Displaying publications 1 - 20 of 118 in total

Abstract:
Sort:
  1. Fulltext 50 MHz-10 GHz low-power resistive feedback current-reuse mixer with inductive peaking for cognitive radio receiver
    Vitee N, Ramiah H, Chong WK, Tan GH, Kanesan J, Reza AW
    ScientificWorldJournal, 2014;2014:683971.
    PMID: 25133252 DOI: 10.1155/2014/683971
    A low-power wideband mixer is designed and implemented in 0.13 µm standard CMOS technology based on resistive feedback current-reuse (RFCR) configuration for the application of cognitive radio receiver. The proposed RFCR architecture incorporates an inductive peaking technique to compensate for gain roll-off at high frequency while enhancing the bandwidth. A complementary current-reuse technique is used between transconductance and IF stages to boost the conversion gain without additional power consumption by reusing the DC bias current of the LO stage. This downconversion double-balanced mixer exhibits a high and flat conversion gain (CG) of 14.9 ± 1.4 dB and a noise figure (NF) better than 12.8 dB. The maximum input 1-dB compression point (P1dB) and maximum input third-order intercept point (IIP3) are -13.6 dBm and -4.5 dBm, respectively, over the desired frequency ranging from 50 MHz to 10 GHz. The proposed circuit operates down to a supply headroom of 1 V with a low-power consumption of 3.5 mW.
    Matched MeSH terms: Electronics/instrumentation*; Electronics/methods
  2. Fulltext A Single Centre Annual Audit on Computed Tomography Pulmonary Angiogram: Demographic, Clinical Scoring System, Patients’ Outcome
    Low Qin Jian, Teo Kuo Zhau, Mohd Nadzri Misni, Cheo Seng Wee
    Borneo Journal of Medical Sciences, 2020;14(2):11-18.
    MyJurnal
    Computed tomography pulmonary angiogram (CTPA) is widely used in the investigation of suspected pulmonary embolism. CTPA is not without adverse effects as it involves intravenous contrast injection and radiation exposure. The annual incidence of pulmonary embolism is 60 – 70 per 100,000 populations and CTPA remains the commonest imaging modality1. This study aims to audit all CTPA performed at Hospital Sultanah Nora Ismail, Batu Pahat, Johor for the entire year of 2018 to illustrate the demographic data, symptoms, risk factors, clinical scoring system applied and patients’ outcome. A retrospective study was conducted to audit all CTPA performed between 1st January to 31st December 2018 via the radiology department electronic records and patients’ records. There were a total of 60 CTPA performed in the entire year of 2018 with 16 positive and 44 negative scans. Among the 16 positive scans, 7 (44%) had a Wells score above 6, 6 (38%) had a Wells score between 2 – 6 and 3 (18%) had a Wells score less than 2. Out of the 16 positive scans, 4 (25%) were known malignancy and 1 was a known case of anti-phospholipid syndrome. All 60 patients had electrographs and arterial blood gases performed prior to CTPA. D dimer was performed in 15 cases (5%). Among the 16 positive scan patients, 4 (25%) passed away during the same admission directly or indirectly related to pulmonary embolism. This annual computed tomography audit report will assist clinicians in making better diagnostic decision when dealing with patients with suspected pulmonary embolism.
    Matched MeSH terms: Electronics
  3. A Comparative Effectiveness Systematic Review and Meta-Analysis of Drugs for the Prophylaxis of Junctional Ectopic Tachycardia
    Mendel B, Christianto, Setiawan M, Prakoso R, Siagian SN
    Curr Cardiol Rev, 2021 Jun 03.
    PMID: 34082685 DOI: 10.2174/1573403X17666210603113430
    BACKGROUND: Junctional ectopic tachycardia (JET) is an arrhythmia originating from the AV junction, which may occur following congenital heart surgery, especially when the intervention is near the atrioventricular junction.

    OBJECTIVE: The aim of this systematic review and meta-analysis is to compare the effectiveness of amiodarone, dexmedetomidine and magnesium in preventing JET following congenital heart surgery.

    METHODS: This meta-analysis was conducted according to the Preferred Reporting Items for Systematic Review and Meta-Analysis (PRISMA) statement, where 11 electronic databases were searched from date of inception to August 2020. The incidence of JET was calculated with the relative risk of 95% confidence interval (CI). Quality assessment of the included studies was assessed using the Consolidated Standards of Reporting Trials (CONSORT) 2010 statement.

    RESULTS: Eleven studies met the predetermined inclusion criteria and were included in this meta-analysis. Amiodarone, dexmedetomidine and magnesium significantly reduced the incidence of postoperative JET [Amiodarone: risk ratio 0.34; I2= 0%; Z=3.66 (P=0.0002); 95% CI 0.19-0.60. Dexmedetomidine: risk ratio 0.34; I2= 0%; Z=4.77 (P<0.00001); 95% CI 0.21-0.52. Magnesium: risk ratio 0.50; I2= 24%; Z=5.08 (P<0.00001); 95% CI 0.39-0.66].

    CONCLUSION: All three drugs show promise in reducing the incidence of JET. Our systematic review found that dexmedetomidine is better in reducing the length of ICU stays as well as mortality. In addition, dexmedetomidine also has the least pronounced side effects among the three. However, it should be noted that this conclusion was derived from studies with small sample sizes. Therefore, dexmedetomidine may be considered as the drug of choice for preventing JET.

    Matched MeSH terms: Electronics
  4. A Recent Digitalization in Recycling Industry Attaining Ecological Sustainability: A Comprehensive Outlook and Future Trend
    Khan SAR, Umar M, Yu Z, Nawaz MT
    Environ Sci Pollut Res Int, 2023 Oct;30(47):103760-103775.
    PMID: 37695483 DOI: 10.1007/s11356-023-29537-y
    The management of waste through dual way of recycling (i-e offline and online) is assumed to have a key role in attaining ecological sustainability and enabling circular practices. The research on online recycling is gaining evolution in recent age. Prior literature on the current research theme has failed to provide a comprehensive outlook and future trend. Therefore, the current research intends to elaborate the current research scenario linked with online recycling by critically scrutinizing the prior research over the last 41 years. A comprehensive analysis was conducted using the Scopus database, retrieving a total of 866 articles. These articles were selected to provide a conceptual overview and understanding of the fundamental research conducted in the field. By employing bibliometric analysis this research provides comprehensive detail about evolution, mapping of publications and prominent trends from the year 1981 to 2022 to understand the practices and future trends of online recycling research. The outcomes elucidated that there is exponential increase in research publications relating to online recycling over the last five years. The most influential producer of online recycling research are China, United Kingdom and United States. Chinese Universities has the highest number of publications among all the countries across globe. Moreover, the current research trend is focused on technology based circular economy, industrial ecology, bio-based waste management, dual channel recycling, municipal waste, waste from electrical and electronic equipment (WEEE), environmental impact and lifecycle assessment. Hence, the prominent research perspective and highlighted features could offer recommendation for upcoming studies to contribute in literature and help practitioners, policymakers and professionals move towards circular practices.
    Matched MeSH terms: Electronics
  5. Fulltext A Review on Graphene-Based Light Emitting Functional Devices
    Junaid M, Md Khir MH, Witjaksono G, Ullah Z, Tansu N, Saheed MSM, et al.
    Molecules, 2020 Sep 14;25(18).
    PMID: 32937975 DOI: 10.3390/molecules25184217
    In recent years, the field of nanophotonics has progressively developed. However, constant demand for the development of new light source still exists at the nanometric scale. Light emissions from graphene-based active materials can provide a leading platform for the development of two dimensional (2-D), flexible, thin, and robust light-emitting sources. The exceptional structure of Dirac's electrons in graphene, massless fermions, and the linear dispersion relationship with ultra-wideband plasmon and tunable surface polarities allows numerous applications in optoelectronics and plasmonics. In this article, we present a comprehensive review of recent developments in graphene-based light-emitting devices. Light emissions from graphene-based devices have been evaluated with different aspects, such as thermal emission, electroluminescence, and plasmons assisted emission. Theoretical investigations, along with experimental demonstration in the development of graphene-based light-emitting devices, have also been reviewed and discussed. Moreover, the graphene-based light-emitting devices are also addressed from the perspective of future applications, such as optical modulators, optical interconnects, and optical sensing. Finally, this review provides a comprehensive discussion on current technological issues and challenges related to the potential applications of emerging graphene-based light-emitting devices.
    Matched MeSH terms: Electronics
  6. Fulltext A Survey on Daily Activity Inclination and Health Complaints among Urban Youth in Malaysia
    Chen AH, Rosli SA, Hovis JK
    J Environ Public Health, 2020;2020:9793425.
    PMID: 33376494 DOI: 10.1155/2020/9793425
    Environmental influence is one of the attributing factors for health status. Chronic interaction with electronic display technology and lack of outdoor activities might lead to health issues. Given the concerns about the digital impact on lifestyle and health challenges, we aimed to investigate the daily activity inclination and health complaints among the Malaysian youth. A self-administered questionnaire covering lifestyle and health challenges was completed by 220 youths aged between 16 and 25. There were a total of 22 questions. Seven questions inspected the patterns of indoor and outdoor activities. Fifteen questions focused on the visual and musculoskeletal symptoms linked to both mental and physical health. The total time spent indoors (15.0 ± 5.4 hours/day) was significantly higher than that spent outdoors (2.5 ± 2.6 hours/day) (t = 39.01, p < 0.05). Total time engrossed in sedentary activities (13.0 ± 4.5 hours/day) was significantly higher than that in nonsedentary activities (4.5 ± 3.8 hours/day) comprised of indoor sports and any outdoor engagements (t = 27.10, p < 0.05). The total time spent on electronic related activities (9.5 ± 3.7 hours/day) was were higher than time spent on printed materials (3.4 ± 1.6 hours/day) (t = 26.01, p < 0.05). The association of sedentary activities was positive in relation to tired eyes (χ2 = 17.58, p < 0.05), sensitivity to bright light (χ2 = 12.10, p < 0.05), and neck pain (χ2 = 17.27, p < 0.05) but negative in relation to lower back pain (χ2 = 8.81, p < 0.05). Our youth spent more time in building and engaged in sedentary activities, predominantly electronic usage. The health-related symptoms, both visual and musculoskeletal symptoms, displayed a positive association with a sedentary lifestyle and a negative association with in-building time.
    Matched MeSH terms: Electronics
  7. Fulltext A biomimetic sensor for the classification of honeys of different floral origin and the detection of adulteration
    Zakaria A, Shakaff AY, Masnan MJ, Ahmad MN, Adom AH, Jaafar MN, et al.
    Sensors (Basel), 2011;11(8):7799-822.
    PMID: 22164046 DOI: 10.3390/s110807799
    The major compounds in honey are carbohydrates such as monosaccharides and disaccharides. The same compounds are found in cane-sugar concentrates. Unfortunately when sugar concentrate is added to honey, laboratory assessments are found to be ineffective in detecting this adulteration. Unlike tracing heavy metals in honey, sugar adulterated honey is much trickier and harder to detect, and traditionally it has been very challenging to come up with a suitable method to prove the presence of adulterants in honey products. This paper proposes a combination of array sensing and multi-modality sensor fusion that can effectively discriminate the samples not only based on the compounds present in the sample but also mimic the way humans perceive flavours and aromas. Conversely, analytical instruments are based on chemical separations which may alter the properties of the volatiles or flavours of a particular honey. The present work is focused on classifying 18 samples of different honeys, sugar syrups and adulterated samples using data fusion of electronic nose (e-nose) and electronic tongue (e-tongue) measurements. Each group of samples was evaluated separately by the e-nose and e-tongue. Principal Component Analysis (PCA) and Linear Discriminant Analysis (LDA) were able to separately discriminate monofloral honey from sugar syrup, and polyfloral honey from sugar and adulterated samples using the e-nose and e-tongue. The e-nose was observed to give better separation compared to e-tongue assessment, particularly when LDA was applied. However, when all samples were combined in one classification analysis, neither PCA nor LDA were able to discriminate between honeys of different floral origins, sugar syrup and adulterated samples. By applying a sensor fusion technique, the classification for the 18 different samples was improved. Significant improvement was observed using PCA, while LDA not only improved the discrimination but also gave better classification. An improvement in performance was also observed using a Probabilistic Neural Network classifier when the e-nose and e-tongue data were fused.
    Matched MeSH terms: Electronics
  8. A current overview of the oxidative desulfurization of fuels utilizing heat and solar light: from materials design to catalysis for clean energy
    Lim XB, Ong WJ
    Nanoscale Horiz, 2021 May 21.
    PMID: 34018529 DOI: 10.1039/d1nh00127b
    The ceaseless increase of pollution cases due to the tremendous consumption of fossil fuels has steered the world towards an environmental crisis and necessitated urgency to curtail noxious sulfur oxide emissions. Since the world is moving toward green chemistry, a fuel desulfurization process driven by clean technology is of paramount significance in the field of environmental remediation. Among the novel desulfurization techniques, the oxidative desulfurization (ODS) process has been intensively studied and is highlighted as the rising star to effectuate sulfur-free fuels due to its mild reaction conditions and remarkable desulfurization performances in the past decade. This critical review emphasizes the latest advances in thermal catalytic ODS and photocatalytic ODS related to the design and synthesis routes of myriad materials. This encompasses the engineering of metal oxides, ionic liquids, deep eutectic solvents, polyoxometalates, metal-organic frameworks, metal-free materials and their hybrids in the customization of advantageous properties in terms of morphology, topography, composition and electronic states. The essential connection between catalyst characteristics and performances in ODS will be critically discussed along with corresponding reaction mechanisms to provide thorough insight for shaping future research directions. The impacts of oxidant type, solvent type, temperature and other pivotal factors on the effectiveness of ODS are outlined. Finally, a summary of confronted challenges and future outlooks in the journey to ODS application is presented.
    Matched MeSH terms: Electronics
  9. A hysteresis-free perovskite transistor with exceptional stability through molecular cross-linking and amine-based surface passivation
    Kim HP, Vasilopoulou M, Ullah H, Bibi S, Ximim Gavim AE, Macedo AG, et al.
    Nanoscale, 2020 Apr 14;12(14):7641-7650.
    PMID: 32207472 DOI: 10.1039/c9nr10745b
    Organo-metal halide perovskite field-effect transistors present serious challenges in terms of device stability and hysteresis in the current-voltage characteristics. Migration of ions located at grain boundaries and surface defects in the perovskite film are the main reasons for instability and hysteresis issues. Here, we introduce a perovskite grain molecular cross-linking approach combined with amine-based surface passivation to address these issues. Molecular cross-linking was achieved through hydrogen bond interactions between perovskite halogens and dangling bonds present at grain boundaries and a hydrophobic cross-linker, namely diethyl-(12-phosphonododecyl)phosphonate, added to the precursor solution. With our approach, we obtained smooth and compact perovskite layers composed of tightly bound grains hence significantly suppressing the generation and migration of ions. Moreover, we achieved efficient surface passivation of the perovskite films upon surface treatment with an amine-bearing polymer, namely polyethylenimine ethoxylated. With our synergistic grain and surface passivation approach, we were able to demonstrate the first perovskite transistor with a complete lack of hysteresis and unprecedented stability upon continuous operation under ambient conditions. Added to the merits are its ambipolar transport of opposite carriers with balanced hole and electron mobilities of 4.02 and 3.35 cm2 V-1 s-1, respectively, its high Ion/Ioff ratio >104 and the lowest sub-threshold swing of 267 mV dec-1 reported to date for any perovskite transistor. These remarkable achievements obtained through a cost-effective molecular cross-linking of grains combined with amine-based surface passivation of the perovskite films open a new era and pave the way for the practical application of perovskite transistors in low-cost electronic circuits.
    Matched MeSH terms: Electronics
  10. Fulltext A longitudinal analysis of injury characteristics among elite and amateur tennis players at different tournaments from electronic newspaper reports
    Musa RM, Hassan I, Abdullah MR, Latiff Azmi MN, Abdul Majeed APP, Abu Osman NA
    Front Public Health, 2022;10:835119.
    PMID: 36033746 DOI: 10.3389/fpubh.2022.835119
    The non-complexity of tennis, coupled with its health benefits, renders it appealing and encourages varying competitions at different levels of age, gender, and expertise. However, the rapid increase in the participation rates witnesses a surge in injury occurrences, prompting the need for in-depth analysis to facilitate immediate intervention. We employed a media content analysis technique in which tennis-associated articles published in the last 5 years were examined. A total of 207 news reports were gathered and screened for analysis. Subsequently, 71 articles were excluded from the study due to content duplications or summary updates of existing news articles, while 23 news articles were also excluded from the study due to inappropriateness. Finally, 113 news reports directly related to injury in tennis were coded and analyzed. We examined various types of injuries reported from the screened articles with respect to their status (fresh, recurrent, and recovery) across expertise levels i.e., elite, or amateur. Similarly, the incidence of injury occurrences based on the types of tournaments the players engage in was also investigated. A chi-square analysis was employed to achieve the objectives of the study. Occurrences of tennis-associated injuries are disseminated across expertise levels [ χ ( 18 ) 2 = 16.542; p = 0.555], with knee, hip, elbow, and shoulder injuries being highly prevalent in both elite and amateur players. Nevertheless, it was noted that elite players suffered a staggering 72.60% of injury-related problems, while amateur players sustained 27.40% of injuries. Moreover, the status of injury spreads based on types of tournaments [ χ ( 4 ) 2 = 3.374; p = 0.497], with higher occurrences of fresh and recurrent injuries, while low recovery rates were observed. The findings further demonstrated that injuries are sustained regardless of tournament types [ χ ( 36 ) 2 = 39.393; p = 0.321]. However, most of the injuries occurred at international tournaments (85%). Whereas, only 5.30% of the injuries occurred at national/regional tournaments while 9.70% were unidentified. It could be deduced from the findings of this investigation that elite players are more prone to injuries compared with amateur players. Furthermore, the most common tennis-related injuries affect the lower, trunk, and upper regions of the body, respectively. A large number of the reported tennis injuries are fresh and recurrent, with a few recoveries. The international tennis tournaments are highly attributed to injury occurrences as opposed to the national/regional tournaments. The application of the media-based data mining technique is non-trivial in projecting injury-related problems that could be used to facilitate the development of an injury index peculiar to the tennis sport for prompt intervention.
    Matched MeSH terms: Electronics
  11. A review of sustainable e-waste generation and management: Present and future perspectives
    Ismail H, Hanafiah MM
    J Environ Manage, 2020 Jun 15;264:110495.
    PMID: 32250915 DOI: 10.1016/j.jenvman.2020.110495
    Studies on sustainable management of waste from electrical and electronic equipment (or e-waste) have gained increasing attention from researchers around the world in recent years, with investigations into various aspects of e-waste management were investigated. Studies on e-waste generation by previous papers have been reviewed to provide an overview of the current research progress and recommendations for future research. The relevant existing studies were collected from various databases. Using content analysis, three main aspects of the existing studies were evaluated: the distribution and trends of the publications, the scope and boundaries of the studies, and the current research practices and research applications. Although there was a significant increasing trend of the amount of research on the evaluation of e-waste generation, however, the number of publications based on the countries of origin was still small. Another limitation was found related to the differences in the selection of research subjects and the level of analysis resulted in variations in the scopes and boundaries of the existing studies. Various other research areas were investigated further based on their research findings, but the analysis of various methodological aspects was complicated due to the increasing number of newly developed methodologies and the lack of comprehensive and up-to-date reviews on this research area. Additionally, there was also a need to evaluate emerging and/or older technology, which led electrical appliances to be overlooked. We found that comprehensive and up-to-date reviews of the methodological aspects of e-waste generation are still lacking. Based on the research gaps and limitations discussed, recommendations for future research were made.
    Matched MeSH terms: Electronics
  12. Fulltext A systematic literature review on technology-enhanced learning in medical education
    May Honey Ohn
    Borneo Journal of Medical Sciences, 2020;14(1):3-17.
    MyJurnal
    This systematic review was aimed to evaluate the effectiveness of technology-enhanced learning (TEL) used in medical teaching for undergraduate medical students. The objectives are to (a) identify various teaching modalities which are used to enhance TEL; (b) evaluate whether TEL is more effective than traditional learning (TL) in cognitive and affective learning domain outcome. The empirical studies were searched in the following databases: Google Scholar, MEDLINE, ERIC, ProQuest, Cochrane Library and Scopus. All papers published from 2008 to 2018 were included. From eligible studies, the study design, study field, study population, intervention methods, type of assessment and learning achievement were abstracted and summarized the information. The search results were independently reviewed by two authors. From a pool of 1384 articles, 43 eligible articles were identified, enrolling 7292 undergraduate medical students examining comparative study between TEL and traditional learning. The results showed that there was a high degree of heterogeneity seen amongst the included studies in terms of TEL modalities used. The majority of intervention studies favoured online resources, while the rest used various offline multimedia electronic devices, virtual simulations and blended modes. Overall findings showed promising data that TEL is better than TL with regards to knowledge gain and skill acquisition, as well as providing higher student satisfaction. In all, the findings present blended learning in a positive and promising light in time, particularly where systematic reviews on technology-enhanced learning in the field of the undergraduate medical programme have produced mixed result.REVIEW ARTICLEA Systematic Literature Review on Technology-Enhanced Learning in Medical EducationMay Honey Ohn1*, Bareth Ravindran2, Chan Zhi Wei3, Khin Maung Ohn4, Ng Pey Luen5Borneo Journal of Medical Sciences 14 (1) January, 2020: 3 – 171 Emergency Department, Sandwell & West Birmingham NHS Trust, United Kingdom2 Surgical Department, Hospital Tuanku Ja’afar Seremban, Kuala Lumpur, Malaysia3 Orthopaedics Department, Hospital Sungai Buloh, Kuala Lumpur, Malaysia4 Department of Surgery, Faculty of Medicine and Health Sciences, Universiti Malaysia Sabah, Kota Kinabalu, Sabah, Malaysia5 Radiology Department, Hospital Queen Elizabeth II, Sabah, Malaysia* Corresponding author’s email: mayhoney.ohn@gmail.com Received: 14 July 2019 Accepted: 5 November 2019Borneo Journal of Medical SciencesBJMSKeywords: blended learning, technology-enhanced learning, medical education, hybrid learning, undergraduate medical students
    Matched MeSH terms: Electronics
  13. Fulltext Absorption study of triangular and rectangular slotted on hollow pyramidal absorber
    Mohamad Faisal Asmadi, Hasnain Abdullah, Mas Izzaty Binti Fazin, Ahmad Rashidy Razali, Mohd Nasir Taib, Azizah Ahmad, et al.
    ESTEEM Academic Journal, 2020;16(2):21-30.
    MyJurnal
    Today, electromagnetic wave theory is commonly used in many engineering devices. However, such devices produce electromagnetic (EM) radiation, damaging people's health and the impact of other electronic device's operation. Therefore, Microwave Absorber has been widely used in anechoic chamber to measure equipment radiation and prevent unwanted radiation and electromagnetic interference. This research investigates the absorption performance of pyramidal absorbers with a slotted method design. This research used rectangular and triangular slotted on the hollow pyramidal absorber. There are six types of slotted: Design 1, Design 2, and Design 3
    which have triangular shapes, and Design 4, Design 5, and Design 6, have rectangular shapes. The pyramidal absorber is produced using CST Microwave Studio Suite. Afterward, the fabrication process is performed using cardboard and coated with Powdered Activated Carbon (PAC). Measurement had been done successfully via far-field measurement using an arch method at 1 GHz to 12 GHz. The slotted pyramidal absorber's absorptivity was taken in each frequency band and was tabulated in figure 10. The result is compared with their maximum absorption in each of the four frequency bands. Comparison based on slot design, triangular and rectangular each had its own advantages at a certain frequency. However, small rectangular slot of Design 1 shows consistent absorption performance at all frequency band.
    Matched MeSH terms: Electronics
  14. Fulltext An 8.72 µW Low-Noise and Wide Bandwidth FEE Design for High-Throughput Pixel-Strip (PS) Sensors
    Jérôme FK, Evariste WT, Bernard EZ, Crespo ML, Cicuttin A, Reaz MBI, et al.
    Sensors (Basel), 2021 Mar 04;21(5).
    PMID: 33806350 DOI: 10.3390/s21051760
    The front-end electronics (FEE) of the Compact Muon Solenoid (CMS) is needed very low power consumption and higher readout bandwidth to match the low power requirement of its Short Strip application-specific integrated circuits (ASIC) (SSA) and to handle a large number of pileup events in the High-Luminosity Large Hadron Collider (LHC). A low-noise, wide bandwidth, and ultra-low power FEE for the pixel-strip sensor of the CMS has been designed and simulated in a 0.35 µm Complementary Metal Oxide Semiconductor (CMOS) process. The design comprises a Charge Sensitive Amplifier (CSA) and a fast Capacitor-Resistor-Resistor-Capacitor (CR-RC) pulse shaper (PS). A compact structure of the CSA circuit has been analyzed and designed for high throughput purposes. Analytical calculations were performed to achieve at least 998 MHz gain bandwidth, and then overcome pileup issue in the High-Luminosity LHC. The spice simulations prove that the circuit can achieve 88 dB dc-gain while exhibiting up to 1 GHz gain-bandwidth product (GBP). The stability of the design was guaranteed with an 82-degree phase margin while 214 ns optimal shaping time was extracted for low-power purposes. The robustness of the design against radiations was performed and the amplitude resolution of the proposed front-end was controlled at 1.87% FWHM (full width half maximum). The circuit has been designed to handle up to 280 fC input charge pulses with 2 pF maximum sensor capacitance. In good agreement with the analytical calculations, simulations outcomes were validated by post-layout simulations results, which provided a baseline gain of 546.56 mV/MeV and 920.66 mV/MeV, respectively, for the CSA and the shaping module while the ENC (Equivalent Noise Charge) of the device was controlled at 37.6 e- at 0 pF with a noise slope of 16.32 e-/pF. Moreover, the proposed circuit dissipates very low power which is only 8.72 µW from a 3.3 V supply and the compact layout occupied just 0.0205 mm2 die area.
    Matched MeSH terms: Electronics
  15. Fulltext An Improved Fabrication Technique for the 3-D Frequency Selective Surface based on Water Transfer Printing Technology
    Harnois M, Himdi M, Yong WY, Rahim SKA, Tekkouk K, Cheval N
    Sci Rep, 2020 Feb 03;10(1):1714.
    PMID: 32015444 DOI: 10.1038/s41598-020-58657-5
    Manufacturing an array of high-quality metallic pattern layers on a dielectric substrate remains a major challenge in the development of flexible and 3-D frequency selective surfaces (FSS). This paper proposes an improved fabrication solution for the 3-D FSS based on water transfer printing (WTP) technology. The main advantages of the proposed solution are its ability to transform complicated 2-D planar FSS patterns into 3-D structures while improving both manufacturing quality and production costs. WTP technology makes use of water surface tension to keep the thin metallic patterns of the proposed FSS floating flat with the absence of a solid planar substrate. This feature enables these metallic FSS patterns to be transferred onto 3-D structures through a dipping process. To test the effectiveness of the proposed technique, the FSS was designed using computer simulation software Microwave Studio to obtain the numerical performance of the FSS structure. The WTP technology was then used to fabricate the proposed FSS prototype before its performance was tested experimentally. The measurement results agreed well with the numerical results, indicating the proposed manufacturing solution would support the development of complicated 3-D electronics devices, such as conformal antenna arrays and metamaterials.
    Matched MeSH terms: Electronics
  16. Fulltext An RF energy harvester system using UHF micropower CMOS rectifier based on a diode connected CMOS transistor
    Shokrani MR, Khoddam M, Hamidon MN, Kamsani NA, Rokhani FZ, Shafie SB
    ScientificWorldJournal, 2014;2014:963709.
    PMID: 24782680 DOI: 10.1155/2014/963709
    This paper presents a new type diode connected MOS transistor to improve CMOS conventional rectifier's performance in RF energy harvester systems for wireless sensor networks in which the circuits are designed in 0.18  μm TSMC CMOS technology. The proposed diode connected MOS transistor uses a new bulk connection which leads to reduction in the threshold voltage and leakage current; therefore, it contributes to increment of the rectifier's output voltage, output current, and efficiency when it is well important in the conventional CMOS rectifiers. The design technique for the rectifiers is explained and a matching network has been proposed to increase the sensitivity of the proposed rectifier. Five-stage rectifier with a matching network is proposed based on the optimization. The simulation results shows 18.2% improvement in the efficiency of the rectifier circuit and increase in sensitivity of RF energy harvester circuit. All circuits are designed in 0.18 μm TSMC CMOS technology.
    Matched MeSH terms: Electronics/methods
  17. An intelligent load shedding scheme using neural networks and neuro-fuzzy
    Haidar AM, Mohamed A, Al-Dabbagh M, Hussain A, Masoum M
    Int J Neural Syst, 2009 Dec;19(6):473-9.
    PMID: 20039470
    Load shedding is some of the essential requirement for maintaining security of modern power systems, particularly in competitive energy markets. This paper proposes an intelligent scheme for fast and accurate load shedding using neural networks for predicting the possible loss of load at the early stage and neuro-fuzzy for determining the amount of load shed in order to avoid a cascading outage. A large scale electrical power system has been considered to validate the performance of the proposed technique in determining the amount of load shed. The proposed techniques can provide tools for improving the reliability and continuity of power supply. This was confirmed by the results obtained in this research of which sample results are given in this paper.
    Matched MeSH terms: Electronics/methods
  18. Fulltext An overview of fractional anisotropy as a reliable quantitative measurement for the corticospinal tract (CST) integrity in correlation with a Fugl-Meyer assessment in stroke rehabilitation
    Zolkefley MKI, Firwana YMS, Hatta HZM, Rowbin C, Nassir CMNCM, Hanafi MH, et al.
    J Phys Ther Sci, 2021 Jan;33(1):75-83.
    PMID: 33519079 DOI: 10.1589/jpts.33.75
    [Purpose] Understanding the essential mechanisms in post-stroke recovery not only provides important basic insights into brain function and plasticity but can also guide the development of new therapeutic approaches for stroke patients. This review aims to give an overview of how various variables of Magnetic Resonance-Diffusion Tensor Imaging (MR-DTI) metrics of fractional anisotropy (FA) can be used as a reliable quantitative measurement and indicator of corticospinal tract (CST) changes, particularly in relation to functional motor outcome correlation with a Fugl-Meyer assessment in stroke rehabilitation. [Methods] PubMed electronic database was searched for the relevant literature, using key words of diffusion tensor imaging (dti), corticospinal tract, and stroke. [Results] We reviewed the role of FA in monitoring CST remodeling and its role of predicting motor recovery after stroke. We also discussed the mechanism of CST remodeling and its modulation from the value of FA and FMA-UE. [Conclusion] Heterogeneity of post-stroke brain disorganization and motor impairment is a recognized challenge in the development of accurate indicators of CST integrity. DTI-based FA measurements offer a reliable and evidence-based indicator for CST integrity that would aid in predicting motor recovery within the context of stroke rehabilitation.
    Matched MeSH terms: Electronics
  19. Fulltext An overview of power electronics applications in fuel cell systems: DC and AC converters
    Ali MS, Kamarudin SK, Masdar MS, Mohamed A
    ScientificWorldJournal, 2014;2014:103709.
    PMID: 25478581 DOI: 10.1155/2014/103709
    Power electronics and fuel cell technologies play an important role in the field of renewable energy. The demand for fuel cells will increase as fuel cells become the main power source for portable applications. In this application, a high-efficiency converter is an essential requirement and a key parameter of the overall system. This is because the size, cost, efficiency, and reliability of the overall system for portable applications primarily depend on the converter. Therefore, the selection of an appropriate converter topology is an important and fundamental aspect of designing a fuel cell system for portable applications as the converter alone plays a major role in determining the overall performance of the system. This paper presents a review of power electronics applications in fuel cell systems, which include various topology combinations of DC converters and AC inverters and which are primarily used in fuel cell systems for portable or stand-alone applications. This paper also reviews the switching techniques used in power conditioning for fuel cell systems. Finally, this paper addresses the current problem encountered with DC converters and AC inverter.
    Matched MeSH terms: Electronics*
  20. Fulltext Analysis of glass-reinforced epoxy material for radio frequency resonator
    Zaman MR, Islam MT, Misran N, Yatim B
    ScientificWorldJournal, 2014;2014:831435.
    PMID: 24977230 DOI: 10.1155/2014/831435
    A radio frequency (RF) resonator using glass-reinforced epoxy material for C and X band is proposed in this paper. Microstrip line technology for RF over glass-reinforced epoxy material is analyzed. Coupling mechanism over RF material and parasitic coupling performance is explained utilizing even and odd mode impedance with relevant equivalent circuit. Babinet's principle is deployed to explicate the circular slot ground plane of the proposed resonator. The resonator is designed over four materials from different backgrounds which are glass-reinforced epoxy, polyester, gallium arsenide (GaAs), and rogers RO 4350B. Parametric studies and optimization algorithm are applied over the geometry of the microstrip resonator to achieve dual band response for C and X band. Resonator behaviors for different materials are concluded and compared for the same structure. The final design is fabricated over glass-reinforced epoxy material. The fabricated resonator shows a maximum directivity of 5.65 dBi and 6.62 dBi at 5.84 GHz and 8.16 GHz, respectively. The lowest resonance response is less than -20 dB for C band and -34 dB for X band. The resonator is prototyped using LPKF (S63) drilling machine to study the material behavior.
    Matched MeSH terms: Electronics/instrumentation*
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links