Displaying publications 1 - 20 of 148 in total

Abstract:
Sort:
  1. Investigation of indoor thermal comfort and energy demand in different locations along the sub-Himalayan belt - A simulation based study
    Thapa S, Zaki SA
    J Therm Biol, 2024 Feb;120:103809.
    PMID: 38364574 DOI: 10.1016/j.jtherbio.2024.103809
    The sub-Himalayan region extends over 2500 km, extending over several countries. Though the effects of climate change is widely anticipated in the diverse but fragile ecosystem of the Himalayas, very less research has been conducted on the indoor environment of the buildings in these regions. In this study, a pre-validated model of 3-storey concrete residential building was used to study the indoor performance and thermal comfort in the face of climate change in the 8 (eight) different hill towns (hill stations) located from west to the east. Rise in ambient and indoor conditions were evident as a part of climate change with colder locations being affected the most. The thermal comfort assessment using both the climate chamber based PMV model and adaptive models revealed the decrease in cold related discomfort and increase in hot related discomfort. On an overall, the indoor conditions improved in these cold locations. The indoor and outdoor thermal condition and thermal comfort plummeted significantly with latitude and elevation. The heating demand in the future climate reduced by about 50-70 % in warmer locations, while the cooling demand increased by as much as 1000-2000 % in cold locations, respectively. Additionally, it was seen that the thermal environment and comfort both declined more rapidly with elevation in the locations lying in the western Himalayas as compared to those in the eastern Himalayas.
    Matched MeSH terms: Heating*
  2. Fulltext Electron plasma diagnostics in ELTRAP by electron cyclotron resonance heating method
    Khan F, Ikram M, Rashdan M, Elsayed F, Ahmad P, Khandaker MU
    PLoS One, 2024;19(4):e0296845.
    PMID: 38635742 DOI: 10.1371/journal.pone.0296845
    Electron cyclotron resonance heating method of Particle-in-Cell code was used to analyze heating phenomena, axial kinetic energy, and self-consistent electric field of confined electron plasma in ELTRAP device by hydrogen and helium background gases. The electromagnetic simulations were performed at a constant power of 3.8 V for different RF drives (0.5 GHz- 8 GHz), as well as for 1 GHz constant frequency at these varying amplitudes (1 V-3.8 V). The impacts of axial and radial temperatures were found maximum at 1.8 V and 5 GHz as compared to other amplitudes and frequencies for both background gases. These effects are higher at varying radio frequencies due to more ionization and secondary electrons production and maximum recorded radial temperature for hydrogen background gas was 170.41 eV. The axial kinetic energy impacts were found more effective in the outer radial part (between 0.03 and 0.04 meters) of the ELTRAP device due to applied VRF through C8 electrode. The self-consistent electric field was found higher for helium background gas at 5 GHz RF than other amplitudes and radio frequencies. The excitation and ionization rates were found to be higher along the radial direction (r-axis) than the axial direction (z-axis) in helium background gas as compared to hydrogen background gas. The current studies are advantageous for nuclear physics applications, beam physics, microelectronics, coherent radiation devices and also in magnetrons.
    Matched MeSH terms: Heating
  3. Multiobjective optimization of a cogeneration system based on gas turbine, organic rankine cycle and double-effect absorbtion chiller
    Hai T, Alsubai S, Yahya RO, Gemeay E, Sharma K, Alqahtani A, et al.
    Chemosphere, 2023 Oct;338:139371.
    PMID: 37442387 DOI: 10.1016/j.chemosphere.2023.139371
    Combined cooling, heating and power (CCHP) is one of methods for enhancing the efficiency of the energy conversion systems. In this study a CCHP system consisting of a gas turbin (GT) as the topping cycle, and an organic Rankine cycle (ORC) associated with double-effect absorbtion chiller (DEACH) is decisioned as the bottoming cycle to recover the waste heat from GT exhaust gas. The considered CCHP system is investigated to maintain electricity, heating and cooling demand of a town. A parametric study is investigated and the effect decision variables on the performance indicators including exergy efficiency, total cost rate (TCR), cooling capacity, and ORC power generation is examined. Decision variables of the ORC system consist of HRVG pressure, and condenser pressure and the DEACH including evaporator pressure, condseser pressure, concentration of the concentrated solution, concentration of the weak solution, and solution mass flow rate. Finally a multi-objective optimization performed using Genetic Algorithm (GA) and the optimal design point is selected. It is observed at the optimum point the exergy efficiency, TCR, and sustainability index are 17.56%, 74.49 $/h, and 1.21, respectively.
    Matched MeSH terms: Heating
  4. Design configuration and operational parameters of bi-fluid PVT collectors: an updated review
    Al-Waeli AHA, Sopian K, Kazem HA, Chaichan MT
    Environ Sci Pollut Res Int, 2023 Jul;30(34):81474-81492.
    PMID: 36689112 DOI: 10.1007/s11356-023-25321-0
    The bi-fluid photovoltaic thermal (PVT) collector was introduced to provide more heating options along with improved cooling capabilities for the PV module. Since its introduction, this type of PVT system has been investigated thoroughly in various original works. In this review paper, we intend to put the concept and applications of this technology into question and revise the main achievements and discoveries through research and development with a focus on climatic and operational parameters. The paper encompasses a critical review of the discussed research and future directions for PVT collectors. The main utilized operational modes are discussed in detail, which are (i) water used in both channels, (ii) water in one channel and air in the other, and (iii) air in both channels. The modes were found to lead to different enhancement and performance effects for the utilized photovoltaic modules. The impact of mass flow rate was also taken by keeping one working fluid constant while varying the other to obtain its impact on the energy and exergy efficiency of the collector. In some cases, the fluids were run simultaneously and, in other cases, independently.
    Matched MeSH terms: Heating*
  5. Fulltext Microwave-assisted Preparation of Cross-linked Gelatin-Paracetamol Matrices: Optimization Using the D-optimal Design
    Kuang TK, Kang YB, Segarra I, Kanwal U, Ahsan M, Bukhari NI
    Turk J Pharm Sci, 2021 04 20;18(2):167-175.
    PMID: 33902255 DOI: 10.4274/tjps.galenos.2020.48902
    Objectives: This study was conducted to assess the effect of microwave heating on the preparation of paracetamol cross-linked gelatin matrices by using the design of experiment (DoE) approach and explore the influence of the duration of microwave irradiation, the concentrations of crosslinker, and the amount of sodium bicarbonate (salt) on paracetamol release. These parameters were also compared with those of the matrices prepared via conventional heating.

    Materials and Methods: Twenty gel matrices were prepared with different durations of microwave irradiation, amounts of maize, and concentrations of sodium bicarbonate as suggested by Design Expert (DX®). The percentage drug release, the coefficient of variance (CV) in release, and the mean dissolution time (MDT) were the properties explored in the designed experimentation.

    Results: Target responses were dependent on microwave irradiation time, cross-linker amount, and salt concentration. Classical and microwave heating did not demonstrate statistically significant difference in modifying the percentage of drug released from the matrices. However, the CVs of microwave-assisted formulations were lower than those of the gel matrices prepared via classical heating. Thus, microwave heating produced lesser variations in drug release. The optimized gel matrices demonstrated that the observed percentage of drug release, CV, and MDT were within the prediction interval generated by DX®. The release mechanism of the matrix formulations followed the Peppas-Korsmeyer anomalous transport model.

    Conclusion: The DoE-supported microwave-assisted approach could be applied to optimize the critical factors of drug release with less variation.

    Matched MeSH terms: Heating
  6. Fulltext Offretite Zeolite Single Crystals Synthesized by Amphiphile-Templating Approach
    Ng EP, Ahmad NH, Khoerunnisa F, Mintova S, Ling TC, Daou TJ
    Molecules, 2021 Apr 13;26(8).
    PMID: 33924655 DOI: 10.3390/molecules26082238
    Offretite zeolite synthesis in the presence of cetyltrimethylammonium bromide (CTABr) is reported. The offretite crystals were synthesized with a high crystallinity and hexagonal prismatic shape after only 72 h of hydrothermal treatment at 180 °C. The CTABr has dual-functions during the crystallization of offretite, viz. as structure-directing agent and as mesoporogen. The resulting offretite crystals, with a Si/Al ratio of 4.1, possess more acid sites than the conventional offretite due to their high crystallinity and hierarchical structure. The synthesized offretite is also more reactive than its conventional counterpart in the acylation of 2-methylfuran for biofuel production under non-microwave instant heating condition, giving 83.5% conversion with 100% selectivity to the desired product 2-acetyl-5-methylfuran. Hence, this amphiphile synthesis approach offers another cost-effective and alternative route for crystallizing zeolite materials that require expensive organic templates.
    Matched MeSH terms: Heating
  7. Fulltext Data Assessment on the relationship between typical weather data and electricity consumption of academic building in Melaka
    Ngah Nasaruddin A, Tee BT, Mohd Tahir M, Md Jasman MES
    Data Brief, 2021 Apr;35:106797.
    PMID: 33614870 DOI: 10.1016/j.dib.2021.106797
    Exposure to hot and humid weather conditions will often lead to consuming a vast amount of electricity for cooling. Heating, ventilation, and air conditioning (HVAC) systems are customarily known as the largest consumers of energy in institutions and other facilities which raises the question regarding the impact of the weather conditions to the amount energy consumed. The academic building is a perfect example where a constant fixed daily operating characteristic is measured by the hour, aside from the occasional semester break. Therefore, it can be assumed that the daily HVAC services on an academic facility will operate on a fixed schedule each day, having a similar pattern all year round. This article aims to present an analysis on the relationship between typical weather data by implying the test reference year (TRY) and academic building electricity consumption in an academic building located at Durian Tunggal, Melaka. Typical weather data were generated in representing the weather data between 2010 and 2018 using the Finkelstein-Schafer statistic (F-S statistic) in addition to a data set of electricity consumption. Descriptive analysis and correlation matrix analysis were conducted using JASP software for two sets of sample data; Set A and Set B, with data points of 12 and 108, respectively. The result showed an alternate result with a positive correlation between 1)mean temperature-electricity consumption, and 2)mean rainfall-electricity consumption for data Set A, and a negative correlation between 1)mean temperature-electricity consumption and 2)mean rainfall-electricity consumption for data Set B.
    Matched MeSH terms: Heating
  8. Conversion and transformation of N species during pyrolysis of wood-based panels: A review
    Xu D, Yang L, Zhao M, Zhang J, Syed-Hassan SSA, Sun H, et al.
    Environ Pollut, 2021 Feb 01;270:116120.
    PMID: 33341552 DOI: 10.1016/j.envpol.2020.116120
    Understanding the migration and conversion of nitrogen in wood-based panels (WBPs) during pyrolysis is fundamentally important for potentially transforming the N-containing species into valuable material-based products. This review firstly summarizes the commonly used methods for examining N evolution during the WBPs pyrolysis before probing into the association between the wood and adhesives.The potential effects of wood-adhesive interaction on the pyrolysis process are subsequently analyzed. Furthermore, the controversial statements from literature on the influence of adhesives on wood pyrolysis behavior are discussed, which is followed by the detailed investigation into the distribution and evolution of N-containing species in gas, liquid and char, respectively, during WBPs pyrolysis in recent studies. The differences in N species due to the heating sources (i.e. electrical heating vs microwave heating) are particularly compared. Finally, based on the characteristics of staged pyrolysis, co-pyrolysis and catalytic pyrolysis, the converting pathways for WBPs are proposed with an emphasis on the production of value-added chemicals and carbon materials, simultaneously mitigating NOx emission.
    Matched MeSH terms: Heating
  9. Luminescent polymorphic aggregates of trinuclear Cu(I)-pyrazolate tuned by intertrimeric CuNPy weak coordination bonds
    Zhan SZ, Chen W, Zheng J, Ng SW, Li D
    Dalton Trans, 2021 Jan 18.
    PMID: 33459321 DOI: 10.1039/d0dt03661g
    Five luminescent polymorphic aggregates of trinuclear Cu(i)-pyrazolate, namely [anti-Cu3L3]2 (1), [syn-Cu3L3·C2H5OH]2 (2), [anti-Cu3L3·C2H5OH]n (3), [anti-Cu3L3·0.5C7H8]n (4) and [syn-Cu3L3·C8H10]n (5) (HL = 4-(pyridin-4-ylthio)-3,5-dimethyl-1H-pyrazole), were reported. The trimeric Cu3L3 fragments present syn- and anti-conformations dependent on the dangled direction of 4-pyridyl groups on the two sides of the Cu3Pz3 plane (Pz = pyrazolate). Intertrimeric NPyCu weak coordination bonds associate these Cu3L3 fragments together to form dimeric or polymeric structures, which are further stabilized by crystallized solvent molecules or intertrimeric CuCu interactions. The solvated complexes (3-5) may be transformed into the unsolvated complex 1 by evacuation of the crystallized solvents upon heating. All these complexes emit from green to yellow under UV irradiation, which originated from the triplet excited states of metal to ligand charge transfer (3MLCT) mixed with intertrimeric CuCu interactions. This work provides a novel kind of supramolecular aggregate based on Cu3Pz3 beyond the classical π-acidbase adducts and metallophilicity-dependent dimers/oligomers.
    Matched MeSH terms: Heating
  10. Role of saline concentration during saline-infused radiofrequency ablation: Observation of secondary Joule heating along the saline-tissue interface
    Kho AS, Ooi EH, Foo JJ, Ooi ET
    Comput Biol Med, 2021 01;128:104112.
    PMID: 33212331 DOI: 10.1016/j.compbiomed.2020.104112
    Infusion of saline prior to radiofrequency ablation (RFA) is known to enlarge the thermal coagulation zone. The abundance of ions in saline elevate the electrical conductivity of the saline-saturated region. This promotes greater electric current flow inside the tissue, which increases the amount of RF energy deposition and subsequently enlarges the coagulation zone. In theory, infusion of higher concentration of saline should lead to larger coagulation zone due to the greater number of ions. Nevertheless, existing studies on the effects of concentration on saline-infused RFA have been conflicting, with the exact role of saline concentration yet to be fully elucidated. In this paper, computational models of saline-infused RFA were developed to investigate the role of saline concentration on the outcome of saline-infused RFA. The elevation in tissue electrical conductivity was modelled using the microscopic mixture model, while RFA was modelled using the coupled dual porosity-Joule heating model. Results obtained indicated that the presence of a concentration threshold to which no further elevation in tissue electrical conductivity and enlargement in thermal coagulation can occur. This threshold was determined to be at 15% NaCl. Analysis of the Joule heating distribution revealed the presence of a secondary Joule heating site located along the interface between wet and dry tissue. This secondary Joule heating was responsible for the enlargement in coagulation volume and its rapid growth phase during ablation.
    Matched MeSH terms: Heating
  11. Fulltext A novel and stable way for energy harvesting from Bi2Te3Se alloy based semitransparent photo-thermoelectric module
    Fatima N, Karimov KS, Qasuria TA, Ibrahim MA
    J Alloys Compd, 2020 Dec 30;849:156702.
    PMID: 32834521 DOI: 10.1016/j.jallcom.2020.156702
    In this research, due to the present pandemic of COVID-19, we are proposing a stable and fixed semitransparent photo-thermoelectric cell (PTEC) module for green energy harvesting. This module is based on the alloy of Bismuth Telluride Selenide (Bi2Te3Se), designed in a press tablet form and characterized under solar energy. Here, both aspects of solar energy i.e., light and heat are utilized for both energy production and water heating. The semitransparent PTEC converts heat energy directly to electrical energy due to the gradient of temperature between two electrodes (top and bottom) of thermoelectric cells. The PTEC is 25% transparent, which can be varied according to the necessity of the utilizer. The X-ray diffraction of material and electric characterization of module i.e., open-circuited voltage (VOC) and Seebeck coefficient were performed. The experimental observations disclose that in the proposed PTEC module with an increment in the average temperature (TAvg) from 34 to 60 °C, results in the rise of VOC ∼ 2.4 times. However, by modifying the size of heat-absorbing top electrode and by increasing the temperature gradient through the addition of water coolant under the bottom electrode, an uplift in the champion device results in as increment of VOC ∼5.5 times and Seebeck coefficient obtained was -250 μV/0C, respectively. Results show that not only the selection of material but also the external modifications in the device highly effective the power efficiency of the devices. The proposed modules can generate electric power from light and utilize the penetrating sunlight inside the room and for the heating of the water which also acts as a coolant. These semitransparent thermoelectric cells can be built-in within windows and roofs of buildings and can potentially contribute to green energy harvesting, in situations where movement is restricted locally or globally.
    Matched MeSH terms: Heating
  12. Fulltext Geochemical and organic petrographic characteristics of high bituminous shales from Gurha mine in Rajasthan, NW India
    Singh AK, Hakimi MH, Kumar A, Ahmed A, Abidin NSZ, Kinawy M, et al.
    Sci Rep, 2020 12 17;10(1):22108.
    PMID: 33335176 DOI: 10.1038/s41598-020-78906-x
    A high bituminous shale horizon from the Gurha mine in the Bikaner sub-basin of the Rajasthan District, NW India, was studied using a collection of geochemical and petrological techniques. This study investigated the nature and environmental conditions of the organic matter and its relation to the unconventional oil-shale resources of the bituminous shale. The analyzed shales have high total organic carbon and total sulfur contents, suggesting that these shale sediments were deposited in a paralic environment under reducing conditions. The dominant presence of organic matter derived from phytoplankton algae suggests warm climatic marine environment, with little connection to freshwater enhancing the growth of algae and other microorganisms. The analyzed bituminous shales have high aquatic-derived alginite organic matters, with low Pr/Ph, Pr/n-C17, and Ph/n-C18 ratios. It is classified as Type II oil-prone kerogen, consistent with high hydrogen index value. Considering the maturity indicators of geochemical Tmax (
    Matched MeSH terms: Heating
  13. Fulltext Experimental data on the properties of pelletization of palm kernel shell using sago starch and sodium acetate
    Halim SA, Razali N, Mohd N
    Data Brief, 2020 Dec;33:106535.
    PMID: 34026955 DOI: 10.1016/j.dib.2020.106535
    Pellet mixed with 5 wt% and 10 wt% of binders was tested. The pelleting process was performed using a pellet mill operated at 100 °C and at 50 MPa. The physical and chemical characteristics including hardness, high heating value and proximate analysis of pellet produces were obtained using durometer and through thermographic analysis and the results were reported in this paper. Bulk and unit density were determined according to ASABE standard. The dataset presented here are the data of palm kernel shell pellet prepared using two types of binder; (1) sago starch and (2) sodium acetate. The pelletization of palm kernel shell aimed to increase the density and strength of the palm kernel shell pellet and consequently provide better thermal degradation characteristics.
    Matched MeSH terms: Heating
  14. Effects of honey types and heating treatment on the textural, thermal, microstructural, and chemical properties of glutinous rice flour gels
    Seow EK, Tan TC, Lee LK, Easa AM
    J Texture Stud, 2020 12;51(6):909-916.
    PMID: 32537814 DOI: 10.1111/jtxs.12544
    Hardening issue in starch-based products that arises during storage, is ascribed to the long-term starch retrogradation which involves the recrystallisation of amylopectin. Present study aimed to delay storage hardening with the addition of high diastase honey bee honey (HBH) and low diastase kelulut bee honey (KBH) into glutinous rice flour (GRF) gels. As compared to KBH, retardation of texture deterioration by HBH was more prominent as evidenced by the significantly (p 
    Matched MeSH terms: Heating*
  15. Fulltext An acceleration of microwave-assisted transesterification of palm oil-based methyl ester into trimethylolpropane ester
    Aziz NAM, Yunus R, Hamid HA, Ghassan AAK, Omar R, Rashid U, et al.
    Sci Rep, 2020 11 12;10(1):19652.
    PMID: 33184363 DOI: 10.1038/s41598-020-76775-y
    Microwave-assisted synthesis is known to accelerate the transesterification process and address the issues associated with the conventional thermal process, such as the processing time and the energy input requirement. Herein, the effect of microwave irradiation on the transesterification of palm oil methyl ester (PME) with trimethylolpropane (TMP) was evaluated. The reaction system was investigated through five process parameters, which were reaction temperature, catalyst, time, molar ratio of TMP to PME and vacuum pressure. The yield of TMP triester at 66.9 wt.% and undesirable fatty soap at 17.4% were obtained at 130 °C, 10 mbar, sodium methoxide solution at 0.6 wt.%, 10 min reaction time and molar ratio of TMP to PME at 1:4. The transesterification of palm oil-based methyl ester to trimethylolpropane ester was 3.1 folds faster in the presence of microwave irradiation. The total energy requirement was markedly reduced as compared to the conventional heating method. The findings indicate that microwave-assisted transesterification could probably be an answer to the quest for a cheaper biodegradable biolubricant.
    Matched MeSH terms: Heating
  16. Characterization dataset for pre- and post-irradiated shrimp waste chitosan
    Pati S, Jena P, Shahimi S, Nelson BR, Acharya D, Dash BP, et al.
    Data Brief, 2020 Oct;32:106081.
    PMID: 32775581 DOI: 10.1016/j.dib.2020.106081
    This dataset presents morphological features, elemental composition and functional groups of different pre- and post-gamma (γ)-irradiated chitosan (10kGy & 20kGy) prepared from shrimp waste. The γ-irradiated chitosan was characterized using Fourier transfer infrared (FTIR) spectroscopy and X-ray diffraction (XRD) analyses. Thermogravimetry/differential thermal analysis (TG/DTA) were performed using Perkin Elmer Pyris Diamond DSC with a heating rate of 10 °C/minute and dynamic synthetic atmospheric air set at flow rate of 100 ml/minute. We observed γ-irradiated chitosan to have shorter polymer size, small pores and compacted structure with active alkyl and hydroxyl groups when compared to non-irradiated chitosan. Our data provides baseline understanding for structure of shrimp chitosan after 60Co exposure which means, the biopolymer becomes more stable and is considered suitable for vast food industry applications.
    Matched MeSH terms: Heating
  17. Fulltext Preheated (Heat-Assisted) Clinching Process for Al/CFRP Cross-Tension Specimens
    Lin PC, Fang JC, Lin JW, Tran XV, Ching YC
    Materials (Basel), 2020 Sep 19;13(18).
    PMID: 32961763 DOI: 10.3390/ma13184170
    Effects of processing parameters on preheated (heat-assisted) clinching process to join aluminum alloy 5052-H32 (AA5052) and thermoplastic carbon-fiber-reinforced-plastic (TP-CFRP) sheets for cross-tension (CT) specimens were first studied. Preheating was critical since brittle TP-CFRP could be softened to avoid fracturing or cracking during clinching process. Four processing parameters, including punching force, die depth, heating mode, and heating temperature, were considered. Quasi-static tests and microscope observations were taken to evaluate AA5052/TP-CFRP clinch joints in CT specimens and determine appropriate processing parameters for fatigue tests. Finally, fatigue data and failure mode of clinch joints in CT specimens were obtained and discussed.
    Matched MeSH terms: Heating
  18. Techno-economic analysis of bio-briquette from cashew nut shell waste
    Ifa L, Yani S, Nurjannah N, Darnengsih D, Rusnaenah A, Mel M, et al.
    Heliyon, 2020 Sep;6(9):e05009.
    PMID: 33005808 DOI: 10.1016/j.heliyon.2020.e05009
    The implementation of this research consists of 2 (two) aspects: the making and testing of bio-briquettes called technological aspects and economic analysis called economic aspects. Bio-briquettes is made from cashew nutshell waste obtained from Southeast Sulawesi, Indonesia. It is followed by pyrolysis, which is carried out in a simple batch type reactor by heating using liquefied petroleum gas (LPG). The bio-briquettes product has a calorific value of 29.49 MJ/kg, moisture content of 5.3%, ash content of 4.96%, volatile substances content of 17.16%, and carbon content of 72.62%, which meets the universally accepted bio-briquettes standard (SNI 016235-2000), Japanese, English and ISO 17225. The bio-briquettes product is suitable as an energy source. The economic analysis of the cashew nutshell was analyzed to determine its economic feasibility. For the bio-briquettes production capacity in 2,000 tons/year, cashew nut shell-briquettes products can be sold at 1,052,878 USD/year. The total production cost is USD842,304/year. The net profit is of USD147,402/year. The cost of LPG for 2,000 tons/year production capacity is USD954,358/years. The replacement of LPG with cashew seed bio-briquettes tends to help the average household of Muna Regency community to reduce the annual cost by 37.00%. In conclusion, bio-briquettes production's economic feasibility as analyzed from the investment rate is 23.55%, payout time is 3.42 years, and break-even point is 50.09%.
    Matched MeSH terms: Heating
  19. Low-temperature and long-time heating regimes on non-volatile compound and taste traits of beef assessed by the electronic tongue system
    Ismail I, Hwang YH, Joo ST
    Food Chem, 2020 Aug 01;320:126656.
    PMID: 32224424 DOI: 10.1016/j.foodchem.2020.126656
    The influence of temperature-time combinations on non-volatile compound and taste traits of beef semitendinosus muscles tested by the electronic tongue was studied. Single-stage sous-vide at 60 and 70 °C (6 and 12 h), and two-stage sous-vide that sequentially cooked at 45 °C (3 h) and 60 °C (either 3 or 9 h) were compared with traditional cooking at 70 °C (30 min). Umami was better explained in the given model of partial least squares regression than astringency, sourness, saltiness, bitterness, and richness. Sous-vide at 70 °C for 12 h characterized the most umami, likely adenosine-5'-monophosphate (AMP) and guanosine-5'-monophosphate (GMP) as significant contributors. Two-stage sous-vide projected higher histidine, leucine, inosine, and hypoxanthine with the astringent and sour taste significant after 6 and 12 h cooking, respectively. Equivalent umami concentration (EUC) between umami amino acids and umami nucleotides showed a strong relationship to umami taste assessed by the electronic tongue.
    Matched MeSH terms: Heating
  20. Fulltext MHD radiative nanofluid flow induced by a nonlinear stretching sheet in a porous medium
    Jafar AB, Shafie S, Ullah I
    Heliyon, 2020 Jun;6(6):e04201.
    PMID: 32637680 DOI: 10.1016/j.heliyon.2020.e04201
    In this article, we numerically investigate the influence of thermal radiation and heat generation on the flow of an electrically conducting nanofluid past a nonlinear stretching sheet through a porous medium with frictional heating. The partial differential equations governing the flow problems are reduced to ordinary differential equations via similarity variables. The reduced equations are then solved numerically with the aid of Keller box method. The influence of physical parameters such as nanoparticle volume fraction ϕ, permeability parameter K, nonlinear stretching sheet parameter n, magnetic field parameter M, heat generation parameter Q and Eckert number Ec on the flow field, temperature distribution, skin friction and Nusselt number are studied and presented in graphical illustrations and tabular forms. The results obtained reveal that there is an enhancement in the rate of heat transfer with the rise in nanoparticle volume fraction and permeability parameter. The temperature distribution is also influenced with the presence of K, Q, R and ϕ. This shows that the solid volume fraction of nanoparticle can be used in controlling the behaviours of heat transfer and nanofluid flows.
    Matched MeSH terms: Heating
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links