Nuclear grade (high-purity) graphite for fuel element and moderator material in Advanced Gas
Cooling Reactors (AGR) displays large scatter in strength and a non-linear stress-strain response from the damage accumulation. These responses can be characterized as quasi-brittle behaviour. Current assessments of fracture in core graphite components are based on the linear elastic approximation and thus represent a major assumption. The quasi-brittle behaviour gives challenge to assess the real nuclear graphite component. The selected test method would help to bridge the gap between microscale to macro-scale in real reactor component. The small scale tests presented here can contribute some statistical data to manifests the failure in real component. The evaluation and choice of different solution design of biaxial test will be discussed in this paper. The ball on-three ball test method was used for assessment test follows by numerous of analytical method. The results shown that biaxial strength of the EY9 grade graphite depends on the method used for evaluation. Some of the analytical methods use to calculate biaxial strength were found not to be valid and therefore should not be used to assess the mechanical properties of nuclear graphite.
Colour is one of the most important traits in orchids and has created great interest in breeding programmes. Gamma irradiation is an alternative way for generation of somaclonal variation for new flower colours. Phenotypic changes are usually observed during screening and selection of mutants. Understanding of targeted gene expression level and evaluation of the changes facilitate in the development of functional markers for selection of desired flower colour mutants. Four Dendrobium orchid sequences (NCBI accessions: AM490639, AY41319, FM209429 and DQ462460) were selected to design gene specific primers based on information for chalcone synthase (CHS) from NCBI database. Quantitative real-time PCR (qPCR) was used to understand flower colour expression quantitatively derived from the CHS gene activities in different flower tissues (petal and sepal) from control Dendrobium Sonia (red purple), mutant DS 35-1/M (purple pink) and mutant DS 35-WhiteA. It was found that expression of CHS gene was highest in sepals of white flowers and lowest in both sepals and petals of purple pink flowers. Genomic DNA was amplified and PCR products were sequenced, aligned and compared. Sequence variations of CHS partial gene in Dendrobium Sonia mutants with different flower colour showed that two protein positions have been changed as compared to the control. These non-synonymous mutations may have contributed to the colour alterations in the white and purple pink mutants. This paper describes important procedures to quantify gene expression such as RNA isolation (quantity and quality), cDNA synthesis and primer design steps for CHS genes.
Chrysanthemum morfolium is an important temperate cut flower and potted plant for Malaysian local market and exporter. Considering chrysanthemum as a popular vegetatively propagated ornamental plant, induce mutations for breeding purposes are more beneficial. Several of physical mutagens have been used in mutation breeding including x-rays, gamma rays and ion beams. Gamma rays and ion beams are from two different linear energy transfer (LET) which are low and high, respectively. The objective of this study was to compare the effectiveness of acute gamma and ion beam irradiation in generating flower colour mutations on nodal explants of Chrysanthemum morifblium cv. Reagan Red'. The nodal explants were irradiated with acute gamma (0, 10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 110 and 120 Gy) and ion beam (0, 0.5, 1.0, 2.0, 3.0, 5.0, 8.0, 10, 15, 20 and 30 Gy). The optimal dose for in vitro shoot regeneration using acute gamma was in the range of 10 to .15.0Gy and for ion beam was between 3.5 to 4.OGv. Relative biological effectiveness for ion beam was found 3.75 higher than the acute gamma. The regenerated plantlets were planted in the greenhouse at MARDI, Cameron Highland for morphological screening. The highest frequency of flower colour mutation for acute gamma was 77.8% whilst for ion beam were between 42.3 to 58.3%.
Laboratory radiotracer experiment was performed to study the bioaccumulation of 109Cd and 134Cs in the Malaysian common fish White seabass (Lates calcarifer). The aim of this study was to compare the biokinetics of uptake these two contrasting radionuclides by White seabass in laboratory condition scale. Experiments were designed to determine the processes controlling uptake of both radionuclides following exposure via seawater. In this study, the curve shapes of the uptake kinetic of 109Cd and 134Cs in White seabass were slightly linear and gradually increased with increasing of exposure time but were not reach equilibrium in the period of the study of 21 days. This phenomenon can be concluded that radioelement concentrations of 109Cd and 134Cs; and exposure duration of this experiment may not adequately to reach steady-state condition for uptake kinetic of those radioelements in White seabass. Furthermore, this was indicated that the uptake rate of 109Cd was 1.79 times faster than 134Cs due to some factors may probably influenced the output of this experiment such as different element accumulation strategies, physiological, behavior of radioelements, etc.
IAEA Soil-6 is a reference material with a certified value for 226Ra fall between 69.6 – 93.4 Bq/kg at 95% confidence level. This material has been used as a sample and performed repeat measurement weekly between years 2006 – 2009 using a same gamma spectrometry system. The activity concentration of this material is calculated automatically using the operational commercial software and compared with activity obtained from the manual calculation. Study found that only 76.9%, 64.1%, 56.3%, and 79.3% of the results from the software calculation lie within the confidence level for year 2006, 2007, 2008 and 2009, respectively. However, u-score calculation revealed that 94.9 %, 89.7%, 79.2% and 84.9% data set have no significant bias (u < 2.58) for year 2006, 2007, 2008 and 2009, respectively. On the other hand, all manual calculation data were found to be within the 95 % confidence level. Factors suspected to cause differences between these two approaches were discussed here. Manually peak search, marking and calculation still remains as the preferred option for calculating the gamma radionuclides activity unless limitations of the spectrum analysis software, as described in this paper can be resolved/improved upon.
Mechanical properties of blended polyethylene (PE) containing the antioxidant Irganox 1010 and the UV-absorber Tinuvin 326 were studied for future use as radiation capsule material for the TRIGA Mark II research reactor. High density and low density polyethylene were blended with the additives and tested for elongation at break, impact strength and gel content, before and after irradiation inside the nuclear reactor. Characterization via FTIR as well as determination of crystallization and melt transition temperatures through DSC were also conducted. It was found that the addition of the antioxidant at different amounts (from 0 to 4 phr) had various effects on the properties of the blended PE, with 0 phr being the amount at which there was the biggest increase in elongation at break and impact strength, post-irradiation.
Many times a year natural gas transmission and distribution companies need to make new connections to pipelines to expand or modify their existing system through hot tapping procedure. This procedure involves the installation of a new pipeline connection while the pipeline remains in service, flowing natural gas under pressure. The hot tap procedure includes attaching a branch connection and valve on the outside of an operating pipeline, and then cutting out the pipe-line wall within the branch and removing the wall section, which is called object of coupon through the valve. During the hot tapping process a critical problems occurred when a coupon fell into the mother pipeline. To overcome this problem, a gamma-ray absorption technique was chosen whereby a mapping technique will be done to detect the coupon position. The technique is non-destructive as it applies Co-60 (5mCi) as a radioisotope sealed source to emit gamma radiation and a NaI(Tl) scintillation as detector. The result provided a visible representation of density profile inside pipeline where the coupon location can be located. This paper provides the detail of the technique used and presents the result obtained.
In industrial plants such as electricity generating, petroleum, chemical and petrochemical plants, pipelines are used extensively to transport liquid from one location to another. In radiation vulcanization of natural rubber latex (RVNRL) plants, pipelines are also used to transport latex to storage tank. During one of its maintenance activities, a pipeline intelligent gauge (PIG) that was used to monitor pipe integrity jammed inside the pipe causing interruption to its operation or loading activities. Sealed source technology was utilized to determine the location of jammed PIG in the pipeline. Fast neutrons from a 50 mCi Americium Beryllium (AmBe241), with energy range between 0.5 to11 MeV, were used for the study. Helium 3 (He3) detector was used to detect slow neutrons having a range of energy of 30 eV- 0.5 MeV. The investigation was carried out using neutron backscatter technique scanner. By adopting back-scattered technique, the location of jammed PIG in the pipeline has been successfully determined.
Detection and analysis of resin is particularly significant since the commercial value of agarwood is related to the quantity of resins that are present. This article explores the potential of a scanning electron microscope in combination with new non-destructive 3D visualization technique, X-ray micro-computed tomography, as imaging tools to visualize micro-structure resin in agarwood. These techniques were used to compare two samples of agarwood chips: high grade and low grade. From the results, it can be concluded that a wood cell filled with resin deposit have a higher attenuation. It can be shown that the combination of scanning electron microscopy and micro-CT can offer high resolution images concerning the localization and structure of resin inside Agarwood. While the second allows the 3D investigation of internal structure of agarwood, the first technique can provide details 2D morphological information. These imaging techniques, although sophisticated can be used for standard development especially in grading of agarwoodlbr commercial activities.
Flow measurement is a critical element for liquid resources monitoring for various applications in many industrial systems. The purposes of the study are to determine the flow rate of liquid system in flow rig using radiotracer techniques and to compare the result with that obtained by the conventional flow meters. The flow rig consists of 58.7m long and 20cm diameter pipeline that can accommodate about 0.296m3 of liquid. Tap water was used as liquid flow in pipeline and conventional flow meters were also installed at the flow rig. Radiotracer was injected as a sharp pulse into the inlet p.peline. The pulse was monitored at the inlet and various points along the outlet pipeline using collimated scintillation detector. The peak to peak and total count methods were applied for radiotracer techniques and showed the comparable results with conventional flow meter.
A study to assess the concentration of radionuclides in spent resins of the PUSPATI TRIGA Mark II reactor coolant purification system has been carried out. Fresh spent resins collected and analysed in May 2010, after the changing of leaked heat exchanger in Sept. 2009 was found to contain 24Na, 122Sb, 51Cr, 124Sb, 58Co, 65Zn, 54Mn and 60Co. Old spent resins removed in 2001 and 2002 but analysed in 2010 indicated the presence of 60Co and 152Eu as radionuclides with half-lives of < 1 year might have already been decayed out. These results can be used to establish radionuclide inventory of the spent resins as part of radiation protection programme.
One of the most prevailing issues in the operation of Nuclear Reactor is the safety of the system. Worldwide publicity on a few nuclear accidents as well as the notorious Hiroshima and Nagasaki bombing have always brought about public fear on anything related to nuclear. Most findings on the nuclear reactor accidents are closely related to the reactor cooling system. Thus, the understanding of the behaviour of reactor cooling system is very important to ensure the development and improvement on safety can be continuously done. Throughout the development of nuclear reactor technology, investigation and analysis on reactor safety have gone through several phases. In the early days, analytical and experimental methods were employed. For the last three decades ID system level codes were widely used. The continuous development of nuclear reactor technology has brought about more complex system and processes of nuclear reactor operation. More detailed dimensional simulation codes are needed to assess these new reactors. This paper discusses the development of 3D CFD usage in nuclear reactor safety analysis worldwide. A brief review on the usage of CFD at Malaysia's Reactor TRIGA PUSPATI is also presented.
Heel Effect is the well known phenomena in x-ray production. It contributes the effect to image
formation and as well as scattered radiation. But there is paucity in the study related to heel effect.
This study is for mapping and profiling the dose on the surface of water phantom by using mobile
C-arm unit Toshiba SXT-1000A. Based on the result the dose profile is increasing up to at least
about 57% from anode to cathode bound of the irradiated area. This result and information can be
used as a guide to manipulate this phenomenon for better image quality and radiation safety for
this specific and dedicated fluoroscopy unit.
Carbon-11 labeled radiotracers, such as 11C-acetate and
11C-palmitate are widely used in positron
emission tomography (PET) for noninvasive evaluation of myocardial metabolism under varied
physiological conditions.These tracers are attractive probes of tissue physiology, because they are
simply radiolabled versions of the native biochemical substrates. One of the major metabolites
generated by these tracers upon the administration is 11CO2 produced via the citric acid cycle. In
quantitative modeling of
11C-acetate and
11C-palmitate PET data, the fraction of blood
11C
radioactivity present as
11CO2 needs to be measured to obtain a correct radiotracer arterial
input function. Accordingly, the literature describes a method whereby the total blood
11C-activity
is counted in blood samples treated with base solution, while the fraction of
1 1CO2 is measured
after the blood is treated with acid followed by a 10 minutes gas-purge. However, a detailed
description of the experimental validation of this method was not provided. The goal of this study
was to test the reliability of a 10 minute gas purging method used to assay
11CO2 radioactivity in
blood
Stevia rebaudiana Bertoni is a perennial herb that belongs to the family of Asteraceae. It is a
natural sweetener plant known as sweet leaf, which is estimated to be 300 times sweeter than cane
sugar. In this study, micropropagation and in vitro mutagenesis of this natural herb was
successfully conducted. It was found that shoot tips on MS medium supplemented with 1 mg/l
Kinetin showed the highest shoot induction and multiplication after 3 weeks of culture
(5.50±1.95a). Radiosensitivity test was conducted to identify the dose that killed 50% of the
irradiated explants (LD50) for in vitro stevia shoots and to select effective doses to be used for the in
vitro mutagenesis. Shoot tips were irradiated with acute and chronic gamma radiation at 0, 10, 20,
30, 40, 60, and 80Gy. At 60 Gy and 80 Gy, all treated shoot tips were not survived. In this study,
LD50 for the stevia was estimated at 29 Gy for acute irradiation and 45 Gy for chronic irradiation.
The effective doses were selected at 10, 20, 30 and 40 Gy. These selected doses were applied for the
in vitro mutagenesis of the stevia shoots
On March 11, 2011, a serious accident occurred in Daiichi nuclear reactor plant, Fukushima,
Japan which caused radioactive materials been released into the atmosphere in the form of
aerosols and dust particles. Sea water around the plant was also found contaminated with high
radioactivity readings. These radioactive materials could be transported by the winds and ocean
current across international borders and cannot be controlled by human. Thus, a continuous
monitoring activity of radionuclide content in the air and sea water needs to be conducted by the
authorities. In addition to radioactivity monitoring, Malaysia should also control the entry of
contaminated food in order to prevent radionuclide ingestion by human. The radionuclide 131I,
134Cs and 137Cs were used as a measure of pollution levels and counted with gamma spectrometry
using standard analysis method suggested by AOAC International. In this paper, details description
of the role of Radiochemical and Environment Group, Nuclear Malaysia who’s responsible in
analyzing the radioactivity in the food samples due to Fukushima Daiichi, Japan accident was
included. The radioactivity limit adopted and analysis results from this monitoring were discussed
The assessment of surface dose is essential in radiotherapy to avoid deterministic effect or to
reduce the severity of side effects from radiation treatment. In this study, the surface dose for breast
cancer radiotherapy was measured using two types of dosimeter; Thermoluminescent Dosimeter
(TLD) and Optically Stimulated Luminescent Dosimeter (OSLD). The study was performed on the
left breast of female Alderson Radiation Therapy (ART) phantom. The treatment planning was
carried out on the ART phantom to determine the homogeneity of dose distribution within the target
organ is complied with the tolerance limits of 95% to 107% as recommended by the International
Commission on Radiation Units and Measurements (ICRU)’s Report No. 50. From the treatment
planning result, the phantom then was irradiated with 267 cGy dose per fraction for two beam
fields; medial tangential and lateral tangential fields using a 6 MV photon beam produced from
three-dimensional (3D) conformal radiotherapy. Result shows that the OSLD provides 25.7% and
23.5% higher surface dose compared to TLD for medial tangential and lateral tangential fields,
respectively. This condition may be due to higher effective point of measurement and angular
dependence of the OSLD compared to TLD. As a conclusion, suitable dosimeter should be selected
to ensure accurate estimation of surface dose could be made thus reduction of skin reaction to
patient could be achieved.
This paper studies about water obtained from fish pond of fisheries research centre. Usual water
quality parameters such as pH, COD, Turbidity and Ammonia content were analyzed before and
after irradiation. Electron beam irradiation was used to irradiate the water with the dose 100 kGy,
200 kGy and 300 kGy. Only high dose was applied on this water as only a limited amount of
samples was supplied. All the parameters indicated a slight increase after irradiation except for the
ammonia content, which showed a gradual decrease as irradiation dose increases. Sample
condition was changed before irradiation in order to obtain more effective results in the following
batch. The water sample from fisheries was diluted with distilled water to the ratio of 1:1.This was
followed with irradiation at 100 kGy, 200 kGy and 300 kGy. The results still showed an increase in
all parameters after irradiation except for ammonia content. For the following irradiation batch,
the pH of the sample was adjusted to pH 4 and pH 8 before irradiation. For this sample the
irradiation dose selected was only 100 kGy. A higher value of ammonia was observed for the
sample with pH 4 after irradiation. Other parameters were almost the same as the first two batches
Haruan or Channa striatus is source of protein that is widely consumed in the region and its extract
is well known for having medical values. It is of great advantage if this product could be taken
orally rather than by injection because the oral route of drug delivery is still preferred by the vast
majority of patients. However protein and peptides can be denatured or degraded by the acidic pH
of the stomach and the presence of endogenous enzymes. In order to protect or prevent digestion
and degradation of the protein in the stomach and to ensure the protein reaches the gastro
intestinal (GI) tract, Carboxymethyl Starch (CMS) nanogel system was developed using electron
irradiation method. However stability of HTE during the irradiation process needed to be studied
before being developed further. In this study, the HTE was irradiated using electron beams. Its
stability was analysed in terms of physical and chemical changes by looking at colour difference,
melting point by using Differential Scanning Calorimetry (DSC) and molecular bonds by using
Fourier Transform Infrared (FTIR) respectively. The results of this study were that no apparent
colour difference was observed with HTE before and after irradiation. These observations were
supported by the FTIR and DSC results that showed that there were no changes in molecular bonds
and melting point, compared between no irradiation and irradiation HTE during electron
irradiation up to 10 kGy. Statistically the test showed no significant difference at p < 0.005 between
melting temperatures.
Anthropogenic airborne depositions of 210Po,
210Pb and 210Po/210Pb in the mosses and surface soils
collected at the vicinity of a coal-fired power plant were studied. The purpose of the study was to
determine activity concentrations of 210Po,
210Pb and 210Po/210Pb for assessing their variation
accumulation in the mosses and surface soils collected at the vicinity of a coal-fired power plant.
Other purposes were to determine their concentration factor (CF) in relation to track the potential
source of those radionuclides and to identify most suitable moss species as a biological indicator
for atmospheric deposition contaminants. In this study, different species of moss Leucobryum
aduncum, Campylopus serratus, Syrrhopodon ciliates and Vesicularia montagnei were collected in
May 2011 at the area around 15 km radius from Tanjung Bin coal-fired power plant located in
Pontian, Johor. The activity concentrations of 210Po,
210Pb and 210Po/210Pb in mosses were in the
range of 76.81 ± 4.94 – 251.33 ± 16.33 Bq/kg dry wt., 54.37 ± 3.38 – 164.63 ± 11.64 Bq/kg dry wt.
and 1.10 – 2.00, respectively. Meanwhile the ranges for those radionuclides in the surface soil
were 33.53 ± 2.10 – 179.67 ± 12.15 Bq/kg dry wt., 20.55 ± 1.33 – 106.62 ± 6.64 Bq/kg dry wt. and
1.61 – 2.44, respectively. Corresponding high ability of Leucobryum aduncum to accumulate more
210Po and 210Pb, wide geographical distribution, most abundant and high CF, therefore, the
findings can be concluded this species was the most suitable as a biological indicator for
atmospheric deposition contaminants such as 210Po and 210Pb. Furthermore, it is clear the
accumulation of 210Po and 210Pb in mosses might be supplied from various sources of atmospheric
deposition such as coal-fired power plant operation, industrial, agriculture and fertilizer activities,
burned fuel fossil and forest; and other potential sources. Meanwhile, the