Displaying publications 1 - 20 of 120 in total

Abstract:
Sort:
  1. Mohamed M, Stednick JD, Smith FM
    Water Sci Technol, 2002;46(9):47-54.
    PMID: 12448451
    Some of the many tools used for watershed management are mathematical and computer models for wasteload allocations. QUAL2E is one of the most popular water quality models used for such purposes. The question arises as to whether the model is applicable in a different climate such as that in the tropics. In this study, QUAL2E was used to model Sg. Selangor River in Malaysia using the predictive equations for reaeration coefficient (k2) within the model and the measured reaeration coefficients for the river. The study results indicated that use of the reaeration coefficient (k2) measured at Sg. Selangor River did give the lowest standard error (SE) for the simulation of water quality during the 7Q10 low-flow period which is considered as the worst scene scenario in water quality modeling. But during calibration and validation using actual low-flow discharge data, the measured reaeration coefficients did not give the lowest standard error (SE). In conclusion, the results indicated that QUAL2E is applicable in tropical rivers when used with the modeled river parameters (i.e. hydraulic parameters, meteorological conditions etc.). Measured reaeration coefficients produced good results and several predictive equations also produced comparatively good results.
    Matched MeSH terms: Quality Control
  2. Lee KM, Lim PE
    Water Sci Technol, 2003;47(10):41-7.
    PMID: 12862215
    The objective of this study is to investigate the potential of the activated rice husk to be used as an alternative adsorbent to powdered activated carbon (PAC) in the simultaneous adsorption and biodegradation processes under sequencing batch reactor (SBR) operation to treat synthetic wastewater containing phenol, p-methylphenol, p-ethylphenol and p-isopropylphenol. The rice husk (PRH) was activated by pyrolysis at 600 degrees C for 5 hours in a nitrogen atmosphere. Using the Langmuir model, the limiting adsorption capacities of PRH for the phenols were found to vary from 0.015-0.05 of those of PAC. The SBR reactors with and without adsorbent addition were operated with fill, react, settle, draw and idle periods in the ratio of 4:6:1:0.76:0.25 for a cycle time of 12 hours. For phenolic wastewater containing, 1,200 mg/L phenol, 1,200 mg/L p-methylphenol, 800 mg/L p-ethylphenol and 660 mg/L p-isopropylphenol, it was found that the biodegradation process alone was unable to produce effluent of quality which would satisfy the discharge standards of COD < or = 100 mg/L and phenol concentration < or = 1 mg/L. The addition of PAC in the ratio of PAC/phenolic compound at 0.095 g/g for phenol, 0.119 g/g for p-methylpheol, 0.179 g/g for p-ethylphenol and 0.220 g/g for p-isopropylphenol, can improve the effluent quality to satisfy the discharge standards. Equivalent treatment performance was achieved with the use of PRH at dosages of 2-3 times higher than those of PAC for all the phenolic wastewater studied. The increased adsorption capacity of PRH shown in the treatment indicates bioregeneration of the adsorbed surface during the treatment process.
    Matched MeSH terms: Quality Control
  3. Morokuma K, Matsumura T, Yamamoto A, Sakai A, Hifumi T, Ato M, et al.
    Trop Biomed, 2021 Jun 01;38(2):111-118.
    PMID: 34172698 DOI: 10.47665/tb.38.2.042
    In 2000, an equine Yamakagashi (Rhabdophis tigrinus) antivenom (Lot 0001) was testmanufactured as an unapproved drug for treatment of Yamakagashi bites. It was stocked on the premise of super-legal use from the viewpoint of emergency health crisis management. The antivenom showed a strong neutralizing ability against the hemorrhagic and coagulation activity of the Yamakagashi venom in its potency test. One vial of the antivenom can effectively neutralize at least about 4 mg of Yamakagashi venom. Its efficacy has also been confirmed in patients with severe cases of R. tigrinus bite that has been used in emergency. In 2020, this antivenom (Lot 0001) has reached 20 years after its production. To evaluate the integrity and potency of the antivenom, quality control, safety and potency tests had been conducted almost every year since 2012. Physical and chemical tests (property test, moisture content test, insoluble foreign matter test, osmotic pressure ratio test, pH test, protein content test, endotoxin test, sterility test) of the antivenom, showed no significant changes throughout the years, when compared to the results immediately after its production in 2000. All the parameters measured were also within the standard values. In animal safety tests (test for absence of toxicity and pyrogen), there was no change in the test results during the storage period and no abnormalities were observed. The potency test (anti-coagulant activity) after 20 years of the product, showed the same potency as those recorded immediately after production. Therefore, in all of the stability monitoring tests conducted so far, the product did not show any significant change compared to the results immediately after production. This confirms the stability of the product during the stockpiling period to the present, that is, 20 years after production.
    Matched MeSH terms: Quality Control
  4. Naqvi AA, Hassali MA, Naqvi SBS, Aftab MT
    Trials, 2019 Aug 09;20(1):488.
    PMID: 31399128 DOI: 10.1186/s13063-019-3540-z
    BACKGROUND: The objective of this study is to evaluate the effectiveness of pharmacist intervention in improving disease knowledge, adherence to treatment, health-related quality of life (HRQoL) and direct cost of treatment. The study also documents patient satisfaction with pharmacist counselling as a quality control measure.

    METHODS/DESIGN: This is a randomized, single-blind, two-arm, controlled trial in patients with rheumatoid arthritis visiting outpatient rheumatology clinics in Karachi, Pakistan. We will enroll patients with established diagnosis of rheumatoid arthritis over 3 months. The patients would be randomized through a computer-generated list into the control group, i.e., usual care or into the intervention group, i.e., pharmaceutical care, in a ratio of 1:1, after providing signed written consent. The study will take place in two patient-visits over the course of 3 months. Patients in the intervention group would receive intervention from the pharmacist while those in the control group will receive usual care. Primary outcomes include change in mean score from baseline (week 0) and at follow up (week 12) in disease knowledge, adherence to medications and rehabilitation/physical therapy. The secondary outcomes include change in the mean direct cost of treatment, HRQoL and patient satisfaction with pharmacist counselling.

    DISCUSSION: This is a novel study that evaluates the role of the pharmacist in improving treatment outcomes in patients with rheumatoid arthritis. The results of this trial could set the foundation for future delivery of care for this patient population in Pakistan. The results of this trial would be published in a peer-reviewed journal.

    TRIAL REGISTRATION: ClinicalTrials.gov, NCT03827148 . Registered on February 2019.

    Matched MeSH terms: Quality Control
  5. Mazlyzam AL, Aminuddin BS, Lokman BS, Isa MR, Fuzina H, Fauziah O, et al.
    Med J Malaysia, 2004 May;59 Suppl B:39-40.
    PMID: 15468808
    Our objective is to determine the quality of tissue engineered human skin via immunostaining, RT-PCR and electron microscopy (SEM and TEM). Culture-expanded human keratinocytes and fibroblasts were used to construct bilayer tissue-engineered skin. The in vitro skin construct was cultured for 5 days and implanted on the dorsum of athymic mice for 30 days. Immunostaining of the in vivo skin construct appeared positive for monoclonal mouse anti-human cytokeratin, anti-human involucrin and anti-human collagen type I. RT-PCR analysis revealed loss of the expression for keratin type 1, 10 and 5 and re-expression of keratin type 14, the marker for basal keratinocytes cells in normal skin. SEM showed fibroblasts proliferating in the 5 days in vitro skin. TEM of the in vivo skin construct showed an active fibrocyte cell secreting dense collagen fibrils. We have successfully constructed bilayer tissue engineered human skin that has similar features to normal human skin.
    Matched MeSH terms: Quality Control
  6. Severyanova L, Lazarev A
    Med J Malaysia, 2005 Aug;60 Suppl D:71-4.
    PMID: 16315629
    The Russian Federation of higher medical institutions get State accreditation, if their activity conforms to criteria determined by the Ministry of Public Health and the Ministry of Education of the Russian Federation. Kursk State Medical University (KSMU) has a confirmed to requirement of accreditation by the Russian Federation, to conduct annually training of about 5000 students at 12 faculties. KSMU carries out pre-medical undergraduate and postgraduate training in the specialty "Doctor of medicine". For the first time in Russia KSMU was allowed to conduct a 6-year medical training with the use of English as an intermediary language by the Ministry of Public Health and the Ministry of Education. In this relation programmes of training teachers for conducting instruction with the use of an intermediary language (English) and training students Russian with the level necessary for free communication with Russian patients and staff of the clinics have been developed and realized.
    Matched MeSH terms: Quality Control
  7. Shahabudin SH
    Med J Malaysia, 2005 Aug;60 Suppl D:4-10.
    PMID: 16315616
    With globalization education has become a tradable service governed by the rules and regulations of GATS and worth trillions of dollars. International standards are rapidly being developed to facilitate cross border supply of services. In medical education, the WFME has produced International Guidelines on Quality in Medical Education which has a regional equivalent in the WHO Western Pacific Region, and the IIME has defined the minimum essential requirements of standards in medical education in seven core competences. Malaysia, having an explicit policy of making education a sector for revenue generation, has put in place regulatory frameworks and incentives to make the country a centre of educational excellence. Within the ambit of this national aspiration, medical education has grown phenomenally in the last decade. Standards and procedures for accreditation of medical schools in line with the world standards have been developed and implemented and policies are enforced to facilitate compliance to the standards. The ultimate goal is for medical schools to be self-accredited. In striving towards self-accreditation medical schools should be innovative in making changes in the three requirements of medical education. These are the intellectual and social imperatives and strategies for effective implementation.
    Matched MeSH terms: Quality Control
  8. Sekaran AS
    Med J Malaysia, 1974 Dec;29(2):97-102.
    PMID: 4282408
    Matched MeSH terms: Quality Control
  9. Abu Bakar S
    Malays J Pathol, 1997 Dec;19(2):93-7.
    PMID: 10879247
    Matched MeSH terms: Quality Control
  10. Pathmanathan R
    Malays J Pathol, 1988 Aug;10:7-13.
    PMID: 3252081
    Matched MeSH terms: Quality Control
  11. Zulkapli NA, Sobi S, Mohd Zubaidi NA, Abdullah JM
    Malays J Med Sci, 2016 Jul;23(4):1-4.
    PMID: 27660539 DOI: 10.21315/mjms2016.23.4.1
    The Malaysian Journal of Medical Sciences (MJMS) has conducted a simple analysis of its scholarly publication, based on the auto-generated data compiled from ScholarOne Manuscripts(™), an innovative, web-based, submission and peer-review workflow solution for scholarly publishers. The performance of the MJMS from 2014-2015 is reported on in this editorial, with a focus on the pattern of manuscript submission, geographical contributors and the acceptance-rejection rate. The total number of manuscript submissions has increased from 264 in 2014, to 272 in 2015. Malaysians are the main contributors to the MJMS. The total number of manuscript rejections following the review process was 79 (29.9%) in 2014, increasing to 92 (33.8%) the following year, in accordance with the exacting quality control criteria applied by the journal's editor to the submitted manuscripts.
    Matched MeSH terms: Quality Control
  12. Hamilton RG, Adkinson NF
    J Allergy Clin Immunol, 1998 Sep;102(3):482-90.
    PMID: 9768592
    BACKGROUND: No characterized diagnostic natural rubber latex skin testing material is licensed for use in the United States.

    OBJECTIVE: We have conducted a multicenter clinical skin testing study to document the safety and diagnostic sensitivity and specificity of a candidate Hevea brasiliensis nonammoniated latex (NAL) extract. These data are intended to support the licensing of this reagent for the diagnosis of latex allergy in high-risk populations.

    METHODS: Three hundred twenty-four subjects (304 adults and 20 children) were classified by their clinical history as having latex allergy (LA group, 124 adults and 10 children) or having no latex allergy (NLA group, 180 adults and 10 children). All subjects provided blood samples and then received sequential puncture skin tests (PSTs) at 1, 100, or 1000 microg/mL protein with a bifurcated needle and NAL (Greer Laboratories) from Malaysian Hevea brasiliensis (clone 600) sap. A 2-stage glove provocation test was used to clarify latex allergy status of individuals with positive history/negative PST result and negative history/positive PST result mismatches.

    RESULTS: Twenty-four subjects (15%) originally designated as having LA on the basis of their initial clinical history were reclassified to the NLA group on the basis of a negative glove provocation test result. Of the 134 subjects with LA, 54 (40%) were highly sensitive to latex, with a positive PST result at 1 microg/mL NAL. The Greer NAL reagent produced a positive PST rate (sensitivity) of 95% and 99% in subjects with LA at 100 microg/mL and 1 mg/mL, respectively. The negative PST rate (specificity) in 190 subjects with a negative history with the NAL extract at 100 microg/mL and 1 mg/mL, was 100% and 96%, respectively. Immediately after the PST, mild systemic reactions (mainly pruritus) were recorded in 16.1 % of the adults in the LA group and 4.4% of the adults in the NLA group. No reactions required treatment with epinephrine. Only mild delayed reactions were observed in 9.6% (LA group) and 2.8% (NLA group) of subjects 24 to 48 hours after PST. Mean wheal and erythema diameters measured in the 10 children in the LA group with spina bifida at 100 microg/mL and 1 mg/mL were similar to those observed in the adults in the LA group, suggesting that children are not at increased risk for systemic reactions compared with adults.

    CONCLUSIONS: A suggestive clinical history is necessary but not sufficient for a definitive diagnosis of IgE-dependent latex allergy. These data support the safety and diagnostic efficacy of the Greer NAL, skin test reagent at 100 micro/mL and 1 mg/mL for confirmatory PSTs.

    Matched MeSH terms: Quality Control
  13. Kuwawenaruwa A, Remme M, Mtei G, Makawia S, Maluka S, Kapologwe N, et al.
    PMID: 30461049 DOI: 10.1002/hpm.2702
    Health care financing reforms are gaining popularity in a number of African countries to increase financial resources and promote financial autonomy, particularly at peripheral health care facilities. The paper explores the establishment of facility bank accounts at public primary facilities in Tanzania, with the intention of informing other countries embarking on such reform of the lessons learned from its implementation process. A case study approach was used, in which three district councils were purposively sampled. A total of 34 focus group discussions and 14 in-depth interviews were conducted. Thematic content analysis was used during analysis. The study revealed that the main use of bank account revenue was for the purchase of drugs, medical supplies, and minor facility needs. To ensure accountability for funds, health care facilities had to submit monthly reports of expenditures incurred. District managers also undertook quality control of facility infrastructure, which had been renovated using facility resources and purchases of facility needs. Facility autonomy in the use of revenue retained in their accounts would improve the availability of drugs and service delivery. The experienced process of opening facility bank accounts, managing, and using the funds highlights the need to strengthen the capacity of staff and health-governing committees.
    Matched MeSH terms: Quality Control
  14. Lau S, Ng KH, Abdul Aziz YF
    Br J Radiol, 2016 Oct;89(1066):20160258.
    PMID: 27452264 DOI: 10.1259/bjr.20160258
    OBJECTIVE: To investigate the sensitivity and robustness of a volumetric breast density (VBD) measurement system to errors in the imaging physics parameters including compressed breast thickness (CBT), tube voltage (kVp), filter thickness, tube current-exposure time product (mAs), detector gain, detector offset and image noise.

    METHODS: 3317 raw digital mammograms were processed with Volpara(®) (Matakina Technology Ltd, Wellington, New Zealand) to obtain fibroglandular tissue volume (FGV), breast volume (BV) and VBD. Errors in parameters including CBT, kVp, filter thickness and mAs were simulated by varying them in the Digital Imaging and Communications in Medicine (DICOM) tags of the images up to ±10% of the original values. Errors in detector gain and offset were simulated by varying them in the Volpara configuration file up to ±10% from their default values. For image noise, Gaussian noise was generated and introduced into the original images.

    RESULTS: Errors in filter thickness, mAs, detector gain and offset had limited effects on FGV, BV and VBD. Significant effects in VBD were observed when CBT, kVp, detector offset and image noise were varied (p control is essential to keep the parameter errors within reasonable bounds. Volpara appears robust within those bounds, albeit for more advanced applications such as tracking density change over time, it remains to be seen how accurate the measures need to be.

    Matched MeSH terms: Quality Control
  15. Seet WT, Mat Afandi MA, Ishak MF, Hassan MNF, Ahmat N, Ng MH, et al.
    Stem Cell Res Ther, 2023 Oct 20;14(1):298.
    PMID: 37858277 DOI: 10.1186/s13287-023-03536-9
    Treatments for skin injuries have recently advanced tremendously. Such treatments include allogeneic and xenogeneic transplants and skin substitutes such as tissue-engineered skin, cultured cells, and stem cells. The aim of this paper is to discuss the general overview of the quality assurance and quality control implemented in the manufacturing of cell and tissue product, with emphasis on our experience in the manufacturing of MyDerm®, an autologous bilayered human skin substitute. Manufacturing MyDerm® requires multiple high-risk open manipulation steps, such as tissue processing, cell culture expansion, and skin construct formation. To ensure the safety and efficacy of this product, the good manufacturing practice (GMP) facility should establish a well-designed quality assurance and quality control (QA/QC) programme. Standard operating procedures (SOP) should be implemented to ensure that the manufacturing process is consistent and performed in a controlled manner. All starting materials, including tissue samples, culture media, reagents, and consumables must be verified and tested to confirm their safety, potency, and sterility. The final products should also undergo a QC testing series to guarantee product safety, efficacy, and overall quality. The aseptic techniques of cleanroom operators and the environmental conditions of the facility are also important, as they directly influence the manufacturing of good-quality products. Hence, personnel training and environmental monitoring are necessary to maintain GMP compliance. Furthermore, risk management implementation is another important aspect of QA/QC, as it is used to identify and determine the risk level and to perform risk assessments when necessary. Moreover, procedures for non-conformance reporting should be established to identify, investigate, and correct deviations that occur during manufacturing. This paper provides insight and an overview of the QA/QC aspect during MyDerm® manufacturing in a GMP-compliant facility in the Centre for Tissue Engineering and Regenerative Medicine, Faculty of Medicine, Universiti Kebangsaan Malaysia.
    Matched MeSH terms: Quality Control
  16. Teng KH, Kot P, Muradov M, Shaw A, Hashim K, Gkantou M, et al.
    Sensors (Basel), 2019 Jan 28;19(3).
    PMID: 30696110 DOI: 10.3390/s19030547
    : Concrete failure will lead to serious safety concerns in the performance of a building structure. It is one of the biggest challenges for engineers to inspect and maintain the quality of concrete throughout the service years in order to prevent structural deterioration. To date, a lot of research is ongoing to develop different instruments to inspect concrete quality. Detection of moisture ingress is important in the structural monitoring of concrete. This paper presents a novel sensing technique using a smart antenna for the non-destructive evaluation of moisture content and deterioration inspection in concrete blocks. Two different standard concrete samples (United Kingdom and Malaysia) were investigated in this research. An electromagnetic (EM) sensor was designed and embedded inside the concrete to detect the moisture content within the structure. In addition, CST microwave studio was used to validate the theoretical model of the EM sensor against the test data. The results demonstrated that the EM sensor at 2.45 GHz is capable of detecting the moisture content in the concrete with linear regression of R² = 0.9752. Furthermore, identification of different mix ratios of concrete were successfully demonstrated in this paper. In conclusion, the EM sensor is capable of detecting moisture content non-destructively and could be a potential technique for maintenance and quality control of the building performance.
    Matched MeSH terms: Quality Control
  17. Serag A, Zayed A, Mediani A, Farag MA
    Sci Rep, 2023 Feb 13;13(1):2533.
    PMID: 36781893 DOI: 10.1038/s41598-023-28551-x
    Tongkat ali commonly known as Malaysian Ginseng (Eurycoma longifolia) is a herbal root worldwide available in nutraceuticals, either as a crude powder or capsules blended with other herbal products. Herein, a multiplexed metabolomics approach based on nuclear magnetic resonance (NMR) and solid-phase microextraction combined with gas chromatography-mass spectrometry (SPME-GC-MS) was applied for authentic tongkat ali extract vs some commercial products quality control analysis. NMR metabolite fingerprinting identified 15 major metabolites mostly ascribed to sugars, organic and fatty acids in addition to quassinoids and cinnamates. Following that, multivariate analysis as the non-supervised principal component analysis (PCA) and supervised orthogonal partial least squares-discriminant analysis (OPLS-DA) were applied revealing that differences were related to fatty acids and 13,21-dihydroeurycomanone being more enriched in authentic root. SPME-GC-MS aroma profiling led to the identification of 59 volatiles belonging mainly to alcohols, aldehydes/furans and sesquiterpene hydrocarbons. Results revealed that aroma of commercial products showed relatively different profiles being rich in vanillin, maltol, and methyl octanoate. Whereas E-cinnamaldehyde, endo-borneol, terpinen-4-ol, and benzaldehyde were more associated to the authentic product. The present study shed the light for the potential of metabolomics in authentication and standardization of tongkat ali and identification of its true flavor composition.
    Matched MeSH terms: Quality Control
  18. Mod Ali N
    Radiat Prot Dosimetry, 2011 Mar;144(1-4):90-4.
    PMID: 21147789 DOI: 10.1093/rpd/ncq454
    As a laboratory certified to ISO 9001:2008 and accredited to ISO/IEC 17025, the Secondary Standard Dosimetry Laboratory (SSDL)-Nuclear Malaysia has incorporated an overall comprehensive system for technical and quality management in promoting a reliable individual monitoring service (IMS). Faster identification and resolution of issues regarding dosemeter preparation and issuing of reports, personnel enhancement, improved customer satisfaction and overall efficiency of laboratory activities are all results of the implementation of an effective quality system. Review of these measures and responses to observed trends provide continuous improvement of the system. By having these mechanisms, reliability of the IMS can be assured in the promotion of safe behaviour at all levels of the workforce utilising ionising radiation facilities. Upgradation of in the reporting program through a web-based e-SSDL marks a major improvement in Nuclear Malaysia's IMS reliability on the whole. The system is a vital step in providing a user friendly and effective occupational exposure evaluation program in the country. It provides a higher level of confidence in the results generated for occupational dose monitoring of the IMS, thus, enhances the status of the radiation protection framework of the country.
    Matched MeSH terms: Quality Control
  19. Noriah MA
    Radiat Prot Dosimetry, 2007;125(1-4):101-4.
    PMID: 17145724
    This paper discusses the advantage of certification process in the quality assurance of individual dose monitoring in Malaysia. The demand by customers and the regulatory authority for a higher degree of quality service requires a switch in emphasis from a technically focused quality assurance program to a comprehensive quality management for service provision. Achieving the ISO 9001:2000 certification by an accredited third party demonstrates acceptable recognition and documents the fact that the methods used are capable of generating results that satisfy the performance criteria of the certification program. It also offers a proof of the commitment to quality and, as a benchmark, allows measurement of the progress for continual improvement of service performance.
    Matched MeSH terms: Quality Control
  20. Samat SB, Evans CJ
    Radiat Prot Dosimetry, 2003;103(4):341-7.
    PMID: 12797557
    For the specific absorbed dose constant for 60Co photons, three values quoted directly in the literature and two derived indirectly from published information are reported. The three publications giving the direct values mentioned no medium of absorption, whereas the other two specify tissue. A database of the specific absorbed dose constant is generated for each of 14 media namely air, water, bone and 11 types of soft tissue. These values are consistent with the three directly quoted values plus one of the indirectly obtained values. Air is found to be unlikely as the medium for the first three; and appropriate media for these are suggested. For the other two values, the generated database suggests that one is too small to be accurate; while the other is correct for tissue (as stated in the publication). An apparent error of 10(3) is identified in one of the values directly quoted.
    Matched MeSH terms: Quality Control
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links