Displaying publications 1 - 20 of 112 in total

Abstract:
Sort:
  1. Ayub KR, Zakaria NA, Abdullah R, Ramli R
    Water Sci Technol, 2010;62(8):1931-6.
    PMID: 20962410 DOI: 10.2166/wst.2010.473
    The Bio-ecological Drainage System, or BIOECODS, is an urban drainage system located at the Engineering Campus, Universiti Sains Malaysia. It consists of a constructed wetland as a part of the urban drainage system to carry storm water in a closed system. In this closed system, the constructed wetland was designed particularly for further treatment of storm water. For the purpose of studying the water balance of the constructed wetland, data collection was carried out for two years (2007 and 2009). The results show that the constructed wetland has a consistent volume of water storage compared to the outflow for both years with correlation coefficients (R(2)) of 0.99 in 2007 and 0.86 in 2009.
    Matched MeSH terms: Hydrodynamics
  2. Lim ZF, Rajendran P, Musa MY, Lee CF
    Vis Comput Ind Biomed Art, 2021 May 20;4(1):14.
    PMID: 34014417 DOI: 10.1186/s42492-021-00080-2
    A numerical simulation of a patient's nasal airflow was developed via computational fluid dynamics. Accordingly, computerized tomography scans of a patient with septal deviation and allergic rhinitis were obtained. The three-dimensional (3D) nasal model was designed using InVesalius 3.0, which was then imported to (computer aided 3D interactive application) CATIA V5 for modification, and finally to analysis system (ANSYS) flow oriented logistics upgrade for enterprise networks (FLUENT) to obtain the numerical solution. The velocity contours of the cross-sectional area were analyzed on four main surfaces: the vestibule, nasal valve, middle turbinate, and nasopharynx. The pressure and velocity characteristics were assessed at both laminar and turbulent mass flow rates for both the standardized and the patient's model nasal cavity. The developed model of the patient is approximately half the size of the standardized model; hence, its velocity was approximately two times more than that of the standardized model.
    Matched MeSH terms: Hydrodynamics
  3. Panda D, Manickam S
    Ultrason Sonochem, 2019 Mar;51:526-532.
    PMID: 30224289 DOI: 10.1016/j.ultsonch.2018.04.003
    Dicofol, a recommended Stockholm convention persistent organic pollutants (POPs) candidate is well known for its endocrine disruptive properties and has been extensively used as an organochlorine pesticide worldwide. The hydrodynamic cavitation (HC) treatment of Dicofol in aqueous media induced by a liquid whistle hydrodynamic cavitaion reactor (LWHCR) has been investigated while considering important parameters such as inlet pressure, initial concentration of Dicofol, solution temperature, pH, addition of H2O2 and radical scavenger for the extent of degradation. The pseudo-first-order degradation rate constant (k) was determined to be 0.073 min-1 with a cavitational yield of 1.26 × 10-5 mg/J at optimum operating conditions and a complete removal of Dicofol was achieved within 1 h of treatment. Considering the removal rate and energy efficiency, the optimal inlet pressure was found to be 7 bar, resulting in a cavitation number of 0.17. High performance liquid chromatography (HPLC) and Gas chromatography mass spectroscopy (GC-MS) analyses indicated a sharp decline in the concentration of Dicofol with treatment time and indicated the presence of degraded products. An 85% total organic carbon (TOC) removal was achieved within 1 h of treatment time, demonstrating successful mineralization of Dicofol. The obtained results suggest that the degradation of Dicofol followed thermal decomposition and successive recombination reactions at bubble-vapor interface. Overall, the attempted hydrodynamic cavitation demonstrated successful and rapid removal of endocrine disruptive chemicals such as Dicofol and is expected to provide efficient solution for wastewater treatment.
    Matched MeSH terms: Hydrodynamics*
  4. ALIATULNAJIHA AYUB, MOHD ASAMUDIN A RAHMAN
    MyJurnal
    A numerical study is conducted to determine the Vortex Induced Motion (VIM) effects on Deep-Draft Semi-Submersibles (DDSS). The VIM phenomena is a crucial problem that can cause severe impact on the fatigue life of mooring risers in DDSS. Therefore, a comprehensive numerical simulation is conducted using the Acusolve computational fluid dynamics (CFD) software. Five models of immersed columns with different aspect ratios (ie. 0.6, 0.8, 1.0, 1.2 and 1.4) are numerically investigated under two different incidence angles, which are 0° and 45°. The transverse and in-line vibration amplitude, amplitude of lift force coefficient and vortex shedding are analyzed. The numerical measurements are obtained to see the response of horizontal plane motions, which are transverse, in line and yaw motions. This study with detailed numerical results from parametric data will contribute future studies and the comparisons are made to demonstrate the capability of the present CFD approach.
    Matched MeSH terms: Hydrodynamics
  5. LIM XUE YEN, AHMAD FITRIADHY
    MyJurnal
    Concerning on navigational safety of a ship, comprehensive investigation of manoeuvrability of the ship is prominently required. The turning instability due to improper speed and magnitude of the rudder angle is vulnerable to serious accidents such as collision especially in the confined waters. This paper presents a computational fluid dynamic analyses on manoeuvrability performance of a tug in calm water. Here, the characteristics of the turning ability and zig-zag characteristics of the tug has been assessed due to effect of the various angles of twin-rudder and turning speeds. The results revealed that the increase of rudder’s angle resulted in subsequent reduction of her advance diameter from 144 m, 108 m, 96 m to 92 m. While for zig zag manoeuvre, the first overshoot angle is 0.6° and 1.08° for 10°/10° and 20°/20° rudder’s angle respectively. The first overshoot and second overshoot angle are within the IMO criteria which is below 20° and 25°. However, the increase of turning speed from 7 knots to 9 knots has been proportional with the increase of the turning diameter (advance diameter) from 70 m to 105.2 m. Basically, the turning performances of the tug manoeuvring with the turning speed of 7 to 9 knots incorporated with rudder’s angle 20°, 25°, 30° and 35° have been complied with IMO manoeuvring standards. This preliminary analysis contributes very valuable findings at early ship design stage to provide a safety of the navigational guidance for turning ability of the tug.
    Matched MeSH terms: Hydrodynamics
  6. Tisa F, Raman AA, Daud WM
    ScientificWorldJournal, 2014;2014:348974.
    PMID: 25309949 DOI: 10.1155/2014/348974
    Simulation of fluidized bed reactor (FBR) was accomplished for treating wastewater using Fenton reaction, which is an advanced oxidation process (AOP). The simulation was performed to determine characteristics of FBR performance, concentration profile of the contaminants, and various prominent hydrodynamic properties (e.g., Reynolds number, velocity, and pressure) in the reactor. Simulation was implemented for 2.8 L working volume using hydrodynamic correlations, continuous equation, and simplified kinetic information for phenols degradation as a model. The simulation shows that, by using Fe(3+) and Fe(2+) mixtures as catalyst, TOC degradation up to 45% was achieved for contaminant range of 40-90 mg/L within 60 min. The concentration profiles and hydrodynamic characteristics were also generated. A subsequent scale-up study was also conducted using similitude method. The analysis shows that up to 10 L working volume, the models developed are applicable. The study proves that, using appropriate modeling and simulation, data can be predicted for designing and operating FBR for wastewater treatment.
    Matched MeSH terms: Hydrodynamics
  7. Low WS, Kadri NA, Abas WA
    ScientificWorldJournal, 2014;2014:961301.
    PMID: 25136701 DOI: 10.1155/2014/961301
    We propose a strategy for optimizing distribution of flow in a typical benchtop microfluidic chamber for dielectrophoretic application. It is aimed at encouraging uniform flow velocity along the whole analysis chamber in order to ensure DEP force is evenly applied to biological particle. Via the study, we have come up with a constructive strategy in improving the design of microfluidic channel which will greatly facilitate the use of DEP system in laboratory and primarily focus on the relationship between architecture and cell distribution, by resorting to the tubular structure of blood vessels. The design was validated by hydrodynamic flow simulation using COMSOL Multiphysics v4.2a software. Simulations show that the presence of 2-level bifurcation has developed portioning of volumetric flow which produced uniform flow across the channel. However, further bifurcation will reduce the volumetric flow rate, thus causing undesirable deposition of cell suspension around the chamber. Finally, an improvement of microfluidic design with rounded corner is proposed to encourage a uniform cell adhesion within the channel.
    Matched MeSH terms: Hydrodynamics
  8. Yarmand H, Gharehkhani S, Kazi SN, Sadeghinezhad E, Safaei MR
    ScientificWorldJournal, 2014;2014:369593.
    PMID: 25254236 DOI: 10.1155/2014/369593
    Thermal characteristics of turbulent nanofluid flow in a rectangular pipe have been investigated numerically. The continuity, momentum, and energy equations were solved by means of a finite volume method (FVM). The symmetrical rectangular channel is heated at the top and bottom at a constant heat flux while the sides walls are insulated. Four different types of nanoparticles Al2O3, ZnO, CuO, and SiO2 at different volume fractions of nanofluids in the range of 1% to 5% are considered in the present investigation. In this paper, effect of different Reynolds numbers in the range of 5000 < Re < 25000 on heat transfer characteristics of nanofluids flowing through the channel is investigated. The numerical results indicate that SiO2-water has the highest Nusselt number compared to other nanofluids while it has the lowest heat transfer coefficient due to low thermal conductivity. The Nusselt number increases with the increase of the Reynolds number and the volume fraction of nanoparticles. The results of simulation show a good agreement with the existing experimental correlations.
    Matched MeSH terms: Hydrodynamics
  9. Othman N, Kamarudin SK, Takriff MS, Rosli MI, Engku Chik EM, Meor Adnan MA
    ScientificWorldJournal, 2014;2014:619474.
    PMID: 25170524 DOI: 10.1155/2014/619474
    This paper presents the preliminary steps required for conducting experiments to obtain the optimal operating conditions of a hybrid impeller mixer and to determine the residence time distribution (RTD) using computational fluid dynamics (CFD). In this paper, impeller speed and clearance parameters are examined. The hybrid impeller mixer consists of a single Rushton turbine mounted above a single pitched blade turbine (PBT). Four impeller speeds, 50, 100, 150, and 200 rpm, and four impeller clearances, 25, 50, 75, and 100 mm, were the operation variables used in this study. CFD was utilized to initially screen the parameter ranges to reduce the number of actual experiments needed. Afterward, the residence time distribution (RTD) was determined using the respective parameters. Finally, the Fluent-predicted RTD and the experimentally measured RTD were compared. The CFD investigations revealed that an impeller speed of 50 rpm and an impeller clearance of 25 mm were not viable for experimental investigations and were thus eliminated from further analyses. The determination of RTD using a k-ε turbulence model was performed using CFD techniques. The multiple reference frame (MRF) was implemented and a steady state was initially achieved followed by a transient condition for RTD determination.
    Matched MeSH terms: Hydrodynamics*
  10. Naz MY, Sulaiman SA, Ariwahjoedi B, Ku Shaari KZ
    ScientificWorldJournal, 2013;2013:796081.
    PMID: 24307881 DOI: 10.1155/2013/796081
    The hot water sprays are an important part of many industrial processes, where the detailed knowledge of physical phenomena involved in jet transportation, interaction, secondary breakup, evaporation, and coalescence of droplets is important to reach more efficient processes. The objective of the work was to study the water spray jet breakup dynamics, vortex cloud formation, and droplet size distribution under varying temperature and load pressure. Using a high speed camera, the spray patterns generated by axisymmetric full cone nozzles were visualized as a function water temperature and load pressure. The image analysis confirmed that the spray cone angle and width do not vary significantly with increasing Reynolds and Weber numbers at early injection phases leading to increased macroscopic spray propagation. The formation and decay of semitorus like vortex clouds were also noticed in spray structures generated at near water boiling point temperature. For the nozzle with smallest orifice diameter (1.19 mm), these vortex clouds were very clear at 90°C heating temperature and 1 bar water load pressure. In addition, the sauter mean diameter (SMD) of the spray droplets was also measured by using Phase Doppler Anemometry (PDA) at different locations downstream of the nozzle exit. It was noticed that SMD varies slightly w.r.t. position when measured at room temperature whereas at higher temperature values, it became almost constant at distance of 55 mm downstream of the nozzle exit.
    Matched MeSH terms: Hydrodynamics*
  11. Mathew MJ, Sautter B, Ariffin EH, Menier D, Ramkumar M, Siddiqui NA, et al.
    Sci Total Environ, 2020 Mar 01;706:135963.
    PMID: 31862602 DOI: 10.1016/j.scitotenv.2019.135963
    Current worldwide projections of sea-level rise show a staggering increase in water level of up to 2 m by 2100 owing to global warming exacerbated by anthropogenically induced climate change. While amplified rates of sea-level rise is an immense hazard to coastal communities, storm surges are expected to increase in intensity and frequency making it an equally significant threat to coastal populations. In France, these hazards are not uncommon with records of extreme tempests every thousand years in the Holocene. Despite these recurring devastating events, in the Bay of Saint-Brieuc, Brittany, legislated laws for coastal management do not entirely focus on protecting littoral zones from such calamities. 130,739 people are concentrated in 21 municipalities with major cities located at close proximity to the shoreline with numerous socio-economic activities, which increases the vulnerability of the coastal population and infrastructures; thus, affirming the indispensable need of a thorough vulnerability assessment. Here, we conduct a mechanistic appraisal of the vulnerability of the bay considering thirteen parameters within three governing sub-systems that demonstrate the multidimensional dynamics in these municipalities. In the occasion of an extreme climatic event, our results of total vulnerability show risks in the sub-systems highlighting erosional processes due to augmented hydrodynamics, socio-economic and administrative vulnerabilities associated with anthropogenic development. Eight municipalities of the bay portray moderate to very high vulnerability and the remaining exhibits a lower risk; however, not devoid of high vulnerabilities for certain sub-systems. We posit that a more accurate fit for predicting the total vulnerability of the region can be achieved by exclusively integrating physical-natural and administrative sub-system vulnerabilities. We propose generic but requisite recommendations for Integrated Coastal Zone Management such as surveillance of urban development along the coast, implementation of coastal defense systems and appropriate industrial corridors to attenuate and dispose hazardous refuse.
    Matched MeSH terms: Hydrodynamics
  12. Ul-Haque A, Asrar W, Omar AA, Sulaeman E, Mohamed Ali JS
    J Exp Biol, 2015 Apr 15;218(Pt 8):1270-1.
    PMID: 25911735 DOI: 10.1242/jeb.117556
    Matched MeSH terms: Hydrodynamics
  13. Alvankarian J, Majlis BY
    Sensors (Basel), 2015 Nov 24;15(11):29685-701.
    PMID: 26610519 DOI: 10.3390/s151129685
    The adjustable microfluidic devices that have been developed for hydrodynamic-based fractionation of beads and cells are important for fast performance tunability through interaction of mechanical properties of particles in fluid flow and mechanically flexible microstructures. In this review, the research works reported on fabrication and testing of the tunable elastomeric microfluidic devices for applications such as separation, filtration, isolation, and trapping of single or bulk of microbeads or cells are discussed. Such microfluidic systems for rapid performance alteration are classified in two groups of bulk deformation of microdevices using external mechanical forces, and local deformation of microstructures using flexible membrane by pneumatic pressure. The main advantage of membrane-based tunable systems has been addressed to be the high capability of integration with other microdevice components. The stretchable devices based on bulk deformation of microstructures have in common advantage of simplicity in design and fabrication process.
    Matched MeSH terms: Hydrodynamics
  14. Hassan MA, Mahmoodian R, Hamdi M
    Sci Rep, 2014;4:3724.
    PMID: 24430621 DOI: 10.1038/srep03724
    A modified smoothed particle hydrodynamic (MSPH) computational technique was utilized to simulate molten particle motion and infiltration speed on multi-scale analysis levels. The radial velocity and velocity gradient of molten alumina, iron infiltration in the TiC product and solidification rate, were predicted during centrifugal self-propagating high-temperature synthesis (SHS) simulation, which assisted the coating process by MSPH. The effects of particle size and temperature on infiltration and solidification of iron and alumina were mainly investigated. The obtained results were validated with experimental microstructure evidence. The simulation model successfully describes the magnitude of iron and alumina diffusion in a centrifugal thermite SHS and Ti + C hybrid reaction under centrifugal acceleration.
    Matched MeSH terms: Hydrodynamics
  15. Tan MK, Siddiqi A, Yeo LY
    Sci Rep, 2017 07 27;7(1):6652.
    PMID: 28751783 DOI: 10.1038/s41598-017-07025-x
    The Miniaturised Lab-on-a-Disc (miniLOAD) platform, which utilises surface acoustic waves (SAWs) to drive the rotation of thin millimeter-scale discs on which microchannels can be fabricated and hence microfluidic operations can be performed, offers the possibility of miniaturising its larger counterpart, the Lab-on-a-CD, for true portability in point-of-care applications. A significant limitation of the original miniLOAD concept, however, is that it does not allow for flexible control over the disc rotation direction and speed without manual adjustment of the disc's position, or the use of multiple devices to alter the SAW frequency. In this work, we demonstrate the possibility of achieving such control with the use of tapered interdigitated transducers to confine a SAW beam such that the localised acoustic streaming it generates imparts a force, through hydrodynamic shear, at a specific location on the disc. Varying the torque that arises as a consequence by altering the input frequency to the transducers then allows the rotational velocity and direction of the disc to be controlled with ease. We derive a simple predictive model to illustrate the principle by which this occurs, which we find agrees well with the experimental measurements.
    Matched MeSH terms: Hydrodynamics
  16. Kohilavani Naganthran, Roslinda Nazar, Ioan Pop
    Sains Malaysiana, 2018;47:1069-1076.
    This study offers the numerical solutions for the problem of mixed convection stagnation-point flow along a permeable
    vertical flat plate in an Oldroyd-B fluid. The present investigation considers the effects of thermal radiation and heat
    generation/absorption in the fluid flow. The similarity transformation simplifies the complex model and the bvp4c function
    generates the numerical solutions according to the variations in the governing parameters. A higher degree of shrinking
    hastens flow separations. The dual solutions are visible in the range of buoyancy opposing flow. The results from this study
    may be useful for the scientist to understand the behaviour of the dilute polymer solutions in the industrial applications,
    for example, the drag reduction in pipe flows.
    Matched MeSH terms: Hydrodynamics
  17. Anuar Jamaludin, Roslinda Nazar, Ioan Pop
    Sains Malaysiana, 2018;47:2213-2221.
    In this study, the effects of suction and injection on the mixed convection flow of a nanofluid, over a moving permeable
    vertical plate were discussed. A similarity variable was used to transform the governing equations to the ordinary
    differential equations, which were then solved numerically using the bvp4c programme from MATLAB. Dual solutions
    (upper and lower branches) were found within a certain range of the mixed convection parameter in assisting and
    opposing flow regions. A stability analysis was implemented to confirm that the upper branch solution was stable, while
    the lower branch solution was unstable.
    Matched MeSH terms: Hydrodynamics
  18. Kamangar S, Nik-Ghazali N, Badarudin A, Ameer Ahamad N, Irfan Anjum Badruddin, Govindaraju K, et al.
    Sains Malaysiana, 2017;46:1923-1933.
    The present work was carried out to investigate the blood flow behavior and the severity of blockage caused in the
    arterial passage due to the different geometries such as elliptical, trapezium and triangular shapes of stenosis. The study
    was conducted with respect to various sizes of stenosis in terms of 70%, 80% and 90% area blockage of the arterial
    blood flow. The study was carried out numerically with the help of advance computational fluid dynamic software. It
    was found that the shape of the stenosis plays an important role in overall pressure drop across the blockage region
    of artery. The highest level of pressure drop was observed for trapezoidal shape of stenosis followed by elliptical and
    then by triangular shaped stenosis. The wall shear stress across the stenosis is great for trapezoidal shape followed by
    triangular and elliptical stenosis for same blockage area in the artery.
    Matched MeSH terms: Hydrodynamics
  19. Liyana Mohd Ali Napia, Faizal Mohamed, Hur Munawar Kabir Mohd, Intan Syakeela Ahmad Bastamam, Shamellia Sharin, Norsyahidah Mohd Hidzir, et al.
    Sains Malaysiana, 2018;47:1235-1240.
    Unilamellar liposomes composed of dipalmitoylphosphatidylcholine (DPPC) were prepared by the reverse-phase
    evaporation method and extrusion through a polycarbonate membrane filter. Liposomes at 0.7 mg/mL lipid concentration
    in deionized water were exposed to gamma irradiation at a dose in the range 0.5 to 25 kGy. Gamma irradiation of
    liposomes resulted in the degradation of DPPC lipids into free fatty acids, lysophosphatidylcholine and 1,2-palmitoylphosphatidic
    acid (DPPA). The effect of gamma irradiation towards the physical stability of liposomes was investigated
    by means of dynamic light scattering (DLS), transmission electron microscopy (TEM) and zeta potential analysis. From
    the DLS analysis, no significant changes were observed in the hydrodynamic size of liposomes. TEM images indicate that
    the liposomes surface became smoother and rounder as higher irradiation doses were applied. Zeta potential analysis
    showed that gamma irradiation of DPPC liposomes at radiation doses as low as 0.5 kGy resulted in a drastic rise in the
    magnitude of the zeta potential. The results also demonstrate that gamma irradiation of liposomes suspension enhanced
    the overall stability of liposomes. Hence, it can be concluded that gamma irradiation on DPPC liposomes may potentially
    produce liposomes with higher stability.
    Matched MeSH terms: Hydrodynamics
  20. Norfifah Bachok, Anuar Ishak
    Sains Malaysiana, 2011;40:1297-1300.
    This paper presents a numerical analysis of a stagnation-point flow towards a nonlinearly stretching/shrinking sheet immersed in a viscous fluid. The stretching/shrinking velocity and the external flow velocity impinges normal to the stretching/shrinking sheet are assumed to be in the form U ~ xm, where m is a constant and x is the distance from the stagnation point. The governing partial differential equations are converted into ordinary ones by a similarity transformation, before being solved numerically. The variations of the skin friction coefficient and the heat transfer rate at the surface with the governing parameters are graphed and tabulated. Different from a stretching sheet, it is found that the solutions for a shrinking sheet are non-unique for m > 1/3.
    Matched MeSH terms: Hydrodynamics
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links