This study was conducted to evaluate the effect of the toxicity levels of the coagulation and flocculation process on raw and treated leachate using acute toxicity tests. Tin tetrachloride (SnCl4 ) and the Jatropha curcas (JC) seed were used as coagulant and coagulant aid to remove concentrated suspended solids, SS (534 mg/L), color (19,297 Pt-Co), and chemical oxygen demand (COD) (4188 mg/L) in a stabilized landfill leachate. The toxicity effects on local red tilapia fish (Oreochromis niloticus) were investigated, which involved three main steps, namely, acclimatization, range-finding test, and short-term definitive test. The presence of JC seed (0.9 g/L) as a flocculant reduced the dosage of SnCl4 from 11.1 to 8.5 g/L and exhibited good removals of 99.78%, 98.53%, and 74.29%, respectively, for SS, color, and COD. The toxicity test indicated that only five fish died in the first 12 h for the treated sample compared with seven deaths for untreated leachate. In 96 h, a total of 42 and 31 mortality rates were noted for the raw and treated leachate samples, respectively. The treated sample could reduce the toxicity effects to the tested tilapia fish and is safe to be discharged at appropriate dilution concentrations. PRACTITIONER POINTS: Coagulation-flocculation by Tin (IV) chloride and Jatropha Curcas (JC) was investigated. Almost complete reduction of SS was obtained at 8.5 g/L of SnCl4 and 0.9 g/L of JC as flocculant. The toxicity effect was evaluated using red tilapia (Oreochromis niloticus) fish as the indicator. Treated leachate was considered acceptable as the number of dead fish was lower than the untreated leachate.
Landfill leachate can threaten the environment and human life. Therefore, this study aims to investigate the efficiency of ozone (O3 ), O3 with zirconium tetrachloride (O3 /ZrCl4 ), and O3 with tin tetrachloride (O3 /SnCl4 ) in remediating the stabilized anaerobic landfill leachate (SAL) from Alor Pongsu, Perak. Hydroxyl radical (OH•) is an important oxidizing agent in the ozonation process. Its presence was tested using tert-butyl alcohol. Results showed that using ZrCl4 and SnCl4 in ozonation boosted the generation of hydroxyl radical, thereby enhancing the oxidation process and pollutant removal inside the sample. The O3 /ZrCl4 mix at chemical oxygen demand (COD) to ZrCl4 ratio of 1:1.5, pH 8-9, and 90-min reaction time resulted in the highest reduction rates of COD and color at 91.9% and 99.6%, respectively. All results demonstrated that the optimum performance occurred at alkaline conditions (pH > 8), proving that OH radicals primarily oxidized the pollutants through an indirect reaction pathway. The biodegradability (biochemical oxygen demand/COD) ratio was also considerably improved from 0.02 (raw) to 0.37 using O3 /ZrCl4 , compared with using O3 alone and using O3 /SnCl4 , which only recorded 0.23 and 0.28, respectively, after the treatment. The study demonstrated that O3 /ZrCl4 was the most efficient combination. PRACTITIONER POINTS: The O3 /ZrCl4 recorded the highest COD and color removals. The O3 /ZrCl4 combination also recorded higher OH• concentrations. The biodegradability of leachate (BOD5 /COD ratio) improved from 0.02 to 0.37.
The Bio-Ecological Drainage System (BIOECODS) is a sustainable drainage (SUDS) to demonstrate the 'control at source' approaches for urban stormwater management in Malaysia. It is an environmentally friendly drainage system that was designed to increase infiltration, reduce peak flow at outlet, improve water quality, through different BMPs, such as grass swale, retention pond, etc. A special feature of BIOECODS is ecological swale with on-line subsurface detention. This study attempted to create a model of ecological swale with on-line subsurface conveyance system with InfoWorks SD. The new technique has been used Storm Water Management Model (SWMM) model to describe overland flow routing and Soil Conservation Service Method (SCS) used to model infiltration or subsurface flow. The modeling technique has been proven successful, as the predicted and observed closely match each other, with a mean error of 4.58 to 7.32%. The calibrated model then used to determine the ratio of the flow exchange between the surface and subsurface drainage system. Results from the model showed that the runoff ratio exchange between the surface and subsurface is 60 to 90%.
The spatio-temporal variability of water quality associated with anthropogenic activities was studied for the Bertam River and its main tributaries within the Bertam Catchment, Cameron Highlands, Malaysia. A number of physico-chemical parameters of collected samples were analyzed to evaluate their spatio-temporal variability. Nonparametric statistical analysis showed significant temporal and spatial differences (p < 0.05) in most of the parameters across the catchment. Parameters except dissolved oxygen and chemical oxygen demand displayed higher values in rainy season. The higher concentration of total suspended solids was caused by massive soil erosion and sedimentation. Seasonal variations in contaminant concentrations are largely affected by precipitation and anthropogenic influences. Untreated domestic wastewater discharge as well as agricultural runoff significantly influenced the water quality. Poor agricultural practices and development activities at slope areas also affected the water quality within the catchment. The analytical results provided a basis for protection of river environments and ecological restoration in mountainous Bertam Catchment.
The effect of physical shearing on the attachment of six Pseudomonas aeruginosa strains and six Burkholderia cepacia strains to glass, stainless steel, polystyrene and Teflon® was determined. A significant (p < 0.05) decrease in hydrophobicity was apparent for all P. aeruginosa strains (17-36%) and B. cepacia, MS 5 (20%) after shearing. A significant (p < 0.05) decrease in attachment of some P. aeruginosa (0.2-0.5 log CFU/cm2) and B. cepacia (0.2-0.4 log CFU/cm2) strains to some surface types was apparent after shearing. Significant (p < 0.05) correlation was observed for both numbers of flagellated cells and hydrophobicity against attachment to glass, stainless steel and polystyrene for P. aeruginosa while only hydrophobicity showed significant correlation against the same surfaces for B. cepacia. Scanning electron microscopy and protein analysis showed that shearing removed surface proteins from the cells and may have led to the observed changes in hydrophobicity and attachment to abiotic surfaces.
Produced water (PW) has been generated in a huge amount representing the largest volume waste stream. Membrane technology has found a leading ability in treating PW due to its significant advantages, such as lower cost, easy installation, and being environmentally friendly. Mixed matrix membranes (MMMs) have received significant research interest due to their flexibility, multifunctionality enhances the membrane performance with increasing selectivity, permeability, robustness, mechanical strength, and resistance to fouling. This mini-review paper identifies the utilization of different membranes for treating PW. It also gives a review of different types of MMMs with specific fillers for the application of PW treatment. Lastly, some methods to enhance the performance of mixed matrix membranes have been highlighted. The issues and challenges in membranes are also discussed. PRACTITIONER POINTS: Mixed matrix membranes (MMMs) are a potential membrane type for PW treatment. This mini-review paper identifies the use of several membranes to treat PW. It also examined various types of MMMs containing specific fillers for the application of PW treatment. Methods for improving the performance of mixed matrix membranes have been highlighted, including the use of novel materials, surface modification, and cross-linking. The issues and challenges in membranes are also discussed.
The combination of UV and water-soluble Fe(III) complexes is an effective method for generating Fe(II) in situ for activating advanced oxidation processes. This study explored the potential of Fe(III)-diethylenetriaminepentaacetic acid (Fe(III)-DTPA) and Fe(III)-ethylene glycol-bis(2-aminoethylether)-N,N,N',N'-tetraacetic acid (Fe(III)-EGTA) in activating the UV/persulfate (UV/PS) for sulfamethazine removal. The initial screening showed that Fe(III)-EGTA and Fe(III)-DTPA could significantly improve the rate of sulfamethazine removal. The optimum molar ratios of persulfate to Fe(III)-DTPA and Fe(III)-EGTA were 100:1 and 100:2.5. The predicted percentage of sulfamethazine removal under the optimized conditions, obtained using response surface methodology, was ~99% for both catalysts. The pH range of 6 to 8 did not significantly affect the performance of UV/PS in the removal of sulfamethazine. The percentage sulfamethazine removal in the selected water samples was ranged from 93.6% to 99.6%, agreeing with the predicted value. The performance of both catalysts in activating UV/PS is comparable with that of the frequently used Fe(III)-EDDS. PRACTITIONERS POINTS: The potential of Fe(III)-DTPA and Fe(III)-EGTA in activating UV/persulfate (UV/PS) was explored. Fe(III)-DTPA and Fe(III)-EGTA improved the performance of UV/PS in sulfamethazine removal. Fe(III)-DTPA and Fe(III)-EGTA are effective in catalyzing UV/PS under pH 6 to 8. The performance of Fe(III)-DTPA and Fe(III)-EGTA is comparable with well-studied Fe(III)-EDDS.
Groundwater is one of the alternatives to surface water that can be used for drinking water; however, it normally exists with high iron and manganese content. In this study, a column study was conducted to observe the elimination of iron (Fe) and manganese (Mn) in the groundwater under different retention times by using zeolite immobilized with iron-oxidizing bacteria (IOB). Rossellomorea sp., representing an IOB, was found from the isolation process and was further cultured in the laboratory for immobilization into the natural zeolite as replacement materials for the sand filter. When the zeolite assisted with the Rossellomorea sp. was used, the elimination of Fe and Mn were 99.34% and 88.92%, respectively, compared to the removal of Fe and Mn, which were 93.62% and 93.73%, respectively, for media without immobilization. The presence of Rossellomorea sp. enhances the Fe oxidation, resulting in high removal of Fe. The Thomas and Yoon-Nelson models were performed in both raw zeolite and zeolite with IOB. The total coliform (most probable number [MPN]) increased from 70.8 to 307.6 MPN/100 mL because of the Rossellomorea sp. present that promotes the growth of coliform bacteria. In conclusion, the immobilization of zeolite with IOB is a potential technique to extract the Fe and Mn in the groundwater. PRACTITIONER POINTS: Zeolite incorporated with Rossellomorea sp. has higher removal performance of Fe, whereas the removal of Mn reduced compared to the raw zeolite. The presence of Rossellomorea sp. enhances the oxidation of ferrous iron and improves the removal of Fe in the groundwater because the ferric iron is the priority ion to be exchanged. The removal of UV254 increase when Rossellomorea sp. present in the zeolite because the Rossellomorea sp. consume the natural organic matter as carbon source.
Malaysia encounters a consistent rise in the generation of solid waste and leachate on a daily basis. It should also be noted that leachate has a low degree of biodegradability (BOD5 /chemical oxygen demand [COD]), as shown by its BOD5 /COD ratio. Its high toxicity levels significantly threaten the environment, water bodies, and human well-being. High concentrations of COD, color, and ammoniacal nitrogen (NH3 -N) in leachate prevent this wastewater from being allowed to be discharged directly into the water body. Therefore, an effective process to remove the pollutant is desired. The aims of this study are to investigate the performance of ozonation with two metallic compounds, ZrCl4 and SnCl4 , and optimize their performance using response surface methodology (RSM). In this study, the performance of ozonation with ZrCl4 (O3 /ZrCl4 ) recorded better pollutant removals compared with the ozonation with tin tetrachloride (O3 /SnCl4 ), as seen in the removals of 99.8%, 93.5%, and 46.3% for color, COD, and NH3 -N, respectively. These removals were achieved by following the experimental model (optimum experiment condition) generated by RSM at O3 dosage of 31 g/m3 , COD and ZrCl4 dosage ratio (COD, mg/L/ZrCl4 , mg/L) of 1:1.35, with the pH solution of 8.78 and reaction time of 89 min. The R2 of each parameter for this model was recorded as 0.999 (COD), 0.999 (color), and 0.998 (NH3 -N), respectively. These data indicated that the model is well fitted as the predicted data by statistical calculation and in good agreement with the actual data. PRACTITIONER POINTS: The performance of O3 /ZrCl4 and O3 /SnCl4 was examined for remediate stabilized landfill leachate. The performance of O3 /ZrCl4 and O3 /SnCl4 was optimized using RSM, and a set of experimental models was generated and tested. O3 /ZrCl4 recorded the higher removal of COD, color, and NH3 -N compared with O3 /SnCl4 . At best condition, both methods recorded removal as 89% to 99.8% of pollutants in leachate and product clear effluent. This finding gives a new approach to treat landfill leachate effectively and efficiently.
Landfill leachate is well known as a hazardous byproduct from dumpling sites that has a negative impact on the environment and human life. Therefore, an effective treatment is imperative to overcome this issue. This research study investigates the effectiveness of zirconium tetrachloride (ZrCl4 ) and tin tetrachloride (SnCl4 ) as a coagulant in leachate treatment. Two parameters selected as a performance indicator in this study are color and chemical oxygen demand (COD). The data obtained showed that SnCl4 performed well as a coagulant with removal percentages of color and COD, which are 97% and 77%, respectively. Furthermore, the potential of integrated treatment using ozonation (O3 ) and the coagulation-flocculation process was also investigated. Four sequences of integrated treatment setup for this study were ozonation followed by jar test (ZrCl4 as a coagulant), ozonation followed by jar test (SnCl4 as a coagulant), jar test (ZrCl4 as a coagulant) followed by the ozonation process, and jar test (SnCl4 as a coagulant) followed by the ozonation process. The experimental data showed that the combination treatment of SnCl4 as a coagulant (jar test) followed by the ozonation process had recorded the highest removal of color (97.1%) and COD (88%) compared to other sequences. Moreover, the biodegradability ratio of this sequence also improved from 0.03 to 0.28, compared with other methods. Comparatively, integrated treatment is more effective in treating stabilized landfill leachate compared to the coagulation flocculation process alone. PRACTITIONER POINTS: Stabilized landfill leachate is difficult to be treated by natural coagulants or biological process. SnCl4 performed well as a coagulant in removing COD and colour from landfill leachate compared to ZrCl4 . However, too much usage of SnCl4 potentially generate secondary pollutant. Therefore, combination with O3 as pre-treatment is investigated. Combination treatment of SnCl4 ( as coagulant) with O3 had recorded the highest removal of colour (97.1%) and COD (88%). The biodegradability ratio of this sequence also improved from 0.03 to 0.28.