Central composite design (CCD) and response surface methodology (RSM) were employed to optimize four important variables, i.e. amounts of oil, bacterial inoculum, nitrogen and phosphorus, for the removal of selected n-alkanes during bioremediation of weathered crude oil in coastal sediments using laboratory bioreactors over a 60 day experimentation period. The reactors contained 1 kg soil with different oil, microorganisms and nutrients concentrations. The F Value of 26.89 and the probability value (P < 0.0001) demonstrated significance of the regression model. For crude oil concentration of 2, 16 and 30 g per kg sediments and under optimized conditions, n-alkanes removal was 97.38, 93.14 and 90.21% respectively. Natural attenuation removed 30.07, 25.92 and 23.09% n-alkanes from 2, 16 and 30 g oil/kg sediments respectively. Excessive nutrients addition was found to inhibit bioremediation.
The present study describes the phytoremediation performance of water lettuce (Pistia stratiotes L.) for physicochemical pollutants elimination from paper mill effluent (PME). For this, pot (glass aquarium) experiments were conducted using 0% (BWW: borewell water), 25%, 50%, 75%, and 100% treatments of PME under natural day/light regime. Results of the experiments showed that the highest removal of pH (10.75%), electrical conductivity (EC: 63.82%), total dissolved solids (TDS: 71.20%) biological oxygen demand (BOD: 85.03%), chemical oxygen demand (COD: 80.46%), total Kjeldahl's nitrogen (TKN: 93.03%), phosphorus (P: 85.56%), sodium (Na: 91.89%), potassium (K: 84.04%), calcium (Ca: 84.75%), and magnesium (Mg: 83.62%), most probable number (MPN: 77.63%), and standard plate count (SPC: 74.43%) was noted in 75% treatment of PME after treatment by P. stratiotes. PCA showed the best vector length for TKN, Na, and Ca. The maximum plant growth parameters including, total fresh biomass (81.30 ± 0.28 g), chlorophyll content (3.67 ± 0.05 mg g-1 f.wt), and relative growth rate (0.0051 gg-1 d-1 ) was also measured in 75% PME treatment after phytoremediation experiments. The findings of this study make useful insight into the biological management of PME through plant-based pollutant eradication while leftover biomass may be used as a feedstock for low-cost bioenergy production. PRACTITIONER POINTS: Biological treatment of paper mill effluent using water lettuce is presented. Best reduction of physicochemical and microbiological pollutants was attained in 75% treatment. Maximum production of chlorophyll, plant biomass, and highest growth rate was also observed in 75% treatment.
Rapid economic development and population growth, inadequate infrastructure and expertise, and land scarcity make the management of municipal solid waste become one of Malaysia's most critical environmental issues. The study is aimed at evaluating the generation, characteristics, and management of solid waste in Malaysia based on published information. In general, the per capita generation rate is about 0.5-0.8 kg/person/day in which domestic waste is the primary source. Currently, solid waste is managed by the Ministry of Housing and Local Government, with the participation of the private sector. A new institutional and legislation framework has been structured with the objectives to establish a holistic, integrated, and cost-effective solid waste management system, with an emphasis on environmental protection and public health. Therefore, the hierarchy of solid waste management has given the highest priority to source reduction through 3R, intermediate treatment and final disposal.
Incineration of industrial waste produces large quantities of bottom ash which are normally sent to secured landfill, but is not a sustainable solution. Use of bottom ash in engineering applications will contribute to sustainability and generate revenue. One way of using the industrial waste incineration bottom ash is in controlled low-strength material (CLSM). Use of bottom ash in CLSM has problems related to bleeding and excessive strength development and so an additive has to be used to control bleeding and strength development. The main objective of this research is to study the effect of kaolin addition on the performance of CLSM made using industrial waste incineration bottom ash. CLSM mixes were made with bottom ash, cement, and refined kaolin. Various tests were performed on the CLSM in fresh and hardened states including compressive strength, water absorption, California bearing ratio (CBR) and the tests for concentration of leachable substances on the bleed and leachate. The compressive strength of CLSM tested ranged from 0.11 to 9.86 MPa. CBR values ranged from 6 to 46, and water absorption values from 12 to 36%. It was shown that the addition of kaolin delayed the initial setting time of CLSM mixtures, reduced bleeding, lowered the compressive strength, and increased the values of water absorption, sorption, and initial surface absorption. The CLSM tested did not have corrosivity. It was shown that the hardened CLSM was non hazardous, and the addition of kaolin increased the concentration of heavy metals and salts in the bleed and leachate.
Studies on marine debris have gained worldwide attention since many types of debris have found their way into the food chain of higher organisms. Thus, it is crucial that more focus is given to this area in order to curb contaminations in sea food. This study was conducted to quantify plastic debris buried in sand at selected beaches in Malaysia. Marine debris was identified according to size range and distribution, and this information was related to preventive actions to improve marine waste issues. For the purpose of this study, comparison of plastic waste abundance between a recreational beach and fish-landing beaches was also carried out, since the different beach types represent different activities that produce debris. Six beaches along the Malaysian coastline were selected for this study. The plastic types in this study were related to the functions of the beach. While recreational beaches have abundant quantities of plastic film, foamed plastic including polystyrene, and plastic fragment, fish-landing beaches accumulated line and foamed plastic. A total of 2542 pieces (265.30 g m(-2)) of small plastic debris were collected from all six beaches, with the highest number from Kuala Terengganu, at 879 items m(-2) on Seberang Takir Beach, followed by Batu Burok Beach with 780 items m(-2). Findings from studies of Malaysian beaches have provided a clearer understanding of the distribution of plastic debris. This demonstrates that commitments and actions, such as practices of the 'reduce, reuse, recycle' (3R) approach, supporting public awareness programmes and beach clean-up activities, are essential in order to reduce and prevent plastic debris pollution.
Sonophotocatalysis involves the use of a combination of ultrasonic sound waves, ultraviolet radiation and a semiconductor photocatalyst to enhance a chemical reaction by the formation of free radicals in aqueous systems. Researchers have used sonophotocatalysis in a variety of investigations i.e. from water decontamination to direct pollutant degradation. This degradation process provides an excellent opportunity to reduce reaction time and the amount of reagents used without the need for extreme physical conditions. Given its advantages, the sonophotocatalysis process has a futuristic application from an engineering and fundamental aspect in commercial applications. A detailed search of published reports was done and analyzed in this paper with respect to sonication, photocatalysis and advanced oxidation processes.
Polycyclic aromatic hydrocarbons (PAHs) are hazardous and persistent organic pollutants that usually exist at low concentrations in the environment. In this study, dispersive liquid-liquid microextraction (DLLME) technique coupled with high performance liquid chromatography-fluorescence detection (HPLC-FD) was optimized for the analysis of selected PAHs, namely phenanthrene (PHE), fluoranthene (FLA) and benzo[a]pyrene (BaP) in apple juice. Under the optimal extraction conditions (the mixture of 200 µL of acetone and 50 µL of 1-octanol was applied to extract the selected PAHs for 1 min), the DLLME-HPLC-FD showed excellent linearity over the concentration range of 5 to 200 µg/L for both PHE and FLA, and 0.01 to 5 µg/L for BaP with correlation coefficients, r ≥ 0.9956. The method offered ultra-trace detection of selected PAHs in the range of 0.002 to 0.5 µg/L, and negligible matrix effects in determining selected PAHs with relative recovery average within the range of 92.6 to 109.6% in apple juice. The advantages of applying this method for the extraction of PAHs include rapidity, simple operation, as well as small consumption of organic extraction solvent, which is beneficial for routine analysis.
Methyl orange is one of the anionic dyes and is a major pollutant from textile industry that enters both aquatic and atmospheric systems. In this research, methyl orange was degraded using TiO2 powder and immobilized TiO2 on glass. Titanium tetra-isopropoxide (TTIP) was used for preparation of TiO2 powder using soft chemistry method, and it was immobilized on glass via paste-gel coating method. The prepared photocatalysts were characterized by XRD and SEM. Highly crystalline anatase TiO2 powder photocatalyst was obtained. Meanwhile, immobilized TiO2 was less crystalline and agglomerated onto the glass surface. TiO2 powder had higher degradation rate (71%) compared to immobilized TiO2 (52%) due to its chemical stability and larger amount of photocatalyst contacted with methyl orange during the degradation process.
Fine particulate matter (aerodynamic diameter ≤2.5 μm) (PM2.5) has become a major concern because it can adsorb chemicals e.g. polycyclic aromatic hydrocarbons (PAHs) onto its surface. Although PAHs are priority pollutants that can cause adverse health effect, there is still limited information concerning indoor exposures to PAHs in Malaysia. This study aimed to characterise the distribution of PAHs bounded to PM2.5in primary school environments. Indoor and outdoor PM2.5 were collected between May and July 2017 using low volume samplers (LVS) at three public primary schools in the Federal Territory of Kuala Lumpur. PAHs were extracted by ultrasonic extraction with Dichloromethane: n-Hexane (1:1, v/v) as the extraction solvent and analysed using gas chromatography coupled with mass spectrometer (GC-MS). Based on the results, the average total concentration of PAHs (∑PAHs) ranged from 3.8 to 10.1 ng m-3and 1.6 to 8.0 ng m-3for outdoors and indoors, respectively. PAHs in PM2.5samples indicated the potential contribution of combustion at high temperature and indoor sources and the infiltration of outdoor PAHs were the important sources for outdoor and indoor, respectively. In addition, the diagnostic ratio analysis showed that vehicular emissions were the most predominant sources of PAHs in school environments.
Batik industryiswell known intheEast Coast of Malaysia, particularly in Terengganu and Kelantan. This industry consumes a lot of waterforthe batik making processwhich contributes tohigh dischargeof wastewater containingexcess dye pollutants. Hence,in this study, ananionic clayofnickel/aluminium-layered double hydroxide (NiAL) was investigatedas a potential adsorbent for the removal of anionic dyeof Eriochrome Black T (EBT). The NiAL was synthesized via self-assemblymethod and characterization of NiALwas carried outusing powder X-ray diffraction (PXRD) and Fourier transform infrared spectrophotometer (FTIR). The composition and morphology of NiAL was further analyzed using carbon, hydrogen, nitrogen, sulphur elemental analyzer (CHNS), thermogravimetric analyzer (TGA) and scanning electron microscope (SEM).The potential of NiAL as an adsorbent for the removal ofEBT in aqueous solution was tested at different dosages of NiAL. Theadsorptionabilitywasanalyzedby using two common adsorption isotherms, which were Langmuir and Freundlich models. The adsorption of EBT onto NiAL was governedby Freundlich isotherm model indicating that the adsorption occurs in heterogeneous system.
In this study, Centella asiatica and surface soils were collected from 12 sampling sites in Peninsular Malaysia, and the barium (Ba) concentrations were determined. The Ba concentration [μg/g dry weight (dw)] was 63.72 to 382.01 μg/g in soils while in C. asiatica, Ba concentrations ranged from 5.05 to 21.88 μg/g for roots, 3.31 to 11.22 μg/g for leaves and 2.37 to 6.14 μg/g for stems. In C. asiatica, Ba accumulation was found to be the highest in roots followed by leaves and stems. The correlation coefficients (r) of Ba between plants and soils were found to be significantly positively correlated, with the highest correlation being between roots-soils (r=0.922, p<005), followed by leaves-soils (r=0.890, p<005) and stems-soils (r=0.848, p<005). This indicates that these three parts of C. asiatica are good biomonitors of Ba pollution. For the transplantation study, four sites were selected as unpolluted [(Universiti Putra Malaysia (UPM)], semi-polluted (Seri Kembangan and Balakong) and polluted sites (Juru). Based on the transplantation study under experimental field and laboratory conditions, Ba concentrations in C. asiatica were significantly (p<0.05) higher after three weeks of exposure at Seri Kembangan, Balakong and Juru. Thus, these experimental findings confirm that the leaves, stems and roots of C. asiatica can reflect the Ba levels in the soils where this plant is found. Three weeks after back transplantation to clean soils, the Ba levels in C. asiatica were still higher than the initial Ba level even though Ba elimination occurred. In conclusion, the leaves, stems and roots of C. asiatica are good biomonitors of Ba pollution.
An investigation study was conducted in Bukit Merah Reservoir (BMR) for the assessment of arsenic concentration in the surface sediment in 23 sampling stations. The sediment samples were digested and analysed for arsenic using Inductively Coupled Plasma-Optical Emission Spectrometry (ICP-OES). Sediment parameters such as pH (4.42 ± 0.71), redox potential (121.77 ± 42.45 mV), conductivity (205.7 ± 64.07 μS cm-1) and organic matter (25.35 ± 9.34%) were also examined. The main objectives of this study are to determine the arsenic distribution and concentration and at the same time to assess the enrichment of arsenic using the geoaccumulation index (I geo ) and enrichment factor (EF). This study shows the total arsenic concentration in the surface sediment of BMR is 4.302 ± 2.43 mg kg-1 and found to be below the threshold value of Canadian Interim Sediment Quality Guidelines (ISQG). High arsenic concentration is recorded near the southern part of the lake where anthropogenic activities are prevalent. Based on I geo , 13% of sampling stations are categorised as moderately polluted, 52.2% as unpolluted to moderately polluted and the rest is categorised as unpolluted. EF shows 78.3% stations are classified as extremely high enrichment and the rest as very high enrichment. This finding provides important information on the status of arsenic contamination in BMR and creating awareness concerning the conservation and management of the reservoir in the future.
Cadmium has been classified as an environmental pollutant and human carcinogen. Pectin is a family of complex polysaccharides that function as hydrating agents and cementing materials for the cellulosic network. The aim of this study was to evaluate the protective role of pectin against cadmium-induced testicular toxicity and oxidative stress in rats. Forty male Wistar rats were divided into five equal groups. Groups 1 and 2 were injected intraperitoneally (i.p.) saline (1 mg/kg) and pectin (50 mg/kg), respectively, two days/weeks over three weeks period. Groups 3-5 were injected i.p. with 1 mg/kg cadmium two days/week while groups 4 and 5 co-administrated i.p. with 25 and 50 mg/kg pectin, respectively, three days/week over three weeks period. The results of the present work revealed that cadmium-exposed rats showed decrease in serum testosterone, dehydroepiandrosterone sulfate and lactate dehydrogenase. Testicular cholesterol, total protein, glucose-6-phosphate dehydrogenase, 3β-hydroxysteroid dehydrogenase, superoxide dismutase, glutathione peroxidase, catalase, glutathione S-transferase and reduced glutathione levels were also decreased while testicular malondialdehyde level was increased after cadmium injection. On the other hand, serum luteinizing hormone, follicle stimulating hormone, sex hormone binding globulin and γ-glutamyl transpeptidase were increased after cadmium exposure. Cadmium also induced sperms loss. Co-administration of pectin with cadmium restores all the above parameters and sperms to the normal levels where pectin at higher dose was more effective than lower one. These results were supported by histochemical investigations. In conclusion, pectin can counteract the testicular toxicity and oxidative stress induced by cadmium and the effect was dose-dependent.
Polycyclic aromatic hydrocarbons (PAHs) are persistent pollutants and chemically a class of structurally similar chemical compounds characterized by the presence of fused aromatic rings. This research was undertaken to find out immunotoxic effects produced by pyrene, phenanthrene and fluoranthene. These chemicals were injected into developing chicks at three dose levels (0.2, 2 and 20 mg per kg) through allantioc route to rule out possible mechanisms involved in immunotoxicity. DNA adduct produced by PAHs in immune organs were analyzed by DNA adduct enzyme-linked immunosorbent assay (ELISA) kit and DNA damage was assessed by comet assay. A significant increase in the DNA adduct levels was found in thymus and bursa in 2 mg and 20 mg dose levels of pyrene, fluoranthene and phenanthrene treated groups, whereas those in spleen simulated the value of controls. Comet assay indicated that PAHs especially pyrene, fluoranthene and phenanthrene were capable of inducing increased level of comet parameters in thymus at all the dose levels. Bursa of Fabricius and spleen also showed a gradual rise in comet parameters corresponding to all dose levels, but the increase was more marked as in thymus. Thus, it can be concluded that DNA adducts produced by PAHs lead to single-strand breaks and reduced DNA repair, which ultimately begin a carcinogenic process. Hence, this experiment can be considered as a strong evidence of genotoxic potential of PAHs like pyrene, phenanthrene and fluoranthene in developing chicks.
A cross-sectional study was conducted to investigate the effects of acute and chronic pesticide exposure on the plasma beta-glucuronidase enzyme activity among five patients of acute pesticide poisoning in Tengku Ampuan Rahimah Hospital, Klang, 230 farmers in the MADA area, Kedah and 49 fishermen in Setiu, Terengganu. The duration of pesticide exposure among the patients was unknown, but the plasma samples from patients were collected on day one in the hospital. The duration of pesticide exposure among the farmers was between 1 and 45 years. The beta-glucuronidase activity was compared with plasma cholinesterase activity in the same individual. The plasma cholinesterase activity was measured using Cholinesterase (PTC) Reagent set kit (Teco Diagnostics, UK) based on colorimetric method, while the plasma beta-glucuronidase activity was measured fluorometrically based on beta-glucuronidase assay. The plasma cholinesterase activity was significantly reduced (p<0.05) among the patients (1386.786+/-791.291 U/L/min) but the inhibition in plasma cholinesterase activity among the farmers (7346.5+/-1860.786 U/L/min) was not significant (p>0.05). The plasma beta-glucuronidase activity among the farmers was significantly elevated (p<0.05) (0.737+/-0.425 microM/h) but not significant among the patients (p>0.05). The plasma cholinesterase activity was positively correlated with the plasma beta-glucuronidase activity among the farmers (r=0.205, p<0.01) but not among the patients (r=0.79, p>0.05). Thus, plasma beta-glucuronidase enzyme activity can be measured as a biomarker for the chronic exposure of pesticide. However, further studies need to be performed to confirm whether plasma beta-glucuronidase can be a sensitive biomarker for anticholinesterase pesticide poisoning.
Heavy metals pollution has become a great threat to the world. Since instrumental methods are expensive and need skilled technician, a simple and fast method is needed to determine the presence of heavy metals in the environment. In this study, an inhibitive enzyme assay for heavy metals has been developed using crude proteases from Coriandrum sativum. In this assay, casein was used as a substrate and Coomassie dye was used to denote the completion of casein hydrolysis. In the absence of inhibitors, casein was hydrolysed and the solution became brown, while in the presence of metal ions such as Hg²⁺ and Zn²⁺, the hydrolysis of casein was inhibited and the solution remained blue. Both Hg²⁺ and Zn²⁺ exhibited one-phase binding curve with IC₅₀ values of 3.217 mg/L and 0.727 mg/L, respectively. The limits of detection (LOD) and limits of quantitation (LOQ) for Hg were 0.241 and 0.802 mg/L, respectively, while the LOD and LOQ for Zn were 0.228 and 0.761 mg/L, respectively. The enzyme exhibited broad pH ranges for activity. The crude proteases extracted from Coriandrum sativum showed good potential for the development of a rapid, sensitive, and economic inhibitive assay for the biomonitoring of Hg²⁺ and Zn²⁺ in the aquatic environments.
A variety of trace metals were measured in the egg contents of three clutches of Chelonia mydas collected from Kuala Terengganu state in Peninsular Malaysia. We quantified Mn, Cu, Zn, Se (essential trace metals) and As (anthropogenic pollutant) at several developmental stages obtained by incubating eggs at two different temperatures (27 °C and 31 °C). The incubation temperatures were chosen because they produce predominantly male or predominantly female hatchlings, respectively. The eggs were removed from the sand and washed before being placed in incubators, to ensure that the only possible source of the detected metals was maternal transfer. Other metals: Mo, Co, Ni, Cd, Sn, Sb, Hg, Tl and Pb (all non-essential metals) were detected at concentrations below the lower limit of quantitation (LLOQ). Trace metal concentrations, particularly [Zn], increased during development, other metals (Cu, As, Se and Cr) accumulated to a lesser degree than zinc but no significant differences were observed between the incubation temperatures at any stage of incubation. To date, only a few studies on trace metals in turtle embryos and hatchlings have been reported; this study will provide basic knowledge on the accumulation of trace metals during development at two different incubation temperatures.
Leaf samples of tropical trees, i.e. Dryobalanops lanceolata (Kapur paji), Dipterocarpaceae and Macaranga spp. (Mahang), Euphorbiaceae were analyzed for 21 chemical elements. The pioneer Macaranga spp. exhibited higher concentrations for the majority of elements compared to the emergent species of Dryobalanops lanceolata, which was attributed to the higher physiological activity of the fast growing pioneer species compared to emergent trees. Lead showed rather high concentrations in several samples from the Bakam re-forestation site. This is suggested to be caused by emissions through brick manufacturing and related activities in the vicinity. A comparison of Dryobalanops lanceolata samples collected in 1993, 1995 and 1997 in the Lambir Hills National Park revealed that certain heavy metals, i.e. Co, Cu, Mn, Ni, Pb and Ti showed higher values in 1997 compared to the previous years, which could indicate an atmospheric input from the haze caused by the extensive forest fires raging in Borneo and other parts of Southeast Asia.
A diesel engine running on diesel/biodiesel mixtures containing ethylene glycol diacetate (EGDA) was investigated from the exergoeconomic and exergoenvironmental viewpoints. Biodiesel was mixed with petrodiesel at 5% and 20% volume ratios, and the resultant mixtures were then doped with EGDA at 1-3% volume ratios. The exergetic sustainability indicators of the engine operating on the prepared fuel formulations were determined at varying engine loads. The indicators were selected to support decision-making on fuel composition and engine load following thermodynamic, economic, and environmental considerations. The engine load markedly affected all the studied exergetic parameters. The highest engine exergetic efficiency (39.5%) was obtained for petrodiesel doped with 1 v/v% EGDA at the engine load of 50%. The minimum value of the unit cost of brake power exergy (49.6 US$/GJ) was found for straight petrodiesel at full-load conditions, while the minimum value of the unit environmental impact of brake power exergy (29.9 mPts/GJ) was observed for petrodiesel mixed with 5 v/v% biodiesel at the engine load of 75%. Overall, adding EGDA to fuel mixtures did not favorably influence the outcomes of both exergetic methods due to its energy-intensive and cost-prohibitive production process. In conclusion, although petrodiesel fuel improvers such EGDA used in the present study could properly mitigate pollutant emissions, the adverse effects of such additives on thermodynamic parameters of diesel engines, particularly on exergoeconomic and exergoenvironmental indices, need to be taken into account, and necessary optimizations should be made before their real-world application.