Displaying publications 1 - 20 of 176 in total

Abstract:
Sort:
  1. An assessment of selected trace elements in intertidal surface sediments collected from the Peninsular Malaysia
    Zulkifli SZ, Mohamat-Yusuff F, Arai T, Ismail A, Miyazaki N
    Environ Monit Assess, 2010 Oct;169(1-4):457-72.
    PMID: 19856123 DOI: 10.1007/s10661-009-1189-x
    Concentrations of 11 trace elements (V, Cr, Co, Ni, Cu, Zn, As, Ag, Cd, Pb, and U) were determined in the intertidal surface sediments of Peninsular Malaysia. The average trace element concentrations are ranked as follows: Zn>V>As>Cr>Pb>Cu>Ni>Co>U>g>Cd. Interim Sediment Quality Guidelines (ISQGs) employed in present study are the Australia and New Zealand joint guideline (ANZECC/ARMCANZ), and the Hong Kong authorities. From the pooled data, none of these trace elements have the average concentration above the ISQG-high values. However, As and Ag average concentrations were over the ISQG-low values. Some elements were found to have the average concentration above the ISQG-high and/or ISQG-low in certain locations, including Kampung Pasir Putih (JPP), Lumut Port (ALP), Kuala Perai (PKP), Port Dickson (NPD), and others. The lowest and highest concentrations in a specific sampling location and maritime area varied among the elements, variations that were greatly affected by natural and anthropogenic activities in a given area. For each trace element, there were various levels of concentration among the sampling locations and maritime areas. These patterns indicated pollutant sources of an element for each area perhaps derived from nearby areas and did not widely distributed to other locations. It is necessary for Malaysia to develop an ISQG for effective quick screening and evaluation of the coastal environment of Peninsular Malaysia.
    Matched MeSH terms: Water Pollution, Chemical/statistics & numerical data
  2. Factors driving changes in freshwater mussel (Bivalvia, Unionida) diversity and distribution in Peninsular Malaysia
    Zieritz A, Lopes-Lima M, Bogan AE, Sousa R, Walton S, Rahim KA, et al.
    Sci Total Environ, 2016 Nov 15;571:1069-78.
    PMID: 27473771 DOI: 10.1016/j.scitotenv.2016.07.098
    Freshwater mussels (Bivalvia, Unionida) fulfil important ecosystem functions and are one of the most threatened freshwater taxa globally. Knowledge of freshwater mussel diversity, distribution and ecology in Peninsular Malaysia is extremely poor, and the conservation status of half of the species presumed to occur in the region has yet to be assessed. We conducted the first comprehensive assessment of Peninsular Malaysia's freshwater mussels based on species presence/absence and environmental data collected from 155 sites spanning all major river catchments and diverse habitat types. Through an integrative morphological-molecular approach we recognised nine native and one widespread non-native species, i.e. Sinanodonta woodiana. Two species, i.e. Pilsbryoconcha compressa and Pseudodon cambodjensis, had not been previously recorded from Malaysia, which is likely a result of morphological misidentifications of historical records. Due to their restriction to single river catchments and declining distributions, Hyriopsis bialata, possibly endemic to Peninsular Malaysia, Ensidens ingallsianus, possibly already extinct in the peninsula, and Rectidens sumatrensis, particularly require conservation attention. Equally, the Pahang, the Perak and the north-western river catchments are of particular conservation value due to the presence of a globally unique freshwater mussel fauna. Statistical relationships of 15 water quality parameters and mussel presence/absence identified acidification and nutrient pollution (eutrophication) as the most important anthropogenic factors threatening freshwater mussel diversity in Peninsular Malaysia. These factors can be linked to atmospheric pollution, deforestation, oil-palm plantations and a lack of functioning waste water treatment, and could be mitigated by establishing riparian buffers and improving waste water treatment for rivers running through agricultural and residential land.
    Matched MeSH terms: Water Pollution, Chemical/analysis*
  3. Fulltext Advancements in Monitoring Water Quality Based on Various Sensing Methods: A Systematic Review
    Zainurin SN, Wan Ismail WZ, Mahamud SNI, Ismail I, Jamaludin J, Ariffin KNZ, et al.
    Int J Environ Res Public Health, 2022 Oct 28;19(21).
    PMID: 36360992 DOI: 10.3390/ijerph192114080
    Nowadays, water pollution has become a global issue affecting most countries in the world. Water quality should be monitored to alert authorities on water pollution, so that action can be taken quickly. The objective of the review is to study various conventional and modern methods of monitoring water quality to identify the strengths and weaknesses of the methods. The methods include the Internet of Things (IoT), virtual sensing, cyber-physical system (CPS), and optical techniques. In this review, water quality monitoring systems and process control in several countries, such as New Zealand, China, Serbia, Bangladesh, Malaysia, and India, are discussed. Conventional and modern methods are compared in terms of parameters, complexity, and reliability. Recent methods of water quality monitoring techniques are also reviewed to study any loopholes in modern methods. We found that CPS is suitable for monitoring water quality due to a good combination of physical and computational algorithms. Its embedded sensors, processors, and actuators can be designed to detect and interact with environments. We believe that conventional methods are costly and complex, whereas modern methods are also expensive but simpler with real-time detection. Traditional approaches are more time-consuming and expensive due to the high maintenance of laboratory facilities, involve chemical materials, and are inefficient for on-site monitoring applications. Apart from that, previous monitoring methods have issues in achieving a reliable measurement of water quality parameters in real time. There are still limitations in instruments for detecting pollutants and producing valuable information on water quality. Thus, the review is important in order to compare previous methods and to improve current water quality assessments in terms of reliability and cost-effectiveness.
    Matched MeSH terms: Water Pollution
  4. Removal of dyes using immobilized titanium dioxide illuminated by fluorescent lamps
    Zainal Z, Hui LK, Hussein MZ, Taufiq-Yap YH, Abdullah AH, Ramli I
    J Hazard Mater, 2005 Oct 17;125(1-3):113-20.
    PMID: 15996813
    The photodegradation of various dyes in aqueous solution was studied. Experiments were carried out using glass coated titanium dioxide thin film as photocatalyst. Photodegradation processes of methylene blue (MB), methyl orange (MO), indigo carmine (IC), chicago sky blue 6B (CSB), and mixed dye (MD, mixture of the four mentioned single dye) were reported. As each photodegradation system is pH dependent, the photodegradation experiment was carried out in each dye photodegradation reactive pH range at approximately 28 degrees C. The dyes removal efficiency was studied and compared using UV-vis spectrophotometer analysis. The total removal of each dye was: methylene blue (90.3%), methyl orange (98.5%), indigo carmine (92.4%), chicago sky blue 6B (60.3%), and mixed dyes (70.1%), respectively. The characteristic of the photocatalyst was investigated using X-ray diffractometer (XRD). The amount of each dye intermediate produced in the photodegradation process was also determined with the help of total organic carbon (TOC) analysis.
    Matched MeSH terms: Water Pollution, Chemical/prevention & control*
  5. Towards online surface water quality monitoring technology: A review
    Zaidi Farouk MIH, Jamil Z, Abdul Latip MF
    Environ Res, 2023 Dec 01;238(Pt 1):117147.
    PMID: 37716398 DOI: 10.1016/j.envres.2023.117147
    The exponential growth of human population and anthropogenic activities have led to the increase of global surface water contamination especially in river, lakes and ocean. Safe and clean surface water sources are crucial to human health and well-being, aquatic ecosystem, environment and economy. Thus, water monitoring is vital to ensure minimal and controllable contamination in the water sources. The conventional surface water monitoring method involves collecting samples on site and then testing them in the laboratory, which is time-consuming and not able to provide real-time water quality data. In addition, it involves many manpower and resources, costly and lack of integration. These make surface water quality monitoring more challenging. The incorporation of Internet of Things (IoT) and smart technology has contributed to the improvement of monitoring system. There are different approaches in the development and implementation of online surface water quality monitoring system to provide real-time data collection with lower operating cost. This paper reviews the sensors and system developed for the online surface water quality monitoring system in the previous studies. The calibration and validation of the sensors, and challenges in the design and development of online surface water quality monitoring system are also discussed.
    Matched MeSH terms: Water Pollution
  6. Water Quality Modelling for River Activities Management: Example from a Low- and Middle-Income Country
    Zahidi I, Wilson G, Brown K, Hou FKK
    J Health Pollut, 2020 Dec;10(28):201207.
    PMID: 33324504 DOI: 10.5696/2156-9614-10.28.201207
    Background: Rivers are susceptible to pollution and water pollution is a growing problem in low- and middle-income countries (LMIC) with rapid development and minimal environmental protections. There are universal pollutant threshold values, but they are not directly linked to river activities such as sand mining and aquaculture. Water quality modelling can support assessments of river pollution and provide information on this important environmental issue.

    Objectives: The objective of the present study was to demonstrate water quality modelling methodology in reviewing existing policies for Malaysian river catchments based on an example case study.

    Methods: The MIKE 11 software developed by the Danish Hydraulic Institute was used to model the main pollutant point sources within the study area - sand mining and aquaculture. Water quality data were obtained for six river stations from 2000 to 2015. All sand mining and aquaculture locations and approximate production capacities were quantified by ground survey. Modelling of the sand washing effluents was undertaken with the advection-dispersion module due to the nature of the fine sediment. Modelling of the fates of aquaculture deposits required both advection-dispersion and Danish Hydraulic Institute ECO Lab modules to simulate the detailed interactions between water quality determinants.

    Results: According to the Malaysian standard, biochemical oxygen command (BOD) and ammonium (NH4) parameters fell under Class IV at most of the river reaches, while the dissolved oxygen (DO) parameter varied between Classes II to IV. Total suspended solids (TSS) fell within Classes IV to V along the mid river reaches of the catchment.

    Discussion: Comparison between corresponding constituents and locations showed that the water quality model reproduced the long-term duration exceedance for the main body of the curves. However, the water quality model underestimated the infrequent high concentration observations. A standard effluent disposal was proposed for the development of legislation and regulations by authorities in the district that could be replicated for other similar catchments.

    Conclusions: Modelling pollutants enables observation of trends over the years and the percentage of time a certain class is exceeded for each individual pollutant. The catchment did not meet Class II requirements and may not be able to reach Class I without extensive improvements in the quality and reducing the quantity of both point and non-point effluent sources within the catchment.

    Competing Interests: The authors declare no competing financial interests.

    Matched MeSH terms: Water Pollution
  7. Determination of polychlorinated biphenyl congeners in water and sediment in North West Persian Gulf, Iran
    Zahed MA, Nabi Bidhendi G, Pardakhti A, Esmaili-Sari A, Mohajeri S
    Bull Environ Contam Toxicol, 2009 Dec;83(6):899-902.
    PMID: 19760353 DOI: 10.1007/s00128-009-9874-6
    Polychlorinated biphenyl (PCB) was detected as isomer groups (congener numbers 28, 52, 101, 118, 138, 153 and 180) in the coastal water and sediment of four stations around Shadegan wetland protected area in the northwestern part of the Persian Gulf. Total PCB concentration range was 8-375 ng/L in water and 3.4-50.2 μg/g in sediment. Concentration of different congeners and chromatogram indicates that the source of PCB in this area can be Clophen A60; it used for long time in Iranian electronic industries. Other chlorinated hydrocarbons such as lindane, DDT and their metabolites were also present in the samples.
    Matched MeSH terms: Water Pollution, Chemical/statistics & numerical data
  8. Fulltext Passive in situ remediation using permeable reactive barrier for groundwater treatment
    Zafira Madzin, Faradiella Mohd Kusin, Mohd Shakirin Md Zahar, Siti Nurjaliah Muhammad
    The Pertanika Journal of Scholarly Research Reviews, 2016;2(2):1-11.
    MyJurnal
    The contamination of water bodies from heavy metals, either from natural sources or
    anthropogenic sources, has become a major concern to the public. Industrial activities with improper
    water treatment, and then leach into the water body, have become contaminated and harmful to
    consume. Passive remediation is one of the treatments introduced to counter this problem as it is a low
    cost but effective technique. After being widely acknowledged and through research conducted, the
    most suitable remediation technique found is the permeable reactive barriers (PRBs). PRB is defined
    as an in situ permeable treatment zone filled with reactive materials, designed to intercept and
    remediate a contaminant plume under natural hydraulic gradients. There have been many findings
    made from PRB which can be used to remove contaminants such as heavy metal, chlorinated solvents,
    carbonates and aromatic hydrocarbons. The most crucial criteria in making a successful PRB is the
    reactive media used to remove contaminants. The current paper presents an overview of the PRB
    selective medias that have been used and also the unresolved issue on the long term performance of
    PRB. The overall methodology for the application of PRB at a given site is also discussed in this
    paper. This inexpensive but effective technique is crucial as a sustainable technology in order to treat
    the drainage before it enters water tables to prevent water pollution and can be used as an alternative
    raw water source.
    Matched MeSH terms: Water Pollution
  9. Water quality assessment of an unusual ritual well in Bangladesh and impact of mass bathing on this quality
    Zabed H, Suely A, Faruq G, Sahu JN
    Sci Total Environ, 2014 Feb 15;472:363-9.
    PMID: 24295752 DOI: 10.1016/j.scitotenv.2013.11.051
    A sacred ritual well with continuously discharging of methane gas through its water body was studied for physicochemical and microbiological quality in three seasons and during ritual mass bathing. Most of the physicochemical parameters showed significant seasonal variations (P<0.05) and a sharp fluctuation during mass bathing. Dissolved oxygen (DO) was found negatively correlated with temperature (r=-0.384, P<0.05), biochemical oxygen demand (BOD) (r=-0.58, P<0.001) and ammonia (r=-0.738, P<0.001), while BOD showed positive correlation with chemical oxygen demand (COD) (r=0.762, P<0.001) and ammonia (r=0.83, P<0.001). Simple regression analysis also yielded significant linear relationship in DO vs. temperature (r(2)=0.147, P<0.05), DO vs. ammonia (r(2)=0.544, P<0.001) and BOD vs. DO (r(2)=0.336, P<0.001). A total of eight microbial indicators were studied and found that all of them increased unusually during mass bathing comparing with their respective seasonal values. Total coliforms (TC) were found positively correlated with fecal coliforms (FC) (r=0.971), FC with Escherichia coli (EC) (r=0.952), EC with intestinal enterococci (IE) (r=0.921), fecal streptococci (FS) with IE (r=0.953) and Staphylococcus aureus (SA) with Pseudomonas aeruginosa (PA) (r=0.946), which were significant at P<0.001. Some regression models showed significant linear relationship at P<0.001 with r(2) value of 0.943 for FC vs. TC, 0.907 for EC vs. FC, 0.869 for FS vs. FC, 0.848 for IE vs. EC and 0.909 for IE vs. FS. The overall results found in this study revealed that well water is suitable for bathing purpose but the religious activity considerably worsen its quality.
    Matched MeSH terms: Water Pollution/analysis*; Water Pollution/statistics & numerical data
  10. Fulltext Optimization of process condition for extraction of gelatin from red tilapia skin (Oreochromis niloticus) by High Pressure Processing (HPP)
    Yusof, N., Jaswir, I., Jamal, P., Jami, M.S., Octavianti, F.
    International Food Research Journal, 2017;24(101):0-0.
    MyJurnal
    Extraction of gelatin using traditional acid-base pretreatment method has several limitations
    such as time consuming and causes serious water pollution. Chemical treatment often being used
    as an alternative process to overcome the weaknesses of the conventional method. However,
    excessive chemical elements would damage the structure of the gelatin due to its high sensitivity
    to the acid content. High Pressure Processing (HPP) is a novel and environmental friendly
    method that has been suggested to assist gelatin extraction. Pressurization during pretreatment
    could reduce the extraction time and amount of acid used. It also has a potential in enhancing the
    properties of the gelatin extract and increasing the gelatin yield. In this research, One-Factor-
    at-Time (OFAT) and optimization study were done to determine the optimum parameters for
    extraction of gelatin assisted by HPP from red tilapia skin. Four parameters; applied pressure,
    pressure holding time, ratio of acid to skin and extraction time have been selected for the OFAT
    design and concentration of the gelatin extract and percentage of yield gelatin were evaluated.
    From OFAT, optimum technical parameters for response surface optimization design were 250
    MPa pressure, 7.5 ml of acid to 1 g of skin and 12 hours extraction time. Pressure holding
    time was fixed for 10 min. FCCCD has been used for optimization study. Results from the
    data shows that the optimum conditions for gelatin extraction from red tilapia skin were 250
    MPa for pressure, 10 min of pressure holding time, 7.5 ml of acid for 1 g of skin and 12 hours
    of extraction time while the maximum concentration and yield were 19.51 mg/ml and 32.04%
    (320.4 mg/g), respectively. These findings proved that HPP could increase the concentration
    and the yield of the gelatin while reducing the chemical waste and shortening the extraction
    process.
    Matched MeSH terms: Water Pollution
  11. Fulltext Trend analysis of water quality at Sungai Sarawak
    Yuhani Jamian, Zainap Lamat, Nurazura Rali
    Pertanika Journal of Science & Technology, 2017;25(105):55-62.
    MyJurnal
    Sungai Sarawak is the most important river in Sarawak. This study was aimed at assessing water quality in the selected stations from Satok bridge to the downstream, Muara Tebas, located along Sungai Sarawak. Water quality trend analysis was conducted to determine the correlation between the water quality parameters. Trend analysis was carried out using Mann-Kendall Test because data collected was non-parametric. Next, Spearman rank was used in order to determine the correlation between parameters. The results obtained and the observation made in this study reveals that the trend exists only for Chemical Oxygen Value (COD). But there are trends for Biochemical Oxygen Demand, (BOD), Dissolved Oxygen (DO), Total Suspended Solid (TSS), Ammoniacal Nitrogen (NH4N) and Turbidity to decrease or increase with no trends between 2007 and 2011. The correlation between parameters is not very strong because there are many determinants of water quality parameters. The result from this study would provide useful information for water quality management in order to maintain and improve the water quality of Sungai Sarawak.
    Matched MeSH terms: Water Pollution, Chemical
  12. Use of cestodes as indicator of heavy-metal pollution
    Yen Nhi TT, Mohd Shazili NA, Shaharom-Harrison F
    Exp Parasitol, 2013 Jan;133(1):75-9.
    PMID: 23146722 DOI: 10.1016/j.exppara.2012.10.014
    Thirty snakehead fish, Channa micropeltes (Cuvier, 1831) were collected at Lake Kenyir, Malaysia. Muscle, liver, intestine and kidney tissues were removed from each fish and the intestine was opened to reveal cestodes. In order to assess the concentration of heavy metal in the environment, samples of water in the surface layer and sediment were also collected. Tissues were digested and the concentrations of manganese (Mn), zinc (Zn), copper (Cu), cadmium (Cd) and lead (Pb) were analysed by using inductively-coupled plasma mass-spectrometry (ICP-MS) equipment. The results demonstrated that the cestode Senga parva (Fernando and Furtado, 1964) from fish hosts accumulated some heavy metals to a greater extent than the water and some fish tissues, but less than the sediment. In three (Pb, Zn and Mn) of the five elements measured, cestodes accumulated the highest metal concentrations, and in remaining two (Cu and Cd), the second highest metal accumulation was recorded in the cestodes when compared to host tissues. Therefore, the present study indicated that Senga parva accumulated metals and might have potential as a bioindicator of heavy-metal pollution.
    Matched MeSH terms: Water Pollution/analysis*
  13. Concentrations of heavy metals (Cu, Cd, Zn and Ni) and PAHs in Perna viridis collected from seaport and non-seaport waters in the Straits of Johore
    Yap CK, Shahbazi A, Zakaria MP
    Bull Environ Contam Toxicol, 2012 Dec;89(6):1205-10.
    PMID: 23052577 DOI: 10.1007/s00128-012-0838-x
    In this study, the ranges of pollutants found in the soft tissues of Perna viridis collected from Kg. Masai and Kg. Sg. Melayu, both located in the Straits of Johore, were 0.85-1.58 μg/g dry weight (dw) for Cd, 5.52-12.2 μg/g dw for Cu, 5.66-8.93 μg/g dw for Ni and 63.4-72.3 μg/g dw for Zn, and 36.4-244 ng/g dry weight for ∑PAHs. Significantly (p < 0.05) higher concentrations of Cd, Cu, Ni, Zn and ∑PAHs in the mussels were found in the water of a seaport site at Kg. Masai than a non-seaport site at Kg. Sg. Melayu population. The ratios of low molecular weight/high molecular weight hydrocarbons (2.94-3.42) and fluoranthene/pyrene (0.43-0.45) in mussels from both sites indicated the origin of the PAHs to be mainly petrogenic. This study has demonstrated the utility of using the soft tissues of P. viridis as a biomonitor of PAH contamination and bioavailability in the coastal waters of Peninsular Malaysia.
    Matched MeSH terms: Water Pollution, Chemical/statistics & numerical data
  14. Allozyme polymorphisms in horseshoe crabs, Carcinoscorpius rotundicauda, collected from polluted and unpolluted intertidal areas in Peninsular Malaysia
    Yap CK, Chong CM, Tan SG
    Environ Monit Assess, 2011 Mar;174(1-4):389-400.
    PMID: 20437264 DOI: 10.1007/s10661-010-1464-x
    It has been widely reported that allozyme frequency variation is a potential indicator of heavy metal-induced impacts in aquatic populations. In the present study, wild populations of horseshoe crab (Carcinoscorpius rotundicauda) were collected from contaminated and uncontaminated sites of Peninsular Malaysia. By adopting horizontal starch gel electrophoresis, seven enzyme systems were used to study allozyme polymorphisms. Nine polymorphic loci were observed in C. rotundicauda. The relationships of allozyme variations with the concentrations of Cd, Cu, Ni, and Zn in sediments and in muscle tissues of horseshoe crabs were determined. Based on genetic distance, the lower mean value of Nei's D (0.017) indicated that both of the contaminated populations of Kg. Pasir Puteh and Kuala Juru were very closely related when compared to the relatively uncontaminated Pantai Lido population. Higher heterozygosities were shown by the contaminated populations when compared to the uncontaminated population. Different allelic frequencies could be observed for the aldolase (ALD; E.C. 2.7.5.1) locus between the contaminated and uncontaminated populations of C. rotundicauda. The dendrogram of genetic relationships of the three populations of C. rotundicauda showed the same clustering pattern as the dendrograms are based on heavy metals in the sediments and in the horseshoe crabs' abdominal muscles. From the F statistics, the present study showed that the three populations of horseshoe crabs were considered to have undergone moderate genetic differentiation with a mean F (ST) value of 0.092 .The current results suggest that allozyme polymorphism in horseshoe crabs is a potential biomonitoring tool for metal contamination, although further validation is required.
    Matched MeSH terms: Water Pollution*
  15. Pollution problems in the Prefacture of Osaka
    Yamaguchi M
    Med J Malaysia, 1974 Dec;29(2):114-24.
    PMID: 4282396
    Matched MeSH terms: Water Pollution/prevention & control
  16. Fluoride contamination, health problems and remediation methods in Asian groundwater: A comprehensive review
    Yadav KK, Kumar S, Pham QB, Gupta N, Rezania S, Kamyab H, et al.
    Ecotoxicol Environ Saf, 2019 Oct 30;182:109362.
    PMID: 31254856 DOI: 10.1016/j.ecoenv.2019.06.045
    In low concentration, fluoride is considered a necessary compound for human health. Exposure to high concentrations of fluoride is the reason for a serious disease called fluorosis. Fluorosis is categorized as Skeletal and Dental fluorosis. Several Asian countries, such as India, face contamination of water resources with fluoride. In this study, a comprehensive overview on fluoride contamination in Asian water resources has been presented. Since water contamination with fluoride in India is higher than other Asian countries, a separate section was dedicated to review published articles on fluoride contamination in this country. The status of health effects in Asian countries was another topic that was reviewed in this study. The effects of fluoride on human organs/systems such as urinary, renal, endocrine, gastrointestinal, cardiovascular, brain, and reproductive systems were another topic that was reviewed in this study. Different methods to remove fluoride from water such as reverse osmosis, electrocoagulation, nanofiltration, adsorption, ion-exchange and precipitation/coagulation were introduced in this study. Although several studies have been carried out on contamination of water resources with fluoride, the situation of water contamination with fluoride and newly developed technology to remove fluoride from water in Asian countries has not been reviewed. Therefore, this review is focused on these issues: 1) The status of fluoride contamination in Asian countries, 2) health effects of fluoride contamination in drinking water in Asia, and 3) the existing current technologies for defluoridation in Asia.
    Matched MeSH terms: Water Pollution
  17. The impact of Japanese nuclear wastewater discharge into the sea on the global economy: Input-output model approach
    Wu X, Zhang Y, Feng X
    Mar Pollut Bull, 2023 Jul;192:115067.
    PMID: 37269704 DOI: 10.1016/j.marpolbul.2023.115067
    As the division of work within the world economic system becomes increasingly complex, the impact of disturbing events on the economic system is expanding. Recently, Japan proposed to discharge nuclear wastewater into the Pacific Ocean, which will cause damage to marine fisheries, thereby seriously affecting fisheries and other industries in Japan and other countries and regions around the world. Considering different scenarios of final and intermediate demand shifting, this paper uses the Inoperability Input-Output Model (IIM) and Multi-Region Input-Output Model (MRIO) to simulate the economic consequences of nuclear wastewater discharge in Japan and calculate the economic changes of each industry and country (region). The results show that: In the short term, when only the final demand for Japanese fishery products decreases. (1) The ten countries (regions) with significant economic losses are Japan, the United States, Chinese Taipei, Canada, Chile, South Africa, Mexico, Peru, the United Kingdom, and Ireland. (2) The ten countries (regions) with a significant increase in total output due to demand shift are China (People's Republic of), the Rest of the World, India, Indonesia, Viet Nam, the Philippines, Brazil, Myanmar, the Russian Federation, and Malaysia. (3) A ranking of changes in the total output of different industries. In the long term, when both intermediate and final demand for Japanese fishery products decrease. (4) The change in value added in Japan. (5) The change in value added of 67 countries (regions) worldwide. The ten countries (regions) with the most significant increase in value-added are the Russian Federation, China (People's Republic of), the Rest of the World, the United States, Indonesia, Australia, Norway, Korea, Viet Nam, and Myanmar. The ten countries (regions) with the most significant decrease in value-added are Japan, Chinese Taipei, Chile, South Africa, Peru, Thailand, Mexico, Cambodia, Costa Rica, and Morocco. Changes in value added of 45 industrial sectors worldwide.
    Matched MeSH terms: Water Pollution*
  18. Pollution control technologies for the treatment of palm oil mill effluent (POME) through end-of-pipe processes
    Wu TY, Mohammad AW, Jahim JM, Anuar N
    J Environ Manage, 2010 Jul;91(7):1467-90.
    PMID: 20231054 DOI: 10.1016/j.jenvman.2010.02.008
    Palm oil production is one of the major industries in Malaysia and this country ranks one of the largest productions in the world. In Malaysia, the total production of crude palm oil in 2008 was 17,734,441 tonnes. However, the production of this amount of crude palm oil results in even larger amounts of palm oil mill effluent (POME). In the year 2008 alone, at least 44 million tonnes of POME was generated in Malaysia. Currently, the ponding system is the most common treatment method for POME but other processes such as aerobic and anaerobic digestion, physicochemical treatment and membrane filtration may also provide the palm oil industries with possible insights into the improvement of POME treatment processes. Generally, open ponding offers low capital and operating costs but this conventional method is becoming less attractive because the methane produced is wasted to the atmosphere and the system can not be certified for Carbon Emission Reduction trading. On the other hand, anaerobic digestion of POME provides the fastest payback of investment because the treatment enables biogas recovery for heat generation and treated effluent for land application. Lastly, it is proposed herewith that wastewater management based on the promotion of cleaner production and environmentally sound biotechnologies should be prioritized and included as a part of the POME management in Malaysia for attaining sustainable development. This paper thus discusses and compares state-of-the-art POME treatment methods as well as their individual performances.
    Matched MeSH terms: Water Pollution, Chemical/prevention & control*
  19. Fulltext Pharmaceutical pollution of the world's rivers
    Wilkinson JL, Boxall ABA, Kolpin DW, Leung KMY, Lai RWS, Galbán-Malagón C, et al.
    Proc Natl Acad Sci U S A, 2022 Feb 22;119(8).
    PMID: 35165193 DOI: 10.1073/pnas.2113947119
    Environmental exposure to active pharmaceutical ingredients (APIs) can have negative effects on the health of ecosystems and humans. While numerous studies have monitored APIs in rivers, these employ different analytical methods, measure different APIs, and have ignored many of the countries of the world. This makes it difficult to quantify the scale of the problem from a global perspective. Furthermore, comparison of the existing data, generated for different studies/regions/continents, is challenging due to the vast differences between the analytical methodologies employed. Here, we present a global-scale study of API pollution in 258 of the world's rivers, representing the environmental influence of 471.4 million people across 137 geographic regions. Samples were obtained from 1,052 locations in 104 countries (representing all continents and 36 countries not previously studied for API contamination) and analyzed for 61 APIs. Highest cumulative API concentrations were observed in sub-Saharan Africa, south Asia, and South America. The most contaminated sites were in low- to middle-income countries and were associated with areas with poor wastewater and waste management infrastructure and pharmaceutical manufacturing. The most frequently detected APIs were carbamazepine, metformin, and caffeine (a compound also arising from lifestyle use), which were detected at over half of the sites monitored. Concentrations of at least one API at 25.7% of the sampling sites were greater than concentrations considered safe for aquatic organisms, or which are of concern in terms of selection for antimicrobial resistance. Therefore, pharmaceutical pollution poses a global threat to environmental and human health, as well as to delivery of the United Nations Sustainable Development Goals.
    Matched MeSH terms: Water Pollution, Chemical/analysis*; Water Pollution, Chemical/prevention & control*
  20. Tap water contamination: Multiclass endocrine disrupting compounds in different housing types in an urban settlement
    Wee SY, Aris AZ, Yusoff FM, Praveena SM
    Chemosphere, 2021 Feb;264(Pt 1):128488.
    PMID: 33045559 DOI: 10.1016/j.chemosphere.2020.128488
    Contamination of endocrine disrupting compounds (EDCs) in tap water is an emerging global issue, and there are abundant influencing factors that have an ambivalent effect on their transportation and fate. Different housing types vary in terms of water distribution system operation and design, water consumption choices, and other hydraulic factors, which potentially affect the dynamics, loadings, and partitioning of pollutants in tap water. Thus, this study analyzed 18 multiclass EDCs in tap water from different housing types (i.e., landed and high-rise) and the associated health risks. Sample analyses revealed the presence of 16 EDCs, namely hormones (5), pharmaceuticals (8), a pesticide (1), and plasticizers (2) in tap water, with the prevalent occurrence of bisphenol A up to 66.40 ng/L in high-rise housing. The presence of caffeine and sulfamethoxazole distribution in tap water was significantly different between landed and high-rise housings (t(152) = -2.298, p = 0.023 and t(109) = 2.135, p = 0.035). Moreover, the salinity and conductivity of tap water in high-rise housings were significantly higher compared to those in landed housings (t(122) = 2.411, p = 0.017 and t(94) = 2.997, p = 0.003, respectively). Furthermore, there were no potential health risks of EDCs (risk quotient water intake. However, EDC variation in different housing types requires simulation of the occurrence, transport, and fate of EDCs in the distribution system and investigation of the underlying factors for effective mitigation, prevention, and intervention.
    Matched MeSH terms: Water Pollution
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links