A lipase catalysed enantioselective hydrolysis process under in situ racemization of the remaining (R)-ibuprofen ester substrate with sodium hydroxide as the catalyst was developed for the production of S-ibuprofen from (R,S)-ibuprofen ester in isooctane. Detailed investigations on parameters study indicated that 0.5 M NaOH, addition of 20% (v/v) co-solvent (dimethyl sulphoxide), operating temperature of 45 degrees C, and 40 mmol/L substrate gave 86% conversion and 99.4% optical purity of S-ibuprofen in dynamic kinetic resolution. Meanwhile, in common enzymatic kinetic resolution process, only 42% conversion of the racemate and 93% enantiomeric excess of the product was obtained which are of lower values as compared to dynamic kinetic resolution. The S-ibuprofen produced during each process was evaluated and approximately 50% increment in concentration of S-acid product was produced when dynamic kinetic resolution was applied into the process.
Increasing demands in palm oil industry hence resulting the production of palm oil to increase. It is then creating a major problem in disposing the waste to be treat in appropriate ways. The governments are forced to look for alternative technology for the palm oil mill effluent (POME) treatment because the demand of oil increases with the awareness on increasing environmental issue. Therefore, a new technology must be found in order to reduce energy consumption, to meet legal requirements on emission and for cost reduction and also increased quality of water treatment. Membrane Anaerobic System (MAS) is a promising alternative way to overcome these issues. In this study, the efficiency of the MAS performance increases to 99.03% in ten days operation. The application of Monod, Contois and Chen & Hashimoto models were used to analyze the performance of MAS for treating POME. The results from the experiment show the substrate removal model is well fits for estimation of kinetics membrane anaerobic system. Amongst them, the Contois and Monod models predicted the bio-kinetic reactions of the MAS very well with coefficient of determination (R2>97%) values. The MAS bioreactor was creating to be an improvement method as well as successful biological treatment since the graph shows linearized which is good agreement with reported in literature.
Earthworms are commonly referred as environmental engineers and their guts are often compared with chemical reactors. However, modeling experiments to substantiate it are lacking. The aim of this study was to use established reactor models, particularly PFR, on the gut of the vermicomposting earthworm Eudrilus eugeniae to understand more on its digestion. To achieve the objective, a mathematical model based on first-order kinetics was framed and used to determine the pattern of digestion rates of nutrient indicators, namely total carbon (%), total nitrogen (%), C/N ratio, 13C (‰), and 15N (‰) at five intersections (pre-intestine, foregut, midgut A, midgut B, and hindgut) along the gut of E. eugeniae. The experimental results revealed that the concentrations of TC, TN, 13C, and 15N decreased during gut transit, whereas C/N ratio increased. The first-order model demonstrated that all the nutrients exhibit a linear pattern of digestion during gut transit, which supports the PFR model. On this basis, the present study concludes that the gut of E. eugeniae functions as PFR.
Clinacanthus nutans is widely grown in tropical Asia and locally known "belalai gajah" or Sabah snake grass. It has been used as a natural product to treat skin rashes, snake bites, lesion caused by herpes, diabetes, fever, and cancer. Therefore, the objectives of this research are to determine the maximum yield and time of exhaustive flavonoids extraction using Peleg's model and to evaluate potential of antiproliferative activity on human lung cancer cell (A549). The extraction process was carried out on fresh and dried leaves at 28 to 30°C with liquid-to-solid ratio of 10 mL/g for 72 hrs. The extracts were collected intermittently analysed using mathematical Peleg's model and RP-HPLC. The highest amount of flavonoids was used to evaluate the inhibitory concentration (IC50) via 2D cell culture of A549. Based on the results obtained, the predicted maximum extract density was observed at 29.20 ± 14.54 hrs of extraction (texhaustive). However, the exhaustive time of extraction to acquire maximum flavonoids content exhibited approximately 10 hrs earlier. Therefore, 18 hrs of extraction time was chosen to acquire high content of flavonoids. The best antiproliferative effect (IC50) on A549 cell line was observed at 138.82 ± 0.60 µg/mL. In conclusion, the flavonoids content in Clinacanthus nutans water extract possesses potential antiproliferative properties against A549, suggesting an alternative approach for cancer treatment.
Poor postharvest handling, microbial infestation, and high respiration rate are some the factors are responsible for poor storage life of perishable commodities. Therefore, effective preservation of these commodities is needed to lower the damages and extend shelf life. Preservation is regarded as the action taken to maintain desired properties of a perishable commodity as long as possible. Persimmon (Diospyros kaki) is perishable fruit with high nutritive value; however, has very short shelf-life. Therefore, effective preservation and drying is needed to extend its storage life. Drying temperature and preservatives significantly influence the quality of perishable vegetables and fruits during drying. The current study investigated the effect of different temperatures and preservatives on drying kinetics and organoleptic quality attributes of persimmon. Persimmon fruits were treated with preservatives (25% honey, 25% aloe vera, 2% sodium benzoate, 1% potassium metabisulfite, and 2% citric acid solutions) under different drying temperatures (40, 45, and 50°C). All observed parameters were significantly affected by individual effects of temperatures and preservatives, except ash contents. Similarly, interactive effects were significant for all parameters except total soluble sugars, ash contents, and vitamin C. Generally, fruits treated with citric acid and dried under 50°C had 8.2% moisture loss hour-1, 14.9 drying hours, 0.030 g H2O g-1 hr-1, 1.23° Brix of total soluble solids, 6.71 pH, 1.35% acidity, and 6.3 mg vitamin C. These values were better than the rest of the preservatives and drying temperatures used in the study. Therefore, treating fruits with citric acid and drying at 50°C was found a promising technique to extend storage life of persimmon fruits. It is recommended that persimmon fruits dried at 50°C and preserved in citric acid can be used for longer storage period.
The thermoalkaline protease enzyme from pitaya (Hylocereus polyrhizus) waste was purified by a factor of 221.2 with 71.3% recovery using ammonium sulphate precipitation, gel filtration, and cation exchange chromatography. Gel filtration chromatography together with sodium dodecyl sulphate gel electrophoresis (SDS-PAGE) revealed that the enzyme is monomeric with a molecular weight of 26.7 kDa. The apparent K m and V max of the protease were 2.8 mg/mL and 31.20 u/min, respectively. The optimum pH and temperature were 8.0 and 70°C. The enzyme was highly active and stable over a wide pH range (from pH 3.0 to pH 11.0 with the optimum activity at pH 8.0). The protease has broad specificity toward azocasein, casein, hemoglobin, and gelatine. Activity of the enzyme was inhibited by Fe(2+) and Zn(2+), while protease activity was increased in the presence of Ca(2+) and Mg(2+) and Cu(2+) by factors of 125%, 110%, and 105%, respectively. The alkaline protease showed extreme stability toward surfactants and oxidizing agent. The purified protease exhibited extreme stability in the presence of organic solvents and inhibitors. In addition, the enzyme was relativity stable toward organic solvents and chelating agents, such as ethylenediaminetetraacetic acid (EDTA). The enzyme, derived from pitaya peel, possesses unique characteristics and could be used in various industrial and biotechnological applications.
Climate change caused by the greenhouse gases CO2 remains a topic of global concern. To mitigate the excessive levels of anthrophonic CO2 in the atmosphere, CO2 capture methods have been developed and among these, adsorption is an especially promising method. This paper presents a series of amine functionalized biochar obtained from desiccated coconut waste (amine-biochar@DCW) for use as CO2 adsorbent. They are ethylenediamine-functionalized biochar@DCW (EDA-biochar@DCW), diethylenetriamine-functionalized biochar@DCW (DETA-biochar@DCW), triethylenetetramine-functionalized biochar@DCW (TETA-biochar@DCW), tetraethylenepentamine-functionalized biochar@DCW (TEPA-biochar@DCW), and pentaethylenehexamine-functionalized biochar@DCW (PEHA-biochar@DCW). The adsorbents were obtained through amine functionalization of biochar and they are characterized using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), energy dispersive X-ray (EDX) spectroscopy, Brunauer-Emmett-Teller (BET), and thermogravimetric analysis (TGA). The CO2 adsorption study was conducted isothermally and using a thermogravimetric analyzer. From the results of the characterization analyses, a series of amine-biochar@DCW adsorbents had larger specific surface area in the range of 16.2 m2/g-37.1 m2/g as compare to surface area of pristine DCW (1.34 m2/g). Furthermore, the results showed an increase in C and N contents as well as the appearance of NH stretching, NH bending, CN stretching, and CN bending, suggesting the presence of amine on the surface of biochar@DCW. The CO2 adsorption experiment shows that among the amine modified biochar adsorbents, TETA-biochar@DCW has the highest CO2 adsorption capacity (61.78 mg/g) when using a mass ratio (m:m) of biochar@DCW:TETA (1:2). The adsorption kinetics on the TETA-biochar@DCW was best fitted by the pseudo-second model (R2 = 0.9998), suggesting the adsorption process occurs through chemisorption. Additionally, TETA-biochar@DCW was found to have high selectivity toward CO2 gas and good reusability even after five CO2 adsorption-desorption cycles. The results demonstrate the potential of novel CO2 adsorbents based on amine functionalized on desiccated coconut waste biochar.
Ethylene gas was introduced into granular cold-water-soluble (GCWS) starches using a solid encapsulation method. The morphological and structural properties of the novel inclusion complexes (ICs) were characterized using scanning electron microscopy, X-ray diffractometry, and Raman spectroscopy. The V-type single helix of GCWS starches was formed through controlled gelatinization and ethanol precipitation and was approved to host ethylene gas. The controlled release characteristics of ICs were also investigated at various temperature and relative humidity conditions. Avrami's equation was fitted to understand the release kinetics and showed that the release of ethylene from the ICs was accelerated by increasing temperature or RH and was decelerated by increased degree of amylose polymerization. The IC of Hylon-7 had the highest ethylene concentration (31.8%, w/w) among the five starches, and the IC of normal potato starch showed the best controlled release characteristics. As a renewable and inexpensive material, GCWS starch is a desirable solid encapsulation matrix with potential in agricultural and food applications.
In this work, graphene oxide (GO) and its reduced graphene oxide-zinc oxide nanocomposite (rGO-ZnO) was used for the removal of Cr (VI) from aqueous medium. By employing a variety of characterization techniques, morphological and structural properties of the adsorbents were determined. The adsorption study was done by varying concentration, temperature, pH, time, and amount of adsorbent. The results obtained confirmed that rGO-ZnO is a more economical and promising adsorbent for removing Cr (VI) as compared to GO. Kinetic study was also performed, which suggested that sorption of Cr (VI) follows the pseudo-first-order model. For equilibrium study, non-linear Langmuir was found a better fitted model than its linearized form. The maximum adsorption capacity calculated for GO and rGO-ZnO nanocomposite were 19.49 mg/g and 25.45 mg/g, respectively. Endothermic and spontaneous nature of adsorption was detected with positive values of ΔS (change in entropy), which reflects the structural changes happening at the liquid/solid interface.
Herein, it was aimed to optimize, model, and forecast the biosorption of Congo Red onto biomass-derived biosorbent. Therefore, the waste-orange-peels were processed to fabricate biomass-derived carbon, which was activated by ZnCl2 and modified with cetyltrimethylammonium bromide. The physicochemical properties of the biosorbents were explored by scanning electron microscopy and N2 adsorption/desorption isotherms. The effects of pH, initial dye concentration, temperature, and contact duration on the biosorption capacity were investigated and optimized by batch experimental process, followed by the kinetics, equilibrium, and thermodynamics of biosorption were modeled. Furthermore, various artificial neural network (ANN) architectures were applied to experimental data to optimize the ANN model. The kinetic modeling of the biosorption offered that biosorption was in accordance both with the pseudo-second-order and saturation-type kinetic model, and the monolayer biosorption capacity was calculated as 666.67 mg g-1 at 25 °C according to Langmuir isotherm model. According to equilibrium modeling, the Freundlich isotherm model was better fitted to the experimental data than the Langmuir isotherm model. Moreover, the thermodynamic modeling revealed biosorption took place spontaneously as an exothermic process. The findings revealed that the best ANN architecture trained with trainlm as the backpropagation algorithm, with tansig-purelin transfer functions, and 14 neurons in the single hidden layer with the highest coefficient of determination (R2 = 0.9996) and the lowest mean-squared-error (MSE = 0.0002). The well-agreement between the experimental and ANN-forecasted data demonstrated that the optimized ANN model can predict the behavior of the anionic dye biosorption onto biomass-derived modified carbon materials under various operation conditions.
α-Glucosidase inhibitors (AGIs) are used as medicines for the treatment of diabetes mellitus. The α-Glucosidase enzyme is present in the small intestine and is responsible for the breakdown of carbohydrates into sugars. The process results in an increase in blood sugar levels. AGIs slow down the digestion of carbohydrates that is helpful in controlling the sugar levels in the blood after meals. Among heterocyclic compounds, benzimidazole moiety is recognized as a potent bioactive scaffold for its wide range of biologically active derivatives. The aim of this study is to explore the α-glucosidase inhibition ability of benzimidazolium salts. In this study, two novel series of benzimidazolium salts, i.e., 1-benzyl-3-{2-(substituted) amino-2-oxoethyl}-1H-benzo[d]imidazol-3-ium bromide 9a-m and 1-benzyl-3-{2-substituted) amino-2-oxoethyl}-2-methyl-1H-benzo[d] imidazol-3-ium bromide 10a-m were screened for their in vitro α-glucosidase inhibitory potential. These compounds were synthesized through a multistep procedure and were characterized by 1H-NMR, 13C-NMR, and EI-MS techniques. Compound 10d was identified as the potent α-glucosidase inhibitor among the series with an IC50 value of 14 ± 0.013 μM, which is 4-fold higher than the standard drug, acarbose. In addition, compounds 10a, 10e, 10h, 10g, 10k, 10l, and 10m also exhibited pronounced potential for α-glucosidase inhibition with IC50 value ranging from 15 ± 0.037 to 32.27 ± 0.050 µM when compared with the reference drug acarbose (IC50 = 58.8 ± 0.12 μM). A molecular docking study was performed to rationalize the binding interactions of potent inhibitors with the active site of the α-glucosidase enzyme.
Bacterial strains belonging to Citrobacter spp. were reported to produce polysaccharides consisting of N-acetylglucosamine and glucosamine like chitosan, with high flocculation activity. In this work, the flocculation dewatering performance of activated sludge conditioned by a novel cationic chitosan-like bioflocculant (BF) named BF01314, produced from Citrobacter youngae GTC 01314, was evaluated under the influences of flocculant dosage, pH, and temperature. At BF dosage as low as 0.5 kg/t DS, the sludge dewaterability was significantly enhanced in comparison to the raw (untreated) sludge, featuring well-flocculated characteristic (reduction in CST from 22.0 s to 9.4 s) and good sludge filterability with reduced resistance (reduction in SRF by one order from 7.42 × 1011 to 9.59 × 1010 m/kg) and increased compactness of sludge (increase in CSC from 15.2 to 23.2%). Besides, the BF demonstrated comparable high sludge dewatering performance within the pH range between 2 and 8, and temperature range between 25 °C and 80 °C. Comparison between the BF, the pristine chitosan and the commercial cationic copolymer MF 7861 demonstrated equivalent performance with enhanced dewaterability at the dosage between 2.0 and 3.0 kg/t DS. Besides, the BF demonstrated strong flocculation activity (>99%) when added to the sludge suspension using moderate to high flocculation speeds (100-200 rpm) with at least 3-min mixing time. The BF's reaction in sludge flocculation was best fitted with a pseudo first-order kinetic model. Electrostatic charge patching and polymer bridging mechanisms are believed to be the dominant mechanistic phenomena during the BF's sludge conditioning process (coagulation-flocculation).
Elevated levels of nutrients in agroindustry wastewaters, and higher reliance on chlorination pose health threats due to formation of chlorinated organics as well as increased chlorination costs. Removals of ammonium and nitrate compounds were studied using activated carbon from palm shells, as adsorbent and support media. Experiments were carried out at several loadings, F:M from 0.31 to 0.58, and hydraulic residence times (HRT) of 24 h, 12 h and 8 h. Results show that the wastewater treatment process achieved removals of over 90% for COD and 62% for Total-N. Studies on removals from river water were carried out in sequencing batch reactor (SBR) and activated carbon biofilm (ACB) reactor. Removals achieved by the SBR adsorption-biodegradation combination were 67.0% for COD, 58.8% for NH3-N and 25.5% for NO3-N while for adsorption alone the removals were only 37.0% for COD, 35.2% for NH3-N and 13.8% for NO3-N. In the ACB reactor, at HRT of 1.5 to 6 h, removals ranged from 12.5 to 100% for COD, 16.7 to 100% for NO3-N and 13.5 to 100% for NH3-N. Significant decrease in removals was shown at lower HRT. The studies have shown that substantial removals of COD, NO3-N and NH3-N from both wastewater and river water may be achieved via adsorption-biodegradation by biofilm on activated carbon processes.
The current status of silver nanoparticles (AgNPs) in the water environment in Malaysia was examined and reported. For inspection, two rivers and two sewage treatment plants (STPs) were selected. Two activated carbons derived from oil palm (ACfOPS) and coconut (ACfCS) shells were proposed as the adsorbent to remove AgNPs. It was found that the concentrations of AgNPs in the rivers and STPs are in the ranges of 0.13 to 10.16 mg L-1 and 0.13 to 20.02 mg L-1, respectively, with the highest concentration measured in July. ACfOPS and ACfCS removed up to 99.6 and 99.9% of AgNPs, respectively, from the water. The interaction mechanism between AgNPs and the activated carbon surface employed in this work was mainly the electrostatic force interaction via binding Ag+ with O- presented in the activated carbon to form AgO. Fifteen kinetic models were compared statistically to describe the removal of AgNPs. It was found that the experimental adsorption data can be best described using the mixed 1,2-order model. Therefore, this model has the potential to be a candidate for a general model to describe AgNPs adsorption using numerous materials, its validation of which has been confirmed with other material data from previous works.
This study presents the kinetics and thermodynamics of biomass pyrolysis. The kinetics of the pyrolysis process was estimated using ten kinetic models from three different mechanisms, namely chemical reaction, diffusion, and nucleation and growth. Results showed that each pyrolysis subdivision was described by a different reaction model, signifying the complex nature of the pyrolysis process. The average values of activation energy determined from the kinetic models for empty fruit bunch, coconut shell, bamboo, and cardboard are 10.2-64.6 kJ/mol, 18.7-186.2 kJ/mol, 8.0-70.8 kJ/mol, and 13.1-277.3 kJ/mol, respectively. The biomass pyrolysis is endothermic and non-spontaneous and would require external energy to initiate the degradation process. The findings are helpful in characterizing the thermal degradation of biomass in exploring its potential as a source of alternative solid fuel.
This work was aimed to evaluate the feasibility of castor bean residue based activated carbons prepared through metals chloride activation. The activated carbons were characterized for textural properties and surface chemistry, and the adsorption data of rhodamine B were established to investigate the removal performance. Zinc chloride-activated carbon with specific surface area of 395 m(2)/g displayed a higher adsorption capacity of 175 mg/g. Magnesium chloride and iron(III) chloride are less toxic and promising agents for composite chemical activation. The adsorption data obeyed Langmuir isotherm and pseudo-second-order kinetics model. The rate-limiting step in the adsorption of rhodamine B is film diffusion. The positive values of enthalpy and entropy indicate that the adsorption is endothermic and spontaneous at high temperature.
Kinetic model parameters for toluene conversion under microwave thermocatalytic treatment were evaluated. The kinetic rate constants were determined using integral method based on experimental data and coupled with Arrhenius equation for obtaining the activation energies and pre-exponential factors. The model provides a good agreement with the experimental data. The kinetic model was also validated with standard error of 3% on average. The extrapolation of the model showed a reasonable trend to predict toluene conversion and product yield both in thermal and catalytic treatments. Under microwave irradiation, activation energy of toluene conversion was lower in the range of 3-27 kJ mol(-1) compared to those of conventional heating reported in the literatures. The overall reaction rate was six times higher compared to conventional heating. As a whole, the kinetic model works better for tar model removal in the absence of gas reforming within a level of reliability demonstrated in this study.
In the study reported here, magnesium/aluminum (Mg/Al)-layered double hydroxide (LDH) was intercalated with an anticancer drug, protocatechuic acid, using ion-exchange and direct coprecipitation methods, with the resultant products labeled according to the method used to produce them: "PANE" (ie, protocatechuic acid-Mg/Al nanocomposite synthesized using the ion-exchange method) and "PAND" (ie, protocatechuic acid-Mg/Al nanocomposite synthesized using the direct method), respectively. Powder X-ray diffraction and Fourier transform infrared spectroscopy confirmed the intercalation of protocatechuic acid into the inter-galleries of Mg/Al-LDH. The protocatechuic acid between the interlayers of PANE and PAND was found to be a monolayer, with an angle from the z-axis of 8° for PANE and 15° for PAND. Thermogravimetric and differential thermogravimetric analysis results revealed that the thermal stability of protocatechuic acid was markedly enhanced upon intercalation. The loading of protocatechuic acid in PANE and PAND was estimated to be about 24.5% and 27.5% (w/w), respectively. The in vitro release study of protocatechuic acid from PANE and PAND in phosphate-buffered saline at pH 7.4, 5.3, and 4.8 revealed that the nanocomposites had a sustained release property. After 72 hours incubation of PANE and PAND with MCF-7 human breast cancer and HeLa human cervical cancer cell lines, it was found that the nanocomposites had suppressed the growth of these cancer cells, with a half maximal inhibitory concentration of 35.6 μg/mL for PANE and 36.0 μg/mL for PAND for MCF-7 cells, and 19.8 μg/mL for PANE and 30.3 μg/mL for PAND for HeLa cells. No half maximal inhibitory concentration for either nanocomposite was found for 3T3 cells.
The release of chlorophenoxyherbicides agrochemicals, namely 2-chloro- (2CPA), 4-chloro and 2,4,5-trichloro (TCPA) phenoxyacetates from their nanohybrids into various aqueous solutions; carbonate, sulfate and chloride was found to be controlled by pseudo-second order rate expression. The percentage saturated released was found to be anionic-dependent, in the order of carbonate>sulfate>chloride for the release media and 2CPA>4CPA>TCPA for the anionic guests. This study demonstrates that the release of the phenoxyherbicides agrochemicals from the nanohybrid compounds can be tuned by choosing the right combination of exchangeable anions both the incoming and the outgoing anions.
Wastewaters from textile industries may contain a variety of dyes that have to be removed before their discharge into waterways. Rice hull, an agricultural by-product, was modified using ethylenediamine to introduce active sites on its surface to enable it to function as a sorbent for both basic and reactive dyes. The sorption characteristics of Basic Blue 3 (BB3) and Reactive Orange 16 (RO16) by ethylenediamine modified rice hull (MRH) were studied under various experimental conditions. Sorption was pH and concentration dependent. Simultaneous removal of BB3 and RO16 occurred at pH greater than 4. The kinetics of dye sorption fitted a pseudo-second order rate expression. Increase in agitation rate had no effect on the sorption of BB3 but increased uptake of RO16 on MRH. Decreasing particle size increased the uptake of dyes in binary dye solutions. Equilibrium data could be fitted into both the Langmuir and Freundlich isotherms. Maximum sorption capacities calculated from the Langmuir model are 14.68 and 60.24 mg/g for BB3 and RO16, respectively in binary dye solutions. This corresponds to an enhancement of 4.5 and 2.4 fold, respectively, compared to single dye solutions. MRH therefore has the potential of being used as an efficient sorbent for the removal of both dyes in textile wastewaters.