Displaying publications 1 - 20 of 126 in total

Abstract:
Sort:
  1. Agi A, Junin R, Alqatta AYM, Gbadamosi A, Yahya A, Abbas A
    Ultrason Sonochem, 2019 Mar;51:214-222.
    PMID: 30401623 DOI: 10.1016/j.ultsonch.2018.10.023
    Ultrafiltration has been proven to be very effective in the treatment of oil-in-water emulsions, since no chemical additives are required. However, ultrafiltration has its limitations, the main limits are concentration polarization resulting to permeate flux decline with time. Adsorption, accumulation of oil and particles on the membrane surface which causes fouling of the membrane. Studies have shown that the ultrasonic is effective in cleaning of fouled membrane and enhancing membrane filtration performance. But the effectiveness also, depends on the selection of appropriate membrane material, membrane geometry, ultrasonic module design, operational and processing condition. In this study, a hollow and flat-sheet polyurethane (PU) membranes synthesized with different additives and solvent were used and their performance evaluated with oil-in-water emulsion. The steady-state permeate flux and the rejection of oil in percentage (%) at two different modes were determined. A dry/wet spinning technique was used to fabricate the flat-sheet and hollow fibre membrane (HFMs) using Polyethersulfone (PES) polymer base, Polyvinylpyrrolidone (PVP) additive and N, N-Dimethylacetamide (DMAc) solvent. Ultrasonic assisted cross-flow ultrafiltration module was built to avoid loss of ultrasonic to the surrounding. The polyurethane (PU) was synthesized by polymerization and sulphonation to have an anionic group (-OH; -COOH; and -SO3H) on the membrane surface. Changes in morphological properties of the membrane had a significant effect on the permeate flow rate and oil removal. Generation of cavitation and Brownian motion by the ultrasonic were the dominant mechanisms responsible for ultrafiltration by cracking the cake layers and reducing concentration polarization at the membrane surface. The percentage of oil after ultrafiltration process with ultrasonic is about 90% compared to 49% without ultrasonic. Ultrasonic is effective in enhancing the membrane permeate flux and controlling membrane fouling.
  2. Sodipo BK, Abdul Aziz A
    Ultrason Sonochem, 2015 Mar;23:354-9.
    PMID: 25315418 DOI: 10.1016/j.ultsonch.2014.09.011
    A non-seeded method of incorporating superparamagnetic iron oxide nanoparticles (SPION) into silica nanoparticles is presented. Mixture of both SPION and silica nanoparticles was ultrasonically irradiated. The collapsed bubbles and shockwave generated from the ultrasonic irradiation produce tremendous force that caused inelastic collision and incorporation of SPION into the silica. Physicochemical analyses using transmission electron microscope (TEM), electronic spectroscopic imaging (ESI), X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy demonstrated the formation of SPION/silica composite nanoparticles. The prepared composite nanoparticles exhibited superparamagnetic behaviour and nearly 70% of the initial saturation magnetization (Ms) of the SPION was retained. The presence and reactivity of the silica were demonstrated via assembling decanethiol monolayer on the composite nanoparticles. The silanol group of the silica provided the binding site for the alkyl group in the decanethiol molecules. Therefore, the thiol moiety became the terminal and functional group on the magnetic composite nanoparticles.
  3. Pang YL, Abdullah AZ
    Ultrason Sonochem, 2012 May;19(3):642-51.
    PMID: 22000097 DOI: 10.1016/j.ultsonch.2011.09.007
    Sonocatalytic degradation of various organic dyes (Congo Red, Reactive Blue 4, Methyl Orange, Rhodamine B and Methylene Blue) catalyzed by powder and nanotubes TiO(2) was studied. Both catalysts were characterized using transmission electron microscope (TEM), surface analyzer, Raman spectroscope and thermal gravimetric analyzer (TGA). Sonocatalytic activity of powder and nanotubes TiO(2) was elucidated based on the degradation of various organic dyes. The former catalyst was favorable for treatment of anionic dyes, while the latter was more beneficial for cationic dyes. Sonocatalytic activity of TiO(2) nanotubes could be up to four times as compared to TiO(2) powder under an ultrasonic power of 100 W and a frequency of 42 kHz. This was associated with the higher surface area and the electrostatic attraction between dye molecules and TiO(2) nanotubes. Fourier transform-infrared spectrometer (FT-IR) was used to identify changes that occurred on the functional group in Rhodamine B molecules and TiO(2) nanotubes after the reaction. Sonocatalytic degradation of Rhodamine B by TiO(2) nanotubes apparently followed the Langmuir-Hinshelwood adsorption kinetic model with surface reaction rate of 1.75 mg/L min. TiO(2) nanotubes were proven for their high potential to be applied in sonocatalytic degradation of organic dyes.
  4. Jamalluddin NA, Abdullah AZ
    Ultrason Sonochem, 2011 Mar;18(2):669-78.
    PMID: 20933452 DOI: 10.1016/j.ultsonch.2010.09.004
    The development of Fe(III)/TiO(2) catalysts for sonocatalytic degradation of Reactive Blue 4 (RB4) dye in water was carried out using sol-gel method. Their surface morphology, phase transformation and surface characteristics were studied using SEM, XRD and surface analyzer, respectively. Phase transformation from amorphous to anatase occurred at 500°C and transformation of anatase to rutile phase occurred at 700°C. Complete rutile phase was formed at 900°C with corresponding increase in the particle size. Increasing in Fe(III) loading led to a reduction in the anatase phase and with the formation of weaker and broader of diffraction peaks. Surface morphology of the prepared catalyst was clearly observed with increasing calcination temperature. Surface area of the prepared catalyst decreased with increasing calcination temperature or increasing Fe(III) loading. The combination of 0.4 mol% of Fe(III)/TiO(2) with ultrasonic irradiation gave the highest sonocatalytic activity in the removal of RB4 from the aqueous solution. On the other hand, the presence of even small amount of rutile inhibited the catalytic activity of catalyst. 1.5 g/L was the optimum amount of catalyst that led to the highest sonocatalytic degradation of RB4 with an efficiency of 90%. Aeration significantly accelerated the reaction rate. Higher removal at 96% could be achieved with the combination of 0.4Fe(III)/TiO(2) and aeration under ultrasonic irradiation.
  5. Sukor NF, Jusoh R, Kamarudin NS, Abdul Halim NA, Sulaiman AZ, Abdullah SB
    Ultrason Sonochem, 2020 Apr;62:104876.
    PMID: 31796331 DOI: 10.1016/j.ultsonch.2019.104876
    Phenolic acids of oak gall were extracted using ultrasonic-probe assisted extraction (UPAE) method in the presence of ionic liquid. It was compared with classical ultrasonic-bath assisted extraction (CUBAE) and conventional aqueous extraction (CAE) method, with and without the presence of ionic liquid. Remarkably, the UPAE method yielded two-fold higher extraction yield with the presence of ionic liquid, resulting 481.04 mg/g for gallic acids (GA) and 2287.90 mg/g for tannic acids (TA), while a decreased value of 130.36 mg/g for GA and 1556.26 mg/g for TA were resulted with the absence of ionic liquid. Intensification process resulted the highest yield of 497.34 mg/g and 2430.48 mg/g for GA and TA, respectively, extracted at temperature 50 °C with sonication intensity of 8.66 W/cm2 and 10% duty cycle, diluted in ionic liquid, 1-Butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, [Bmim][Tf2N] at concentration of 0.10 M with sample-to-solvent ratio 1:10 for 8 h. Peleg's model successfully predicted the UPAE process confirming that extraction capacity is the controlling factor in extracting phenolic acids. Hence, it can be concluded that UPAE method and ionic liquid have synergistic effect as it effectively enhanced the extraction efficiency to increase the bioactive constituents yield.
  6. Karami N, Mohammadi P, Zinatizadeh A, Falahi F, Aghamohammadi N
    Ultrason Sonochem, 2018 Sep;46:89-98.
    PMID: 29739516 DOI: 10.1016/j.ultsonch.2018.04.009
    The biomass concentration of conventional activated sludge (CAS) process due to low sludge sedimentation in clarifiers is limited to 3000 mg/L. In this study, high-frequency ultrasound wave (1.8 MHz) was applied to enhance the CAS process performance using high Mixed Liquor Suspended Solid (MLSS) concentration. The study conducted using a pilot scale CAS bioreactor (with and without ultrasound) and their performance for treating a hospital wastewater were compared. Experimental conditions were designed based on a Central Composite Design (CCD). The sets of data analyzed, modeled and optimized using Response Surface Methodology (RSM). The effect of MLSS concentration 3000-8000 mg/L and hydraulic retention time (HRT) 2-8 h are considered as operating variables to investigate on process responses. The obtained results showed that high-frequency ultrasound was significantly decreased the sludge volume index (SVI) 50% and effluent turbidity about 88.5% at high MLSS. Also, observed that COD removal of both systems was nearly similar, as the maximum COD removal for sonicated and non-sonicated systems were 92 and 92.5% respectively. However, this study demonstrates that the ultrasound irradiation has not had any negative effect on the microbial activity.
  7. Manickam S, Abidin Nb, Parthasarathy S, Alzorqi I, Ng EH, Tiong TJ, et al.
    Ultrason Sonochem, 2014 Jul;21(4):1519-26.
    PMID: 24485395 DOI: 10.1016/j.ultsonch.2014.01.002
    Palm oil mill effluent (POME) is a highly contaminating wastewater due to its high chemical oxygen demand (COD) and biochemical oxygen demand (BOD). Conventional treatment methods require longer residence time (10-15 days) and higher operating cost. Owing to this, finding a suitable and efficient method for the treatment of POME is crucial. In this investigation, ultrasound cavitation technology has been used as an alternative technique to treat POME. Cavitation is the phenomenon of formation, growth and collapse of bubbles in a liquid. The end process of collapse leads to intense conditions of temperature and pressure and shock waves which assist various physical and chemical transformations. Two different ultrasound systems i.e. ultrasonic bath (37 kHz) and a hexagonal triple frequency ultrasonic reactor (28, 40 and 70 kHz) of 15 L have been used. The results showed a fluctuating COD pattern (in between 45,000 and 60,000 mg/L) while using ultrasound bath alone, whereas a non-fluctuating COD pattern with a final COD of 27,000 mg/L was achieved when hydrogen peroxide was introduced. Similarly for the triple frequency ultrasound reactor, coupling all the three frequencies resulted into a final COD of 41,300 mg/L compared to any other individual or combination of two frequencies. With the possibility of larger and continuous ultrasonic cavitational reactors, it is believed that this could be a promising and a fruitful green process engineering technique for the treatment of POME.
  8. Al-Qirby LM, Radiman S, Siong CW, Ali AM
    Ultrason Sonochem, 2017 Sep;38:640-651.
    PMID: 27553194 DOI: 10.1016/j.ultsonch.2016.08.016
    For the first time, a sonochemical process has been used to synthesis cobalt oxide Co3O4nanoflowers and nanorods morphology in the presence of the ionic liquid 1-Ethyl-3-methylimidazolium tetrafluoroborate [EMIM][BF4] as reaction media and morphology template. Different sonication time periods and different molar ratios of the ionic liquid (IL) were used to investigate their effects on the structural, optical, chemical and magnetic properties of the produced Co3O4nanoparticles. During synthesis process brown powder contains cobalt hydroxide Co(OH)2and cobalt oxyhydroxide (Cobalt hydroxide oxide) CoO(OH) was formed, after calcination in air for 4h at 400°C a black powder of Co3O4nanoparticles was produced. The produced Co3O4nanoparticles properties were characterized by X-ray diffraction (XRD), Field Emission Scanning Electron Microscopy (FE-SEM), transmission electron microscopy (TEM), FTIR spectroscopy, UV-vis spectroscopy, and Vibrating Sample Magnetometer (VSM). To explain the formation mechanism of Co3O4NPs some investigations were carried on the brown powder before calcination.
  9. Mahdi T, Ahmad A, Ripin A, Abdullah TA, Nasef MM, Ali MW
    Ultrason Sonochem, 2015 May;24:184-92.
    PMID: 25432400 DOI: 10.1016/j.ultsonch.2014.11.005
    The ability of sonication phenomena in facilitating separation of azeotropic mixtures presents a promising approach for the development of more intensified and efficient distillation systems than conventional ones. To expedite the much-needed development, a mathematical model of the system based on conservation principles, vapor-liquid equilibrium and sonochemistry was developed in this study. The model that was founded on a single stage vapor-liquid equilibrium system and enhanced with ultrasonic waves was coded using MATLAB simulator and validated with experimental data for ethanol-ethyl acetate mixture. The effects of both ultrasonic frequency and intensity on the relative volatility and azeotropic point were examined, and the optimal conditions were obtained using genetic algorithm. The experimental data validated the model with a reasonable accuracy. The results of this study revealed that the azeotropic point of the mixture can be totally eliminated with the right combination of sonication parameters and this can be utilized in facilitating design efforts towards establishing a workable ultrasonically intensified distillation system.
  10. Mohammadi P, Karami N, Zinatizadeh AA, Falahi F, Aghamohammadi N, Almasi A
    Ultrason Sonochem, 2019 Jan 22.
    PMID: 30712854 DOI: 10.1016/j.ultsonch.2019.01.030
    In this study, high-frequency ultrasound wave (1.8 MHz) at low intensity was applied to improve activated sludge settleability at high MLSS concentration. The effect of irradiation intensity, sonication mode, MLSS concentration and sample volume on the physical characteristics of sludge in a pilot scale settling column were investigated for optimizing the conditions. The obtained results showed that high-frequency ultrasound decreased the height of sludge (44%) and effluent turbidity (82.2%) and increased sludge settling velocity about 3 times at high biomass concentration. Irradiation intensity of 0.4 w/cm2 and sonication mode with interval times of 10 s showed the best results on the performance of the system at MLSS concentration of 8000 mg/L with a sample volume of 3 L.
  11. Ameen M, Azizan MT, Ramli A, Yusup S, Alnarabiji MS
    Ultrason Sonochem, 2019 Mar;51:90-102.
    PMID: 30514489 DOI: 10.1016/j.ultsonch.2018.10.011
    Hydrodeoxygenation is one of the promising technologies for the transformation of triglycerides into long-chain hydrocarbon fuel commonly known as green diesel. The hydrodeoxygenation (HDO) of rubber seed oil into diesel range (C15-C18) hydrocarbon over non-sulphided bimetallic (Ni-Mo/γ-Al2O3 solid catalysts were studied. The catalysts were synthesized via wet impregnation method as well as sonochemical method. The synthesized catalysts were subjected to characterization methods including FESEM coupled with EDX, XRD, BET, TEM, XPS, NH3-TPD, CO-chemisorption and H2-TPR in order to investigate the effects of ultrasound irradiations on physicochemical properties of the catalyst. All the catalysts were tested for HDO reaction at 350 °C, 35 bar, H2/oil 1000 N (cm3/cm3) and WHSV = 1 h-1 in fixed bed tubular reactor. The catalyst prepared via sonochemical method showed comparatively higher specific surface area, particles in nano-size and uniform distribution of particle on the external surface of the support, higher crystallinity and lower reduction temperature as well as higher concentration of Mo4+ deoxygenating metal species. These physicochemical properties improved the catalytic activity compared to conventionally synthesized catalyst for HDO of rubber seed oil. The catalytic performance of sonochemically synthesized Ni-Mo/γ-Al2O3 catalyst (80.87%) was higher than the catalyst prepared via wet impregnation method (63.3%). The sonochemically synthesized Ni-Mo/γ-Al2O3 catalyst is found to be active, produces 80.87 wt% of diesel range hydrocarbons, and it gives high selectivity for Pentadecane (18.7 wt%), Hexadecane (16.65 wt%), Heptadecane (24.45 wt%) and Octadecane (21.0 wt%). The product distribution revealed that the deoxygenation reaction pathway was preferred. Higher conversion and higher HDO yield in this study are associated mainly with the change in concentration ratio between oxidation states of molybdenum (Mo4+, Mo5+, and Mo6+) on the external surface of the catalyst due to ultrasound irradiation during the synthesis process. Consequently, the application of sonochemically synthesized non-sulphided catalysts favored mainly hydrodeoxygenation of diesel range hydrocarbon.
  12. Mahbubul IM, Elcioglu EB, Saidur R, Amalina MA
    Ultrason Sonochem, 2017 Jul;37:360-367.
    PMID: 28427644 DOI: 10.1016/j.ultsonch.2017.01.024
    Nanofluids are promising in many fields, including engineering and medicine. Stability deterioration may be a critical constraint for potential applications of nanofluids. Proper ultrasonication can improve the stability, and possibility of the safe use of nanofluids in different applications. In this study, stability properties of TiO2-H2O nanofluid for varying ultrasonication durations were tested. The nanofluids were prepared through two-step method; and electron microscopies, with particle size distribution and zeta potential analyses were conducted for the evaluation of their stability. Results showed the positive impact of ultrasonication on nanofluid dispersion properties up to some extent. Ultrasonication longer than 150min resulted in re-agglomeration of nanoparticles. Therefore, ultrasonication for 150min was the optimum period yielding highest stability. A regression analysis was also done in order to relate the average cluster size and ultrasonication time to zeta potential. It can be concluded that performing analytical imaging and colloidal property evaluation during and after the sample preparation leads to reliable insights.
  13. Aishah Baharuddin S, Nadiah Abd Karim Shah N, Saiful Yazan L, Abd Rashed A, Kadota K, Al-Awaadh AM, et al.
    Ultrason Sonochem, 2023 Dec;101:106702.
    PMID: 38041881 DOI: 10.1016/j.ultsonch.2023.106702
    Colorectal cancer (CRC) is the most common malignancy and the third primary cause of cancer-related mortalities caused by unhealthy diet, hectic lifestyle, and genetic damage. People aged ≥ 50 are more at risk for CRC. Nowadays, bioactive compounds from plants have been widely studied in preventing CRC because of their anticancer and antioxidant properties. Herein, ultrasound-assisted extraction (UAE) was used to extract the bioactive compounds of Pluchea indica (L.) leaves. The resultant total phenolic content (TPC) and total flavonoid content (TFC) of P. indica (L.) leaves were analyzed using a response surface methodology (RSM). The central composite design was implemented to evaluate the amplitude (10 %-70 %) and treatment time (2-10 min) on both responses, i.e., TPC and TFC of P. indica (L.) leaves. The optimum UAE conditions were observed 40 % amplitude and 6 min of treatment, where the TPC and TFC were 3.26 ± 0.00 mg GAE/g d.w. and 67.58 ± 1.46 mg QE/g d.w., respectively. The optimum P. indica (L.) leaf extract was then screened for its cytotoxicity on the HT-29 colorectal cancer cell line. This extract had strong cytotoxicity with a half-maximal inhibitory concentration value (IC50) of 12 µg/mL. The phytochemical screening of bioactive compounds revealed that the optimal P. indica (L.) leaf extract contains flavonoids, namely, kaempferol 3-[2''',3''',5'''-triacetyl]-alpha-L-arabinofuranosyl-(1->6)-glucoside, myricetin 3-glucoside-7-galactoside, quercetin 3-(3''-sulfatoglucoside), and kaempferol 7,4'-dimethyl ether 3-O-sulfate, which could be good sources for promising anticancer agents. This study employs the RSM approach to utilize UAE for bioactive compounds extraction of P. indica (L.) leaves, identified the specific compounds present in the optimized extract and revealed its potential in preventing CRC.
  14. Sabaruddin FA, Megashah LN, Shazleen SS, Ariffin H
    Ultrason Sonochem, 2023 Oct;99:106572.
    PMID: 37696213 DOI: 10.1016/j.ultsonch.2023.106572
    The utilization of agricultural residues to obtain biocompounds of high-added value has significantly increased in the past decades. The conversion of agro-based residues into valuable products appears to be an economically efficient, environment-friendly, and protracted waste management practice. The implementation of ultrasonic technologies in the conversion of value-added goods from agricultural waste materials through pre-treatment and valorization processes has imparted many advantageous effects including rapid processing, effective process performance, minimization of processing steps, minimal dependency on harmful chemicals, and an increased yield and properties of bio-products. To further enliven the literature and inspire new research investigations, this review covers the comprehensive work including theoretical principles, processes, and potential benefits of ultrasonic treatment technologies to assist the production of bio-products which emphasize the extraction yield and the characteristic of the end-product extracted from agriculture residues. A detailed evaluation of these methods and key aspects impacting their performance as well as the features and shortcomings of each ultrasound-assisted approach is also discussed. This review also addressed some of the challenges associated with using ultrasonic irradiation and proposed several potential techniques to maximize productivity. Understanding the concept of ultrasonication technique allow the academician and industrial practitioners to explore the possibility of applying a greener and sustainable approach of biomass extraction to be translated into higher scale production of commercial products.
  15. Zakaria F, Tan JK, Mohd Faudzi SM, Abdul Rahman MB, Ashari SE
    Ultrason Sonochem, 2021 Dec;81:105851.
    PMID: 34864545 DOI: 10.1016/j.ultsonch.2021.105851
    The optimisation of the Ultrasound-Assisted Extraction (UAE) method was investigated by employing the Central Composite Rotatable Design (CCRD) of Response Surface Methodology (RSM). The UAE method was based on a simple ultrasound treatment using methanol as the extraction medium to facilitate the cell disruption of Mitragyna speciosa leaves for optimum extraction yield and Total Phenolic Content (TPC). Three different parameters comprising extraction temperature (X1: 25-50 °C), sonication time (X2: 15-50 min), and solvent to solid ratio (X3: 10-30 mL/g), and were selected as the independent variables, while two response variables were selected, namely extraction yield (Y1) and TPC (Y2). Based on the results, the developed quadratic polynomial model correlated with the experimental data is based on the coefficient of determination (R2) of extraction yield (0.9972, p 
  16. Yusof NS, Ashokkumar M
    Ultrason Sonochem, 2015 May;24:8-12.
    PMID: 25465878 DOI: 10.1016/j.ultsonch.2014.11.003
    A comprehensive investigation on the effect of ultrasonic frequency and power on the structural transformation of CTABr/NaSal micelles has been carried out. Sonication of this micelle system at various ultrasonic frequencies and power resulted in the formation and separation of two types of micelles. High viscoelastic threadlike micelles of ∼ 2 nm in diameter and several μm in length and tubular micelles possessing a viscosity slightly above that of water with ∼ 30-50 nm diameter and few hundred nm length. The structural transformation of micelles was induced by the shear forces generated during acoustic cavitation. At a fixed acoustic power of 40 W, the structural transformation was found to decrease from 211 to 647 kHz frequency due to the decreasing shear forces generated, as evidenced by rheological measurements and cryo-TEM images. At 355 kHz, an increase in the structural transformation was observed with an increase in acoustic power. These findings provide a knowledge base that could be useful for the manipulation of viscosity of micelles that may have applications in oil industry.
  17. Yusof NS, Babgi B, Alghamdi Y, Aksu M, Madhavan J, Ashokkumar M
    Ultrason Sonochem, 2016 Mar;29:568-76.
    PMID: 26142078 DOI: 10.1016/j.ultsonch.2015.06.013
    Acoustic cavitation in a liquid medium generates several physical and chemical effects. The oscillation and collapse of cavitation bubbles, driven at low ultrasonic frequencies (e.g., 20 kHz), can generate strong shear forces, microjets, microstreaming and shockwaves. Such strong physical forces have been used in cleaning and flux improvement of ultrafiltration processes. These physical effects have also been shown to deactivate pathogens. The efficiency of deactivation of pathogens is not only dependent on ultrasonic experimental parameters, but also on the properties of the pathogens themselves. Bacteria with thick shell wall are found to be resistant to ultrasonic deactivation process. Some evidence does suggest that the chemical effects (radicals) of acoustic cavitation are also effective in deactivating pathogens. Another aspect of cleaning, namely, purification of water contaminated with organic and inorganic pollutants, has also been discussed in detail. Strong oxidising agents produced within acoustic cavitation bubbles could be used to degrade organic pollutants and convert toxic inorganic pollutants to less harmful substances. The effect of ultrasonic frequency and surface activity of solutes on the sonochemical degradation efficiency has also been discussed in this overview.
  18. Rajamma DB, Anandan S, Yusof NSM, Pollet BG, Ashokkumar M
    Ultrason Sonochem, 2021 Apr;72:105413.
    PMID: 33338865 DOI: 10.1016/j.ultsonch.2020.105413
    Acoustic cavitation and sonochemical reactions play a significant role in various applications of ultrasound. A number of dosimetry methods are in practice to quantify the amount of radicals generated by acoustic cavitation. In this study, hydroxyl radical (OH) yields measured by Weissler, Fricke and terephthalic acid dosimetry methods have been compared to evaluate the validities of these methods using a 490 kHz high frequency sonochemical reactor. The OH yields obtained after 5 min sonication at 490 kHz from Weissler and Fricke dosimetries were 200 µM and 289 µM, respectively. Whereas, the OH yield was found to be very low (8 µM) when terephthalic acid dosimetry was used under similar experimental conditions. While the results agree with those reported by Iida et al. (Microchem. J., 80 (2005) 159), further mechanistic details and interfering reactions have been discussed in this study. For example, the amount of OH determined by the Weissler and Fricke methods may have some uncertainty due to the formation of HO2 in the presence of oxygen. In order to account for the major discrepancy observed with the terephthalic acid dosimetry method, high performance liquid chromatography (HPLC) analysis was performed, where two additional products other than 2-hydroxy terephthalic acid were observed. Electrospray ionization mass spectrometry (ESI-MS) analysis showed the formation of 2,5-dihydroxyterephthalic acid as one of the by-products along with other unidentified by-products. Despite the formation of additional products consuming OH, the reason for a very low OH yield obtained by this dosimetry could not be justified, questioning the applicability of this method, which has been used to quantify OH yields generated not only by acoustic cavitation, but also by other processes such as γ-radiolysis. The authors are hoping that this Opinion Paper may initiate further discussion among researchers working in sonochemistry area that could help resolve the uncertainties around using these dosimetry methods.
  19. Tiong TJ, Chu JK, Lim LY, Tan KW, Hong Yap Y, Asli UA
    Ultrason Sonochem, 2019 Sep;56:46-54.
    PMID: 31101285 DOI: 10.1016/j.ultsonch.2019.03.026
    In the field of ultrasonic emulsification, the formation and cavitation collapse is one major factor contributing to the formation of micro- and nano-sized emulsion droplets. In this work, a series of experiments were conducted to examine the effects of varying the ultrasonic horn's position to the sizes of emulsion droplets formed, in an attempt to compare the influence of the simulated acoustic pressure fields to the experimental results. Results showed that the intensity of the acoustic pressure played a vital role in the formation of smaller emulsion droplets. Larger areas with acoustic pressure above the cavitation threshold in the water phase have resulted in the formation of smaller emulsion droplets ca. 250 nm and with polydispersity index of 0.2-0.3. Placing the ultrasonic horn at the oil-water interface has hindered the formation of small emulsion droplets, due to the transfer of energy to overcome the interfacial surface tension of oil and water, resulting in a slight reduction in the maximum acoustic pressure, as well as the total area with acoustic pressures above the cavitation threshold. This work has demonstrated the influence of the position of the ultrasonic horn in the oil and water system on the final emulsion droplets formed and can conclude the importance of generating acoustic pressure above the cavitation threshold to achieve small and stable oil-in-water emulsion.
  20. Rayathulhan R, Sodipo BK, Aziz AA
    Ultrason Sonochem, 2017 Mar;35(Pt A):270-275.
    PMID: 27756524 DOI: 10.1016/j.ultsonch.2016.10.002
    ZnO nanorods were directly grown on four different wires (silver, nickel, copper, and tungsten) using sonochemical method. Zinc nitrate hexahydrate and hexamethylenetetramine (HMT) were used as precursors. Influence of growth parameters such as precursors' concentration and ultrasonic power on the grown nanorods were determined. The results demonstrated that the precursor concentration affected the growth structure and density of the nanorods. The morphology, distribution, and orientation of nanorods changed as the ultrasonic power changed. Nucleation of ZnO nanorods on the wire occurred at lower ultrasonic power and when the power increased, the formation and growth of ZnO nanorods on the wires were initiated. The best morphology, size, distribution, and orientation of the nanorods were observed on the Ag wire. The presence of single crystal nanorod with hexagonal shaped was obtained. This shape indicates that the ZnO nanorods corresponded to the hexagonal wurtzite structure with growth preferential towards the (002) direction.
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links