Displaying publications 1 - 20 of 173 in total

Abstract:
Sort:
  1. F. Nurhaziqah K., Sheng, C.K., Amin, K.A.M., Isa, M.I.N., Hassan, M.F., Ali, E.A.G.E., et al.
    ASM Science Journal, 2018;11(101):68-74.
    MyJurnal
    The new microelectronic products require the silicon (Si) wafer to be thinned to less than
    150 µm in thickness. Residual defect on the wafer surface that leads to wafer breakage with
    a rough surface still be produced by mechanical grinding. Thus, chemical etching method is
    essentially applied to produce a reliable thin wafer with smooth surface of desired thickness.
    In this work, we studied the wet chemical etching effect of different HNO3 concentrations on
    total thickness and weight loss, etch rate, morphological and structural properties of Si wafer
    in the mixtures of HNO3 and HF. The results showed that the total thickness and weight
    loss increases with the increasing of HNO3 concentration and etching time. Higher HNO3
    concentration causes higher etch rate, and the etch rate decreases at prolonged etching time.
    A smoother and clearer homogeneous Si surface image was observed by optical microscope as
    the etching time and HNO3 concentration increase. XRD analysis shows that the intensity
    of etched Si wafer is higher than the pure one, which might indicate the smoother surface
    formation after etching. The findings of present study can be valuably referred to produce
    a reliable and desired Si thin wafer which is crucial in integrated circuit fabrication.
  2. Hamzah, I.H., Sidek, O., Abd Manaf, A.
    ASM Science Journal, 2010;4(2):142-148.
    MyJurnal
    A preliminary study was carried out to fabricate a three electrode system based on electrochemical sensoring. The cyclic voltammetry (CV) technique was chosen to select the type of metal suitable for evaporation and to compare the results produced from the fabricated gold electrode with the conventional macro-electrode system. The methodology and apparatus used involved low cost apparatus and methodology such as soft lithography, wet-etching, thermal evaporation, direct current sputtering, polymethylmethacrylate moulding and polydimethylsiloxane coating. The experiment was conducted at a fixed scan rate of 100 mV/s by using 0.01 M K3Fe(CN)6 in 0.1M KCl and well known method using Randles-Sevcik equation, peak current ratio and voltage separation was used to analyze the characterization on the fabricated sensors. Electrodes of 6.5 mm2 and 0.26 mm2 were fabricated to prove the adsorption effect of the reactant and the influence of the electrode area on the value of the peak current. CV analysis proved that the fabricated sensor was reliable for a range of 24 h at 25ºC room temperature.
  3. Shaari, S., Ehsan, A.A., Abd-Rahman, M.K.
    ASM Science Journal, 2008;2(2):153-161.
    MyJurnal
    An optical code generating device for a portable optical access-card system was constructed using the plastic optical fibre (POF) waveguide coupler. The newly constructed device provided output light intensities which were used as optical codes in a portable optical access-card system. The construction of a basic 1 × 2 waveguide design combined two major components which were the asymmetric Y-junction splitter and the linear taper. A hollow waveguide structure was utilized as it provided more flexibility in guiding light rays. A basic 1 × 2 waveguide coupler was designed using the CAD tool and then the ray was traced using the non-sequential ray tracing tool. A linear relationship between the tap-off ratio and the waveguide tap-width enabled a higher-level hollow waveguide coupler to be designed using the simple cascading technique. Construction of a 1 × 4 and higher level waveguide coupler was easily realized using the basic 1 × 2 waveguide coupler design together with a simple cascading technique.
  4. Yusoff, M.H.M., Hassan, H.A., Hashim, M.R., Abd-Rahman, M.K.
    ASM Science Journal, 2008;2(2):139-148.
    MyJurnal
    The fabrication tolerance of a short and compact low refractive index grating waveguide polarisation splitter based on the principle of resonant tunnelling was analyzed in this study. The design utilised two grating waveguides with an intermediate conventional waveguide layer. The design and optimisation were conducted using the quasi 2-D effective index solver with global search algorithm. An optimum device operating at 1.55 μm wavelength was obtained at a length of 340 μm. The splitting ratios were calculated to be 36 dB and 15 dB, and the overall device transmission efficiencies, after considering the three-dimensional waveguide leakage loss, were estimated at 88% and 83% for tranverse magnetic and tranverse electric polarisation, respectively.
  5. Muhd-Yassin, S.Z., Harun, S.W., Ahmad, H., Abd-Rahman, M.K.
    ASM Science Journal, 2008;2(2):163-168.
    MyJurnal
    An efficient erbium/ytterbium co-doped fibre amplifier was demonstrated by using a dual-stage partial doublepass structure with a band-pass filter (BPF). The amplifier achieved the maximum small signal gain of 56 dB and the corresponding noise figure of 4.66 dB at 1536 nm with an input signal power and total pump power of –50 dBm and 140 mW, respectively. Compared with a conventional single-stage amplifier, the maximum gain enhancement of 16.99 dB was obtained at 1544 nm with the corresponding noise figure was improved by 2 dB. The proposed amplifier structure only used a single pump source with a partial double pass scheme to provide a high gain and dual-stage structure to provide the low noise figure.
  6. Babura, Babangida Ibrahim, Mohd Bakri Adam, Anwar Fitrianto, Abdul Rahim, A.S.
    ASM Science Journal, 2018;11(2):86-102.
    MyJurnal
    A boxplot is an exploratory data analysis (EDA) tool for a compact visual display of a distributional summary of a univariate data set. It is designed to capture all typical observations and displays the location, spread, skewness and the tail of the data. The precision of some of this functionality is considered to be more reliable for symmetric data type and thus less appropriate for skewed data such as the extreme data. Many observations from extreme data were mistakenly marked as outliers by the Tukey’s standard boxplot. A new boxplot implementation is presented which adopts a fence definition using the extent of skewness and enhances the plot with additional features such as a quantile region for the parameters of generalized extreme value (GEV) distribution in fitting an extreme data set. The advantage of the new superimposed region was illustrated in term of batch comparison of extreme samples and an EDA tool to determine search region or direction as contained in the optimisation routines of a maximum likelihood parameter estimation of GEV model. A simulated and real-life data were used to justify the advantages of the boxplot enhancement.
  7. Manimaran, R., Abdul-Rashid, H.A.
    ASM Science Journal, 2008;2(2):133-137.
    MyJurnal
    This paper proposes a signal-to-noise-ratio (SNR) improvement by using an external phase modulator that allowed flexible control of the spectrum amplitude by varying the modulation index for linewidth measurements. Compared with the conventional self-heterodyne detection technique, the results obtained in this study showed an SNR improvement as high as 10 dB. This 10 dB improvement in SNR could help to reduce the usage of a particular length of a single mode fibre (normally about 50 Km) when measuring a linewidth in the region of 10 kHz.
  8. Reza, F., Begum, T., Ahmed, A.L., Omar, H., Muzaimi, M., Abdullah, J.M.
    ASM Science Journal, 2012;6(1):39-45.
    MyJurnal
    The human brain generates different oscillations at different frequencies during various consciousness levels. When these brain waves synchronize with exogenous rhythmic stimulation, the brain experiences strong, yet relaxing emotion that could be involved in the formation of memory. We investigated the character of rhythmic oscillatory dynamics by electroencephalography (EEG) of subjects listening to a short verse of the Holy Quran compared to resting and Arabic news listening. The mean power amplitudes of each frequency band for wavelet-based time-frequency analysis were obtained from 5000 ms of segmented EEG recordings during rest, news and Quran listening conditions. The time series analysis of power from each of three conditions in each frequency band from the grand averaged data was then subjected to autocorrelation study. The results showed significant cyclic overall trends of increasing and decreasing patterns of power in the low frequency brain wave oscillation of different head regions especially global, frontal and temporal sites. These results provided a basis for prediction of the periodicity of the power of the oscillatory brain dynamics of delta and robustly in theta regions which occurred during Quran listening. Despite several limitations, our data offered a plausible scientific basis to the emotional induction during Quran listening that mimics recognized as data from music listening studies. This offered a promising perspective for future studies in translational neurophysiological, cognitive and biofeedback on Quran listening to modify brain behaviour in health and disease.
  9. Islam, M.R., Muthuraju, S., Tarmizi, C.H., Zulkifli, M.M., Osman, H., Mohamad, H., et al.
    ASM Science Journal, 2012;6(2):95-102.
    MyJurnal
    Epilepsy is a neurological disorder characterized by recurrent seizures resulting from excessive abnormal electrical discharges in the brain. Medicinal plants may play an invaluable role to discover the new antiepileptic drugs. The aim of the present study was to investigate the anticonvulsant activity of α-terpineol isolated from Myristica fragrans Hountt. The α-terpineol showed a significant inhibition of the seizure episodes and spikes in absence seizures model of Genetic Absence Epilepsy Rats from Strasbourg (GAERS) rats by using electroencephalography records. It showed dose-dependent anticonvulsant activity that was comparable to the known antiepileptic drug of diazepam. It showed a rapid onset and relatively short duration of anticonvulsant effects. The present findings suggest that α-terpineol might possess antiepileptic activities against the partial seizures of human because it prevented seizures in well-established genetic absence seizure animal model of GAERS rats.
  10. Begum, T., Reza, F., Abdullah, J.M.
    ASM Science Journal, 2011;5(2):115-121.
    MyJurnal
    Reflex epilepsy is usually induced by external stimulation, photosensitive epilepsy being the most common. Epilepsy induced by auditory stimulation is rarely studied. There are no currently published magnetoencephalographic (MEG) studies demonstrating the initiation of epileptic neuronal discharges by repeated auditory stimulations in temporal lobe epilepsy (TLE) patients. We retrospectively studied one TLE patient who underwent a MEG study to localize her epileptic focus. Auditory, somatosensory, visual and motor evoked potential studies were performed during the MEG recording. A single dipole method calculated equivalent current dipoles to localize the epileptic source. The least-squares minimization method was used to obtain the optimal solution with goodness-of-fit of greater than 80%. Periodic lateralized epileptiform discharges (PLEDs) were recorded in the temporal region when repeated auditory stimulations were done. We postulated that neuronal cortical suppression occurred during repeated stimulations which provoked epileptiform discharges (PLEDs) without any physical symptoms or aura. It was concluded that repeated stimulations could facilitate epileptiform discharges in focal area/areas in certain subjects.
  11. Momani, M.A., Yatim, B., Ali, M.A.M., Abdullah, M.
    ASM Science Journal, 2009;3(2):121-130.
    MyJurnal
    The paper examines the propagation direction and speed of large scale travelling ionospheric disturbances (LSTIDs) obtained from GPS observations of extreme geomagnetic storms during the 23rd solar cycle; these are the October 2003 and November 2003 geomagnetic storms. In the analysis, the time delay between total electron content (TEC) structures at Scott Base station (SBA) (Lat. –77.85º, Long. 166.76º), McMurdo (McM4), (Lat. –77.84º, Long. 166.95º), Davis (DAV1), (Lat. –68.58º, Long. 77.97º) and Casey station (CAS1) (Lat. –66.28º, Long. 110.52º) GPS stations as well as the distance between these stations were employed in the analysis. The measurements during the October 2003 storm showed obvious time delay between the TEC enhancement occurrences at SBA/MCM4, DAV1 and CAS1 stations. The time delay indicated a movement of the ionospheric structures from higher to lower latitudes in a velocity ranging between 0.8 km/s – 1.2 km/s. The first sudden TEC enhancement was observed at SBA/McM4 (Lat. –75.84º) followed by CAS1 station (Lat. –66.28º) and the final TEC enhancement was seen at DAV1 station (Lat. –68.58º) with TEC magnitude decreasing while moving from higher to lower latitudes. One important observation was that although the latitude of the CAS1 station was lower than the DAV1 station, the TEC enhancement was firstly seen at the CAS1 station due to the shorter distance between SBA and CAS1 compared with the distance between SBA and CAS1 of about 500 km. The TEC measurements during the November 2003 storm showed an opposite propagation direction (i.e. poleward direction from lower to higher latitudes) which was seen with a velocity ranging between 0.3 km/s – 0.4 km/s. As similar response was observed using vertical TEC measurements obtained from individual PRN satellites but with higher velocity ranges (1.2 km/s – 2.4 km/s during October
    and 0.5 km/s – 0.7 km/s during November). The equatorward or poleward expansion of LSTIDs during the October and November 2003 storms was probably caused by the disturbances in the neutral temperature which occurred close to the dayside convection throat or due to the neutral wind oscillation induced by atmospheric gravity waves launched from the aurora region.
  12. Khadijah, O., Lee, K.K., Abdullah, M.F.F.
    ASM Science Journal, 2010;4(2):103-112.
    MyJurnal
    Two sequential statistical experimental designs were used to screen and investigate the dependence of the amount of biodegradation of Procion Red MX-8B (PR-MX8B) on the fermentation variables. Fourteen factors were screened using the Plackett-Burman design. Among these factors, the most significant variables which included yeast extract, corn steep solids and starch influencing PR-MX8B decolourisation were statistically elucidated for optimization. The optimum concentrations of 5.00 g/l yeast extract, 2.99 g/l starch and 1.89 g/l corn steep solids were predicted by applying the Box-Behnken design to the second order polynomial model fitted to the results obtained. The best predicted optimal conditions verified experimentally yielded 72.11% while the predicted value from the polynomial model was 79.17%. The experimental values were in good agreement with the predicted values with a 90.81% degree of accuracy.
  13. Al-Mansoori, M.H., Mahdi, M.A., Iqbal, S.J., Abdullah, M.K.
    ASM Science Journal, 2008;2(2):107-113.
    MyJurnal
    In this paper, the tuning range characteristics of a multiwavelength L-band Brillouin-erbium fibre laser utilizing a linear cavity is described. The dependency of the Stokes signal tuning range on the laser’s pumping power and single mode fibre length is elaborated. The proposed laser configuration exhibited a wide tuning range of 11 nm from 1599 nm to 1610 nm. The maximum number of 28 output channels with a spacing of 10.5 GHz was achieved by setting the Brillouin pump wavelength and power at 1603.1 nm and 1.1 mW, respectively. The wider tuning range and higher number of Brillouin Stokes contributed to the higher efficiency of doublepass amplification in the erbium gain medium and also to the bidirectional generation of Brillouin Stokes in the single-mode fibre.
  14. Hashida, N.H., Abdullah, R.B.
    ASM Science Journal, 2008;2(1):65-73.
    MyJurnal
    This study was carried out to compare the ultrastructure of fresh, capacitated and acrosome-reacted sperm. The sperm was treated with heparin for capacitation and calcium ionophore for acrosome reaction induction. Sperm samples were then prepared for ultrastructural studies and examined by transmission electron microscopy (TEM). Ultrastructural changes in plasma and acrosomal membranes, shape of the mitochondria and outer dense fibres, in capacitated and acrosome-reacted sperm were evident. The plasma membrane of fresh sperm was loosely fitted around the sperm head and the acrosomal membrane was closely opposed to the nucleus. The plasma and acrosomal membranes of the capacitated sperm were expanded, but disintegrated in the acrosome-reacted sperm. Mitochondria of fresh sperm appeared to be rounded in shape with plasma membrane closely opposed to it and the nine outer dense fibres were almost regular rounded in shape. However, in both capacitated and acrosome-reacted sperm, the mitochondria were almost regular and elongated in shape whilst the outer dense fibres were irregular in shape in the capacitated and acrosome-reacted sperm. There were no noticeable morphological changes found in the axonemal complexes in fresh, capacitated and acrosome-reacted sperm. Ultrastructural studies are able to provide detailed information on sequential events involving numerous physiological changes during fertilization.
  15. Fazliah, S.N., Jaafar, S., Shamsuddin, S., Zainudin, Z., Hilmi, A.B., Razila, A.R., et al.
    ASM Science Journal, 2010;4(1):1-14.
    MyJurnal
    Stem cells from human extracted deciduous teeth (SHED) have the ability to multiply much faster and double their population in culture at a greater rate, indicating that it may be in a more immature state than other type of adult stem cells. Mesenchymal stem cells (MSC) from human primary molars were isolated and cultured in media supplemented with 20% fetal bovine serum. The MSCs were confirmed using CD 105 and CD 166 and the identification of the osteoblast cells were done using reverse transcriptase polymerase chain reaction (RT-PCR) analysis. Differentiated osteoblast cells (DOC) were characterized by alkaline phosphotase and von Kossa staining followed by immunocytochemistry staining using osteocalcin and osteonectin antibodies. Further validation of SHED was done by RT-PCR to detect the presence of insulin-like growth factor 2 (IGF-2) and discoidin domain tyrosine kinase-2 (DDTK-2) transcripts, while the presence of Runx-2 mRNA was used to characterize DOC. The results showed that SHED was found positive for CD 105 and CD 166 and could differentiate into osteoblast, bone forming cells. The findings revealed the presence of distinct MSC population which had the capability to generate living human cells that could be a possible source for tissue engineering in the future.
  16. Abraham, Martin
    ASM Science Journal, 2012;6(1):67-70.
    MyJurnal
    The pursuit, initiation and establishment of multi-stakeholder partnerships, including with the private sector, is often a critical component of attaining and achieving the success and sustainability of many projects the world over. However, the soliciting and securing of socially, economically and environmentally constructive engagements between the private sector on the one hand, and the NGOs, CBOs and local communities on the other hand, is in reality much easier said than done. Notably, since most private sector corporations undoubtedly tend to leave behind various "ecological footprints", differing only in their size and depth, stemming from their respective forms and functions, and their ensuing impacts and implications. The interplay between the civil society and the private sector, especially for resource mobilization. (Copied from article).
  17. Mahdi, M.A., Sheih, S.J., Al-Mansoori, M.H., Zamzuri, A.K., Adikan, F.R.M.
    ASM Science Journal, 2008;2(2):115-122.
    MyJurnal
    A four-stage erbium-doped fibre amplifier with the gain bandwidth of 35 nm is demonstrated. The amplifier was designed to include a dispersion compensating module to compensate the accumulated dispersion by signals. The amplifier design permited some dynamic features such as the amplifier’s gain could be adjusted from 15 dB to 30 dB by varying the input signal power from –26 dBm to 8 dBm. The maximum output power of 23 dBm was obtained with a maximum allowable gain flatness of 1.5 dB.
  18. Azrul Ghazali, Sivadass Thiruchelvam, Kamal Nasharuddin Mustapha, Ahmad Kamal Kadir, Fatin Faiqa Norkhairi, Nora Yahya, et al.
    ASM Science Journal, 2018;11(2):117-123.
    MyJurnal
    Series of catastrophic floods that we have witnessed over the last decade in Malaysia have necessitated the adoption of reliable early warning system. Ultimate concern during any event of natural or manmade disaster would be information dissemination to lessen the disaster impact on lives and property. The Bertam Valley incident in the wee hours of 23rd October 2013 has been considered as the game changer of how we view the role of vulnerable communities in facing dam-related disasters. Empowerment of local communities has been considered as vital in disaster management, as they are often the first responders to disaster. Local Community-Based Early Warning System (CBEWS) is a smart mechanism operated by the communities. This study revolves around the actual implementation of such system in Cameron Highlands in the effort of increasing human resilience towards damrelated disasters. While establishing the system, the Bertam Valley community has received support from different individuals and organisations. It is paramount that the community develops and maintains close coordination and strong links with these stakeholders. The performance of early warning systems can be evaluated via key parameters such as timeliness, accuracy, reliability, user friendliness, flexibility, and costs & benefits.
  19. Harun, S.W., Sulaiman, A.H., Ahmad, H.
    ASM Science Journal, 2009;3(1):27-30.
    MyJurnal
    We demonstrate a multi-wavelength light source using a semiconductor optical amplifier (SOA) in conjunction with an array waveguide grating (AWG). The experimental results showed more than 20 channels with a wavelength separation of 0.8 nm and an optical signal-to-noise ratio of more than 10 dB under room temperature. The channels operated at the wavelength region from 1530.4 nm to 1548.6 nm, which corresponded to AWG filtering wavelengths with SOA drive current of 350 mA. The proposed light source had the advantages of a simple and compact structure, multi-wavelength operation and the system could be upgraded to generate more wavelengths.
  20. Harun, S.W., Tamjis, M.R., Muhd-Yassin, S.Z., Abd-Rahman, M.K., Ahmad, H.
    ASM Science Journal, 2007;1(2):129-133.
    MyJurnal
    This paper demonstrates an erbium/ytterbium co-doped fi bre amplifi er (EYDFA) which used a pumping wavelength of 1058 nm, whereby the amplifi cation was assisted by the energy transfer between Yb and Er ions. The energy transfer increased the erbium doping concentration limit that was imposed by concentration quenching in erbium-doped fi bre. The optimum length was obtained at 4m~6m for erbium/ytterbium co-doped fi bre with Er ion concentration of 1000 p.p.m. This enabled the development of a compact amplifi er with a shorter gain medium compared to erbium-doped fi bre amplifi ers which use a gain medium of up to 15 m. A 1058 nm pumping wave-length was used for the EYDFA, as 1480 nm pumping resulted in severely degraded gain and noise fi gures because the energy transfer could not be achieved. The use of the optical isolator improved the small signal gain and noise fi gure by about 4.8 dB and 1.6 dB, respectively. Without the isolator, gain saturation and a noise fi gure penalty were observed due to the oscillating laser which was created at around 1534 nm by spurious refl ection. This showed that the usage of optical isolators was an important aspect to consider when designing an EYDFA.
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links