MyMedR

Displaying publications 21 - 40 of 139 in total

Abstract:

Sort:

Fulltext Effects of sintering time on the physical and compositional properties of porous biphasic calcium phosphate foam

Cik Rohaida, C.H., Idris, B., Rusnah, M., Mohd Reusmaazran, Y., Narimah, A.B.

Journal of Nuclear and Related Technologies, 2009;2009(1):206-216.
MyJurnal

Phase composition of calcium phosphate ceramic is a characteristic directly related to the biological response of implants due to the differences in mechanical and biochemical properties of these compounds. The biodegradation rate of biphasic calcium phosphate (BCP) can be controlled by altering the HA to β-TCP ratios. In this study the crystalline phase evolution of BCP synthesized via precipitation from aqueous solution of (NH4)2PO4 titrated into heated solution of Ca (NO3)2 was evaluated. The resulting powder was fabricated into porous scaffold using polyurethane foam method. Bulk powders were sintered from 700 - 1400°C to determine the most significant sintering temperature to obtain a stable and well crystallize BCP phases. The porous scaffolds were then sintered at selected temperature and the effects of various sintering times from 5,7,9,11,13 and 15 h were investigated. Bulk powders were characterized by dilatometer, IR analysis and XRD and porous scaffolds were analyzed by XRD and SEMEdx. RIR method was performed to show that the HA to β-TCP ratios were increased with increasing of sintering time and reached the maximum HA value at 11h. It is found that, the possibilities to manipulate the HA to β-TCP ratios in BCP porous scaffold by just controlling the sintering time of the scaffold without controlling the starting powder characteristics.

Matched MeSH terms: Ceramics
Fulltext The effect of agitation speed on the co-deposition of Ni–SiC composite coating

Nur Azam Badarulzaman, Lee, Chung Heung, Ahmad Azmin Mohamad, Zainal Arifin Ahmad, Purwadaria, Sunara

Journal of Nuclear and Related Technologies, 2007;2007(1):83-86.
MyJurnal

Ni–SiC composite coatings were electrodeposited from a Watts-type bath containing 5 g/l SiC particles in suspension. The particles were dispersed with the aid of mechanical agitation at 75 rpm and 150 rpm. EDX analysis confirmed the existence of Ni and SiC in the coatings. The effects of agitation speed on hardness properties of the coatings were investigated. SEM results showed that lower agitation speed could improve the amount of co-deposited SiC particles and increase the hardness of the composite coatings. The bonding between the Ni metal matrix and the SiC ceramic particles was compact.

Matched MeSH terms: Ceramics
Fulltext Cement-boron carbide concrete as radiation shielding material

Yusof Abdullah, Mohd Reusmaazran Yusof, Azali Muhamad, Zaifol Samsu, Nurhaslinda Ee Abdullah

Journal of Nuclear and Related Technologies, 2010;2010(2):74-79.
MyJurnal

Boron carbide (B4C) is a ceramic material which is effective to absorb thermal neutron due to wide neutron absorption cross section. In this work, B4C is added into concrete as fine aggregates to test the attenuation properties by getting the attenuation coefficient of the concrete/B4C. The samples of concrete/B4C were exposing to the thermal neutron radiation source (241-Americium-Berylium) at the dos rate of 29.08 mR/h. The result show that the attenuation coefficient of the sample with 20wt% B4C is 0.299cm -1 and the sample without B4C is 0.238cm -1 and hence, concrete/B4C is suitable as a shield for thermal neutron radiation.

Matched MeSH terms: Ceramics
Fulltext Lattice constants analysis of BaXSr1-XTIO3 ceramic for x=0.3; 0.5 and 0.7 by visual basic program

Jamal, Z., Idris, M.S., Irzaman, Barmawi, M.

Journal of Nuclear and Related Technologies, 2007;2007(1):137-142.
MyJurnal

Ceramic of BaxSr1-xTiO3 (BST) for x =0.3; 0.5 and 0.7 were successfully deposited by solid solution method. The BST ceramic were analyzed by x-ray diffraction (XRD). The XRD spectra was recorded on a Philips type PW 3701 diffractometer using CuKD (Oco = 1.54056 Å) radiation at 30 KV and 30 mA (900 watt). The spectra shows that BST ceramic are polycrystalline with tetragonal structure. The lattice constants analysis of the grown ceramics was analyzed by visual basic program. Using Cohen’s and Cramer’s algorithms in visual basic program, , the lattice constants are a = b = 3.877 Å; c = 3.970 Å for Ba0.3Sr0.7TiO3 ceramic, a = b = 3.979 Å; c = 3.981 Å. for Ba0.5Sr0.5TiO3 ceramic and a = b = 3.965 Å; c = 4.005 Å for Ba0.7Sr0.3TiO3 ceramic, respectively. The reform value of the lattice constant of BST ceramic is possibly associated with the anti site defects of Ba and Sr.

Matched MeSH terms: Ceramics
Fulltext The effects of CR2O3 addition on microstructure and fracture toughness of ZTA ceramic composite

Ahmad Zahirani Ahmad Azhar, Hasmaliza Mohamed, Mani Maran Ratnam, Zainal Arifin Ahmad

Journal of Nuclear and Related Technologies, 2013;2013(2):9-15.
MyJurnal

The microstructure and mechanical properties of ceramic composites produced from alumina, yttria stabilized zirconia and chromia oxide system was investigated. The Cr2O3 weight percent was varied from 0 wt% to 1.0 wt%. Each batch of composition was mixed, uniaxially pressed to 13mm diameter and sintered at 1600 ◦C for 4 h in pressureless conditions. Studies on the effects of the sample microstructures on their mechanical and physical properties such as fracture toughness and bulk density were carried out. Results show that an addition of 0.6 wt% of Cr2O3 produces the best mechanical properties. Furthermore, microstructural observations show that the Al2O3 grain size is significantly dependent on the amount of Cr2O3 additives used. Maximum value obtained with 0.6 wt % Cr2O3 for the fracture toughness is 5.36 MPa.m1/2.

Matched MeSH terms: Ceramics
Fulltext Polishing Mechanism And Its Effect On The Mechanical Properties Of Ceramic Restorations - A Review Of The Literature

Ahmad, R., Wu, B.W., Morgano, S.M.

Ann Dent, 2001;8(1):-.
MyJurnal

Polishing of dental ceramics has become an increasingly important procedure in restorative dentistry as allceramic restorations, which require post-cementation occlusal adjustment, are gaining in popularity. There are numerous studies in both dental and ceramic literature on polishing of dental ceramics and the effects of polishing on their mechanical properties. However, lack of standardization in polishing parameters, precludes comparison among these studies. A clear understanding is lacking of the relative roles and interdependence of handpiece speed, abrasive characteristic, and polishing load. This paper will discuss the mechanism of polishing and review the literature on polishing and its effect on the mechanical properties of ceramic restorations.

Matched MeSH terms: Ceramics
Fulltext Research trend in the processing and application of macroporous ceramic components

Dele-Afolabi, Temitope T., Azmah M.A. Hanim, Norkhairunnisa Mazlan, Shafreeza Sobri, Calin, Recep

The Pertanika Journal of Scholarly Research Reviews, 2017;3(3):83-92.
MyJurnal

Porous ceramic components with decently controlled porosity offers remarkable advantages in industrial and structural applications such as fluid filtration, thermal insulation and scaffolds for bone tissue engineering. In this review study of porous ceramic components, requisite processing techniques necessary for the development of porous ceramics with imbued microstructural model intended for a specific application. An appraisal of the fabrication was made with respect to their economic viability wherein cost effective methods having great potentials in decently controlling the pore network imbued within the host ceramic matrix was preferred over the capital intensive counterparts.

Matched MeSH terms: Ceramics
Fulltext A Near-Zero Refractive Index Meta-Surface Structure for Antenna Performance Improvement

Ullah MH, Islam MT, Faruque MRI

Materials (Basel), 2013 Nov 06;6(11):5058-5068.
PMID: 28788376 DOI: 10.3390/ma6115058

A new meta-surface structure (MSS) with a near-zero refractive index (NZRI) is proposed to enhance the performance of a square loop antenna array. The main challenge to improve the antenna performance is increment of the overall antenna volume that is mitigated by assimilating the planar NZRI MSS at the back of the antenna structure. The proposed NZRI MSS-loaded CPW-fed (Co-Planar Waveguide) four-element array antenna is designed on ceramic-bioplastic-ceramic sandwich substrate using high-frequency structure simulator (HFSS), a finite-element-method-based simulation tool. The gain and directivity of the antenna are significantly enhanced by incorporating the NZRI MSS with a 7 × 6 set of elements at the back of the antenna structure. Measurement results show that the maximum gains of the antenna increased from 6.21 dBi to 8.25 dBi, from 6.52 dBi to 9.05 dBi and from 10.54 dBi to 12.15 dBi in the first, second and third bands, respectively. The effect of the slot configuration in the ground plane on the reflection coefficient of the antenna was analyzed and optimized. The overall performance makes the proposed antenna appropriate for UHFFM (Ultra High Frequency Frequency Modulation) telemetry-based space applications as well as mobile satellite, microwave radiometry and radio astronomy applications.

Matched MeSH terms: Ceramics
Fulltext Design and Development for Capacitive Humidity Sensor Applications of Lead-Free Ca,Mg,Fe,Ti-Oxides-Based Electro-Ceramics with Improved Sensing Properties via Physisorption

Tripathy A, Pramanik S, Manna A, Bhuyan S, Azrin Shah NF, Radzi Z, et al.

Sensors (Basel), 2016 Jul 21;16(7).
PMID: 27455263 DOI: 10.3390/s16071135

Despite the many attractive potential uses of ceramic materials as humidity sensors, some unavoidable drawbacks, including toxicity, poor biocompatibility, long response and recovery times, low sensitivity and high hysteresis have stymied the use of these materials in advanced applications. Therefore, in present investigation, we developed a capacitive humidity sensor using lead-free Ca,Mg,Fe,Ti-Oxide (CMFTO)-based electro-ceramics with perovskite structures synthesized by solid-state step-sintering. This technique helps maintain the submicron size porous morphology of the developed lead-free CMFTO electro-ceramics while providing enhanced water physisorption behaviour. In comparison with conventional capacitive humidity sensors, the presented CMFTO-based humidity sensor shows a high sensitivity of up to 3000% compared to other materials, even at lower signal frequency. The best also shows a rapid response (14.5 s) and recovery (34.27 s), and very low hysteresis (3.2%) in a 33%-95% relative humidity range which are much lower values than those of existing conventional sensors. Therefore, CMFTO nano-electro-ceramics appear to be very promising materials for fabricating high-performance capacitive humidity sensors.

Matched MeSH terms: Ceramics
Intelligent optimization for modelling superhydrophobic ceramic membrane oil flux and oil-water separation efficiency: Evidence from wastewater treatment and experimental laboratory

Usman J, Salami BA, Gbadamosi A, Adamu H, Usman AG, Benaafi M, et al.

Chemosphere, 2023 Aug;331:138726.
PMID: 37116721 DOI: 10.1016/j.chemosphere.2023.138726

Due to the significant energy and economic losses brought on by the global oil spill, there has been an increased interest in oil-water separation. This study presents strong non-linear machine learning models (support vector regression (SVR) and Gaussian process regression (GPR)) with the Response surface method (RSM) to predict the oil flux and oil-water separation efficiency of wastewater using ceramic membrane technology. For the model development and prediction of oil flux (OF) and oil-water separation efficiency (OSE), oil concentration (mg/L), feed flow rate (mL/min), and pH were considered as input variables. The input variables are combined in three combinations to study the most contributing input features to the models' performance. Mean square error (MSE) and Nash-Sutcliffe coefficient efficiency (NSE) were used to assess the prediction performances of the developed models with the different number of input combinations considered in the study. For the two target variables (OF and OSE), GPR and SVR models were used to separately predict them. For OF, the SVR-2 [Combo-2] model (MSE = 0.9255 and NSE = 2.7976) performed better with higher prediction accuracy compared to GPR-2 [Combo-2] model (MSE = 0.763 and NSE = 6.437). In addition, for OSE, the GPR-3 [Combo-3] model (MSE = 0.995 and NSE = 0.5544) performed slightly better than SVR-3 [Combo-3] model (MSE = 0.992 and NSE = 0.8066). The results showed that the SVR model with the combo-2 and GPR-3 models for OF and OSE variables are the proposed models with the best performance and accuracy. This machine learning study will aid in better evaluating the function of materials such as ceramic in membrane performance features such as oil flux and rejection prediction, separation efficiency, water recovery, membrane fouling, and so on. As for academics and manufacturers, this machine learning (ML) strategy will boost performance and allow a better understanding of system governance.

Matched MeSH terms: Ceramics
Fulltext Investigation of Embedded Si/C System Exposed to a Hybrid Reaction of Centrifugal-Assisted Thermite Method

Mahmoodian R, Yahya R, Dabbagh A, Hamdi M, Hassan MA

PLoS One, 2015;10(12):e0144632.
PMID: 26641651 DOI: 10.1371/journal.pone.0144632

A novel method is proposed to study the behavior and phase formation of a Si+C compacted pellet under centrifugal acceleration in a hybrid reaction. Si+C as elemental mixture in the form of a pellet is embedded in a centrifugal tube. The pellet assembly and tube are exposed to the sudden thermal energy of a thermite reaction resulted in a hybrid reaction. The hybrid reaction of thermite and Si+C produced unique phases. X-ray diffraction pattern (XRD) as well as microstructural and elemental analyses are then investigated. XRD pattern showed formation of materials with possible electronic and magnetic properties. The cooling rate and the molten particle viscosity mathematical model of the process are meant to assist in understanding the physical and chemical phenomena took place during and after reaction. The results analysis revealed that up to 85% of materials converted into secondary products as ceramics-matrix composite.

Matched MeSH terms: Ceramics/chemistry*
Fulltext Photopyroelectric spectroscopic studies of ZnO-MnO(2)-Co(3)O(4)-V(2)O(5) ceramics

Rizwan Z, Zakaria A, Ghazali MS

Int J Mol Sci, 2011;12(3):1625-32.
PMID: 21673911 DOI: 10.3390/ijms12031625

Photopyroelectric (PPE) spectroscopy is a nondestructive tool that is used to study the optical properties of the ceramics (ZnO + 0.4MnO(2) + 0.4Co(3)O(4) + xV(2)O(5)), x = 0-1 mol%. Wavelength of incident light, modulated at 10 Hz, was in the range of 300-800 nm. PPE spectrum with reference to the doping level and sintering temperature is discussed. Optical energy band-gap (E(g)) was 2.11 eV for 0.3 mol% V(2)O(5) at a sintering temperature of 1025 °C as determined from the plot (ρhυ)(2)versushυ. With a further increase in V(2)O(5), the value of E(g) was found to be 2.59 eV. Steepness factor 'σ(A)' and 'σ(B)', which characterize the slope of exponential optical absorption, is discussed with reference to the variation of E(g). XRD, SEM and EDAX are also used for characterization of the ceramic. For this ceramic, the maximum relative density and grain size was observed to be 91.8% and 9.5 μm, respectively.

Matched MeSH terms: Ceramics/chemistry*
Fulltext Use of a reflectance spectroscopy accessory for optical characterization of ZnO-Bi(2)O(3)-TiO(2) ceramics

Ghazali MS, Zakaria A, Rizwan Z, Kamari HM, Hashim M, Zaid MH, et al.

Int J Mol Sci, 2011;12(3):1496-504.
PMID: 21673903 DOI: 10.3390/ijms12031496

The optical band-gap energy (E(g)) is an important feature of semiconductors which determines their applications in optoelectronics. Therefore, it is necessary to investigate the electronic states of ceramic ZnO and the effect of doped impurities under different processing conditions. E(g) of the ceramic ZnO + xBi(2)O(3) + xTiO(2), where x = 0.5 mol%, was determined using a UV-Vis spectrophotometer attached to a Reflectance Spectroscopy Accessory for powdered samples. The samples was prepared using the solid-state route and sintered at temperatures from 1140 to 1260 °C for 45 and 90 minutes. E(g) was observed to decrease with an increase of sintering temperature. XRD analysis indicated hexagonal ZnO and few small peaks of intergranular layers of secondary phases. The relative density of the sintered ceramics decreased and the average grain size increased with the increase of sintering temperature.

Matched MeSH terms: Ceramics/chemistry*
Biaxial flexural strength of Turkom-Cera core compared to two other all-ceramic systems

Al-Makramani BM, Razak AA, Abu-Hassan MI

J Appl Oral Sci, 2010 Dec;18(6):607-12.
PMID: 21308292

Advances in all-ceramic systems have established predictable means of providing metal-free aesthetic and biocompatible materials. These materials must have sufficient strength to be a practical treatment alternative for the fabrication of crowns and fixed partial dentures.
OBJECTIVES: The aim of this study was to compare the biaxial flexural strength of three core ceramic materials.
MATERIAL AND METHODS: Three groups of 10 disc-shaped specimens (16 mm diameter x 1.2 mm thickness - in accordance with ISO-6872, 1995) were made from the following ceramic materials: Turkom-Cera Fused Alumina [(Turkom-Ceramic (M) Sdn Bhd, Puchong, Selangor, Malaysia)], In-Ceram (Vita Zahnfabrik, Bad Säckingen, Baden-Württemberg, Germany) and Vitadur-N (Vita Zahnfabrik, Bad Säckingen, Baden-Württemberg, Germany), which were sintered according to the manufacturer's recommendations. The specimens were subjected to biaxial flexural strength test in an universal testing machine at a crosshead speed of 0.5 mm/min. The definitive fracture load was recorded for each specimen and the biaxial flexural strength was calculated from an equation in accordance with ISO-6872.
RESULTS: The mean biaxial flexural strength values were: Turkom-Cera: 506.8 ± 87.01 MPa, In-Ceram: 347.4 ± 28.83 MPa and Vitadur-N: 128.7 ± 12.72 MPa. The results were analyzed by the Levene's test and Dunnett's T3 post-hoc test (SPSS software V11.5.0 for Windows, SPSS, Chicago, IL, USA ) at a preset significance level of 5% because of unequal group variances (P<0.001). There was statistically significant difference between the three core ceramics (P<0.05). Turkom-Cera showed the highest biaxial flexural strength, followed by In-Ceram and Vitadur-N.
CONCLUSIONS: Turkom-Cera core had significantly higher flexural strength than In-Ceram and Vitadur-N ceramic core materials.

Matched MeSH terms: Ceramics/chemistry*
Effect of sintering temperature on the properties of modified mechanical alloyed CaCu3Ti4O12

Hutagalung SD, Ying OL, Ahmad ZA

IEEE Trans Ultrason Ferroelectr Freq Control, 2007 Dec;54(12):2587-91.
PMID: 18276560 DOI: 10.1109/TUFFC.2007.582

This paper presents the effects of calcination time and sintering temperature on the properties of CaCu(3)Ti(4)O(12). Electroceramic material of CaCu(3)Ti(4)O(12) was prepared using a modified mechanical alloying technique that covers several processes, which are preparation of raw material, mixing and ball milling for 5 hours, calcination, pellet forming and, sintering. The objective of this modified technique is to enable the calcination and sintering processes to be carried out at a shorter time and lower temperature. The x-ray diffraction (XRD) analysis result shows that a single-phase of CaCu(3)Ti(4)O(12) was completely formed by calcination at 750 degrees C for 12 hours. Meanwhile, the grain size of a sample sintered at 1050 degrees C for 24 hours is extremely large, in the range of 20-50 mum obtained from field emission scanning electron microscopy (FESEM) images. The dielectric constant value of 14,635 was obtained at 10 kHz by impedance (LCR) meter in the sintered sample at 1050 degrees C. However, the dielectric constant value of samples sintered at 900 and 950 degrees C is quite low, in the range of 52-119.

Matched MeSH terms: Ceramics/chemistry*
The influence of sintering temperature on the porosity and strength of porous hydroxyapatite ceramics

Rusnah M, Andanastuti M, Idris B

Med J Malaysia, 2004 May;59 Suppl B:158-9.
PMID: 15468866

The present paper reports on the influence of sintering temperature on the porosity and strength of porous hydroxyapatite (HA). HA powder was first prepared by the sol-gel precipitation method using calcium hydroxide and ortho-phosporic acid. The fine HA powder, measuring <50 microm was then mixed into a slurry with the addition of binder agent, being a mixture of sago and PVA. A small amount of sodium dodecyl sulphate was also used as a foaming agent. Porous HA samples were then prepared via slip casting technique. The surface morphology of the sintered samples was observed under scanning electron microscopy at 20 kV and the compositions were determined via SEM-EDX. A universal testing machine was used to determine the compaction strength of the sintered samples.

Matched MeSH terms: Ceramics/analysis*
Study on changing the coefficient of thermal expansion (CTE) of dental porcelain

Jamaluddin O, Zainal AA

Med J Malaysia, 2004 May;59 Suppl B:143-4.
PMID: 15468859

Raising the thermal expansion coefficient (CTE) of dental porcelains is important to match the CTE of the ceramic material with the higher CTE of the metal inlay in dental restorations. The higher thermal expansion of the leucite phase increases the overall thermal expansion coefficient of the dental porcelain. Potassium nitrate (KNO3) additions in controlled percentages to the base dental porcelain formulation help in the formation of a leucite phase. The percentage added was 5,10 and 20 weight percent of leucite, respectively, to the total base frit composition. The change in CTE values was then investigated using a Linseis Dilatometer. A 20wt% KNO3 addition resulted in a CTE of 9.0 microm/m-K compared to the 7.7 microm/m-K CTE of the base composition. The microstructures observed under the scanning electron microscope (SEM) show a multiphase material with the leucite phases dispersed within a glassy matrix. The results suggest that higher CTEs in the dental porcelain are possible by increasing the KNO3- additions within the limits tested.

Matched MeSH terms: Ceramics/analysis*
Fulltext Customizable Ceramic Nanocomposites Using Carbon Nanotubes

Okolo C, Rafique R, Iqbal SS, Subhani T, Saharudin MS, Bhat BR, et al.

Molecules, 2019 Sep 01;24(17).
PMID: 31480573 DOI: 10.3390/molecules24173176

A novel tweakable nanocomposite was prepared by spark plasma sintering followed by systematic oxidation of carbon nanotube (CNT) molecules to produce alumina/carbon nanotube nanocomposites with surface porosities. The mechanical properties (flexural strength and fracture toughness), surface area, and electrical conductivities were characterized and compared. The nanocomposites were extensively analyzed by field emission scanning electron microscopy (FE-SEM) for 2D qualitative surface morphological analysis. Adding CNTs in ceramic matrices and then systematically oxidizing them, without substantial reduction in densification, induces significant capability to achieve desirable/application oriented balance between mechanical, electrical, and catalytic properties of these ceramic nanocomposites. This novel strategy, upon further development, opens new level of opportunities for real-world/industrial applications of these relatively novel engineering materials.

Matched MeSH terms: Ceramics/chemistry*
Fulltext "Ormocer an innovative technology": A replacement for conventional cements and veneer? A comparative in vitro analysis

Rajeev V, Arunachalam R, Nayar S, Arunima PR, Ganapathy S, Vedam V

Eur J Dent, 2017 4 25;11(1):58-63.
PMID: 28435367 DOI: 10.4103/ejd.ejd_113_16

OBJECTIVE: This in vitro study was designed to assess shear bond strength (SBS) of ormocer flowable (OF) resin as a luting agent, ormocer as an indirect veneer material with portrayal of modes of failures using scanning electron microscope (SEM).
MATERIALS AND METHODS: Sixty maxillary central incisors were divided into Group I, II, and III with 20 samples each based on luting cement used. They were OF, self-adhesive (SA) cement, and total etch (TE) cement. These groups were subdivided into "a" and "b" of ten each based on the type of veneering materials used. Veneer discs were fabricated using Ormocer restorative (O) and pressable ceramic (C). Specimens were thermocycled and loaded under universal testing machine for SBS. The statistical analysis was done using one-way ANOVA post hoc Tukey honest significant difference method.
RESULTS: A significant difference was observed between the Groups I and II (P < 0.05). The highest mean bond strength when using ormocer veneer was obtained with the Group Ia (19.11 ± 1.92 Mpa) and lowest by Group IIa (8.1 ± 1.04 Mpa), whereas the highest mean bond strength while using ceramic veneer was of similar range for Group Ib (18.04 ± 4.08 Mpa) and Group IIIb (18.07 ± 1.40 Mpa). SEM analysis revealed OF and TE presented mixed type of failure when compared with SA where failure mode was totally adhesive.
CONCLUSION: OF was found equally efficient like TE. Bond strength of ormocer as a veneer was not inferior to ceramic making it one of the promising additions in the field of dentistry.

Matched MeSH terms: Ceramics; Organically Modified Ceramics
The impact of surface and geometry on coefficient of friction of artificial hip joints

Choudhury D, Vrbka M, Mamat AB, Stavness I, Roy CK, Mootanah R, et al.

J Mech Behav Biomed Mater, 2017 08;72:192-199.
PMID: 28500998 DOI: 10.1016/j.jmbbm.2017.05.011

Coefficient of friction (COF) tests were conducted on 28-mm and 36-mm-diameter hip joint prostheses for four different material combinations, with or without the presence of Ultra High Molecular Weight Polyethylene (UHMWPE) particles using a novel pendulum hip simulator. The effects of three micro dimpled arrays on femoral head against a polyethylene and a metallic cup were also investigated. Clearance played a vital role in the COF of ceramic on polyethylene and ceramic on ceramic artificial hip joints. Micro dimpled metallic femoral heads yielded higher COF against a polyethylene cup; however, with metal on metal prostheses the dimpled arrays significantly reduced the COF. In situ images revealed evidence that the dimple arrays enhanced film formation, which was the main mechanism that contributed to reduced friction.

Matched MeSH terms: Ceramics/analysis*

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links