A novel polyoxometalate-based electrode was developed by incorporating phosphotungstic acid (PWA) in nylon-6,6 nanofiber, followed by carbonization. The developed PWA-carbon nanofiber (PWA-CNF) showed the characteristics of the dual-scale porosity of micro- and mesoporous substrate with surface area of around 684 m2 g-1. The compound exhibited excellent stability in vanadium electrolyte and battery cycling. Evaluation of electrocatalytic properties toward V2+/V3+ and VO2+/VO2+ redox couples indicated promising advantages in electron transfer kinetics and increasing energy efficiency, particularly for the VO2+/VO2+ couple. Moreover, the developed electrode exhibited substantially improved energy efficiency (14% higher than that of pristine carbon felt) in the single cell vanadium redox flow battery. This outstanding performance was attributed to high surface area and abundant oxygen-containing linkages in the developed electrode.
An integrated cohesive band structure of carbon nanotubes (CNTs) applicable to all chirality directions (n, m), starting from the Dirac cone of a graphene nanolayer in k-space, is demarcated, in direct contrast to dissimilar chiral and achiral versions in the published literature. The electron wave state of a CNT is quantized into one-dimensional (1-D) nanostructure with a wrapping mode, satisfying the boundary conditions from one Dirac K-point to an equivalent neighboring one with an identical phase and returning to the same K point. The repetitive rotation for an identical configuration with added band index (n-m)mod3, yields one metallic (M) with zero bandgap corresponding to (n-m)mod3 = 0, semiconducting state SC1 with (n-m)mod3 = 1 and SC2 with (n-m)mod3 = 2. The band gap and effective mass of SC2 state are twice as large as those of SC1 state. A broad-spectrum expression signifying the linear dependence of the effective mass on the bandgap is obtained. Both the Fermi energy and the intrinsic velocity limiting the current to the saturation level is calculated as a function of the carrier concentration. Limitations of the parabolic approximation are pointed out. Several new features of the band structure are acquired in a seamlessly unified mode for all CNTs, making it suitable for all-encompassing applications. Applications of the theory to high-field transport are advocated with an example of a metallic CNT, in agreement with experimental observations. The mechanism behind the breakdown of the linear current-voltage relation of Ohm's law and the associated surge in resistance are explained on the basis of the nonequilibrium Arora's distribution function (NEADF). These results are important for the performance evaluation and characterization of a variety of applications on CNT in modern nanoscale circuits and devices.
As an indispensable energy source, ammonia plays an essential role in agriculture and various industries. Given that the current ammonia production is still dominated by the energy-intensive and high carbon footprint Haber-Bosch process, photocatalytic nitrogen fixation represents a low-energy consuming and sustainable approach to generate ammonia. Heterostructured photocatalysts are hybrid materials composed of semiconductor materials containing interfaces that make full use of the unique superiorities of the constituents and synergistic effects between them. These promising photocatalysts have superior performances and substantial potential in photocatalytic reduction of nitrogen. In this review, a wide spectrum of recently developed heterostructured photocatalysts for nitrogen fixation to ammonia are evaluated. The fundamentals of solar-to-ammonia conversion, basic principles of various heterojunction photocatalysts and modification strategies are systematically reviewed. Finally, a brief summary and perspectives on the ongoing challenges and directions for future development of nitrogen photofixation catalysts are also provided.
Ferroelectric photoelectrodes, other than conventional semiconductors, are alternative photo-absorbers in the process of water splitting. However, the capture of photons and efficient transfer of photo-excited carriers remain as two critical issues in ferroelectric photoelectrodes. In this work, we overcome the aforementioned issues by decorating the ferroelectric BiFeO3 (BFO) surface with Au nanocrystals, and thus improving the photoelectrochemical (PEC) performance of BFO film. We demonstrate that the internal field induced by the spontaneous polarization of BFO can (1) tune the efficiency of the photo-excited carriers' separation and charge transfer characteristics in bare BFO photoelectrodes, and (2) modulate an extra optical absorption within the visible light region, created by the surface plasmon resonance excitation of Au nanocrystals to capture more photons in the Au/BFO heterostructure. This study provides key insights for understanding the tunable features of PEC performance, composed of the heterostructure of noble metals and ferroelectric materials.
Lithium-sulfur (Li-S) batteries have attracted great attention owing to their excellent electrochemical properties, such as the high discharge voltage of 2.3 V, specific capacity of 1675 mA h g(-1) and energy density of 2600 Wh kg(-1). The widely used slurry made electrodes of Li-S batteries are plagued by the serious shuttle effect and insulating nature of sulfur. Herein, a reduced graphene oxide coated porous carbon nanofiber flexible paper (rGO@S-PCNP) was fabricated and directly used as an additive-free cathode for Li-S batteries. The results show that the rGO@S-PCNP is certified to be effective at relieving the shuttle effect and improving the conductivity, thus achieving high electrochemical performance. The rGO@S-PCNP composite with a sulfur content of 58.4 wt% delivers a high discharge capacity of 623.7 mA h g(-1) after 200 cycles at 0.1 C (1 C = 1675 mA g(-1)) with the average Coulombic efficiency of 97.1%. The excellent cyclability and high Coulombic efficiency indicate that the as-prepared rGO@S-PCNP composite paper can be a promising cathode for lithium-sulfur batteries, and is envisioned to have great potential in high energy density flexible power devices. This facile strategy brings great significance for large-scale industrial fabrication of flexible lithium-sulfur batteries.
Tin-based materials have been intensively studied as attractive candidates for high-capacity and long-cycle-life anodes in Li-ion batteries (LIBs) owing to their low cost and high energy density. However, they all suffer from severe structural decay during the lithium ion insertion/extraction process, which results in deterioration in the overall performance of the batteries. To mitigate this problem, we have synthesized a Mo-doped SnO2 nanostructure via a facile hydrothermal method, which then fragmented into ultrafine particles after dozens of cycles. The fracture-resistant size and ample contact with Super-P and Li2O greatly improved the electrochemical kinetics and cyclability to deliver a reversible capacity of 670 mA h g-1 after 700 cycles, which demonstrated the potential suitability of Mo-doped SnO2 nanoparticles as a long-cycle-life anode material. Then, the compounds were uniformly dispersed in carbon nanofibers and reduced in situ to prepare a free-standing anode via electrospinning and carbonization. When used directly as an anode in LIBs (without a polymeric binder or conductive agent, as well as a current collector), the nanofiber membrane anode delivered comparable cycling performance and capacity to that of a slurry-coated electrode.
Liquid-exfoliated 2D transition metal disulfides (TMDs) are potential substitutes for poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as hole transport layers (HTLs) in Organic Solar Cells (OSCs). Herein, high-yield and high-quality WS2 flake layers are prepared by comprehensively controlling the initial concentration, sonication processing time and centrifugal speed. The WS2 layers deposited on in situ transparent indium tin oxide (ITO) without plasma treatment show higher uniformity and conductivity than that formed on ITO after plasma treatment. With a significant increase in the short-circuit current density (JSC), the power conversion efficiency (PCE) of PM6:Y6-based non-fullerene OSCs using optimized WS2 as the HTL is higher than that using PEDOT:PSS as the HTL(15.75% vs. 15.31%). Combining the morphology characteristics with carrier recombination characteristics, the higher quality of the ITO/WS2 composite substrate leads to better charge transport and a lower bimolecular recombination rate in OSCs, thereby improving the device performance.
The usability and tunability of the essential InP-InGaAs material combination in nanowire-based quantum wells (QWs) are assessed. The wurtzite phase core-multi-shell InP-InGaAs-InP nanowire QWs are characterised using cross-section transmission electron microscopy and photoluminescence measurements. The InP-InGaAs direct interface is found to be sharp while the InGaAs-InP inverted interface is more diffused, in agreement with their planar counterpart. Bright emission is observed from the single nanowires containing the QWs at room temperature, with no emission from the InP core or outer barrier. The tunability of the QW emission wavelength in the 1.3-1.55 μm communication wavelength range is demonstrated by varying the QW thickness and in the 1.3 μm range by varying the composition. The experiments are supported by simulation of the emission wavelength of the wurtzite phase InP-InGaAs QWs in the thickness range considered. The radial heterostructure is further extended to design multiple QWs with bright emission, therefore establishing the capability of this material system for nanowire based optical devices for communication applications.
High performance organic devices including polymer solar cells (PSCs) and light emitting diodes (PLEDs) were successfully demonstrated with the presence of highly ordered nanoimprinted Au nanodisks (Au NDs) in their solution-processed active/emissive layers, respectively. PSCs and PLEDs were fabricated using a low bandgap polymer and acceptor, nitrogen doped multiwalled carbon nanotubes poly[4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b']dithiophene-2,6-diyl][3-fluoro-2-[(2-ethylhexyl)carbonyl] thieno[3,4-b]-thiophenediyl] (n-MWCNTs:PTB7), and [6,6]-phenyl C71 butyric acid methyl ester (PC71BM) and (4,4-N,N-dicarbazole) biphenyl (CBP) doped with tris(2-phenylpyridine) iridium(iii) (Ir(ppy)3) as active/emissive layers, respectively. We synthesized nitrogen doped graphene and used it as anodic buffer layer in both devices. The localized surface plasmon resonance (LSPR) effect from Au NDs clearly contributed to the increase in light absorption/emission in the active layers from electromagnetic field enhancement, which originated from the excited LSPR in PSCs and PLEDs. In addition to the high density of LSPR and strong exciton-SP coupling, the electroluminescent (EL) enhancement is ascribed to enhanced spontaneous emission rates. This is due to the plasmonic near-field effect induced by Au NDs. The PSCs and PLEDs exhibited 14.98% (8.08% to 9.29%) under one sun of simulated air mass 1.5 global (AM1.5G) illumination (100 mW cm(-2)) and 19.18% (8.24 to 9.82 lm W(-1)) enhancement in the power conversion efficiencies (PCEs) compared to the control devices without Au NDs.
Solution processed zirconium acetylacetonate (Zr(acac)) is successfully employed as an electron extraction layer, replacing conventional titanium oxide, in planar CH3NH3PbI3 perovskite solar cells. The as-prepared Zr(acac) film possesses high transparency, high conductivity, a smooth morphology, high wettability, compatibility with PbI2 DMF solution, and an energy level matching that of CH3NH3PbI3 perovskite material. An average power conversion efficiency of about 11.93%, along with a high fill factor of 74.36%, an open circuit voltage of 1.03 V, and a short-circuit current density of 15.58 mA cm(-2) is achieved. The overall performance of the devices is slight better than that of cells using ruthenium acetylacetonate (Ru(acac)). The differences between solar cells with different electron extraction layers in charge recombination, charge transport and transfer and lifetime are further explored and it is demonstrate that Zr(acac) is a more effective and promising electron extraction layer. This work provides a simple, and cost effective route for the preparation of an effective hole extraction layer.
Theranostic nanoparticles hold promise for simultaneous imaging and therapy in colorectal cancer. Carcinoembryonic antigen can be used as a target for these nanoparticles because it is overexpressed in most colorectal cancers. Affimer reagents are synthetic proteins capable of binding specific targets, with additional advantages over antibodies for targeting. We fabricated silica nanoparticles using a water-in-oil microemulsion technique, loaded them with the photosensitiser Foslip, and functionalised the surface with anti-CEA Affimers to facilitate fluorescence imaging and photodynamic therapy of colorectal cancer. CEA-specific fluorescence imaging and phototoxicity were quantified in colorectal cancer cell lines and a LS174T murine xenograft colorectal cancer model. Anti-CEA targeted nanoparticles exhibited CEA-specific fluorescence in the LoVo, LS174T and HCT116 cell lines when compared to control particles (p < 0.0001). No toxicity was observed in LS174T cancer mouse xenografts or other organs. Following photo-irradiation, the anti-CEA targeted particles caused significant cell death in LoVo (60%), LS174T (90%) and HCT116 (70%) compared to controls (p < 0.0001). Photodynamic therapy (PDT) at 24 h in vivo showed a 4-fold reduction in tumour volume compared to control mouse xenografts (p < 0.0001). This study demonstrates the efficacy of targeted fluorescence imaging and PDT using Foslip nanoparticles conjugated to anti-CEA Affimer nanoparticles in in vitro and in vivo colorectal cancer models.
Zinc (Zn) is an excellent material for use as an anode for rechargeable batteries in water-based electrolytes. Nevertheless, the high activity of water leads to Zn corrosion and hydrogen evolution, along with the formation of dendrites on the Zn surface during repeated charge-discharge (CD) cycles. To protect the Zn anode and limit parasitic side reactions, an artificial solid electrolyte interphase (ASEI) protective layer is an effective strategy. Herein, an ASEI made of a covalent organic framework (COFs: HqTp and BpTp) was fabricated on the surface of a Zn anode via Schiff base reactions of aldehyde and amine linkers. It is seen that COFs can regulate the Zn-ion flux, resulting in dendritic-free Zn. COFs can also mitigate the formation of an irreversible passive layer and the hydrogen evolution reaction (HER). Zn plating/stripping tests using a symmetrical cell suggest that HqTpCOF@Zn shows superior stability and greater coulombic efficiency (CE) compared to bare Zn. The full cell having COFs@Zn also displays much improved cyclability. As a result, the COF proves to be a promising ASEI material to enhance the stability of the Zn anode in aqueous media.
The search for effective and non-invasive delivery modules to transport therapeutic molecules across skin has led to the discovery of a number of nanocarriers (viz.: liposomes, ethosomes, dendrimers, etc.) in the last few decades. However, available literature suggests that these delivery modules face several issues including poor stability, low encapsulation efficiency, and scale-up hurdles. Recently, carbon nanotubes (CNTs) emerged as a versatile tool to deliver therapeutics across skin. Superior stability, high loading capacity, well-developed synthesis protocol as well as ease of scale-up are some of the reason for growing interest in CNTs. CNTs have a unique physical architecture and a large surface area with unique surface chemistry that can be tailored for vivid biomedical applications. CNTs have been thus largely engaged in the development of transdermal systems such as tuneable hydrogels, programmable nonporous membranes, electroresponsive skin modalities, protein channel mimetic platforms, reverse iontophoresis, microneedles, and dermal buckypapers. In addition, CNTs were also employed in the development of RNA interference (RNAi) based therapeutics for correcting defective dermal genes. This review expounds the state-of-art synthesis methodologies, skin penetration mechanism, drug liberation profile, loading potential, characterization techniques, and transdermal applications along with a summary on patent/regulatory status and future scope of CNT based skin therapeutics.
The design of DNA nanotubes is a promising and hot research branch in structural DNA nanotechnology, which is rapidly developing as a versatile method for achieving subtle nanometer scale materials and molecular diagnostic/curative devices. Multifarious methods have been proposed to achieve varied DNA nanotubes, such as using square tiles and single-stranded tiles, but it is still a challenge to develop a bottom-up assembly way to build DNA nanotubes with different diameters and patterns using certain universal DNA nanostructures. This work addresses the challenge by assembling three types of spatial DNA nanotubes with different diameters and patterns from the so-called "basic bricks", i.e., hierarchical DNA sub-tiles. A high processing rate and throughput synthesis of DNA nanotubes are observed and analyzed by atomic force microscopy. Experimental observations and data analysis suggests the stability and controllability of DNA nanotubes assembled by hierarchical DNA sub-tiles.
Successful application of a magnetophoretic separation technique for harvesting biological cells often relies on the need to tag the cells with magnetic nanoparticles. This study investigates the underlying principle behind the attachment of iron oxide nanoparticles (IONPs) onto microalgal cells, Chlorella sp. and Nannochloropsis sp., in both freshwater and seawater, by taking into account the contributions of various colloidal forces involved. The complex interplay between van der Waals (vdW), electrostatic (ES) and Lewis acid-base interactions (AB) in dictating IONP attachment was studied under the framework of extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) analysis. Our results showed that ES interaction plays an important role in determining the net interaction between the Chlorella sp. cells and IONPs in freshwater, while the AB and vdW interactions play a more dominant role in dictating the net particle-to-cell interaction in high ionic strength media (≥100 mM NaCl), such as seawater. XDLVO predicted effective attachment between cells and surface functionalized IONPs (SF-IONPs) with an estimated secondary minimum of -3.12 kT in freshwater. This prediction is in accordance with the experimental observation in which 98.89% of cells can be magnetophoretically separated from freshwater with SF-IONPs. We have observed successful magnetophoretic separation of microalgal cells from freshwater and/or seawater for all the cases as long as XDLVO analysis predicts particle attachment. For both the conditions, no pH adjustment is required for particle-to-cell attachment.
Neurodegenerative disorder is an illness involving neural dysfunction/death attributed to complex pathological processes, which eventually lead to the mortality of the host. It is generally recognized through features such as mitochondrial dysfunction, protein aggregation, oxidative stress, metal ions dyshomeostasis, membrane potential change, neuroinflammation and neurotransmitter impairment. The aforementioned neuronal dysregulations result in the formation of a complex neurodegenerative microenvironment (NME), and may interact with each other, hindering the performance of therapeutics for neurodegenerative disease (ND). Recently, smart nanoassemblies prepared from functional nanoparticles, which possess the ability to interfere with different NME factors, have shown great promise to enhance the diagnostic and therapeutic efficacy of NDs. Herein, this review highlights the recent advances of stimuli-responsive nanoassemblies that can effectively combat the NME for the management of ND. The first section outlined the NME properties and their interrelations that are exploitable for nanoscale targeting. The discussion is then extended to the controlled assembly of functional nanoparticles for the construction of stimuli-responsive nanoassemblies. Further, the applications of stimuli-responsive nanoassemblies for the enhanced diagnosis and therapy of ND are introduced. Finally, perspectives on the future development of NME-tailored nanomedicines are given.
Heterojunction photocatalysts have shown their immense capability in enhancing photogenerated charge carrier separation. Yet, the intrinsic scarcity of active sites in semiconductor components of heterojunction photocatalysts limits their potential for photocatalysis being used in practical applications. Herein, we employ a non-noble metal cocatalyst (i.e., NiS) for modulating a S-scheme heterojunction photocatalyst consisting of Cd3(C3N3S3)2 (CdCNS) and CdS. It is revealed that the formation of the CdCNS/CdS S-scheme heterojunction can enable optimal photogenerated charge carrier utilization efficiency and optimized redox capability. More importantly, the meticulous loading of NiS can play multiple roles in enhancing the photocatalytic performance of the CdCNS/CdS photocatalyst, including endowing it with abundant surface-active sites and acting as a photogenerated electron acceptor. As a result, the optimized NiS-loaded CdCNS/CdS attains an excellent hydrogen production rate of 38.17 mmol g-1 h-1, to reach a quantum efficiency of 29.02% at 420 nm. The results reported in this work provide an interesting insight into the important roles of surface-active site modulation in optimizing photocatalytic performances.
We report the self-assembly of an extensive inter-ligand hydrogen-bonding network of octylphosphonates on the surface of cesium lead bromide nanocrystals (CsPbBr3 NCs). The post-synthetic addition of octylphosphonic acid to oleic acid/oleylamine-capped CsPbBr3 NCs promoted the attachment of octylphosphonate to the NC surface, while the remaining oleylammonium ligands maintained the high dispersability of the NCs in non-polar solvent. Through powerful 2D solid-state 31P-1H NMR, we demonstrated that an ethyl acetate/acetonitrile purification regime was crucial for initiating the self-assembly of extensive octylphosphonate chains. Octylphosphonate ligands were found to preferentially bind in a monodentate mode through P-O-, leaving polar P[double bond, length as m-dash]O and P-OH groups free to form inter-ligand hydrogen bonds. The octylphosphonate ligand network strongly passivated the nanocrystal surface, yielding a fully-purified CsPbBr3 NC ink with PLQY of 62%, over 3 times higher than untreated NCs. We translated this to LED devices, achieving maximum external quantum efficiency and luminance of 7.74% and 1022 cd m-2 with OPA treatment, as opposed to 3.59% and 229 cd m-2 for untreated CsPbBr3 NCs. This represents one of the highest efficiency LEDs obtained for all-inorganic CsPbBr3 NCs, accomplished through simple, effective passivation and purification processes. The robust binding of octylphosphonates to the perovskite lattice, and specifically their ability to interlink through hydrogen bonding, offers a promising passivation approach which could potentially be beneficial across a breadth of halide perovskite optoelectronic applications.
The transformation of systematic vacuum and hydrogen annealing effects in graphene devices on the SiO2 surface is reported based on experimental and van der Waals interaction corrected density functional theory (DFT) simulation results. Vacuum annealing removes p-type dopants and reduces charged impurity scattering in graphene. Moreover, it induces n-type doping into graphene, leading to the improvement of the electron mobility and conductivity in the electron transport regime, which are reversed by exposing to atmospheric environment. On the other hand, annealing in hydrogen/argon gas results in smaller n-type doping along with a decrease in the overall conductivity and carrier mobility. This degradation of the conductivity is irreversible even the graphene devices are exposed to ambience. This was clarified by DFT simulations: initially, silicon dangling bonds were partially terminated by hydrogen, subsequently, the remaining dangling bonds became active and the distance between the graphene and SiO2 surface decreased. Moreover, both annealing methods affect the graphene channel including the vicinity of the metal contacts, which plays an important role in asymmetric carrier transport.