Two-dimensional materials have attracted intensive attention recently due to their unique optical and electronic properties and their promising applications in water splitting and solar cells. As a representative layer-structured of transition metal dichalcogenides, MoS2has attracted considerable devotion owing to its exceptional photo and electro properties. Here, we show that the chemical vapour deposition (CVD) growth of MoS2on Si photocathode and graphene/Si photocathode can be used to prepare photoelectrocatalysts for water splitting. We explore a bottom-up method to grow vertical heterostructures of MoS2and graphene by using the two-step CVD. Graphene is first grown through ambient-pressure CVD on a Cu substrate and then transferred onto SiO2/Si substrate by using the chemical wet transfer followed by the second CVD method to grow MoS2over the graphene/SiO2/Si. The effect of the growth temperatures of MoS2is studied, and the optimum temperature is 800 °C. The MoS2produced at 800 °C has the highest photocurrent density at -0.23 mA cm-2in 0.5 M Na2SO4and -0.51 mA cm-2in 0.5 M H2SO4at -0.8 V vs. Ag/AgCl. The linear sweep voltammetry shows that MoS2in 0.5 M H2SO4has about 55% higher photocurrent density than MoS2in Na2SO4due to the higher protons (H+) in the H2SO4electrolyte solution, which are sufficiently charged to reduce to H2and, therefore hydrogen evolves more rapidly where the photocurrent density and hydrogen generation can be enhanced. MoS2/graphene/SiO2/Si (MGS) has -0.07 mA cm-2at -0.8 V vs. Ag/AgCl of photocurrent density, which is 70% lower than that of bare MoS2because MGS is thicker compared with MoS2. Thus, MoS2has potential as a photocatalyst in photoelectrochemical water splitting. The structure and the morphology of MoS2play an important role in determining the photocurrent performance.
Upconversion (UC) of lanthanide-doped nanostructure has the unique ability to convert low energy infrared (IR) light to high energy photons, which has significant potential for energy conversion applications. This review concisely discusses the basic concepts and fundamental theories of lanthanide nanostructures, synthesis techniques, and enhancement methods of upconversion for photovoltaic and for near-infrared (NIR) photodetector (PD) application. In addition, a few examples of lanthanide-doped nanostructures with improved performance were discussed, with particular emphasis on upconversion emission enhancement using coupling plasmon. The use of UC materials has been shown to significantly improve the NIR light-harvesting properties of photovoltaic devices and photocatalytic materials. However, the inefficiency of UC emission also prompted the need for additional modification of the optical properties of UC material. This improvement entailed the proper selection of the host matrix and optimization of the sensitizer and activator concentrations, followed by subjecting the UC material to surface-passivation, plasmonic enhancement, or doping. As expected, improving the optical properties of UC materials can lead to enhanced efficiency of PDs and photovoltaic devices.
Metal sulfides are promising anode materials for lithium ion batteries because of the high specific capacities and better electrochemical kinetics comparing to their oxide counterparts. In this paper, novel monocrystalline wurtzite ZnS@N-doped carbon (ZnS@N-C) nanoplates, whose morphology and phase are different from the common ZnS particles with cubic phase, are successfully synthesized. The ZnS@N-C nanoplates exhibit long cycle life with a high reversible specific capacity of 536.8 mAh · g-1after 500 cycles at a current density of 500 mA · g-1, which is superior to the pure ZnS nanoplates, illustrating the obvious effect of the N-doped carbon coating for mitigating volume change of the ZnS nanoplates and enhancing the electronic conductivity during charge/discharge processes. Furthermore, it is revealed that the ZnS single crystals with wurtzite phase in the ZnS@N-C nanoplates are transformed to the polycrystalline cubic phase ZnS after charge/discharge processes. In particular, the ZnS@N-C nanoplates are combined with the commercial LiNi0.6Co0.2Mn0.2O2cathode to fabricate a new type of LiNi0.6Co0.2Mn0.2O2/ZnS@N-C complete battery, which exhibits good cycling durability up to 120 cycles at a charge/discharge rate of 1 C after the prelithiation treatment on the ZnS@N-C anode, highlighting the potential of the ZnS@N-C nanoplates anode material applied in lithium ion battery.
The length of titania nanotubes formed by anodization of 0.1 mm thick titanium foil was found to be a strong function of the pH of the electrolyte. The longest nanotubes were formed by using an electrolyte consisting of 1 M Na(2)SO(4) plus 5 wt% NH(4)F with pH 7. At this pH, after 30 min of anodization, 3 microm length nanotubular titania arrays with top diameters of approximately 50 nm and bottom diameters of 100 nm were produced. No acid was added to this electrolyte. The formation of titania nanotubes in neutral pH systems was therefore successful due to the excess NH(4)F in the electrolyte which increases the chemical dissolution process at the metal/oxide interface. Since the pH of the electrolyte at the top part of the nanotubes is kept very high, the dissolution of the nanotubes at the surface is minimal. However, the amount is adequate to remove the initial barrier layer, forming a rather well-defined nanoporous structure. All anodized foils were weakly crystalline and the transformation to anatase phase was achieved by heat treatment at temperatures from 200 to 500 degrees C for 1 h in air. Annealing at temperatures above 500 degrees C induce rutile phase formation and annealing at higher temperatures accelerates the diffusion of Ti(4+) leading to excessive growth and the nanotubular structure diminishes.
This study describes the properties of colloidal gold nanoparticles (AuNPs) with sizes of 20, 30 and 40 nm, which were synthesized using citrate reduction or seeding-growth methods. Likewise, the conjugation of these AuNPs to mouse anti-human IgG(4) (MαHIgG(4)) was evaluated for an immunochromatographic (ICG) strip test to detect brugian filariasis. The morphology of the AuNPs was studied based on the degree of ellipticity (G) of the transmission electron microscopy images. The AuNPs produced using the seeding-growth method showed lower ellipticity (G ≤ 1.11) as compared with the AuNPs synthesized using the citrate reduction method (G ≤ 1.18). Zetasizer analysis showed that the AuNPs that were synthesized using the seeding-growth method were almost monodispersed with a lower polydispersity index (PDI; PDI≤0.079), as compared with the AuNPs synthesized using the citrate reduction method (PDI≤0.177). UV-visible spectroscopic analysis showed a red-shift of the absorbance spectra after the reaction with MαHIgG(4), which indicated that the AuNPs were successfully conjugated. The optimum concentration of the BmR1 recombinant antigen that was immobilized on the surface of the ICG strip on the test line was 1.0 mg ml(-1). When used with the ICG test strip assay and brugian filariasis serum samples, the conjugated AuNPs-MαHIgG(4) synthesized using the seeding-growth method had faster detection times, as compared with the AuNPs synthesized using the citrate reduction method. The 30 nm AuNPs-MαHIgG(4), with an optical density of 4 from the seeding-growth method, demonstrated the best performance for labelling ICG strips because it displayed the best sensitivity and the highest specificity when tested with serum samples from brugian filariasis patients and controls.
A stable, biocompatible and exquisite SPIONs-PEG-HER targeting complex was developed. Initially synthesized superparamagnetic iron oxide nanoparticles (SPIONs) were silanized using 3-aminopropyltrimethoxysilane (APS) as the coupling agent in order to allow the covalent bonding of polyethylene glycol (PEG) to the SPIONs to improve the biocompatibility of the SPIONs. SPIONs-PEG were then conjugated with herceptin (HER) to permit the SPIONs-PEG-HER to target the specific receptors expressed over the surface of the HER2+ metastatic breast cancer cells. Each preparation step was physico-chemically analyzed and characterized by a number of analytical methods including AAS, FTIR spectroscopy, XRD, FESEM, TEM, DLS and VSM. The biocompatibility of SPIONs-PEG-HER was evaluated in vitro on HSF-1184 (human skin fibroblast cells), SK-BR-3 (human breast cancer cells, HER+), MDA-MB-231 (human breast cancer cells, HER-) and MDA-MB-468 (human breast cancer cells, HER-) cell lines by performing MTT and trypan blue assays. The hemolysis analysis results of the SPIONs-PEG-HER and SPIONs-PEG did not indicate any sign of lysis while in contact with erythrocytes. Additionally, there were no morphological changes seen in RBCs after incubation with SPIONs-PEG-HER and SPIONs-PEG under a light microscope. The qualitative and quantitative in vitro targeting studies confirmed the high level of SPION-PEG-HER binding to SK-BR-3 (HER2+ metastatic breast cancer cells). Thus, the results reflected that the SPIONs-PEG-HER can be chosen as a favorable biomaterial for biomedical applications, chiefly magnetic hyperthermia, in the future.
This study introduces a new class of heat transfer fluids by dispersing functionalised graphene oxide nanoparticles (GNPs) in ammonium and phosphonium-based deep eutectic solvents (DESs) without the aid of a surfactant. Different molar ratios of salts and hydrogen bond donors (HBD) were used to synthesise DESs for the preparation of different concentrations of graphene nanofluids (GNFs). The concentrations of GNPs were 0.01 wt%, 0.02 wt% and 0.05 wt %. Homogeneous and stable suspensions of nanofluids were obtained by high speed homogenisation and an ultrasonication process. The stability of the GNFs was determined through visual observation for 4 weeks followed by a centrifugal process (5000-20,000 rpm) for 30 min in addition to zeta potential studies. Dispersion of the GNPs in DES was observed using an optical microscope. The synthesised DES-based GNFs showed no particle agglomeration and formation of sediments in the nanofluids. Thermo-physical properties such as thermal conductivity and specific heat of the nanofluids were also investigated in this research. The highest thermal conductivity enhancement of 177% was observed. The findings of this research provide a new class of engineered fluid for heat transfer applications as a function of temperature, type and composition DESs as well as the GNPs concentration.
Visible-light-active freestanding zirconia (ZrO2) nanotube (FSZNT) arrays were fabricated by a facile electrochemical anodization method in fluoride containing ethylene glycol electrolyte added to it was 1 vol% of potassium carbonate (K2CO3) at 60 V for 1 h. Poor adhesion at the metal∣oxide interface was induced by K2CO3 leading to the formation of FSZNT flakes. The effect of the crystal structures of the FSZNTs e.g., amorphous, amorphous/tetragonal, and tetragonal/monoclinic was investigated towards the photocatalytic reduction of 10 ppm hexavalent chromium, Cr(VI) at pH 2 under sunlight. The results demonstrate the amorphous FSZNTs exhibited the highest Cr(VI) removal efficiency than the crystalline FSZNTs (95% versus 33% after 5 h). The high photocatalytic activity of the amorphous FSZNTs can be attributed to enhanced Cr(VI) adsorption, high visible light absorption, and better charge carrier separation. The low photocatalytic activity of the crystalline FSZNTs annealed at 500 °C was mainly attributed to poor Cr(VI) adsorption, low visible light absorption, and less photoactive monoclinic-ZrO2.
The delivery of a full plasmid, encoding the green fluorescent protein gene into African monkey kidney (Vero3) cells, was successfully achieved using nanobiocomposites based on layered double hydroxides. This demonstrated the potential of using the system as an alternative DNA delivery vector. Intercalation of the circular plasmid DNA, pEGFP-N2, into Mg/Al-NO(3)(-) layered double hydroxides (LDH) was accomplished through anion exchange routes to form the nanobiocomposite material. The host was previously synthesized at the Mg(2+) to Al(3+) molar ratio R(i) = 2 and subsequently intercalated with plasmid DNA. Size expansion of the interlamellae host from 8.8 A in LDH to 42 A was observed in the resulting nanobiocomposite, indicating stable hybridization of the plasmid DNA. The powder x-ray diffraction (PXRD) results, supplemented with Fourier-transform infrared (FTIR) spectroscopy, compositional and electrophoresis studies confirmed the encapsulation episode of the biomaterial. In order to elucidate the use of this resulting nanobiocomposite as a delivery vector, an MTT assay was performed to determine any cytotoxic effects of the host towards cells. The intercalated pEGFP-N2 anion was later successfully recovered through acidification with HNO(3) after treatment with DNA-degrading enzymes, thus also showing the ability of the LDH host to protect the intercalated biomaterial from degradation. Cell transfection studies on Vero3 cells were then performed, where cells transfected with the nanobiocomposite exhibited fluorescence as early as 12 h post-treatment compared to naked delivery of the plasmid itself.
An ethanol gas sensor with enhanced sensor response was fabricated using Ni-doped SnO2 nanorods, synthesized via a simple hydrothermal method. It was found that the response (R = R 0/R g) of a 5.0 mol% Ni-doped SnO2 (5.0Ni:SnO2) nanorod sensor was 1.4 × 104 for 1000 ppm C2H5OH gas, which is about 13 times higher than that of pure SnO2 nanorods, (1.1 × 103) at the operating temperature of 450 °C. Moreover, for 50 ppm C2H5OH gas, the 5.0Ni:SnO2 nanorod sensor still recorded a significant response reading, namely 2.0 × 103 with a response time of 30 s and recovery time of 10 min. To investigate the effect of Ni dopant (0.5-5.0 mol%) on SnO2 nanorods, structural characterizations were demonstrated using field emission scanning electron microscopy, high-resolution transmission electron microscopy, Fourier transform infrared spectroscopy, x-ray diffraction (XRD) analysis, x-ray photoelectron spectroscopy and an ultraviolet-visible spectrometer. XRD results confirmed that all the samples consisted of tetragonal-shaped rutile SnO2 nanorods. It was found that the average diameter and length of the nanorods formed in 5.0Ni:SnO2 were four times smaller (∼6 and ∼35 nm, respectively) than those of the nanorods formed in pure SnO2 (∼25 and 150 nm). Interestingly, both samples had the same aspect ratio, ∼6. It is proposed that the high response of the 5.0Ni:SnO2 nanorod sensor can be attributed to the particle size, which causes an increase in the thickness of the charge depletion layer, and the presence of oxygen vacancies within the matrix of SnO2 nanorods.
To synthesize lithium ferrite with various Gd concentrations (Li0.5Fe2.5-xGdxO4), x = 0.00, 0.025, 0.05, 0.075, 0.1, solutes were dissolved in glycol, i.e. by using the without water and surfactant (WOWS) sol-gel method. X-ray diffraction (XRD) analysis confirmed that the material possessed an inverse spinel cubic structure and is single phase. Pellets of all samples were sintered at 700 °C and XRD confirmed that samples were crystalline, phase pure and had an inverse spinel cubic lattice. Scanning electron microscopy indicated that the grains were agglomerated and had a predominantly spherical shape. It is concluded that Gd acts as a grain refiner in lithium ferrite up to a Gd concentration of 0.05. AC conductivity and dielectric constant increased by increasing Gd concentration. The Maxwell-Wagner model and Johnsher's power law were used to explain the dielectric properties. DC conductivity was measured from 100 to 600 °C. DC conductivity was explained by the hopping mechanism. It is concluded that DC resistivity and dielectric constant values are related reciprocally in the prepared sample. AC electrical properties were also measured at a constant frequency of 1 MHz in the temperature range from 400 to 600 °C. Gd-substituted lithium ferrite showed high AC conductivity, high DC resistivity and constant dielectric values, but low dielectric loss values as compared to pure lithium ferrite.
The past few years have witnessed remarkable progress in solution-processed methylammonium lead halide (CH3NH3PbX3, X = halide) perovskite solar cells (PSCs) with reported photoconversion efficiency (η) exceeding 20% in laboratory-scale devices and reaching up to 13% in their large area perovskite solar modules (PSMs). These devices mostly employ mesoporous TiO2 nanoparticles (NPs) as an electron transport layer (ETL) which provides a scaffold on which the perovskite semiconductor can grow. However, limitations exist which are due to trap-limited electron transport and non-complete pore filling. Herein, we have employed TiO2 nanorods (NRs), a material offering a two-fold higher electronic mobility and higher pore-filing compared to their particle analogues, as an ETL. A crucial issue in NRs' patterning over substrates is resolved by using precise Nd:YVO4 laser ablation, and a champion device with η ∼ 8.1% is reported via a simple and low cost vacuum-vapor assisted sequential processing (V-VASP) of a CH3NH3PbI3 film. Our experiments showed a successful demonstration of NRs-based PSMs via the V-VASP technique which can be applied to fabricate large area modules with a pin-hole free, smooth and dense perovskite layer which is required to build high efficiency devices.
The estimation of nanoparticle number concentration in colloidal suspensions is a prerequisite in many procedures, and in particular in multi-stage, low-yield reactions. Here, we describe a rapid, non-destructive method based on optical extinction and dynamic light scattering, which combines measurements using common bench-top instrumentation with a numerical algorithm to calculate the particle size distribution and concentration. These quantities were derived from Mie theory applied to measurements of the optical extinction spectrum of homogeneous, non-absorbing nanoparticles, and the relative particle size distribution of a colloidal suspension. The work presents an approach to account for particle size distributions achieved by dynamic light scattering which, due to the underlying model, may not be representative of the true sample particle size distribution. The presented approach estimates the absolute particle number concentration of samples with mono-, bi-modal and broad size distributions with <50% precision. This provides a convenient and practical solution for number concentration estimation required during many applications of colloidal nanomaterials.
In this research, novel ultrafiltration nanocomposite membranes were prepared by incorporating self-synthesized nanoporous titanium dioxide (NTiO2) nanoparticles into polysulfone. The surface of the nanoparticle was treated with a silane-based modifier to improve its distribution in the host polymer. Atomic-force microscopy, scanning electron microscopy, Fourier transform infrared spectroscopy, Brunauer-Emmett-Teller, transmission electron microscopy, energy-dispersive x-ray spectroscopy, porosity and contact angle tests were conducted to characterize the properties of the particles as well as the fabricated nanocomposite membranes. The effects of the nanoparticle incorporation were evaluated by conducting ultrafiltration experiments. It was reported that the membrane pure water flux was increased with increasing NTiO2 loading owing to the high porosity of the nanoparticles embedded and/or formation of enlarged pores upon addition of them. The antifouling capacity of the membranes was also tested by ultrafiltration of bovine serum albumin fouling solution. It was found that both water flux and antifouling capacity tended to reach desired level if the NTiO2 added was at optimized loading.
ZrO2 nanotubes (ZrNTs) were produced by anodisation of zirconium foil in H2O2/NH4F/ethylene glycol electrolyte. The as-anodised foils were then soaked in the anodising electrolyte for 12 h. Soaking weakens the adherence of the anodic layer from the substrate resulting in freestanding ZrNTs (FS-ZrNTs). Moreover, the presence of H2O2 in the electrolyte also aids in weakening the adhesion of the film from the foil, as foil anodised in electrolyte without H2O2 has good film adherence. The as-anodised FS-ZrNTs film was amorphous and crystallised to predominantly tetragonal phase upon annealing at >300 °C. Annealing must, however, be done at <500 °C to avoid monoclinic ZrO2 formation and nanotubes disintegration. FS-ZrNTs annealed at 450 °C exhibited the highest photocatalytic ability to degrade methyl orange (MO), whereby 82% MO degradation was observed after 5 h, whereas FS-ZrNTs with a mixture of monoclinic and tetragonal degraded 70% of MO after 5 h.
Nanostructured metal oxide semiconductors have emerged as promising nanoscale photocatalysts due to their excellent photosensitivity, chemical stability, non-toxicity, and biocompatibility. Enhancing the photocatalytic activity of metal oxide is critical in improving their efficiency in radical ion production upon optical exposure for various applications. Therefore, this review paper provides an in-depth analysis of the photocatalytic activity of nanostructured metal oxides, including the photocatalytic mechanism, factors affecting the photocatalytic efficiency, and approaches taken to boost the photocatalytic performance through structure or material modifications. This paper also highlights an overview of the recent applications and discusses the recent advancement of ZnO-based nanocomposite as a promising photocatalytic material for environmental remediation, energy conversion, and biomedical applications.
The present study aims at engineering, fabrication, characterization, and qualifications of papain (PPN) conjugated SiO2-coated iron oxide nanoparticles 'IONPs@SiO2-PPN'. Initially fabricated iron oxide nanoparticles (IONPs) were coated with silica (SiO2) using sol-gel method to hinder the aggregation and to enhance biocompatibility. Next, PPN was loaded as an anticancer agent into the silica coated IONPs (IONPs@SiO2) for the delivery of papain to the HeLa cancer cells. This fabricated silica-coated based magnetic nanoparticle is introduced as a new physiologically-compatible and stable drug delivery vehicle for delivering of PPN to the HeLa cancer cell line. The IONPs@SiO2-PPN were characterized using FT-IR, AAS, FESEM, XRD, DLS, and VSM equipment. Silica was amended on the surface of iron oxide nanoparticles (IONPs, γ-Fe2O3) to modify its biocompatibility and stability. The solvent evaporation method was used to activate PPN vectorization. The following tests were performed to highlight the compatibility of our proposed delivery vehicle: in vitro toxicity assay, in vivo acute systemic toxicity test, and the histology examination. The results demonstrated that IONPs@SiO2-PPN successfully reduced the IC50 values compared with the native PPN. Also, the structural alternations of HeLa cells exposed to IONPs@SiO2-PPN exhibited higher typical hallmarks of apoptosis compared to the cells treated with the native PPN. The in vivo acute toxicity test indicated no clinical signs of distress/discomfort or weight loss in Balb/C mice a week after the intravenous injection of IONPs@SiO2 (10 mg kg-1). Besides, the tissues architectures were not affected and the pathological inflammatory alternations detection failed. In conclusion, IONPs@SiO2-PPN can be chosen as a potent candidate for further medical applications in the future, for instance as a drug delivery vehicle or hyperthermia agent.
Mesoporous TiO2 hollow spheres nanostructures with high surface areas were successfully prepared using a microwave method. The prepared hollow spheres have a size range between 200 and 500 nm. The spheres consisted of numerous smaller TiO2 nanoparticles with an average diameter of 8 nm. The particles had an essentially mesoporous structure with a pore size in the range of 2-50 nm. The results confirmed that the synthesised of anatase TiO2 nanoparticles with specific surface area approximately 172.3 m2/g. The effect of ultra violet and visible light irradiation and catalyst dosage on the TiO2 photocatalytic activity was studied by measuring the degradation rate of methylene blue. The maximum dye degradation performances with low amount catalyst loading (30 mg) were 99 % and 63.4 % using the same duration of ultra violet and visible light irradiation, respectively (120 min).
The customization of hybrid nanofluids to achieve a particular and controlled growth rate of thermal transport is done to meet the needs of applications in heating and cooling systems, aerospace and automotive industries, etc. Due to the extensive applications, the aim of the current paper is to derive a numerical solution to a wall jet flow problem through a stretching surface. To study the flow problem, authors have considered a non-Newtonian Eyring-Powell hybrid nanofluid with water and CoFe2O4and TiO2nanoparticles. Furthermore, the impact of a magnetic field and irregular heat sink/source are studied. To comply with the applications of the wall jet flow, the authors have presented the numerical solution for two cases; with and without a magnetic field. The numerical solution is derived with a similarity transformation and MATLAB-based bvp4c solver. The value of skin friction for wall jet flow at the surface decreases by more than 50% when the magnetic fieldMA=0.2is present. The stream function value is higher for the wall jet flow without the magnetic field. The temperature of the flow rises with the dominant strength of the heat source parameters. The results of this investigation will be beneficial to various applications that utilize the applications of a wall jet, such as in car defrosters, spray paint drying for vehicles or houses, cooling structures for the CPU of high-processor laptops, sluice gate flows, and cooling jets over turbo-machinery components, etc.
We used 40 ± 5 nm gold nanoparticles (GNPs) as colorimetric sensor to visually detect swine-specific conserved sequence and nucleotide mismatch in PCR-amplified and non-amplified mitochondrial DNA mixtures to authenticate species. Colloidal GNPs changed color from pinkish-red to gray-purple in 2 mM PBS. Visually observed results were clearly reflected by the dramatic reduction of surface plasmon resonance peak at 530 nm and the appearance of new features in the 620-800 nm regions in their absorption spectra. The particles were stabilized against salt-induced aggregation upon the adsorption of single-stranded DNA. The PCR products, without any additional processing, were hybridized with a 17-base probe prior to exposure to GNPs. At a critical annealing temperature (55 °C) that differentiated matched and mismatched base pairing, the probe was hybridized to pig PCR product and dehybridized from the deer product. The dehybridized probe stuck to GNPs to prevent them from salt-induced aggregation and retained their characteristic red color. Hybridization of a 27-nucleotide probe to swine mitochondrial DNA identified them in pork-venison, pork-shad and venison-shad binary admixtures, eliminating the need of PCR amplification. Thus the assay was applied to authenticate species both in PCR-amplified and non-amplified heterogeneous biological samples. The results were determined visually and validated by absorption spectroscopy. The entire assay (hybridization plus visual detection) was performed in less than 10 min. The LOD (for genomic DNA) of the assay was 6 µg ml(-1) swine DNA in mixed meat samples. We believe the assay can be applied for species assignment in food analysis, mismatch detection in genetic screening and homology studies between closely related species.