Ti surface. This was also supported by a higher ALP value obtained for the the coatings of roughened Ti surface. The cell behaviours found in the current study support further development of calcium carbonate coatings towards clinical application.
  4. Omar FS, Duraisamy N, Ramesh K, Ramesh S
    Biosens Bioelectron, 2016 May 15;79:763-75.
    PMID: 26774092 DOI: 10.1016/j.bios.2016.01.013
    Nicotinamide Adenine Dinucleotide (NADH) is an important coenzyme in the human body that participates in many metabolic reactions. The impact of abnormal concentrations of NADH significantly causes different diseases in human body. Electrochemical detection of NADH using bare electrode is a challenging task especially in the presence of main electroactive interferences such as ascorbic acid (AA), uric acid (UA) and dopamine (DA). Modified electrodes have been widely explored to overcome the problems of poor sensitivity and selectivity occurred from bare electrodes. This review gives an overview on the progress of using conducting polymers, polyelectrolyte and its composites (co-polymer, carbonaceous, metal, metal oxide and clay) based modified electrodes for the sensing of NADH. In addition, developments on the fabrication of numerous conducting polymer composites based modified electrodes are clearly described.
  5. Ramesh S, Shanti R, Morris E
    Carbohydr Polym, 2013 Jan 2;91(1):14-21.
    PMID: 23044100 DOI: 10.1016/j.carbpol.2012.07.061
    Polymer electrolytes were developed by solution casting technique utilizing the materials of cellulose acetate (CA), lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) and deep eutectic solvent (DES). The DES is synthesized from the mixture of choline chloride and urea of 1:2 ratios. The increasing DES content well plasticizes the CA:LiTFSI:DES matrix and gradually improves the ionic conductivity and chemical integrity. The highest conducting sample was identified for the composition of CA:LiTFSI:DES (28 wt.%:12 wt.%:60 wt.%), which has the greatest ability to retain the room temperature ionic conductivity over the entire 30 days of storage time. The changes in FTIR cage peaks upon varying the DES content in CA:LiTFSI:DES prove the complexation. This complexation results in the collapse of CA matrix crystallinity, observed from the reduced intensity of XRD diffraction peaks. The DES-plasticized sample is found to be more heat-stable compared to pure CA. Nevertheless, the addition of DES diminishes the CA:LiTFSI matrix's heat-resistivity but at the minimum addition the thermal stability is enhanced.
  6. Liew CW, Ramesh S
    Carbohydr Polym, 2015 Jun 25;124:222-8.
    PMID: 25839815 DOI: 10.1016/j.carbpol.2015.02.024
    Biopolymer electrolytes containing corn starch, lithium hexafluorophosphate (LiPF6) and ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate (BmImPF6) are prepared by solution casting technique. Temperature dependence-ionic conductivity studies reveal Vogel-Tamman-Fulcher (VTF) relationship which is associated with free volume theory. Ionic liquid-based biopolymer electrolytes show lower glass transition temperature (Tg) than ionic liquid-free biopolymer electrolyte. X-ray diffraction (XRD) studies demonstrate higher amorphous region of ionic liquid-added biopolymer electrolytes. In addition, the potential stability window of the biopolymer electrolyte becomes wider and stable up to 2.9V. Conclusively, the fabricated electric double layer capacitor (EDLC) shows improved electrochemical performance upon addition of ionic liquid into the biopolymer electrolyte. The specific capacitance of EDLC based on ionic liquid-added polymer electrolyte is relatively higher than that of ionic liquid-free polymer electrolyte as depicted in cyclic voltammogram.
  7. Ramesh S, Shanti R, Morris E
    Carbohydr Polym, 2012 Jan 04;87(1):701-706.
    PMID: 34663024 DOI: 10.1016/j.carbpol.2011.08.047
    A series of polymer electrolytes composed of corn starch (CS), lithium bis(trifluoromethanesulfonyl)imide (LITFSI) and deep eutectic solvent (DES) were fabricated by solution casting technique. The DES was synthesized from a mixture of choline chloride and urea at a molar ratio of 1:2. The addition of DES is crucial in enhancing the room temperature ionic conductivity by increasing the amorphous elastomeric phase in CS:LITFSI matrix. The ionic transport mechanism is improved and appreciable amount of ion conducting polymer electrolytes is produced. The highest ionic conductivity achieved for the polymer electrolyte composition CS:LiTFSI:DES (14wt.%:6wt.%:80wt.%) is 1.04×10-3Scm-1. The anomalies that were observed with the addition of DES upon formation of neutral ion multiples were visually revealed by the SEM micrographs. The possible dipole-dipole interaction between the constituents was visualized by the FTIR spectroscopy upon change in cage peaks.
  8. Soudagar MEM, Kiong TS, Jathar L, Nik Ghazali NN, Ramesh S, Awasarmol U, et al.
    Chemosphere, 2024 Apr;353:141540.
    PMID: 38423144 DOI: 10.1016/j.chemosphere.2024.141540
    The development of algae is seen as a potential and ecologically sound approach to address the increasing demands in multiple sectors. However, successful implementation of processes is highly dependent on effective growing and harvesting methods. The present study provides a complete examination of contemporary techniques employed in the production and harvesting of algae, with a particular emphasis on their sustainability. The review begins by examining several culture strategies, encompassing open ponds, closed photobioreactors, and raceway ponds. The analysis of each method is conducted in a systematic manner, with a particular focus on highlighting their advantages, limitations, and potential for expansion. This approach ensures that the conversation is in line with the objectives of sustainability. Moreover, this study explores essential elements of algae harvesting, including the processes of cell separation, dewatering, and biomass extraction. Traditional methods such as centrifugation, filtration, and sedimentation are examined in conjunction with novel, environmentally concerned strategies including flocculation, electro-coagulation, and membrane filtration. It evaluates the impacts on the environment that are caused by the cultivation process, including the usage of water and land, the use of energy, the production of carbon dioxide, and the runoff of nutrients. Furthermore, this study presents a thorough examination of the current body of research pertaining to Life Cycle Analysis (LCA) studies, presenting a perspective that emphasizes sustainability in the context of algae harvesting systems. In conclusion, the analysis ends up with an examination ahead at potential areas for future study in the cultivation and harvesting of algae. This review is an essential guide for scientists, policymakers, and industry experts associated with the advancement and implementation of algae-based technologies.
  9. Rajhans V, Mohammed CA, Ve RS, Prabhu A
    Educ Health (Abingdon), 2021 7 3;34(1):22-28.
    PMID: 34213440 DOI: 10.4103/efh.EfH_69_20
    Background: Current trends in health professions education are aligned to meet the needs of the millennial learner. The aim of this study was to identify learners' perceptions of an ongoing journal club (JC) activity in the optometry curriculum and evaluate the utility and efficiency of this method in promoting student learning.

    Methods: A qualitative approach with a phenomenological research design was adopted. The perceptions of undergraduate and postgraduate optometry students about JCs were captured using focus group discussions. A narrative thematic analysis was done using the verbatim transcripts and moderator's notes. Results are reported using "consolidated criteria for reporting qualitative research" guidelines.

    Results: A total of 33 optometry students participated in the study. Data analysis revealed three major themes related to (i) The ongoing practice of JC, (ii) student perceptions of JC and its relevance in facilitating student learning, and (iii) suggestions for modification of JC for achieving optimal educational outcomes.

    Discussion: Student feedback indicates that an instructional redesigning of JC is necessary, considering the characteristics and expectations of the current generation of learners and the rapid strides made in the field of educational technology. The recommendations provided are likely to resurrect an age-old approach that still has educational relevance if blended with collaborative learning formats and appropriate technology.

  10. Kannan R, Reddiar Y, Ramakrishnan K, Eastaff MS, Ramesh S
    F1000Res, 2021;10:1052.
    PMID: 36225238 DOI: 10.12688/f1000research.73234.2
    Background: Banks and financial institutions are vulnerable to money laundering (ML) as a result of crime proceeds infiltrating banks in the form of significant cash deposits. Improved financial crime compliance processes and systems enable anti-ML (AML) analysts to devote considerable time and effort to case investigation and process quality work, thereby lowering financial risks by reporting suspicious activity in a timely and effective manner. This study uses Job Characteristics Theory (JCT) to evaluate the AML system through the job satisfaction and motivation of its users. The purpose of this study is to determine how satisfied AML personnel are with their jobs and how motivated they are to work with the system. Methods: This cross-sectional study used JCT to investigate the important elements impacting employee satisfaction with the AML system. The five core dimensions of the job characteristics were measured using a job diagnostic survey. The respondents were employees working in the AML department of a Malaysian bank, and the sample group was chosen using a purposive sampling approach. A total of 100 acceptable replies were gathered and analysed using various statistical approaches. A motivating potential score was generated for each employee based on five main job characteristics. Results: Findings revealed that five core job characteristics, namely, skill diversity, task identity, task importance, autonomy and feedback, positively influence the AML system employees' job satisfaction. However, skill variety and autonomy are found to be low, which are reflected in the poor motivating potential score. Conclusion: This study examined the characteristics of the AML system and its users' job satisfaction. Findings revealed that task significance is the most widely recognised characteristic, followed by feedback and task identity. However, there is a lack of skill variety and autonomy, which must be addressed to improve employee satisfaction with the AML system.
  11. Bashir S, Teo YY, Ramesh S, Ramesh K, Mushtaq MW
    Int J Biol Macromol, 2018 Oct 01;117:454-466.
    PMID: 29807081 DOI: 10.1016/j.ijbiomac.2018.05.182
    Novel pH sensitive N-succinyl chitosan-g-poly (acrylic acid) hydrogels were synthesized through free radical mechanism. Rheometer was used to observe the mechanical strength of the hydrogels. In vitro degradation was conducted in SIF (pH 7.4). The effect of concentration of monomers, initiator, and crosslinking agent and pH and ionic strength of NaCl, CaCl2, and AlCl3 on swelling of the hydrogels was observed. The results showed that equilibrium swelling ratio was highly influenced by concentration of monomers, initiator, and crosslinking agent concentration, and pH and salt solutions of NaCl, CaCl2, and AlCl3. The swelling kinetics revealed that swelling followed non-Fickian anomalous transport. Furthermore, theophylline loading (DL %) and encapsulation efficiency (EE %) of the hydrogels was in the range of 15.5 ± 0.15-22.8 ± 0.06% and 62 ± 0.15-91 ± 0.26%, respectively. The release of theophylline in physiological mediums was strongly influenced by the pH. The theophylline release was in the range of 51 ± 0.20-92 ± 0.12% in SIF and 7.4 ± 0.02-14.9 ± 0.03% in SGF (pH 1.2), respectively. The release data fitted well to Korsmeyer-Peppas model. The chemical activity of the theophylline suggested that drug maintained its chemical activity after release in vitro. The results suggest that synthesized hydrogels are excellent drug carriers.
  12. Duraisamy N, Numan A, Fatin SO, Ramesh K, Ramesh S
    J Colloid Interface Sci, 2016 Jun 01;471:136-144.
    PMID: 26995554 DOI: 10.1016/j.jcis.2016.03.013
    In this work, we demonstrate the influence of nickel oxides with divergent particle sizes as the working electrodes for supercapacitor application. The nanostructured nickel oxide (NiO) is synthesized via facile sonochemical method, followed by calcination process. The crystallinity and surface purity of prepared samples are clearly examined by X-ray diffraction and Raman analysis. NiO crystallinity is significantly increased with increasing calcination temperatures. The surface analysis confirmed that the calcination at 250°C exhibited nanoclutser like NiO with average particle size of ∼6nm. While increasing the calcination temperature beyond 250°C, hexagonal shaped NiO is observed with enhanced particle sizes. The electrochemical performance confirmed the good redox behavior of NiO electrodes. Moreover, NiO with average particle size of ∼6nm exhibited high specific capacitance of 449F/g at a scan rate of 5mV/s compared to other samples with particle sizes of ∼21nm (323F/g) and ∼41nm (63F/g). This is due to the good ion transfer mechanism and effective electrochemical utilization of the working electrode.
  13. Huda N, Raman AAA, Bello MM, Ramesh S
    J Environ Manage, 2017 Dec 15;204(Pt 1):75-81.
    PMID: 28865309 DOI: 10.1016/j.jenvman.2017.08.028
    The main problem of landfill leachate is its diverse composition comprising many persistent organic pollutants which must be removed before being discharge into the environment. This study investigated the treatment of raw landfill leachate using electrocoagulation process. An electrocoagulation system was designed with iron as both the anode and cathode. The effects of inter-electrode distance, initial pH and electrolyte concentration on colour and COD removals were investigated. All these factors were found to have significant effects on the colour removal. On the other hand, electrolyte concentration was the most significant parameter affecting the COD removal. Numerical optimization was also conducted to obtain the optimum process performance. Under optimum conditions (initial pH: 7.73, inter-electrode distance: 1.16 cm, and electrolyte concentration (NaCl): 2.00 g/L), the process could remove up to 82.7% colour and 45.1% COD. The process can be applied as a pre-treatment for raw leachates before applying other appropriate treatment technologies.
  14. Mehboob H, Tarlochan F, Mehboob A, Chang SH, Ramesh S, Harun WSW, et al.
    J Mater Sci Mater Med, 2020 Aug 20;31(9):78.
    PMID: 32816091 DOI: 10.1007/s10856-020-06420-7
    The current study is proposing a design envelope for porous Ti-6Al-4V alloy femoral stems to survive under fatigue loads. Numerical computational analysis of these stems with a body-centered-cube (BCC) structure is conducted in ABAQUS. Femoral stems without shell and with various outer dense shell thicknesses (0.5, 1.0, 1.5, and 2 mm) and inner cores (porosities of 90, 77, 63, 47, 30, and 18%) are analyzed. A design space (envelope) is derived by using stem stiffnesses close to that of the femur bone, maximum fatigue stresses of 0.3σys in the porous part, and endurance limits of the dense part of the stems. The Soderberg approach is successfully employed to compute the factor of safety Nf > 1.1. Fully porous stems without dense shells are concluded to fail under fatigue load. It is thus safe to use the porous stems with a shell thickness of 1.5 and 2 mm for all porosities (18-90%), 1 mm shell with 18 and 30% porosities, and 0.5 mm shell with 18% porosity. The reduction in stress shielding was achieved by 28%. Porous stems incorporated BCC structures with dense shells and beads were successfully printed.
  15. Khanmirzaei MH, Ramesh S, Ramesh K
    J Nanosci Nanotechnol, 2020 Apr 01;20(4):2423-2429.
    PMID: 31492257 DOI: 10.1166/jnn.2020.17192
    Solid polymer electrolytes (SPEs) were prepared using rice starch as the polymer, sodium iodide (NaI) as the salt and 1-hexyl-3-methylimidazolium iodide (HMII) as the ionic liquid (IL). The solution casting technique was used for preparation of the PEs. The ionic conductivity and temperaturedependent properties of the PEs were measured and all the SPEs were found to follow the Arrhenius thermal activated model. Ionic conductivity increased as the percentage of ILs increased. The SPE containing 20% (wt) of HMII IL showed the highest ionic conductivity of 1.83×10-3 S/cm. Spectral and structural characterization of the PEs were performed by Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD), respectively. The results of thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) indicate that the decomposition temperature (Tdc), glass transition temperatures (Tg) and melting points (Tm) shifted when complexation with HMII occurred. The PEs were used to fabricate dye-sensitized solar cells (DSSCs) and the DSSCs were analyzed under a 1-sun simulator. The SPE with the highest ionic conductivity displayed a short circuit current density (Jsc) of 9.07 (mA cm-2), open circuit voltage (Voc) of 0.58 (V), a fill factor (FF) of 0.65 and had the highest energy conversion efficiency of 3.42%.
  16. Ramesh S, Yaghoubi A, Lee KY, Chin KM, Purbolaksono J, Hamdi M, et al.
    J Mech Behav Biomed Mater, 2013 Sep;25:63-9.
    PMID: 23726923 DOI: 10.1016/j.jmbbm.2013.05.008
    Forsterite (Mg2SiO4) because of its exceptionally high fracture toughness which is close to that of cortical bones has been nominated as a possible successor to calcium phosphate bioceramics. Recent in vitro studies also suggest that forsterite possesses good bioactivity and promotes osteoblast proliferation as well as adhesion. However studies on preparation and sinterability of nanocrystalline forsterite remain scarce. In this work, we use a solid-state reaction with magnesium oxide (MgO) and talc (Mg3Si4(OH)2) as the starting precursors to synthesize forsterite. A systematic investigation was carried out to elucidate the effect of preparatory procedures including heat treatment, mixing methods and sintering temperature on development of microstructures as well as the mechanical properties of the sintered forsterite body.
  17. Lal LPJ, Ramesh S, Parasuraman S, Natarajan E, Elamvazuthi I
    Materials (Basel), 2019 Sep 20;12(19).
    PMID: 31547117 DOI: 10.3390/ma12193057
    Nanosilica particles were utilized as secondary reinforcement to enhance the strength of the epoxy resin matrix. Thin glass fibre reinforced polymer (GFRP) composite laminates of 3 ± 0.25 mm were developed with E-Glass mats of 610 GSM and LY556 epoxy resin. Nanosilica fillers were mixed with epoxy resin in the order of 0.25, 0.5, 0.75 and 1 wt% through mechanical stirring followed by an ultrasonication method. Thereafter, the damage was induced on toughened laminates through low-velocity drop weight impact tests and the induced damage was assessed through an image analysis tool. The residual compression strength of the impacted laminates was assessed through compression after impact (CAI) experiments. Laminates with nanosilica as secondary reinforcement exhibited enhanced compression strength, stiffness, and damage suppression. Results of Fourier-transform infrared spectroscopy revealed that physical toughening mechanisms enhanced the strength of the nanoparticle-reinforced composite. Failure analysis of the damaged area through scanning electron microscopy (SEM) evidenced the presence of key toughening mechanisms like damage containment through micro-cracks, enhanced fiber-matrix bonding, and load transfer.
  18. Fattah NFA, Ng HM, Mahipal YK, Numan A, Ramesh S, Ramesh K
    Materials (Basel), 2016 Jun 06;9(6).
    PMID: 28773573 DOI: 10.3390/ma9060450
    Solid polymer electrolyte (SPE) composed of semi-crystalline poly (vinylidene fluoride-hexafluoropropylene) [P(VdF-HFP)] copolymer, 1-ethyl-3-methylimidazolium bis (trifluoromethyl sulphonyl) imide [EMI-BTI] and graphene oxide (GO) was prepared and its performance evaluated. The effects of GO nano-filler were investigated in terms of enhancement in ionic conductivity along with the electrochemical properties of its electrical double layer capacitors (EDLC). The GO-doped SPE shows improvement in ionic conductivity compared to the P(VdF-HFP)-[EMI-BTI] SPE system due to the existence of the abundant oxygen-containing functional group in GO that assists in the improvement of the ion mobility in the polymer matrix. The complexation of the materials in the SPE is confirmed in X-ray diffraction (XRD) and thermogravimetric analysis (TGA) studies. The electrochemical performance of EDLC fabricated with GO-doped SPE is examined using cyclic voltammetry and charge-discharge techniques. The maximum specific capacitance obtained is 29.6 F∙g(-1), which is observed at a scan rate of 3 mV/s in 6 wt % GO-doped, SPE-based EDLC. It also has excellent cyclic retention as it is able keep the performance of the EDLC at 94% even after 3000 cycles. These results suggest GO doped SPE plays a significant role in energy storage application.
  19. Liew CW, Ramesh S
    Materials (Basel), 2014 May 21;7(5):4019-4033.
    PMID: 28788662 DOI: 10.3390/ma7054019
    Two different ionic liquid-based biopolymer electrolyte systems were prepared using a solution casting technique. Corn starch and lithium hexafluorophosphate (LiPF₆) were employed as polymer and salt, respectively. Additionally, two different counteranions of ionic liquids, viz. 1-butyl-3-methylimidazolium hexafluorophosphate (BmImPF₆) and 1-butyl-3-methylimidazolium trifluoromethanesulfonate (also known as 1-butyl-3-methylimidazolium triflate) (BmImTf) were used and studied in this present work. The maximum ionic conductivities of (1.47 ± 0.02) × 10(-4) and (3.21 ± 0.01) × 10(-4) S∙cm(-1) were achieved with adulteration of 50 wt% of BmImPF₆ and 80 wt% of BmImTf, respectively at ambient temperature. Activated carbon-based electrodes were prepared and used in supercapacitor fabrication. Supercapacitors were then assembled using the most conducting polymer electrolyte from each system. The electrochemical properties of the supercapacitors were then analyzed. The supercapacitor containing the triflate-based biopolymer electrolyte depicted a higher specific capacitance with a wider electrochemical stability window compared to that of the hexafluorophosphate system.
  20. Shan L, Tan CY, Shen X, Ramesh S, Kolahchi R, Hajmohammad MH, et al.
    Materials (Basel), 2022 Dec 15;15(24).
    PMID: 36556764 DOI: 10.3390/ma15248959
    Lightweight aluminum alloy components are often used to manufacture a variety of engineering components in many industries. In recent years, researchers have studied the effect of improving the mechanical properties of metal alloys by incorporating nano-carbon into its structure. In this study, the effect of the addition of 0.2, 0.5, and 1 wt% of multi-walled carbon nanotubes (MWCNTs) on the stress-strain behavior and creep phenomenon of an A356 aluminum alloy were studied. The effect of nickel coating on 0.2 wt% MWCNTs was also investigated. Samples were prepared using the stir-casting method. The results revealed that the grain size became finer when MWCNT nano-particulates were introduced. Although the MWCNTs were distributed homogeneously in the A356 matrix, as confirmed by FESEM analysis, there were some agglomerations observed in a specific area with dimensions smaller than 100 nm. Nevertheless, the addition of MWCNTs was found to be beneficial in enhancing the hardness of alloys containing 0.2 wt%, 0.2 wt% nickel-coated, 0.5 wt%, and 1 wt% MWCNTs by 9%, 24%, 32%, and 15%, respectively, as compared with the unreinforced A345 matrix. It was also found that the 0.5 wt% MWCNT-A356 matrix exhibited an improvement in the creep lifetime by more than two orders of magnitude.
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links