Batu Reput’ is primary sediment mineral and abundantly found in Perlis. Perlis is one of the major producers of ‘Batu Reput’ in Malaysia that content large deposit of high-purity dolomite [CaMg (CO3)2]. Pure samples of ‘Batu Reput’ recently explored in the Koperasi Rimba Mas Padang Besar Quarry were investigated for their physical, chemical and mineralogical composition. SEM and XRD analysis methods were applied. The potential of ‘Batu Reput’ as a raw material in fertilizer production was investigated in this paper.
In this paper, an improved trigonometrically fitted zero-dissipative explicit two-step hybrid method with fifth algebraic
order is derived. The method is applied to several problems where by the solutions are oscillatory in nature. Numerical
results obtained are compared with existing methods in the scientific literature. The comparison shows that the new
method is more effective and efficient than the existing methods of the same order.
This paper is about the reduction of the overall size of metal blanking sheet that is being used to form a stamping product or car body panel of a car manufacturer in Malaysia. The current blanking sheet produces extra waste which will be recycled and does not contribute to increase productivity but increases inventory cost. The reduction in the blanking sheet size will lead to the reduction of raw material hence reduced the production cost. However, the reduced size of blanking sheet could affect the yield strength of the product. The study of the yield strength and yield improvement of the product are done by simulating stress analysis by using CATIA software. The results show that the new proposed size of the metal blanking sheet provides accuracy of the product dimension as well as maintaining the yield strength of the product and it reduced a significant amount of metal scrap which is nearly 4% of material weight and save around 10% of inventory cost.
One of the concerns in power system preventive control and security assessment is to find the point where the voltage and frequency collapse and when the system forces a severe disturbance. Identifying the weakest bus in a power system is an essential aspect of planning, optimising and post-event analysing procedures. This paper proposes an approach to identify the weakest bus from the frequency security viewpoint. The transient frequency deviation index for the individual buses is used as the weakest bus identification as well as a frequency security indicator. This approach will help to determine the bus with the worst deviation, which helps to analyse the system disturbance, takes proper control action to prevent frequency failure, and most importantly, observes consumer frequency. The approach is applied to the WSCC 9 bus test system to show the feasibility of the method.
In the organosolv pulping of the oil palm fronds, the influence of the operational variables of the pulping reactor (viz. cooking temperature and time, ethanol and NaOH concentration) on the properties of the resulting pulp (yield and kappa number) and paper sheets (tensile index and tear index) was investigated using a wavelet neural network model. The experimental results with error less than 0.0965 (in terms of MSE) were produced, and were then compared with those obtained from the response surface methodology. Performance assessment indicated that the neural network model possessed superior predictive ability than the polynomial model, since a very close agreement between the experimental and the predicted values was obtained.
A high recombination rate and low charge collection are the main limiting factors of copper oxides (cupric and cuprous oxide) for the photocatalytic degradation of organic pollutants. In this paper, a high performance copper oxide photocatalyst was developed by integrating cupric oxide (CuO) and cuprous oxide (Cu2O) thin films, which showed superior performance for the photocatalytic degradation of methylene blue (MB) compared to the control CuO and Cu2O photocatalyst. Our results show that a heterojunction photocatalyst of CuO-Cu2O thin films could significantly increase the charge collection, reduce the recombination rate, and improve the photocatalytic activity.
This paper utilizes the background oriented schlieren (BOS) technique to measure the velocity field of a variable density round jet. The density field of the jet is computed based on the light deflection created during the passage of light through the understudy jet. The deflection vector estimation was carried out using phase-based optical flow algorithms. The density field is further exploited to extract the axial and radial velocity vectors with the aid of continuity and energy equations. The experiment is conducted at six different jet-exit temperature values. Additional turbulence parameters, such as velocity variance and power spectral density of the vector field, are also computed. Finally, the measured velocity parameters are compared with the hot wire anemometer measurements and their correlation is displayed.
The default causal single-nucleotide polymorphism (SNP) effect size prior in Bayesian fine-mapping studies is usually the Normal distribution. This choice is often based on computational convenience, rather than evidence that it is the most suitable prior distribution. The choice of prior is important because previous studies have shown considerable sensitivity of causal SNP Bayes factors to the form of the prior. In some well-studied diseases there are now considerable numbers of genome-wide association study (GWAS) top hits along with estimates of the number of yet-to-be-discovered causal SNPs. We show how the effect sizes of the top hits and estimates of the number of yet-to-be-discovered causal SNPs can be used to choose between the Laplace and Normal priors, to estimate the prior parameters and to quantify the uncertainty in this estimation. The methodology can readily be applied to other priors. We show that the top hits available from breast cancer GWAS provide overwhelming support for the Laplace over the Normal prior, which has important consequences for variant prioritisation. This work in this paper enables practitioners to derive more objective priors than are currently being used and could lead to prioritisation of different variants.
The paper looks into the possibility of using standard addition method to analyse uranium and thorium in tin slag. Tin slag samples obtained from Butterworth was grind to 180 ȝm and injected with different concentrations of uranium and thorium. Linear calibration graphs were obtained for both these samples with R 2 values for uranium and thorium as 0.9989 and 0.9915 respectively. Based on this graphs, the initial uranium and thorium in the tin slag sample was established as 60 ppm for uranium and 160 ppm for thorium.
The unsteady mixed convection boundary layer flow near the forward stagnation point of a two-dimensional symmetric body prescribed by a uniform heat flux rate is studied in this paper. The main aim of the investigation is to identify situations in which dual solutions for the steady-state flow can be determined when the flow is opposing. It is also shown that there is a smooth transition from the unsteady initial flow (short time) to the final steady state flow (large time).
Heavy metals are highly toxic at trace levels and their pollution has shown great threat to the environment and public health worldwide where current detection methods require expensive instrumentation and laborious operation, which can only be accomplished in centralized laboratories. Herein, we report a low-cost, paper-based microfluidic analytical device (μPAD) for facile, portable, and disposable monitoring of mercury, lead, chromium, nickel, copper, and iron ions. Triple indicators or ligands that contain ions or molecules are preloaded on the μPADs and upon addition of a metal ion, the colorimetric indicators will elicit color changes observed by the naked eyes. The color features were quantitatively analyzed in a three-dimensional space of red, green, and blue or the RGB-space using digital imaging and color calibration techniques. The sensing platform offers higher accuracy for cross references, and is capable of simultaneous detection and discrimination of different metal ions in even real water samples. It demonstrates great potential for semiquantitative and even qualitative analysis with a sensitivity below the safe limit concentrations, and a controlled error range.
The flocculation performances of nine cationic and anionic polyacrylamides with different molecular weights and different charge densities in the treatment of pulp and paper mill wastewater have been studied. The experiments were carried out in jar tests with the polyacrylamide dosages range of 0.5-15 mg l(-1), rapid mixing at 200 rpm for 2 min, followed by slow mixing at 40 rpm for 15 min and settling time of 30 min. The effectiveness of the polyacrylamides was measured based on the reduction of turbidity, the removal of total suspended solids (TSS) and the reduction of chemical oxygen demand (COD). Cationic polyacrlyamide Organopol 5415 with very high molecular weight and low charge density is found to give the highest flocculation efficiency in the treatment of the paper mill wastewater. It can achieve 95% of turbidity reduction, 98% of TSS removal, 93% of COD reduction and sludge volume index (SVI) of 14 ml g(-1) at the optimum dosage of 5 mg l(-1). SVI values of less than 70 m lg(-1) are found for all polyacrylamide at their respective optimum dosage. Based on the cost evaluation, the use of the polyacrylamides is economically feasible to treat the pulp and paper mill wastewaters. This result suggests that single-polymer system can be used alone in the coagulation-flocculation process due to the efficiency of the polyacrylamide. Sedimentation of the sludge by gravity thickening with settling time of 30 min is possible based on the settling characteristics of the sludge produced by Organopol 5415 that can achieve 91% water recovery and 99% TSS removal after 30 min settling.
The development of Transparent Solar Cells (TSC) has become the main focus of solar energy research in recent years. The TSC has a number of applications and make use of unexploited space such as skyscraper windows. In this paper, TSC is fabricated using commercially available titanium dioxide (TiO2) P25 to make a paste, which is deposited on FTO glass using screen printing and spin coating methods. The effects of the thickness of the TiO2 film on transparency are examined. The paste is synthesised in the Cleanroom and used in both methods of deposition. The final cell fabrication is a Dye sensitised solar cell (DSSC). The obtained transparency of the FTO glass is 83%, and after the deposition of TiO2 it is reduced to less than 80%. The overall transparency of the DSSC, which was made using the spin coating method, is 70% with an Isc of 9.5 mA and Voc 853mV.
Preventive tests and diagnosis of in-service power transformer are important for early fault prediction and increased reliability of electricity supply. However, some existing diagnostic techniques require transformer outage before the measurement can be performed and need expert knowledge and experiences to interpret the measurement results. Other measurement techniques such as chemical analyses of insulating oil may cause significant variance to measurement results due to different practices in oil sampling, storage, handling and transportation of oil. A cost-effective measuring technique, which is simple, providing fast and an accurate measurement results, is therefore highly required. The extended application of Polarisation and Depolarisation (PDC) measurement for characterisation of different faults conditions in-service power transformer has been presented in this paper. Earlier studies on polarisation and depolarisation current of oil samples from in-service power transformer shows that depolarisation has provided significant information about the change of material properties due to faults in power transformer. In this paper, a new approach based on Depolarisation Current Ratio Index (DRI) was developed for identifying and classifying different transformer fault conditions. The DRI at time interval of 4s to 100s was analysed and the results show that DRI of depolarisation current between 5/100s and 10/100s provides higher correlation on the incipient faults in power transformer.
Pressurized water reactor (PWR) type AP1000 is a third generation of a nuclear
power plant. The primary system of PWR using uranium dioxide to generate heat energy
via fission process. The process influences temperature, pressure and pH value of water
chemistry of the PWR. The aim of this paper is to transform the primary system of PWR
using fuzzy autocatalytic set (FACS). In this work, the background of primary system
of PWR and the properties of the model are provided. The simulation result, namely
dynamic concentration of PWR is verified against published data.
n this paper, transformation and differentiation of Henstock-Wiener integrals are discussed. The approach is by Riemann sums. The idea is more transparent than that of classical Wiener integral.
Throughout the years, the construction industry has made an important contribution to the Malaysian economy. Moreover, the Ninth Malaysia Plan (2006–2010) has also played a significant role in the demands of executing major residential housing project developments where it has been observed that construction waste was one of the priority waste streams. Due to the increasing number in the population that is actively involved in economic activities, and the modernization of the country, the types of construction waste that are being produced, and identifying the source such as waste are becoming more complex. Therefore, appropriate actions and approaches are needed to be taken with respect to its effective management in handling the solid waste from construction sites. This paper is intended to review the issues and the challenges enclosed within the supply chain management mechanisms in order for improving construction waste management. Throughout this review, useful information and better understanding concerning the current issues, challenges and the supply chain management mechanisms would be made inclusive in the field to be explored. The findings would also assist in improving the quality and awareness on the construction waste management that is being practiced.
Technoeconomic paradigms based economic growth theories suggest that waves of technological innovations drove the economic growth of advanced economies. Widespread economic degradation and pollution is an unintended consequence of such growth. Tackling environmental and social issues at firm levels would help us to overcome such issues at macro-levels. Consequently, the Triple Bottom Line (TBL) reporting approach promotes firm level economic, environmental and social performances. Incorporating Zink's (2014) 3-pillar presentation model, this paper indicates that economic, social and environmental performances tend to be reported at firm level. All three pillars are not covered evenly at the activity levels. Thus, a loophole is identified whereby excellent environmental performance at activity levels could potentially leave poor social performance undisclosed. A refinement of the TBL paradigm, whereby all three pillars are covered at the activity level, is suggested, to enhance sustainability reporting.
The Lembah Bujang archeological complex near Sungai Petani, Kedah consists of various structures constructed at different times and spread over a wide area. This paper reports on the thermoluminescence (TL) dating of one of these structures. The structure was found to be 350 ± 90 yrs old. This is very young as compared with other structures that are from the 4th to the 16th centuries. This structure is suspected to be remnant of a Muslim Mosque whereas the other structures were Hindu and Buddist temples.
This paper studied the thermal behaviour of pineapple leaf fibre (PALF) reinforced high impact polystyrene (HIPS) composite. Thermogravimetric analysis (TGA) and differential scanning calorimetric (DSC) analysis were used to measure the thermal characteristic of HIPS/PALF composites. In particular, the TGA analysis was utilized to measure the degradation and decomposition of materials in neat polystyrene, pineapple fibre, and the composites. The measurements were carried out in the temperature of 25°C – 800°C, at a heating rate of 20°C min-1 and the nitrogen gas flow was 50 mL min-1. The temperature of the DSC analysis was programmed to be between 25°C – 300°C. The results from TGA analysis show that the addition of pineapple fibre has improved the thermal stability of the composites as compared to neat HIPS. In addition, the effects of compatibilising agent and surface modification of PALF with alkali treated were also determined and compared.