Displaying publications 1 - 20 of 86 in total

Abstract:
Sort:
  1. Majeed Butt O, Shakeel Ahmad M, Kai Lun T, Seng Che H, Fayaz H, Abd Rahim N, et al.
    Waste Manag, 2023 Feb 01;156:1-11.
    PMID: 36424243 DOI: 10.1016/j.wasman.2022.11.016
    The integration of hydrogen in the primary energy mix requires a major technological shift in virtually every energy-related application. This study has attempted to investigate the techno-economic solar photovoltaic (PV) integrated water electrolysis and waste incineration system. Three different strategies, i.e., (i) PV + Battery(Hybrid mode with required batteries); (ii) auto-ignition (Direct coupling); and (iii) PV + Secondary-Electrolyzer(Direct coupling assisted with secondary electrolyzer), have been envisioned. The 'PV + Battery' consume 42.42 % and 15.07 % less energy than the auto-ignition and 'PV + Secondary-Electrolyzer' methods. However, the capital cost of 'PV + Battery' has been calculated to be 15.4 % and 11.8 % more than auto-ignition and 'PV + Secondary-Electrolyzer, respectively.The energy consumption relative to waste input, the 'PV + Battery' method used 80 % less energy, while auto-ignition and 'PV + Secondary-Electrolyzer' showed 70.5 % and 77.5 % less energy, respectively. Furthermore, these approaches showed a vast difference in cost-benefit for the longer run. 'PV + Battery' was forecasted to be 73.3 % and 23.3 % more expensive than auto-ignition and 'PV + Secondary-Electrolyzer' methods, respectively, for 30 years. Overall, this study can benefit from using either of these methods depending on the application, usage scale, and climatic conditions.
  2. Mohajerani A, Kadir AA, Larobina L
    Waste Manag, 2016 Jun;52:228-44.
    PMID: 26975623 DOI: 10.1016/j.wasman.2016.03.012
    The disposal and littering of cigarette butts (CBs) is a serious environmental problem. Trillions of cigarettes are produced every year worldwide, resulting in millions of tonnes of toxic waste being dumped into the environment in the form of cigarette butts. As CBs have poor biodegradability, it can take many years for them to break down. This paper reviews and presents some of the results of a study on the recycling of CBs into fired clay bricks. Bricks with 2.5%, 5%, 7.5%, and 10% CB content by weight were manufactured and tested, and then compared against control clay bricks with 0% CB content. The results showed that the dry density decreased by up to 30% and the compressive strength decreased by 88% in bricks with 10% CBs. The calculated compressive strength of bricks with 1% CBs was determined to be 19.53Mpa. To investigate the effect of mixing time, bricks with 7.5% CB content were manufactured with different mixing times of 5, 10, and 15min. To test the effect of heating time on the properties of CB bricks, the heating rate used during manufacturing was changed to 0.7, 2, 5, and 10°Cmin(-1). Bricks with 0% and 5% CB content were fired with these heating rates. Leachate tests were carried out for bricks with 0%, 2.5%, 5%, and 10% CB content. The emissions released during firing were tested for bricks with 0% and 5% CB content using heating rates of 0.7, 2, 5, and 10°Cmin(-1). The gases tested were carbon monoxide (CO), carbon dioxide (CO2), chlorine (Cl2), nitrogen oxide (NO), and hydrogen cyanide (HCN). Finally, estimations were made for the energy that could be saved by firing bricks incorporating CBs. Calculations showed that up to 58% of the firing energy could potentially be saved. Bricks were shown to be a viable solution for the disposal of CBs. They can reduce contamination caused by cigarette butts and provide a masonry construction material that can be either loadbearing or non-loadbearing, depending on the quantity of CBs incorporated. This paper proposes the use of bricks with 1% CB content throughout the brick-manufacturing industry. If bricks contained as little as 1% CB content, they would still provide a solution for the issue of CB recycling while maintaining properties very similar to those of a non-CB brick. Our calculations show that, theoretically, only 2.5% of the world's annual brick production is necessary to completely offset the worldwide, annual cigarette production.
  3. Hannan MA, Abdulla Al Mamun M, Hussain A, Basri H, Begum RA
    Waste Manag, 2015 Sep;43:509-23.
    PMID: 26072186 DOI: 10.1016/j.wasman.2015.05.033
    In the backdrop of prompt advancement, information and communication technology (ICT) has become an inevitable part to plan and design of modern solid waste management (SWM) systems. This study presents a critical review of the existing ICTs and their usage in SWM systems to unfold the issues and challenges towards using integrated technologies based system. To plan, monitor, collect and manage solid waste, the ICTs are divided into four categories such as spatial technologies, identification technologies, data acquisition technologies and data communication technologies. The ICT based SWM systems classified in this paper are based on the first three technologies while the forth one is employed by almost every systems. This review may guide the reader about the basics of available ICTs and their application in SWM to facilitate the search for planning and design of a sustainable new system.
  4. Haroun M, Idris A, Syed Omar SR
    Waste Manag, 2007;27(11):1541-50.
    PMID: 17113767
    Tannery waste is categorized as toxic and hazardous in Malaysia due to its high content of Cr (in excess of 500 mg/kg) and other heavy metals. Heavy metals, when in high enough concentrations, have the potential to be both phytotoxic and zootoxic. Heavy metals are found as contaminants in tannery sludge. This investigation aimed to identify the fate of chromium, cadmium, copper, lead, and zinc concentrations in tannery sludge throughout a 50-day composting cycle. The results of this study showed a general increase in the removal of Cr, Cd, Pb, and to a much smaller extent Zn and Cu, manifested by a decrease in their overall concentrations within the solid fraction of the final product (the decreases were likely the result of leaching). Furthermore, in using a sequential extraction method for sludge composting at different phases of treatment, a large proportion of the heavy metals were found to be associated to the residual fraction (70-80%) and fractions more resistant to extraction, X-NaOH, X-EDTA, X-HNO3 (12-29%). Less than 2% of the metals were bound to bioavailable fractions X-(KNO3+H2O).
  5. Liang Y, Tan Q, Song Q, Li J
    Waste Manag, 2021 Jan 01;119:242-253.
    PMID: 33091837 DOI: 10.1016/j.wasman.2020.09.049
    It is well known that Asia generates and receives large quantities of plastic waste. Through a detailed study of plastic waste generation and trade, the management and treatment of plastic waste in Asia were analyzed from the regional perspective. The amounts of plastic waste in municipal solid waste and in industrial solid waste were estimated to be 79 Mt and 42 Mt, respectively, in Asia. The overall treatment and recycling status in Asia are unsatisfactory. Asia imported 74% of the plastic waste in the world in 2016, and China (mainland) imported the most plastic waste until 2017, with 5.8 to 8.3 Mt. In 2017, about half the plastic waste imported by Asia came from other regions, and after subtracting the exported quantity, 98% of the plastic waste was left in Asia for treatment and disposal. The plastic waste imported by Asia declined about 72% in monetary value in 2018. There is still a large gap between the plastic waste quantity imported to Asia and that exported from Asia. China's ban of plastic waste imports caused import quantities to drop to 52 kt in 2018, simultaneously, exports from the largest exporting countries or regions such as Hong Kong (China), the USA, Japan, and Germany decreased. While Vietnam, Malaysia and some other Asian countries and regions saw significant increases in plastic waste imports from 2016 to 2018. Considering this situation, countries in Asia are starting to strictly limit plastic waste imports from other countries.
  6. Karim Ghani WA, Rusli IF, Biak DR, Idris A
    Waste Manag, 2013 May;33(5):1276-81.
    PMID: 23415709 DOI: 10.1016/j.wasman.2012.09.019
    Tremendous increases in biodegradable (food waste) generation significantly impact the local authorities, who are responsible to manage, treat and dispose of this waste. The process of separation of food waste at its generation source is identified as effective means in reducing the amount food waste sent to landfill and can be reused as feedstock to downstream treatment processes namely composting or anaerobic digestion. However, these efforts will only succeed with positive attitudes and highly participations rate by the public towards the scheme. Thus, the social survey (using questionnaires) to analyse public's view and influencing factors towards participation in source separation of food waste in households based on the theory of planned behaviour technique (TPB) was performed in June and July 2011 among selected staff in Universiti Putra Malaysia, Serdang, Selangor. The survey demonstrates that the public has positive intention in participating provided the opportunities, facilities and knowledge on waste separation at source are adequately prepared by the respective local authorities. Furthermore, good moral values and situational factors such as storage convenience and collection times are also encouraged public's involvement and consequently, the participations rate. The findings from this study may provide useful indicator to the waste management authorities in Malaysia in identifying mechanisms for future development and implementation of food waste source separation activities in household programmes and communication campaign which advocate the use of these programmes.
  7. Hannan MA, Arebey M, Begum RA, Basri H
    Waste Manag, 2012 Dec;32(12):2229-38.
    PMID: 22749722 DOI: 10.1016/j.wasman.2012.06.002
    An advanced image processing approach integrated with communication technologies and a camera for waste bin level detection has been presented. The proposed system is developed to address environmental concerns associated with waste bins and the variety of waste being disposed in them. A gray level aura matrix (GLAM) approach is proposed to extract the bin image texture. GLAM parameters, such as neighboring systems, are investigated to determine their optimal values. To evaluate the performance of the system, the extracted image is trained and tested using multi-layer perceptions (MLPs) and K-nearest neighbor (KNN) classifiers. The results have shown that the accuracy of bin level classification reach acceptable performance levels for class and grade classification with rates of 98.98% and 90.19% using the MLP classifier and 96.91% and 89.14% using the KNN classifier, respectively. The results demonstrated that the system performance is robust and can be applied to a variety of waste and waste bin level detection under various conditions.
  8. Islam R, Nazifa TH, Yuniarto A, Shanawaz Uddin ASM, Salmiati S, Shahid S
    Waste Manag, 2019 Jul 15;95:10-21.
    PMID: 31351595 DOI: 10.1016/j.wasman.2019.05.049
    Associated with the continuing increase of construction activities such as infrastructure projects, commercial buildings and housing programs, Bangladesh has been experiencing a rapid increase of construction and demolition (C&D) waste. Till now, the generation rate of C&D waste has not been well understood or not explicitly documented in Bangladesh. This study aims to provide an approach to estimate C&D waste generation using waste generation rates (WGR) through regression analysis. Furthermore, analyses the economic benefit of recycling C&D waste. The results revealed that WGR 63.74 kg/m2 and 1615 kg/m2 for construction and demolition activities respectively. Approximately, in financial year (FY) 2016, 1.28 million tons (0.149 construction and 1.139 demolition) waste were generated in Dhaka city, of which the three largest proportions were concrete (60%), brick/block (21%) and mortar (9%). After collection they were dumped in either landfills or unauthorized places. Therefore, it can be summarized as: waste is a resource in wrong place. The results of this study indicate that rapid urbanization of Dhaka city would likely experience the peak in the generation of C&D waste. This paper thus designates that C&D waste recycling is an entrepreneurial activity worth venturing into and an opportunity for extracting economic and environmental benefits from waste. The research findings also show that recycling of concrete and brick waste can add economic value of around 44.96 million USD. In addition, recycling of C&D waste leads to important reductions in CO2 emissions, energy use, natural resources and illegal landfills. Therefore, the findings of WGR and economic values provide valuable quantitative information for the future C&D waste management exercises of various stakeholders such as government, industry and academy.
  9. Kumari K, Suresh S, Arisutha S, Sudhakar K
    Waste Manag, 2018 Jul;77:545-554.
    PMID: 29778405 DOI: 10.1016/j.wasman.2018.05.007
    Anaerobic co-digestion has made a greater impact on the biogas production from mixing different type of waste. In this research, sewage sludge (SS) and cow manure (CM), was used as a primary waste along with kitchen waste (KW), yard waste (YW), floral waste (FW) and dairy wastewater (DWW) as co-substrate for anaerobic digestion. Mixtures with a ratio of 1:2 ratio is fed into a single stage up-flow anaerobic sludge blanket (UASB) reactor. Digestion was carried out in a mesophilic temperature range for 20 days. pH and VFA were measured and ranged from 5 to 7.5 and 3500-500 mg/L, respectively, for all the mixtures throughout the digestion period. Percentage of COD removal efficiency after 20 days was found to be in the range of 76-86%. The maximum biogas production rate was found to be 4500 mL/day. Characterization of the final residue from each of the digesters was carried out by Scanning Electron microscope, Energy dispersive, thermogravimetric, FTIR Spectra, and Atomic microscope. Thermal analysis reveals that spent sludge can be potential waste energy sources.
  10. Malakahmad A, Abualqumboz MS, Kutty SRM, Abunama TJ
    Waste Manag, 2017 Dec;70:282-292.
    PMID: 28935377 DOI: 10.1016/j.wasman.2017.08.044
    Malaysian authorities has planned to minimize and stop when applicable unsanitary dumping of waste as it puts human health and the environment at elevated risk. Cost, energy and revenue are mostly adopted to draw the blueprint of upgrading municipal solid waste management system, while the carbon footprint emissions criterion rarely acts asa crucial factor. This study aims to alert Malaysian stakeholders on the uneven danger of carbon footprint emissions of waste technologies. Hence, three scenarios have been proposed and assessed mainly on the carbon footprint emissions using the 2006 IPCC methodology. The first scenario is waste dumping in sanitary landfills equipped with gas recovery system, while the second scenario includes anaerobic digestion of organics and recycling of recyclable wastes such as plastic, glass and textile wastes. The third scenario is waste incineration. Besides the carbon footprint emissions criterion, other environmental concerns were also examined. The results showed that the second scenario recorded the lowest carbon footprint emissions of 0.251t CO2 eq./t MSW while the third scenario had the highest emissions of 0.646t CO2 eq./t MSW. Additionally, the integration between anaerobic digestion and recycling techniques caused the highest avoided CO2 eq. emissions of 0.74t CO2 eq./t MSW. The net CO2 eq. emissions of the second scenario equaled -0.489t CO2 eq./t MSW due to energy recovery from the biogas and because of recycled plastic, glass and textile wastes that could replace usage of raw material. The outcomes also showed that the first scenario generates huge amount of leachate and hazardous air constituents. The study estimated that a ton of dumped waste inside the landfills generates approximately 0.88m3 of trace risky compounds and 0.188m3 of leachate. As for energy production, the results showed that the third scenario is capable of generating 639kWh/t MSW followed by the second scenario with 387.59kWh/t MSW. The first scenario produced 296.79kWh/t MSW. In conclusion, the outcomes of this study recommend an integrated scenario of anaerobic digestion and recycling techniques to be employed in Malaysia.
  11. Saeed MO, Hassan MN, Mujeebu MA
    Waste Manag, 2009 Jul;29(7):2209-13.
    PMID: 19369061 DOI: 10.1016/j.wasman.2009.02.017
    This paper presents a forecasting study of municipal solid waste generation (MSWG) rate and potential of its recyclable components in Kuala Lumpur (KL), the capital city of Malaysia. The generation rates and composition of solid wastes of various classes such as street cleansing, landscape and garden, industrial and constructional, institutional, residential and commercial are analyzed. The past and present trends are studied and extrapolated for the coming years using Microsoft office 2003 Excel spreadsheet assuming a linear behavior. The study shows that increased solid waste generation of KL is alarming. For instance, the amount of daily residential SWG is found to be about 1.62 kg/capita; with the national average at 0.8-0.9 kg/capita and is expected to be increasing linearly, reaching to 2.23 kg/capita by 2024. This figure seems reasonable for an urban developing area like KL city. It is also found that, food (organic) waste is the major recyclable component followed by mix paper and mix plastics. Along with estimated population growth and their business activities, it has been observed that the city is still lacking in terms of efficient waste treatment technology, sufficient fund, public awareness, maintaining the established norms of industrial waste treatment etc. Hence it is recommended that the concerned authority (DBKL) shall view this issue seriously.
  12. Akhtar M, Hannan MA, Begum RA, Basri H, Scavino E
    Waste Manag, 2017 Mar;61:117-128.
    PMID: 28153405 DOI: 10.1016/j.wasman.2017.01.022
    Waste collection is an important part of waste management that involves different issues, including environmental, economic, and social, among others. Waste collection optimization can reduce the waste collection budget and environmental emissions by reducing the collection route distance. This paper presents a modified Backtracking Search Algorithm (BSA) in capacitated vehicle routing problem (CVRP) models with the smart bin concept to find the best optimized waste collection route solutions. The objective function minimizes the sum of the waste collection route distances. The study introduces the concept of the threshold waste level (TWL) of waste bins to reduce the number of bins to be emptied by finding an optimal range, thus minimizing the distance. A scheduling model is also introduced to compare the feasibility of the proposed model with that of the conventional collection system in terms of travel distance, collected waste, fuel consumption, fuel cost, efficiency and CO2 emission. The optimal TWL was found to be between 70% and 75% of the fill level of waste collection nodes and had the maximum tightness value for different problem cases. The obtained results for four days show a 36.80% distance reduction for 91.40% of the total waste collection, which eventually increases the average waste collection efficiency by 36.78% and reduces the fuel consumption, fuel cost and CO2 emission by 50%, 47.77% and 44.68%, respectively. Thus, the proposed optimization model can be considered a viable tool for optimizing waste collection routes to reduce economic costs and environmental impacts.
  13. Zainudin MH, Mustapha NA, Maeda T, Ramli N, Sakai K, Hassan M
    Waste Manag, 2020 Apr 01;106:240-249.
    PMID: 32240940 DOI: 10.1016/j.wasman.2020.03.029
    Biochar has proven to be a feasible additive for mitigating nitrogen loss during the composting process. This study aims to evaluate the influence of biochar addition on bacterial community and physicochemical properties changes, including ammonium (NH4+), nitrite (NO2-) and nitrate (NO3-) contents during the composting of poultry manure. The composting was carried out by adding 20% (w/w) of biochar into the mixture of poultry manure and rice straw with a ratio of 2:1, and the same treatment without biochar was prepared as a control. The finished product of control compost recorded the high contents of NO2- and NO3- (366 mg/kg and 600 mg/kg) with reduced the total NH4+ content to 10 mg/kg. Meanwhile, biochar compost recorded a higher amount of total NH4+ content (110 mg/kg) with low NO2- and NO3- (161 mg/kg and 137 mg/kg) content in the final composting material. The principal component analysis showed that the dynamics of dominant genera related to Halomonas, Pusillimonas, and Pseudofulvimonas, all of which were known as nitrifying and denitrifying bacteria, was significantly correlated with the dynamic of NO2- and NO3- content throughout the composting process. The genera related to Pusillimonas, and Pseudofulvimonas appeared as the dominant communities as the NO2- and NO3- increased. In contrast, as the NO2- and NO3- concentration decreased, the Halomonas genus were notably enriched in biochar compost. This study revealed the bacterial community shifts corresponded with the change of physicochemical properties, which provides essential information for a better understanding of monitoring and improving the composting process.
  14. Hannan MA, Akhtar M, Begum RA, Basri H, Hussain A, Scavino E
    Waste Manag, 2018 Jan;71:31-41.
    PMID: 29079284 DOI: 10.1016/j.wasman.2017.10.019
    Waste collection widely depends on the route optimization problem that involves a large amount of expenditure in terms of capital, labor, and variable operational costs. Thus, the more waste collection route is optimized, the more reduction in different costs and environmental effect will be. This study proposes a modified particle swarm optimization (PSO) algorithm in a capacitated vehicle-routing problem (CVRP) model to determine the best waste collection and route optimization solutions. In this study, threshold waste level (TWL) and scheduling concepts are applied in the PSO-based CVRP model under different datasets. The obtained results from different datasets show that the proposed algorithmic CVRP model provides the best waste collection and route optimization in terms of travel distance, total waste, waste collection efficiency, and tightness at 70-75% of TWL. The obtained results for 1 week scheduling show that 70% of TWL performs better than all node consideration in terms of collected waste, distance, tightness, efficiency, fuel consumption, and cost. The proposed optimized model can serve as a valuable tool for waste collection and route optimization toward reducing socioeconomic and environmental impacts.
  15. Cheong CW, Lee YS, Ahmad SA, Ooi PT, Phang LY
    Waste Manag, 2018 Sep;79:658-666.
    PMID: 30343798 DOI: 10.1016/j.wasman.2018.08.029
    A huge amount of feathers is generated as a waste every year. Feathers can be a protein source if it is treated with an appropriate method. The present study investigates feasibility of autoclave alkaline and microwave alkaline pretreatments to be combined with enzymatic treatment for feather solubilization and protein production. Hydrolysis of chicken feather by autoclave alkaline pretreatment followed by an enzymatic method (AAS) or microwave alkaline pretreatment followed by an enzymatic method (MAS) was optimized by response surface methodology. Various NaOH concentrations for autoclave alkaline pretreatment (0.01-0.1 M) and microwave-alkaline pretreatment (0.01-0.05 M) were applied. The holding time for both pretreatments ranged from 1 to 10 min. The pretreated feathers were subjected to enzymatic hydrolysis using a commercial enzyme prior to analysis of protein content, feather solubilization, functional groups, and elemental composition (carbon, hydrogen, nitrogen and sulfur) of the treated feathers. The results revealed that both autoclave alkaline pretreatment and microwave alkaline pretreatment under optimized conditions of 0.068 M NaOH, 2 min holding time, 105 °C and 450 W, 0.05 M NaOH for 10 min, respectively, enhanced the subsequent Savinase hydrolysis of chicken feathers to achieve more than 80% degradation and more than 70% protein recovery. Fourier transform infrared spectroscopy results showed that both thermal-alkaline pretreatments weakened the structure of the feather. Reduction of carbon, nitrogen, and sulfur occurred in both thermal-alkaline pretreatments of feathers indicating degradation of the feather as well as protein release. Thermal-alkaline pretreatment may be a promising method for enhancing the enzymatic hydrolysis of chicken feathers and for producing a protein-rich hydrolysate.
  16. Hossain MS, Santhanam A, Nik Norulaini NA, Omar AK
    Waste Manag, 2011 Apr;31(4):754-66.
    PMID: 21186116 DOI: 10.1016/j.wasman.2010.11.008
    The management of clinical solid waste (CSW) continues to be a major challenge, particularly, in most healthcare facilities of the developing world. Poor conduct and inappropriate disposal methods exercised during handling and disposal of CSW is increasing significant health hazards and environmental pollution due to the infectious nature of the waste. This article summarises a literature review into existing CSW management practices in the healthcare centers. The information gathered in this paper has been derived from the desk study of open literature survey. Numerous researches have been conducted on the management of CSW. Although, significant steps have been taken on matters related to safe handling and disposal of the clinical waste, but improper management practice is evident from the point of initial collection to the final disposal. In most cases, the main reasons of the mismanagement of CSW are the lack of appropriate legislation, lack of specialized clinical staffs, lack of awareness and effective control. Furthermore, most of the healthcare centers of the developing world have faced financial difficulties and therefore looking for cost effective disposal methods of clinical waste. This paper emphasizes to continue the recycle-reuse program of CSW materials after sterilization by using supercritical fluid carbon dioxide (SF-CO2) sterilization technology at the point of initial collection. Emphasis is on the priority to inactivate the infectious micro-organisms in CSW. In that case, waste would not pose any threat to healthcare workers. The recycling-reuse program would be carried out successfully with the non-specialized clinical staffs. Therefore, the adoption of SF-CO2 sterilization technology in management of clinical solid waste can reduce exposure to infectious waste, decrease labor, lower costs, and yield better compliance with regulatory. Thus healthcare facilities can both save money and provide a safe environment for patients, healthcare staffs and clinical staffs.
  17. Ghani WA, Alias AB, Savory RM, Cliffe KR
    Waste Manag, 2009 Feb;29(2):767-73.
    PMID: 18614348 DOI: 10.1016/j.wasman.2008.03.025
    Power generation from biomass is an attractive technology that utilizes agricultural residual waste. In order to explain the behavior of biomass-fired fluidized bed incinerator, biomass sources from agricultural residues (rice husk and palm kernel) were co-fired with coal in a 0.15m diameter and 2.3m high fluidized bed combustor. The combustion efficiency and carbon monoxide emissions were studied and compared with those for pure coal combustion. Co-combustion of a mixture of biomass with coal in a fluidized bed combustor designed for coal combustion increased combustion efficiency up to 20% depending upon excess air levels. Observed carbon monoxide levels fluctuated between 200 and 900 ppm with the addition of coal. It is evident from this research that efficient co-firing of biomass with coal can be achieved with minimal modifications to existing coal-fired boilers.
  18. Aghbashlo M, Tabatabaei M, Soltanian S, Ghanavati H, Dadak A
    Waste Manag, 2019 Mar 15;87:485-498.
    PMID: 31109549 DOI: 10.1016/j.wasman.2019.02.029
    A comprehensive exergoeconomic performance analysis of a municipal solid waste digestion plant integrated with a biogas genset was conducted throughout this study in order to highlight its bottlenecks for further improvements. Exergoeconomic performance parameters of each component of the plant were determined by solving exergy and cost balance equations based on Specific Exergy Costing (SPECO) approach. The analysis was conducted to reveal the cost structure of the plant based on actual operating information and economic data. The exergy unitary cost of two main products of the plant, i.e., bioelectricity and biofertilizer were determined at 26.27 and 2.27 USD/GJ, respectively. The genset showed the highest overall cost rate (101.27 USD/h) followed by digester (68.41 USD/h). Furthermore, the net bioelectricity amounted to 67.81% of the overall cost rate of the products, while this value was 32.19% for both liquid and dewatered digestates. According to the results obtained, efforts should mainly focus on enhancing the efficiency of the genset in order to boost the overall performance of the system exergoeconomically. In addition, minimizing the investment-related cost of the digester could also substantially enhance the exergoeconomic performance of the plant.
  19. Papargyropoulou E, Wright N, Lozano R, Steinberger J, Padfield R, Ujang Z
    Waste Manag, 2016 Mar;49:326-336.
    PMID: 26803473 DOI: 10.1016/j.wasman.2016.01.017
    Food waste has significant detrimental economic, environmental and social impacts. The magnitude and complexity of the global food waste problem has brought it to the forefront of the environmental agenda; however, there has been little research on the patterns and drivers of food waste generation, especially outside the household. This is partially due to weaknesses in the methodological approaches used to understand such a complex problem. This paper proposes a novel conceptual framework to identify and explain the patterns and drivers of food waste generation in the hospitality sector, with the aim of identifying food waste prevention measures. This conceptual framework integrates data collection and analysis methods from ethnography and grounded theory, complemented with concepts and tools from industrial ecology for the analysis of quantitative data. A case study of food waste generation at a hotel restaurant in Malaysia is used as an example to illustrate how this conceptual framework can be applied. The conceptual framework links the biophysical and economic flows of food provisioning and waste generation, with the social and cultural practices associated with food preparation and consumption. The case study demonstrates that food waste is intrinsically linked to the way we provision and consume food, the material and socio-cultural context of food consumption and food waste generation. Food provisioning, food consumption and food waste generation should be studied together in order to fully understand how, where and most importantly why food waste is generated. This understanding will then enable to draw detailed, case specific food waste prevention plans addressing the material and socio-economic aspects of food waste generation.
  20. Hannan MA, Arebey M, Begum RA, Basri H, Al Mamun MA
    Waste Manag, 2016 Apr;50:10-9.
    PMID: 26868844 DOI: 10.1016/j.wasman.2016.01.046
    This paper presents a CBIR system to investigate the use of image retrieval with an extracted texture from the image of a bin to detect the bin level. Various similarity distances like Euclidean, Bhattacharyya, Chi-squared, Cosine, and EMD are used with the CBIR system for calculating and comparing the distance between a query image and the images in a database to obtain the highest performance. In this study, the performance metrics is based on two quantitative evaluation criteria. The first one is the average retrieval rate based on the precision-recall graph and the second is the use of F1 measure which is the weighted harmonic mean of precision and recall. In case of feature extraction, texture is used as an image feature for bin level detection system. Various experiments are conducted with different features extraction techniques like Gabor wavelet filter, gray level co-occurrence matrix (GLCM), and gray level aura matrix (GLAM) to identify the level of the bin and its surrounding area. Intensive tests are conducted among 250bin images to assess the accuracy of the proposed feature extraction techniques. The average retrieval rate is used to evaluate the performance of the retrieval system. The result shows that, the EMD distance achieved high accuracy and provides better performance than the other distances.
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links