Displaying publications 1 - 20 of 116 in total

Abstract:
Sort:
  1. Samsuzzaman M, Islam MT, Mandeep JS, Misran N
    ScientificWorldJournal, 2014;2014:804068.
    PMID: 24696661 DOI: 10.1155/2014/804068
    This paper presents a printed wide-slot antenna design and prototyping on available low-cost polymer resin composite material fed by a microstrip line with a rotated square slot for bandwidth enhancement and defected ground structure for gain enhancement. An I-shaped microstrip line is used to excite the square slot. The rotated square slot is embedded in the middle of the ground plane, and its diagonal points are implanted in the middle of the strip line and ground plane. To increase the gain, four L-shaped slots are etched in the ground plane. The measured results show that the proposed structure retains a wide impedance bandwidth of 88.07%, which is 20% better than the reference antenna. The average gain is also increased, which is about 4.17 dBi with a stable radiation pattern in the entire operating band. Moreover, radiation efficiency, input impedance, current distribution, axial ratio, and parametric studies of S11 for different design parameters are also investigated using the finite element method-based simulation software HFSS.
    Matched MeSH terms: Composite Resins/economics; Composite Resins/chemistry*
  2. Lim TW, Tan SK, Li KY, Burrow MF
    J Evid Based Dent Pract, 2023 Dec;23(4):101911.
    PMID: 38035903 DOI: 10.1016/j.jebdp.2023.101911
    OBJECTIVES: The aim of this systematic review was to evaluate the survival and complication rates of resin composite laminate veneers.

    METHODS: Randomized controlled trials and cohort studies with a minimum 2-year follow-up assessing survival and complication rates of resin composite laminate veneers on permanent dentition from 1998 to May 2022. Literature searches were conducted in MEDLINE (PubMed), Scopus, and the Cochrane Central Register of Controlled Trials electronic databases. References cited in the related reviews and included full-text articles were also hand-searched to further identify potentially relevant studies.

    RESULTS: A total of 827 articles were identified. Twenty-two studies were considered for full-text review after the title and abstract screening stage. After exclusion, 7 studies (3 randomized controlled trials and 4 cohort studies) were included in the systematic review. Three published scales were adopted for the quality and risk of bias assessment. At the survival rate threshold, the overall heterogeneity (I2) for randomized controlled trials was 50.5% (P = .108). The overall pooled survival rate of the randomized controlled trials was 88% (95% CI: 81%-94%), with the mean follow-up time ranging from 24 to 97 months. Surface roughness, color mismatch, and marginal discoloration were the most reported complications.

    CONCLUSION: Resin composite laminate veneers demonstrated moderately high survival rates for the entire sample and the direct laminate veneer group demonstrated higher survival rates than the indirect approach. Most of the complications were regarded as clinically acceptable with or without reintervention.

    Matched MeSH terms: Composite Resins*
  3. Darmawati MY, Ismarul N, Fuad Y, Fazan F
    Med J Malaysia, 2004 May;59 Suppl B:27-8.
    PMID: 15468802
    Linear polymers have been commonly used as dental composite. However the aim of this work is to use hyperbranched polymer in an attempt to produce dental composite. The reason is because the dendritic molecules have shown low viscosity at higher molecular weight compared to the linear counterparts. Therefore, this work attempts to substitute the linear polymer with as much of hyperbranched polymer in the dental composite that would pass the required ISO 4049:1998(E) "Dentistry - Resin-based filling material". Several formulations of dental composites were used, i.e. combinations of linear-linear and linear-hyperbranched polymers for comparison. Following this, physical and mechanical characterisation were conducted based on the ISO standards such as water sorption and water solubility. Other characterisation such as polymerisation shrinkage and Vickers hardness were also evaluated. It was found that different types of resins give different physical and mechanical properties. The maximum achievable hyperbranched polymer, which passes the required ISO standard, that can be incorporated in the linear polymer to form dental composite is 43% wt.
    Matched MeSH terms: Composite Resins/standards*
  4. Mustafa AA, Matinlinna JP, Saidin S, Kadir MR
    J Prosthet Dent, 2014 Dec;112(6):1498-506.
    PMID: 24993375 DOI: 10.1016/j.prosdent.2014.05.011
    STATEMENT OF PROBLEM: The inconsistency of dentin bonding affects retention and microleakage.

    PURPOSE: The purpose of this laboratory and finite element analysis study was to investigate the effects on the formation of a hybrid layer of an experimental silane coupling agent containing primer solutions composed of different percentages of hydroxyethyl methacrylate.

    MATERIAL AND METHODS: A total of 125 sound human premolars were restored in vitro. Simple class I cavities were formed on each tooth, followed by the application of different compositions of experimental silane primers (0%, 5%, 25%, and 50% of hydroxyethyl methacrylate), bonding agents, and dental composite resins. Bond strength tests and scanning electron microscopy analyses were performed. The laboratory experimental results were validated with finite element analysis to determine the pattern of stress distribution. Simulations were conducted by placing the restorative composite resin in a premolar tooth by imitating simple class I cavities. The laboratory and finite element analysis data were significantly different from each other, as determined by 1-way ANOVA. A post hoc analysis was conducted on the bond strength data to further clarify the effects of silane primers.

    RESULTS: The strongest bond of hybrid layer (16.96 MPa) was found in the primer with 25% hydroxyethyl methacrylate, suggesting a barely visible hybrid layer barrier. The control specimens without the application of the primer and the primer specimens with no hydroxyethyl methacrylate exhibited the lowest strength values (8.30 MPa and 11.78 MPa) with intermittent and low visibility of the hybrid layer. These results were supported by finite element analysis that suggested an evenly distributed stress on the model with 25% hydroxyethyl methacrylate.

    CONCLUSIONS: Different compositions of experimental silane primers affected the formation of the hybrid layer and its resulting bond strength.

    Matched MeSH terms: Composite Resins/chemistry
  5. Chadda H, Naveen SV, Mohan S, Satapathy BK, Ray AR, Kamarul T
    J Prosthet Dent, 2016 Jul;116(1):129-35.
    PMID: 26873771 DOI: 10.1016/j.prosdent.2015.12.013
    STATEMENT OF PROBLEM: Although the physical and mechanical properties of hydroxyapatite-filled dental restorative composite resins have been examined, the biocompatibility of these materials has not been studied in detail.

    PURPOSE: The purpose of this in vitro study was to analyze the toxicity of acrylate-based restorative composite resins filled with hydroxyapatite and a silica/hydroxyapatite combination.

    MATERIAL AND METHODS: Five different restorative materials based on bisphenol A-glycidyl methacrylate (bis-GMA) and tri-ethylene glycol dimethacrylate (TEGDMA) were developed: unfilled (H0), hydroxyapatite-filled (H30, H50), and silica/hydroxyapatite-filled (SH30, SH50) composite resins. These were tested for in vitro cytotoxicity by using human bone marrow mesenchymal stromal cells. Surface morphology, elemental composition, and functional groups were determined by scanning electron microscopy (SEM), energy-dispersive x-ray spectroscopy (EDX), and Fourier-transformed infrared spectroscopy (FTIR). The spectra normalization, baseline corrections, and peak integration were carried out by OPUS v4.0 software.

    RESULTS: Both in vitro cytotoxicity results and SEM analysis indicated that the composite resins developed were nontoxic and supported cell adherence. Elemental analysis with EDX revealed the presence of carbon, oxygen, calcium, silicon, and gold, while the presence of methacrylate, hydroxyl, and methylene functional groups was confirmed through FTIR analysis.

    CONCLUSIONS: The characterization and compatibility studies showed that these hydroxyapatite-filled and silica/hydroxyapatite-filled bis-GMA/TEGDMA-based restorative composite resins are nontoxic to human bone marrow mesenchymal stromal cells and show a favorable biologic response, making them potential biomaterials.

    Matched MeSH terms: Composite Resins/adverse effects*; Composite Resins/therapeutic use; Composite Resins/chemistry
  6. Jogad N, Patil PG, Gade V, Patil S
    J Prosthet Dent, 2015 Sep;114(3):458-9.
    PMID: 26047801 DOI: 10.1016/j.prosdent.2015.04.005
    Matched MeSH terms: Composite Resins/economics*
  7. Razak AA, Harrison A
    J Prosthet Dent, 1997 Apr;77(4):353-8.
    PMID: 9104710
    Dimensional accuracy of a composite inlay restoration is important to ensure an accurate fit and to minimize cementation stresses.
    Matched MeSH terms: Composite Resins/analysis; Composite Resins/chemistry*
  8. Sulong MZ, Aziz RA
    J Prosthet Dent, 1990 Mar;63(3):342-9.
    PMID: 2407832
    This is a review of the literature concerning wear related to the following materials used in dentistry: dental amalgam, composite resins, and glass-ionomer cements, as well as natural tooth substance. Discussions are included on both in vivo and in vitro studies in which various methods were used to help determine wear resistance.
    Matched MeSH terms: Composite Resins*
  9. Baig MR, Gunaseelan R
    J Oral Implantol, 2012 Apr;38(2):149-53.
    PMID: 20932151 DOI: 10.1563/AAID-JOI-D-09-00089
    Passive fit of a long-span screw-retained implant prosthesis is an important criteria for the success of the restoration. This article describes a technique for fabricating a ceramometal implant fixed dental prosthesis (FDP) for a long-span partially edentulous situation by altering the conventional screw-retained design. The possibility of a passive fit is maximized by intraoral luting of the cast frame to milled abutments, and the potential framework distortion during fabrication is compensated to a major extent. Retrievability is ensured by screw retention of the prosthesis to the implants. Compared with conventional porcelain fused to metal screw-retained FDP, this prosthesis is relatively inexpensive to fabricate.
    Matched MeSH terms: Composite Resins/chemistry
  10. Talib R
    J Nihon Univ Sch Dent, 1993 Sep;35(3):161-70.
    PMID: 8246037
    Dental composite resins are widely used in dental practice and are continually being developed in order to obtain better products. To gain full benefit from these materials, it is important for the clinician to understand their properties. The following is a review of the more common characteristics of composites in current use.
    Matched MeSH terms: Composite Resins/chemistry*
  11. Karimzadeh A, R Koloor SS, Ayatollahi MR, Bushroa AR, Yahya MY
    Sci Rep, 2019 10 31;9(1):15763.
    PMID: 31673118 DOI: 10.1038/s41598-019-51904-4
    This study investigates the capacity of the nano-indentation method in the mechanical characterization of a heterogeneous dental restorative nanocomposite using experimental and computational approaches. In this respect, Filtek Z350 XT was selected as a nano-particle reinforced polymer nanocomposite with a specific range of the particle size (50 nm to 4 µm), within the range of indenter contact area of the nano-indentation experiment. A Sufficient number of nano-indentation tests were performed in various locations of the nanocomposite to extract the hardness and elastic modulus properties. A hybrid computational-experimental approach was developed to examine the extracted properties by linking the internal behaviour and the global response of the nanocomposite. In the computational part, several representative models of the nanocomposite were created in a finite element environment to simulate the mechanism of elastic-plastic deformation of the nanocomposite under Berkovich indenter. Dispersed values of hardness and elastic modulus were obtained through the experiment with 26.8 and 48.5 percent average errors, respectively, in comparison to the nanocomposite properties, respectively. A disordered shape was predicted for plastic deformation of the equilateral indentation mark, representing the interaction of the particles and matrix, which caused the experiment results reflect the local behaviour of the nanocomposite instead of the real material properties.
    Matched MeSH terms: Composite Resins
  12. Baba Musta, Mohamad Md. Tan
    Highly weathered basaltic rock was exposed at PSK profile of Kuantan, Segamat Highway. The weathering profile from fresh rock soil can be observed at PKJ profile at Kg. Jabi Quarry. Twelve rock and soil samples from PSK profile and thirteen samples from PKJ profile have been collected for geochemical analysis. The objective of the analysis is to establish the behaviour of several major and trace elements in the weathering profile of the basaltic rock. The samples were analysed by XRF and XRD techniques. Petrographic study was done on fresh rock samples and concretions. The concentration of major elements (TiO2, Al2O3 and Fe2O3) appear to be increased with the increasing of the degree of weathering whereas the concentration of SiO2 and CaO are decreased. There is a clear correlation between Fe2O3 + Al2O3 with L.O.I as well as between Fe2O3 with Al2O3. Behaviour of the trace elements (Ni, Co, Cr and Zn) against the weathering process are totally different. The secondary minerals (kaolinite, nactire, geothite, hematite and gibbsite) appear to control the behaviour of the major and trace elements.
    Batuan basalt yang terluluhawa sepenuhnya telah dicerap di lokaliti PSK Lebuhraya Segamat-Kuantan. Profil luluhawa yang boleh dilihat perubahan daripada batuan segar hingga tanih didapati di lokaliti PKJ Kuari Kg. Jabi. Dua contoh profil dengan masing-masing 12 sampel dan 13 sample tanih telah dikaji untuk menentukan perlakuan beberapa unsur major dan unsur surih batuan basalt yang terluluhawa. Kaedah analisis yang digunakan ialah pendarflour sinar-X (XRF) dan pembelauan sinar-X (XRF). Kajian petrografi pula dibuat pada sampel batuan segar dan sampel konkresi. Nilai unsur major TiO2, Al2O3 dan Fe2O3 bertambah dengan bertambahnya darjah luluhawa manakala SiO2 dan CaO menyusut. Hubungan korelasi Fe2O3 + Al2O3 dengan L.O.I dan Fe2O3 denagn Al2O3 adalah jelas. Unsur surih nikel (Ni) kobalt (Co), kromium (Cr) dan zink (Zn) mempunyai perlakuan yang berbeza-beza dengan luluhawa. Perlakuan yang ditunjukkan oleh unsur major dan surih tersebut dikawal oleh mineral sekunder (koalinit, nakrit, geotit, hematit dan gibsit).
    Matched MeSH terms: Composite Resins
  13. Umar Hamzah, Abd. Rahim Samsudin
    Identification of a possible source of engineering geological hazard in the limestone area such as cavities, sinkholes and an underground cavern have become necessity for site investigation before any construction of roads, bridges and buildings are carried out. The study is also necessary for tunneling and underground mining works where knowledge of the engineering properties of the rock mass is very important in order to assess the suitability and safety of a proposed building. Geophysical techniques have been widely used in engineering geological study to deal with such problems that normally arise at construction sites with limestone bedrock. In this study, shallow seismic reflection technique and dipole-dipole geoelectrical methods were used to detect the presence of cavity in lime stone area of Batu Cave, Kuala Lumpur. The exact location and depth of cavities in the area were determined from the existing borehole data and report provided by the Geological Survey Department of Malaysia. Based on the borehole data, several cavities that were filled-up with water and fine silt are encountered at depths of 15.7m to 17.8m, 20.2m to 21.1m and 21.4m to 25.7m. Three shallow seismic reflection profiles were established on the cavity area and the results show that the cavities in the limestone occur in the form of 20 to 30m long subterranean channel of 15 to 30 m depth. Dipole-dipole resistivity survey conducted on seismic lines one and three also indicates the presence of the channel and cavities in the limestone.
    Pengecaman punca bencana geologi kejuruteraan di kawasan batu kapur seperti lohong batu kapur, kewujudan lubang benam dan gua-gua batu kapur telah menjadi amat penting dalam penyiasatan tapak sebelum sesuatu pembinaan seperti jalan raya, jambatan dan bangunan dilakukan. Begitu juga dalam kerja-kerja penerowongan dan perlombongan, pengetahuan asas sifat kejuruteraan jasad batuan amat perlu diketahui untuk menitai kesesuaian dan keselamatan bangunan yang bakal dibina. Teknik geofizik telah digunakan secara meluas dalam kajian geologi kejuruteraan untuk menangani masalah yang terdapat di tapak-tapak binaan yang mempunyai batu kapur sebagai batuan dasar. Dalam kajian ini teknik seismos pantulan cetek dan kaedah geoelektrik dwikutub-dwikutub telah digunakan untuk mengesan rongga batu kapur yang terdapat di kawasan Batu Caves, Kuala Lumpur. Kedudukan dan kedalaman rongga batu kapur di kawasan kajian telah ditentukan melalui data lubang gerudi dan laporan yang diperoleh daripada Jabatan Kajibumi Malaysia. Berdasarkan data lubang gerudi tersebut terdapat beberapa rongga yang terisi air dan pasir halus berlodak di kedalaman 15.7 m hingga 17.8 m, 20.2 m hingga 21.1 m dan 21.4 m hingga 25.7 m. Tiga profil seismos pantulan cetek telah dibuat di kawasan berongga tersebut dan hasil survei menunjukkan rongga dalam batu kapur tersebut membentuk palung sepanjang hampir 20 - 30 m pada kedalaman antara 15 m hingga 30 m. Rentisan survei geoelektrik dwikutub yang dilakukan pada profil seismos satu dan tiga juga memperlihatkan kehadiran lohong dan palung dalam batu kapur tersebut.
    Matched MeSH terms: Composite Resins
  14. Shahidan Radiman
    The evolution of microemulsion microstructure formed from didodecyl dimethyl ammonium bromide, water and cyclohexane which started from being structureless (fiat scattering profile) to a mean-field Ginsburg-Landau behaviour is shown. The evolution gave the characteristic Lorentzian scattering profile as the system approaches phase separation.
    Evolusi mikrostruktur mikroemulsi yang terbentuk daripada didodesil dimetil ammonium bromida, air dan sildoheksana tiada berstruktur (profil serakan yang malar) kepada medan-min Ginsburg-Landau. Evolusi tersebut memberikan serakan Lorentz apabila komposisinya menghampiri sempadan pemisahan fasa.
    Matched MeSH terms: Composite Resins
  15. Abdul Rahim Samsuddin, Abdul Ghani Rafek, Umar Hamzah, Suharsono, Khairul Anuar Mohd Nayan
    Analisis spektrum gelombang permukaan (SASW) adalah kaedah seismos yang menggunakan ciri serakan gelombang Rayleigh yang merambat pada lapisan bahan bagi memperolehi profil halaju gelombang ricih. Kaedah SASW merupakan satu kaedah insitu tanpa musnah untuk pencirian tapak geoteknik yang lebih kos efektif berbanding kaedah konvensyenal secara penggerudian. Dalam kajian ini sebanyak 20 stesen yang terdiri daripada 13 tapak kajian telah dipilih. Perisian (WINSASW 2.0) telah digunakan dalam proses penyongsangan untuk menghasilkan profil halaju gelombang ricih melawan kedalaman. Profil-profil ini kemudian dianalisis secara berasingan bagi memperolehi beberapa parameter geologi kejuruteraan jasad batuan seperti kekukuhan, nilai Penanda Mutu Batuan (RQD), anisotropi dan sifat kebolehkorekan. Analisis data SASW dijalankan dengan menganggap bahawa jasad batuan adalah homogen dan isotrop serta mengandungi pelbagai intensiti ketakselanjaran yang mempengaruhi perambatan halaju gelombang permukaan. Pengukuran sifat kedinamikan tanah dijalankan dengan menggunakan halaju gelombang ricih dan nilai ketukan N daripada Ujian Penusukan Piawai (NSPT) dalam lubang gerudi. Satu persamaan linear baharu, Vs = 4.44 NSPT + 213.84 yang mengaitkan halaju gelombang ricih dan NSPT telah diperolehi. Satu persamaan empirik telah dikemukakan bagi mengukur nilai Penanda Mutu Batuan (RQD) berasaskan halaju gelombang ricih yang diperolehi daripada kaedah SASW dan halaju daripada ujian ultrasonik. Persamaan ini memberikan hasil yang perbezaannya kurang daripada 10% berbanding data RQD daripada lubang gerudi. Analisis keanisotropan jasad batuan dijalankan menggunakan halaju gelombang ricih yang diperolehi berdasarkan kaedah SASW yang diukur dalam empat arah. Plot nisbah halaju gelombang ricih - halaju ultrasonik melawan halaju ultrasonik telah digunakan untuk menentukan sifat kebolehkorekan jasad batuan. Sebanyak lima kelas lengkungan kebolehkorekan jasad batuan telah dapat dikemukakan iaitu lengkungan Mudah korek, Mudah koyak, Susah koyak, Pemecah hidraulik dan Peletupan.
    Matched MeSH terms: Composite Resins
  16. Ibrahim Ijang, Mohd Cairul Iqbal Mohd Amin, Bukhori Abu Bakar
    Penggunaan formulasi tablet pelepasan tertahan untuk dadah anti-inflamatori bukan steroid (DAIBS) seperti aspirin berupaya melindungi lapisan perut dari kesan buruk jus asid tubuh. Kajian ini dilakukan untuk menilai keberkesanan formulasi tablet matriks pelepasan tertahan dengan kepelbagaian kepekatan polimer bersama ketoprofen sebagai model. Tablet dibangunkan dengan menggunakan kaedah granulasi basah yang terdiri daripada polimer hidrofilik (hidroksipropil metilselulosa), polimer hidrifobik bersandar pada pH (Eudragit L100-55) dan polimer tak bersandar pada pH (Eudragit R100) sebagai bahan asas pembentukan matriks pada kepekatan 10, 20 dan 30%b/b. Semua formulasi dimampatkan dengan menggunakan mesin pentabletan yang mempunyai penebuk berbentuk cembung bersaiz 10 mm. Tablet yang terhasil diuji daripada segi keseragaman berat, kekerasan, kerapuhan, ketebalan, peratus kandungan dadah dan kajian pelepasan in vitro menggunakan kaedah BP 2007. Hasil menunjukkan kadar pelepasan dadah dikawal oleh jenis dan kepekatan polimer di dalam formulasi matriks. Secara umumnya peningkatan kepekatan kandungan polimer di dalam tablet matriks didapati mengurangkan kadar pelepasan dadah. Perbandingan polimer melalui kepekatan yang sama menggunakan t50%, pula mendapati terdapat perbezaan statistik bermakna (p<0.05) pada kadar pelepasan dadah. Berdasarkan kepada pelepasan dadah dalam kajian in vitro, polimer hidrofobik bersandar pada pH (Eudragit L100-55) menunjukkan profil pelepasan dadah secara tertib sifar yang terbaik berbanding polimer yang lain.
    Matched MeSH terms: Composite Resins
  17. Umar Hamzah, Ibrahim Komoo
    A survey to characterize seismic and ultrasonic properties of a granite weathering profile have been carried out at a roadcut slope exposure along Kuala Lumpur-Karak highway at kilometres 39.9. The terraced cut slope shows a complete weathering profile beginning from fresh grade I rock to grade VI residual soil. Together with in situ seismic measurement, rock samples have been collected for ultrasonic tests in laboratory. The range of velocities representing grades and indices of weathered rocks and soils are determined from the in situ seismic surveys. The range of ultrasonic velocities and elastic moduli are obtained from the laboratory measurements.
    Satu survei untuk mencirikan sifat seismos dan ultrasonik profil luluhawa granit telah dilakukan di singkapan potongan jalan, cerun utara lebuhraya Kuala Lumpur-Karak pada lokaliti 39.9 km. Potongan berteres ini mempamirkan satu profil luluhawa lengkap iaitu mulai batuan gred 1 yang segar hingga ke tanah baki bergred VI. Di samping pengukuran seismos secara in situ, sampel batuan juga diambil untuk dibuat pengukuran halaju ultrasonik di makmal. Julat halaju yang mewakili gred dan indeks luluhawa bagi tanah dan batuan diperolehi daripada survei seismos in situ. Julat halaju trasonik dan modulus kenyal diperolehi hasil pengukuran di makmal.
    Matched MeSH terms: Composite Resins
  18. Zulaikah Mohamed, Nazlina Ibrahim, Ismail Ahmad
    Sains Malaysiana, 2008;37(1):107-113.
    Methanol extract of Melastoma malabathricum leaves inhibited the growth of Staphylococcus aureus and six clinical isolates of Methicilin Resistant Stapyhlococcus aureus (MRSA 1-6). The minimum inhibitory concentration (MIC) of test substance was 1.565mg/ml and the minimum bacteriocidal concentration (MBC) was 3.125 mg/ml. The methanol extract suppressed RNA synthesis at 10 mg/ml as shown by RNA profile which was devoid of three bands compared to the control. Reverse transcriptase-polymerase chain reaction (RT-PCR) analysis using seven primer pairs was only successful in amplifying four cDNA amplicons. The failure to amplify three cDNA amplicons for three primer pairs corresponding to gyrA, femA and nuc genes, implied the possibility of suppression of the corresponding mRNA. Electrophoretic separation of endogenous and exogenuos bacterial proteins showed that three and five protein, respectively were not expressed. One endogenous and three exogenous proteins were over-expressed in treated MRSA compared with untreated control. The results of the molecular and proteomic analyses are in agreement, and based on primers being used, methanol extract of M. malabathricum leaves possibly inhibits MRSA growth through inhibition of DNA synthesis, peptidoglycan production, and nuclease production.
    Keywords: Methicillin resistant Staphylococcus aureus; Melastoma malabathricum; gene expression; protein production
    Matched MeSH terms: Composite Resins
  19. Zal U’yun Wan Mahmood, Che Abd Rahim Mohamed, Zaharudin Ahmad, Abdul Kadir Ishak
    Kajian ini dijalankan untuk melihat variasi taburan 210Po dan 210Pb melalui profil menegak aktivitinya, serta nisbah aktiviti 210Po/210Pb di dalam teras sedimen yang diambil di beberapa stesen persampelan pesisir pantai perairan Sarawak. Didapati profil taburan radionuklid tersebut dalam teras sedimen adalah berubah-ubah mengikut lokasi persampelan dan telah dibuktikan melalui analisis ANOVA yang menunjukkan bahawa terdapat perbezaan bererti pada 95% aras keyakinan bagi aktiviti 210Po (p = 0.000), 210Pb (p = 0.035) dan 210Po/210Pb (p = 0.000) di semua lokasi kajian. Secara umumnya, aktiviti 210Po dan 210Pb yang diukur masing-masing dalam julat 337 ke 2460 Bq/kg, 11 ke 84 Bq/kg di SR 01; 224 ke 2008 Bq/kg, 6 ke 80 Bq/kg di SR 02; 119 ke 1595 Bq/kg, 6 ke 84 Bq/kg di SR 03; 241 ke 2294 Bq/kg, 5 ke 82 Bq/kg di SR 04 dan 175 ke 1340 Bq/kg, 4 ke 44 Bq/kg di SR 05. Merujuk kepada julat tersebut, didapati aktiviti 210Po adalah lebih tinggi daripada aktiviti 210Pb dengan purata nisbah 210Po/210Pb di semua stesen adalah melebihi satu, iaitu dalam julat 20 ke 35. Variasi profil taburan radionuklid tersebut dipercayai dipengaruhi oleh beberapa faktor sekitaran dan telah dibuktikan terdapat korelasi yang kuat di antara taburan radionuklid dengan komposisi sedimen jenis kelodak (210Po:r = 0.701 dan 210Pb: r = 0.648), kedalaman air (210Po: r = -0.647) dan jarak stesen dari daratan (210Po: r = 0.746 dan 210Pb: r = 0.975). Oleh itu, dapat disimpulkan bahawa faktor-faktor tersebut merupakan penyumbang utama ke atas perubahan yang berlaku kepada taburan 210Po dan 210Pb.
    Matched MeSH terms: Composite Resins
  20. Khairiah Badri, Amamer Musbah Redwan
    Fire-retarding polyurethane (PU) composite was produced by adding 2,4-ditert-butylphenyl phosphite (FR) to palm-based monoester resin with loading percentage of 0, 2, 4, and 6 wt%. The Shore D hardness index increased marginally with increasing FR content. However, the impact and flexural strengths decreased with increasing FR loading attributed to the weak interfacial bonding between FR and PU matrix. The fire test indicated lowering of burning rate (from 5.30 mm.s-1 to 2.80 mm.s-1) as the loading percentage of FR increased. The combustion enthalpy of the composites also decreased with higher loading percentage of FR.
    Matched MeSH terms: Composite Resins
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links