This paper describes the synthesis of graphene-based activated carbon from carbonaceous rice straw fly ash in an electrical furnace and the subsequent potassium hydroxide extraction. The produced graphene has a proper morphological structure; flakes and a rough surface can be observed. The average size of the graphene was defined as up to 2000 nm and clarification was provided by high-resolution microscopes (FESEM and FETEM). Crystallinity was confirmed by surface area electron diffraction. The chemical bonding from the graphene was clearly observed, with -C=C- and O-H stretching at peaks of 1644 cm-1 and 3435 cm-1, respectively. Impurities in the graphene were found using X-ray photoelectron spectroscopy and energy dispersive X-ray spectroscopy. The measured size, according to zeta-potential analysis, was 8722.2 ± 25 nm, and the average polydispersity index was 0.576. The stability of the mass reduction was analyzed by a thermogravimetric at 100 °C, with a final reduction of ~ 11%.
The synthesis of nanocomposite with controlled surface morphology plays a key role for pollutant removal from aqueous environments. The influence of the molecular size of the polyelectrolyte in synthesizing silica-iron oxide core-shell nanocomposite with open shell structure was investigated by using dynamic light scattering, atomic force microscopy, and quartz crystal microbalance with dissipation (QCM-D). Here, poly(diallydimethylammonium chloride) (PDDA) was used to promote the attachment of iron oxide nanoparticles (IONPs) onto the silica surface to assemble a nanocomposite with magnetic and catalytic bifunctionality. High molecular weight PDDA tended to adsorb on silica colloid, forming a more extended conformation layer than low molecular weight PDDA. Subsequent attachment of IONPs onto this extended PDDA layer was more randomly distributed, forming isolated islands with open space between them. By taking amoxicillin, an antibiotic commonly found in pharmaceutical waste, as the model system, better removal was observed for silica-iron oxide nanocomposite with a more extended open shell structure.
Silicon dioxide (SiO2) is the most widely used dielectric for electronic applications. It is usually produced by thermal oxidation of silicon or by using a wide range of vacuum-based techniques. By default, the growth of SiO2 by thermal oxidation of silicon requires the use of Si substrates whereas the other deposition techniques either produce low quality or poor interface material and mostly require high deposition or annealing temperatures. Recent investigations therefore have focused on the development of alternative deposition paradigms based on solutions. Here, we report the deposition of SiO2 thin film dielectrics deposited by spray pyrolysis in air at moderate temperatures of ≈350 °C from pentane-2,4-dione solutions of SiCl4. SiO2 dielectrics were investigated by means of UV-vis absorption spectroscopy, spectroscopic ellipsometry, XPS, XRD, UFM/AFM, admittance spectroscopy, and field-effect measurements. Data analysis reveals smooth (RRMS < 1 nm) amorphous films with a dielectric constant of about 3.8, an optical band gap of ≈8.1 eV, leakage current densities in the order of ≈10(-7) A/cm(2) at 1 MV/cm, and high dielectric strength in excess of 5 MV/cm. XPS measurements confirm the SiO2 stoichiometry and FTIR spectra reveal features related to SiO2 only. Thin film transistors implementing spray-coated SiO2 gate dielectrics and C60 and pentacene semiconducting channels exhibit excellent transport characteristics, i.e., negligible hysteresis, low leakage currents, high on/off current modulation ratio on the order of 10(6), and high carrier mobility.
The fabrication tolerance of a short and compact low refractive index grating waveguide polarisation splitter based on the principle of resonant tunnelling was analyzed in this study. The design utilised two grating waveguides with an intermediate conventional waveguide layer. The design and optimisation were conducted using the quasi 2-D effective index solver with global search algorithm. An optimum device operating at 1.55 μm wavelength was obtained at a length of 340 μm. The splitting ratios were calculated to be 36 dB and 15 dB, and the overall device transmission efficiencies, after considering the three-dimensional waveguide leakage loss, were estimated at 88% and 83% for tranverse magnetic and tranverse electric polarisation, respectively.
A new class of liquid crystalline acetylide-imine system was successfully synthesized, characterized
and deposited on indium tin oxide (ITO) coated substrate via electrochemical deposition
method for potential organic film application. The relationship between liquid crystal
molecular structure, phase transition temperature and electrical performance was evaluated.
The mesomorphic properties were identified via polarized optic microscopy (POM) which displayed
fan-shaped texture of smectic A phase and their corresponding transition enthalpies
are in concurrence with DSC and TGA studies. The findings from the conductivity analysis
revealed that the fabricated film exhibits good electrical performance where it displayed
linear current-voltage relationship of I-V curve. Therefore, this proposed type of molecular
framework has given an ideal indication to act as transporting material for application in
optoelectronic devices.
The title compound, 2C14H14N4O·H2O, comprises a neutral mol-ecule containing a central pyrazol-3-one ring flanked by an N-bound phenyl group and a C-bound 5-methyl-1H-pyrazol-3-yl group (at positions adjacent to the carbonyl substituent), its zwitterionic tautomer, whereby the N-bound proton of the central ring is now resident on the pendant ring, and a water mol-ecule of crystallization. Besides systematic variations in geometric parameters, the two independent organic mol-ecules have broadly similar conformations, as seen in the dihedral angle between the five-membered rings [9.72 (9)° for the neutral mol-ecule and 3.32 (9)° for the zwitterionic tautomer] and in the dihedral angles between the central and pendant five-membered rings [28.19 (8) and 20.96 (8)° (neutral mol-ecule); 11.33 (9) and 11.81 (9)°]. In the crystal, pyrazolyl-N-H⋯O(carbon-yl) and pyrazolium-N-H⋯N(pyrazol-yl) hydrogen bonds between the independent organic mol-ecules give rise to non-symmetric nine-membered {⋯HNNH⋯NC3O} and {⋯HNN⋯HNC3O} synthons, which differ in the positions of the N-bound H atoms. These aggregates are connected into a supra-molecular layer in the bc plane by water-O-H⋯N(pyrazolide), water-O-H⋯O(carbon-yl) and pyrazolyl-N-H⋯O(water) hydrogen bonding. The layers are linked into a three-dimensional architecture by methyl-C-H⋯π(phen-yl) inter-actions. The different inter-actions, in particular the weaker contacts, formed by the organic mol-ecules are clearly evident in the calculated Hirshfeld surfaces, and the calculated electrostatic potentials differentiate the tautomers.
The title compound, C13H10N2O2 [also called 1-(pyridin-2-yl)-3-(pyridin-3-yl)propane-1,3-dione], features an almost planar (r.m.s. deviation = 0.0095 Å) central C3O2 core consolidated by an intra-molecular hy-droxy-O-H⋯O(carbon-yl) hydrogen bond. Twists are evident in the mol-ecule, as seen in the dihedral angles between the central core and the 2- and pyridin-3-yl rings of 8.91 (7) and 15.88 (6)°, respectively. The conformation about the C=C bond [1.3931 (17) Å] is Z, and the N atoms lie to the same side of the mol-ecule. In the mol-ecular packing, supra-molecular chains along the a axis are mediated by π(pyridin-2-yl)-π(pyridin-3-yl) inter-actions [inter-centroid distance = 3.7662 (9) Å]. The observation that chains pack with no directional inter-actions between them is consistent with the calculated electrostatic potential, which indicates that repulsive inter-actions dominate.
Solid-oxide fuel cells (SOFCs) are electricity generators that can convert the chemical energy in various fuels directly to the electric power with high efficiency. Recent advances in materials and related key components for SOFCs operating at ≈500 °C are summarized here, with a focus on the materials, structures, and techniques development for low-temperature SOFCs, including the analysis of most of the critical parameters affecting the electrochemical performance of the electrolyte, anode, and cathode. New strategies, such as thin-film deposition, exsolution of nanoparticles from perovskites, microwave plasma heating, and finger-like channeled electrodes, are discussed. These recent developments highlight the need for electrodes with higher activity and electrolytes with greater conductivity to generate a high electrochemical performance at lower temperatures.
Carbon dots (CDs) are a recent addition to the nanocarbon family, encompassing both crystalline and amorphous phases. They have sparked significant research interest due to their unique electrical and optical properties, remarkable biocompatibility, outstanding mechanical characteristics, customizable surface chemistry, and negligible cytotoxicity. Their current applications are mainly limited to flexible photonic and biomedical devices, but they have also garnered attention for their potential use in intelligent packaging. The conversion of food waste into CDs further contributes to the concept of the circular economy. It provides a comprehensive overview of emerging green technologies, energy-saving reactions, and cost-effective starting materials involved in the synthesis of CDs. It also highlights the unique properties of biomass-derived CDs, focusing on their structural performance, cellular toxicity, and functional characteristics. The application of CDs in the food industry, including food packaging, is summarized in a concise manner. This paper sheds light on the current challenges and prospects of utilizing CDs in the packaging industry. It aims to provide researchers with a roadmap to tailor the properties of CDs to suit specific applications in the food industry, particularly in food packaging.
This paper describes how to employ distributed clock gating to achieve an overall low power design of a programmable waveform generator intended for a neural stimulator. The power efficiency is enabled using global timing control combined with local amplitude distribution over a bus to the local stimulator frontends. This allows the combination of local and global clock gating for complete sub-blocks of the design. A counter and a shifter employed at the local digital stimulator reduce the design complexity for the waveform generation and thus the overall power consumptions. The average power results indicate that 63% power can be saved for the global stimulator control unit and 89-96% power can be saved for the local digital stimulator by using the proposed approach. The circuit has been implemented and successfully tested in a 0.35 µm AMS HVCMOS technology.
A modular typed dielectric barrier discharge (DBD) device is designed and tested for air and water remediation. The module is made of a number of DBD tubes that can be arranged in series or parallel. Each of the DBD tubes comprises inner electrode enclosed with dielectric barrier and arranged as such to provide a gap for the passage of gases. Non-thermal plasma generated in the gap effectively creates gaseous chemical reactions. Its efficacy in the remediation of gas stream containing high NOx, similar to diesel emission and wastewater containing latex, are presented. A six tubes DBD module has successfully removed more than 80% of nitric oxide from the gas stream. In another arrangement, oxygen was fed into a two tubes DBD to generate ozone for treatment of wastewater. Samples of wastewater were collected from a treatment pond of a rubber vulcanization pilot plant. The water pollution load was evaluated by the chemical oxygen demand (COD) and biological oxygen demand (BOD5) values. Preliminary results showed some improvement (about 13%) on the COD after treatment and at the same time had increased the BOD5 by 42%. This results in higher BOD5/COD ratio after ozonation which indicate better biodegradability of the wastewater.
Covid-19 has given one positive perspective to look at our planet earth in terms of reducing the air and noise pollution thus improving the environmental conditions globally. This positive outcome of pandemic has given the indication that the future of energy belong to green energy and one of the emerging source of green energy is Lithium-ion batteries (LIBs). LIBs are the backbone of the electric vehicles but there are some major issues faced by the them like poor thermal performance, thermal runaway, fire hazards and faster rate of discharge under low and high temperature environment,. Therefore to overcome these problems most of the researchers have come up with new methods of controlling and maintaining the overall thermal performance of the LIBs. The present review paper mainly is focused on optimization of thermal and structural design parameters of the LIBs under different BTMSs. The optimized BTMS generally demonstrated in this paper are maximum temperature of battery cell, battery pack or battery module, temperature uniformity, maximum or average temperature difference, inlet temperature of coolant, flow velocity, and pressure drop. Whereas the major structural design optimization parameters highlighted in this paper are type of flow channel, number of channels, length of channel, diameter of channel, cell to cell spacing, inlet and outlet plenum angle and arrangement of channels. These optimized parameters investigated under different BTMS heads such as air, PCM (phase change material), mini-channel, heat pipe, and water cooling are reported profoundly in this review article. The data are categorized and the results of the recent studies are summarized for each method. Critical review on use of various optimization algorithms (like ant colony, genetic, particle swarm, response surface, NSGA-II, etc.) for design parameter optimization are presented and categorized for different BTMS to boost their objectives. The single objective optimization techniques helps in obtaining the optimal value of important design parameters related to the thermal performance of battery cooling systems. Finally, multi-objective optimization technique is also discussed to get an idea of how to get the trade-off between the various conflicting parameters of interest such as energy, cost, pressure drop, size, arrangement, etc. which is related to minimization and thermal efficiency/performance of the battery system related to maximization. This review will be very helpful for researchers working with an objective of improving the thermal performance and life span of the LIBs.
The flood that hit Kelantan in December 2014 was the worst in Malaysian history. Women and their infants accounted for a large proportion of the people at risk who were badly affected, as almost half of the population in Kelantan was in the reproductive age group. This report serves to raise awareness that breastfeeding mothers and infants are a special population with unique needs during a disaster. Four of their concerns were identified during this massive flood: first, the negative impact of flood on infant nutritional status and their health; second, open space and lack of privacy for the mothers to breastfeed their babies comfortably at temporary shelters for flood victims; third, uncontrolled donations of infant formula, teats, and feeding bottles that are often received from many sources to promote formula feeding; and lastly, misconceptions related to breastfeeding production and quality that may be affected by the disaster. The susceptibility of women and their infant in a natural disaster enhances the benefits of promoting the breastfeeding rights of women. Women have the right to be supported which enables them to breastfeed. These can be achieved through monitoring the distribution of formula feeding, providing water, electricity and medical care for breastfeeding mothers and their infants. A multifaceted rescue mission team involving various agencies comprising of local government, including the health and nutrition departments, private or non-governmental organizations and individual volunteers have the potential to improve a satisfactory condition of women and infants affected by floods and other potential natural disasters.
Background: Artificial light at night (ALAN) has been linked to increased risk of cancers in body sites like the breast and colorectum. However exposure of ALAN as an environmental risk factor and its relation to cancers in humans has never been studied in detail. Objective: To explore the association of ALAN with all forms of cancers in 158 countries. Materials and Methods: An ecological study encompassing global data was conducted from January to June 2015, with age-standardized rates (ASR) of cancers as the outcome measure. ALAN, in the protected areas, as the exposure variable, was measured with reference to the Protected Area Light Pollution Indicator (PALI) and the Protected Area Human Influence Indicator (PAHI). Pearson’s correlations were calculated for PALI and PAHI with ASR of cancers for 158 countries, adjusted for country populations, electricity consumption, air pollution, and total area covered by forest. Stratified analysis was conducted according to the country income levels. Linear regression was applied to measure the variation in cancers explained by PALI and PAHI. Results: PALI and PAHI were positively associated with ASR of all forms of cancer, and also the four most common cancers (p < 0.05). These positive correlations remained statistically significant for PAHI with all forms of cancer, lung, breast, and colorectal cancer after adjusting for confounders. Positive associations of PALI and PAHI with cancers varied with income level of the individual countries. Variation in all forms of cancers, and the four most common cancers explained by PALI and PAHI, ranged from 3.3 – 35.5%. Conclusion: Artificial light at night is significantly correlated for all forms of cancer as well as lung, breast, colorectal, and prostate cancers individually. Immediate measures should be taken to limit artificial light at night in the main cities around the world and also inside houses.
The aim of the present study was to evaluate the physicochemical and antioxidant properties of Malaysian monofloral honey samples-acacia, pineapple and borneo honey-and compare them with tualang honey. Acacia and pineapple honey are produced by Apis mellifera bees while borneo and tualang honey are produced by Apis cerana and Apis dorsata bees, respectively.
Nanomaterial-based sensors with high sensitivity, fast response and recovery time, large detection range, and high chemical stability are in immense demand for the detection of hazardous gas molecules. Graphene nanoribbons (GNRs) which have exceptional electrical, physical, and chemical properties can fulfil all of these requirements. The detection of gas molecules using gas sensors, particularly in medical diagnostics and safety applications, is receiving particularly high demand. GNRs exhibit remarkable changes in their electrical characteristics when exposed to different gases through molecular adsorption. In this paper, the adsorption effects of the target gas molecules (CO and NO) on the electrical properties of the armchair graphene nanoribbon (AGNR)-based sensor are analytically modelled. Thus, the energy dispersion relation of AGNR is developed considering the molecular adsorption effect using a tight binding (TB) method. The carrier velocity is calculated based on the density of states (DOS) and carrier concentration (n) to obtain I-V characteristics and to monitor its variation in the presence of the gas molecules. Furthermore, the I-V characteristics and energy band structure of the AGNR sensor are simulated using first principle calculations to investigate the gas adsorption effects on these properties. To ensure the accuracy of the proposed model, the I-V characteristics of the AGNR sensor that are simulated based both on the proposed model and first principles calculations are compared, and an acceptable agreement is achieved.
We have further developed the two-brains hypothesis as a form of complementarity (or complementary relationship) of endogenously induced weak magnetic fields in the electromagnetic brain. The locally induced magnetic field between electron magnetic dipole moments of delocalized electron clouds in neuronal domains is complementary to the exogenous electromagnetic waves created by the oscillating molecular dipoles in the electro-ionic brain. In this paper, we mathematically model the operation of the electromagnetic grid, especially in regard to the functional role of atomic orbitals of dipole-bound delocalized electrons. A quantum molecular dynamic approach under quantum equilibrium conditions is taken to illustrate phase differences between quasi-free electrons tethered to an oscillating molecular core. We use a simplified version of the many-body problem to analytically solve the macro-quantum wave equation (equivalent to the Kohn-Sham equation). The resultant solution for the mechanical angular momentum can be used to approximate the molecular orbital of the dipole-bound delocalized electrons. In addition to non-adiabatic motion of the molecular core, 'guidance waves' may contribute to the delocalized macro-quantum wave functions in generating nonlocal phase correlations. The intrinsic magnetic properties of the origins of the endogenous electromagnetic field are considered to be a nested hierarchy of electromagnetic fields that may also include electromagnetic patterns in three-dimensional space. The coupling between the two-brains may involve an 'anticipatory affect' based on the conceptualization of anticipation as potentiality, arising either from the macro-quantum potential energy or from the electrostatic effects of residual charges in the quantum and classical subsystems of the two-brains that occurs through partitioning of the potential energy of the combined quantum molecular dynamic system.
The imminent need for transition to a circular biorefinery using microbial fuel cells (MFC), based on the valorization of renewable resources, will ameliorate the carbon footprint induced by industrialization. MFC catalyzed by bioelectrochemical process drew significant attention initially for its exceptional potential for integrated production of biochemicals and bioenergy. Nonetheless, the associated costly bioproduct production and slow microbial kinetics have constrained its commercialization. This review encompasses the potential and development of macroalgal biomass as a substrate in the MFC system for L-lactic acid (L-LA) and bioelectricity generation. Besides, an insight into the state-of-the-art technological advancement in the MFC system is also deliberated in detail. Investigations in recent years have shown that MFC developed with different anolyte enhances power density from several µW/m2 up to 8160 mW/m2. Further, this review provides a plausible picture of macroalgal-based L-LA and bioelectricity circular biorefinery in the MFC system for future research directions.
The feasibility of preparing activated carbon (JPAC) from jackfruit peel, an industrial residue abundantly available from food manufacturing plants via microwave-assisted NaOH activation was explored. The influences of chemical impregnation ratio, microwave power and radiation time on the properties of activated carbon were investigated. JPAC was examined by pore structural analysis, scanning electron microscopy, Fourier transform infrared spectroscopy, nitrogen adsorption isotherm, elemental analysis, surface acidity/basicity and zeta potential measurements. The adsorptive behavior of JPAC was quantified using methylene blue as model dye compound. The best conditions resulted in JPAC with a monolayer adsorption capacity of 400.06 mg/g and carbon yield of 80.82%. The adsorption data was best fitted to the pseudo-second-order equation, while the adsorption mechanism was well described by the intraparticle diffusion model. The findings revealed the versatility of jackfruit peels as good precursor for preparation of high quality activated carbon.
Single chambered up-flow membrane-less microbial fuel cell (UFML MFC) was developed to study the feasibility of the bioreactor for decolorization of Acid Orange 7 (AO7) and electricity generation simultaneously. The performance of UFML MFC was evaluated in terms of voltage output, chemical oxygen demand (COD) and color removal efficiency by varying the concentration of AO7 in synthetic wastewater. The results shown the voltage generation and COD removal efficiency decreased as the initial AO7 concentration increased; this indicates there is electron competition between anode and azo dye. Furthermore, there was a phenomenon of further decolorization at cathode region which indicates the oxygen and azo dye are both compete as electron acceptor. Based on the UV-visible spectra analysis, the breakdown of the azo bond and naphthalene compound in AO7 were confirmed. These findings show the capability of integrated UFML MFC in azo dye wastewater treatment and simultaneous electricity generation.