The steady laminar combined convective flow with heat and mass transfer of a Newtonian viscous incompressible fluid over a permeable flat plate with linear hydrodynamic and thermal slips has been investigated numerically. The velocity of the external flow, the suction/injection velocity and the temperature of the plate surface are assumed to vary nonlinearly following the power law with the distance along the plate from the origin. Lie group analysis is used to develop the similarity transformations and the governing momentum, the energy conservation and the mass conservation equations are converted to a system of coupled nonlinear ordinary differential equations with the associated boundary conditions. The resulting equations are solved numerically using the Runge-Kutta-Fehlberg fourth-fifth order numerical method. The effects of hydrodynamic slip parameter (a), thermal slip parameter (b), suction/injection parameter (fw), power law parameter (m), buoyancy ratio parameter (N), Prandtl number (Pr) and Schmidt number (Sc) on the fluid flow, heat transfer and mass transfer characteristics are investigated and presented graphically. We have also shown the effects of the Reynolds number (Re) and the power law parameter (m) on the velocity slip and the thermal slip factors. Good agreement is found between the numerical results of the present paper and published results.
Effects of aluminium hydroxide (ATH) addition on the properties of palm-based polyurethane composites were investigated. The hybrid composites were prepared by mixing 10 wt% of oil palm empty fruit bunch fiber (EFB) with ATH at varying amount of 2, 4 and 6 wt% of the overall mass of the resin. The compression stress and modulus gave the highest values of 575 and 2301 kPa, respectively at 2 wt% loading of ATH. The compression stress and modulus decreased drastically at 4 wt% (431 kPa and 1659 kPa, respectively) and further decreased at 6 wt% ATH (339 and 1468 kPa, respectively). However, the burning rate is inversely proportional to the loading percentage where the highest burning rate was observed at 2 wt% ATH. Sound absorption analysis indicated a large absorption coefficient at high frequency (4000 Hz) for all samples. The highest absorption coefficient was obtained from PU-EFB/ATH with 4 wt% ATH.
Stillbirth is a devastating event to the parents, relatives, friends, and families. The role of anticoagulants in the prevention of unexplained stillbirths is uncertain. An open-label interventional prospective cohort study was conducted on 144 women with a history of unexplained stillbirths. The intervention group had a high umbilical artery resistance index (RI) and received bemiparin. The nonintervention group had a normal RI and did not receive any intervention. We measured the adjusted odds ratio (OR) and 95% confidence interval (CI) of the main outcome for these variables using logistic regression analysis. Fresh stillbirth and early neonatal death rates were lower (P = .005, OR = 11.949 and 95% CI = 2.099-68.014) and newborn weight was higher (P = .015, OR = 0.048, 95% CI = 0.004-0.549) in the group that received bemiparin. Bemiparin is effective in decreasing the rate of stillbirth in women with a history of previous unexplained stillbirths.
Two chitosan samples (medium molecular weight (MMCHI) and low molecular weight (LMCHI)) were investigated as an enzyme immobilization matrix for the fabrication of a glucose biosensor. Chitosan membranes prepared from acetic acid were flexible, transparent, smooth and quick-drying. The FTIR spectra showed the existence of intermolecular interactions between chitosan and glucose oxidase (GOD). Higher catalytic activities were observed on for GOD-MMCHI than GOD-LMCHI and for those crosslinked with glutaraldehyde than using the adsorption technique. Enzyme loading greater than 0.6 mg decreased the activity. Under optimum conditions (pH 6.0, 35°C and applied potential of 0.6 V) response times of 85 s and 65 s were observed for medium molecular weight chitosan glucose biosensor (GOD-MMCHI/PT) and low molecular weight chitosan glucose biosensor (GOD-LMCHI/PT), respectively. The apparent Michaelis-Menten constant ([Formula: see text]) was found to be 12.737 mM for GOD-MMCHI/PT and 17.692 mM for GOD-LMCHI/PT. This indicated that GOD-MMCHI/PT had greater affinity for the enzyme. Moreover, GOD-MMCHI/PT showed higher sensitivity (52.3666 nA/mM glucose) when compared with GOD-LMCHI/PT (9.8579 nA/mM glucose) at S/N>3. Better repeatability and reproducibility were achieved with GOD-MMCHI/PT than GOD-LMCHI/PT regarding glucose measurement. GOD-MMCHI/PT was found to give the highest enzymatic activity among the electrodes under investigation. The extent of interference encountered by GOD-MMCHI/PT and GOD-LMCHI/PT was not significantly different. Although the Nafion coated biosensor significantly reduced the signal due to the interferents under study, it also significantly reduced the response to glucose. The performance of the biosensors in the determination of glucose in rat serum was evaluated. Comparatively better accuracy and recovery results were obtained for GOD-MMCHI/PT. Hence, GOD-MMCHI/PT showed a better performance when compared with GOD-LMCHI/PT. In conclusion, chitosan membranes shave the potential to be a suitable matrix for the development of glucose biosensors.
Poly(3-hydroxybutyrate-co-3-hydroxyvalerate-co-4-hydroxybutyrate) [P(3HB-co-3HV-co-4HB)] terpolymer was produced using Cupriavidus sp. USMAA2-4 via one-step cultivation process through combination of various carbon sources such as 1,4-butanediol or γ-butyrolactone with either 1-pentanol, valeric acid, or 1-propanol. Oleic acid was added to increase the biomass production. The composition of 3HV and 4HB monomers were greatly affected by the concentration of 1,4-butanediol and 1-pentanol. Terpolymers with 3HV and 4HB molar fractions ranging from 2 to 41 mol.% and 5 to 31 mol.%, respectively, were produced by varying the concentration of carbon precursors. The thermal and mechanical properties of the terpolymers containing different proportions of the constituent monomers were characterized using gel permeation chromatography (GPC), DSC, and tensile machine. GPC analysis showed that the molecular weights (M (w)) of the terpolymer produced were within the range of 346 to 1,710 kDa. The monomer compositions of 3HV and 4HB were also found to have great influences on the thermal and mechanical properties of the terpolymer P(3HB-co-3HV-co-4HB) produced.
Natural rubber from hevea brasiliensis trees (Thailand, RRIM 600 clone) of different age (8, 20, and 35 years) were characterized by size exclusion chromatography coupled with online viscometry according to their distribution of molar mass and branching index at a temperature of 70 degrees C using cyclohexane as solvent. Washing with an aqueous solution of sodium dodecylsulfate and subsequent saponification purified the natural rubber samples. With this procedure physical branching points caused by phospholipids, proteins and hydrophobic terminal units, mainly fatty acids, of the natural rubber (cis-1,4-polyisoprene) molecule, could be removed leading to completely soluble polymer samples. All samples investigated possess a very broad (10 to 50,000 kg/mol) and distinct bimodal molar mass distribution. With increasing age the peak area in the low molar mass region decreases favoring the peak area in the high molar mass region. By plotting the branching index as a function of the both, the molar mass and the age of the trees.
Pseudomonas putida Bet001 and Delftia tsuruhatensis Bet002, isolated from palm oil mill effluent, accumulated poly(3-hydroxyalkanoates) (PHAs) when grown on aliphatic fatty acids, sugars, and glycerol. The substrates were supplied at 20:1 C/N mole ratio. Among C-even n-alkanoic acids, myristic acid gave the highest PHA content 26 and 28 wt% in P. putida and D. tsuruhatensis, respectively. Among C-odd n-alkanoic acids, undecanoic gave the highest PHA content at 40 wt% in P. putida and 46 wt% in D. tsuruhatensis on pentadecanoic acid. Sugar and glycerol gave <10 wt% of PHA content for both bacteria. Interestingly, D. tsuruhatensis accumulated both short- and medium-chain length PHA when supplied with n-alkanoic acids ranging from octanoic to lauric, sucrose, and glycerol with 3-hydroxybutyrate as the major monomer unit. In P. putida, the major hydroxyalkanoates unit was 3-hydroxyoctanoate and 3-hydroxydecanoate when grown on C-even acids. Conversely, 3-hydroxyheptanoate, 3-hydrxoynonanoate, and 3-hydroxyundecanoate were accumulated with C-odd acids. Weight-averaged molecular weight (Mw ) was in the range of 53-81 kDa and 107-415 kDa for P. putida and D. tsuruhatensis, respectively. Calorimetric analyses indicated that both bacteria synthesized semicrystalline polymer with good thermal stability with degradation temperature (Td ) ranging from 178 to 282 °C.
Purification of cyclodextrin glycosyl transferase (CGTase) from Bacillus cereus using polyethylene glycol (PEG)-potassium phosphates aqueous two-phase flotation (ATPF) system was studied in this paper. The effects of varying PEG molecular weight, tie-line length (TLL) value, volume ratio (VR), pH value, crude concentration and gas nitrogen flotation time were investigated. The optimal condition for purification of CGTase was attained at 18.0% (w/w) PEG 8000, 7.0% (w/w) potassium phosphates, VR of 3.0, 20% (w/w) crude load at pH 7, and 80 min nitrogen flotation time at a flow rate of 5 L/min. With this optimal condition, purification factor (PFT) of 21.8 and a yield (YT) of 97.1% were attained. CGTase was successfully purified in a single downstream processing step using the ATPF.
High-energy electron (2.0 MV) and gamma irradiation (60Co) has been used to modify polymeric silicone fluids of initial viscosities in the range, 90-700 cSt. Doses of electron and gamma radiation were delivered at rates of 0.246 kGy s(-1) and 15 kGy h(-1), respectively, exposure times being adjusted to ensure energy deposition in the range 30-360 kGy. Measurements were made using a differential viscometer based on a Bose Institute design. In line with expectation, samples of greater initial molecular weight (and hence greater viscosity), were observed to be more susceptible to radiation induced cross-linking than those of lower molecular weight. The role of dose rate and oxygen diffusion in determining the extent of change is discussed.
Rectus sheath hematoma (RSH) is a rare clinical entity that has been associated with the use of injectable anticoagulant therapy. Although low molecular weight heparin (LMWH) was proven to have a better safety profile than its predecessor, it is not without its own risk of bleeding. The increase in use of self-injectable LMWH in both in-patient as well as out-patient basis warrants greater awareness among health care providers, patients and caregivers regarding the potential risks and identification of possible complications. We present a fatal case of rectus sheath hematoma in an elderly man that occurred following erroneous technique of Dalteparin injection.
A search for supersymmetry is presented based on events with at least one photon, jets, and large missing transverse momentum produced in proton-proton collisions at a center-of-mass energy of 13
Te
. The data correspond to an integrated luminosity of 35.9
fb
- 1
and were recorded at the LHC with the CMS detector in 2016. The analysis characterizes signal-like events by categorizing the data into various signal regions based on the number of jets, the number of b -tagged jets, and the missing transverse momentum. No significant excess of events is observed with respect to the expectations from standard model processes. Limits are placed on the gluino and top squark pair production cross sections using several simplified models of supersymmetric particle production with gauge-mediated supersymmetry breaking. Depending on the model and the mass of the next-to-lightest supersymmetric particle, the production of gluinos with masses as large as 2120
Ge
and the production of top squarks with masses as large as 1230
Bioactive edible swiftlet's nest (ESN) sialylated-mucin (SiaMuc) hydrolysate is produced by alcalase hydrolysis. Enzymatic hydrolysis of ESN breakdown high-valued ESN SiaMuc-glycoprotein into bioactive SiaMuc-glycopeptide. This is a breakthrough for the issue of insolubility and low extraction rate in ESN, and even increases the bioavailability of ESN nutritional functionality and health benefits. Hydrolysis of ESN SiaMuc-glycoprotein was performed for 1 to 4 h and its effect on physicochemical properties, molecular weight (MW) distribution, SiaMuc-glycoprotein and glycopeptide integrity were determined. Other than improvement in solubility and bioavailability as SiaMuc-glycopeptide, results from SDS-PAGE revealed that MW of SiaMuc-glycoprotein decreased from 42.0-148.8 kDa to 17.7-142.7 kDa with increasing hydrolysis period. Further hydrolysis from maximized DH (90 min) showed an insignificant effect on the MW of ESN SiaMuc-glycopeptide and remained constant at 15.2 kDa. This highlights that enzymatic hydrolysis only influences macro SiaMuc-glycoprotein fractions (142.7, 115.3 and 102.7 kDa), while the majority of SiaMuc-glycopeptide fractions from 36.6-98.6 kDa remained intact. Conclusively, alcalase hydrolysis of ESN showed high recovery in the form of bioactive ESN SiaMuc-glycopeptide. Therefore, enzymatic biotechnology is an economic alternative applicable on ESN that broaden industrial utilization by reducing the MW without destroying the quality of bioactive SiaMuc-glycoprotein.
Introduction: Collagen and gelatin are essential protein in vertebrates and extensively used in various industries. Methods: In this study, acid-solubilized collagen and gelatin were extracted from the scales of three different species of freshwater fish namely Kelah (Tombroides), Tilapia (Oreochromis niloticus) and Snakehead fish (Channidae) and then further quantified using Bradford assay and separated by molecular weight using SDS-PAGE. Results: The extracted collagen in Tilapia fish scale was found to be the highest with 0.018 of protein absorbance among the other three fish; Kelah fish (0.017) and Snakehead fish (0.011). For gelatin, Snakehead fish scales showed the highest amount of total protein concentration followed by Tilapia and Kelah fish with 0.467, 0.144 and 0.037 μg/μL per g, respectively. Based on the SDS-PAGE results, collagen from all the three freshwater fishes were identified as a type 1 (molecular weight approximately from 95 to 130 kDa) collagen. As for gelatin, only gelatin from Snakehead fish scale was identified to be a type 1(molecular weight approximately from 95 to 130 kDa) while the other two freshwater fishes showed no clear band due to high viscosity of the gelatin produced. Conclusion: It can be said that the fishes investigated in this study have a potential to be the alternative source of collagen and gelatin.
Carboxymethyl starch (CMS) was produced from sago starch via carboxymethylation. The CMS with different degree of substitution (DS) ranges from 0.4 to 0.8 were mixed with polyethylene glycol (PEG) of different molecular weight and distilled water and the hydrogel was cured by electron beam irradiation with doses ranging from 25 to 35 kGy. The results revealed that CMS-PEG hydrogels with DS 0.4 give the optimum gel content when radiated at 30 kGy and with PEG 600. Thermogravimetric analysis (TGA) revealed that there are two phases exist in CMS with DS 0.4 in contrast to the three steps decomposition occurs in DS 0.6 and 0.8. It shows that the CMS with DS 0.4 is more thermally stable. Surface morphology revealed crosslinking among the blends when subjected into the radiation dose. The study shows both radiation and PEG addition improved most of the properties of CMS irrespective of the DS value.
Lactobacillus bulgaricus is a LAB strain which is capable of producing bacteriocin substances to inhibit Staphylococcus aureus. The aim of this study was to purify a bacteriocin-like inhibitory substance (BLIS) produced by L. bulgaricus FTDC 1211 using an aqueous impregnated resins system consisting of polyethylene-glycol (PEG) impregnated on Amberlite XAD4. Important parameters influencing on purification of BLIS, such as the molecular weight and concentration of PEG, the concentration and pH of sodium citrate and the concentration of sodium chloride, were optimized using a response surface methodology. Under optimum conditions of 11% (w/w) of PEG 4000 impregnated Amberlite XAD4 resins and 2% (w/w) of sodium citrate at pH 6, the maximum purification factor (3.26) and recovery yield (82.69% ± 0.06) were obtained. These results demonstrate that AIRS could be used as an alternate purification system in the primary recovery step.
Host induced control of pathogens involves, but not limited to, withholding of essential transition metals as well as releasing the metals at a toxic level. Zinc is one of these transition elements that plays critical role in controlling the pathogens in that manner – a key mediator in nutritional immunity. A number of subcellular and molecular mecha-nisms such as transport and storage proteins are known to maintain Zn homeostasis and scuffle with the pathogens. Pathogenic bacteria also use a number of mechanisms to combat the scuffle and fight for the right amount of Zn for their survival and growth. From the host perspective, a “delicate” balance of Zn must be maintained for immune surveillance while making the level of Zn either to starve or to intoxicate the pathogens. Metallothionein (MT), a group of low molecular weight proteins, is well known for its Zn transport and storage ability and is expected to play an important role in that nutritional immunity. Zn homeostasis by MT to fight oral pathogens is not unexpected too. Periodontitis and dental caries are two most common oral diseases which are linked to the pathogenic carnival of opportunistic bacteria. Can those culprits be exterminated through nutritional immunity using MT? Or could it be - those human hosts who become the easy prey of those pathogens lack inducible expression of MT in their oral tissues? The synthesis or degradation of MT in response to invading pathogens in oral tissues, the human-MT medi-ated Zn homeostasis in response to infectious insult in oral tissues are evident. Nonetheless, the cross talk between MT and Zn in oral nutritional immunity is largely unknown.
Natural rubber is one of the most important renewable biopolymers used in many applications due to its special properties that cannot be easily mimicked by synthetic polymers. To sustain the existence of natural rubber in industries, modifications have been made to its chemical structure from time to time in order to obtain new properties and to enable it to be employed in new applications. The chemical structure of natural rubber can be modified by exposure to ultraviolet light to reduce its molecular weight. Under controlled conditions, the natural rubber chains will be broken by photodegradation to yield low-molecular-weight natural rubber. The aim of this work was to obtain what is known as liquid natural rubber via photodegradation, with titanium dioxide nanocrystals as the catalyst. Titanium dioxide, which was firstly synthesized using the sol⁻gel method, was confirmed to be in the form of an anatase, with a size of about 10 nm. In this work, the photodegradation was carried out in latex state and yielded low-molecular-weight natural rubber latex of less than 10,000 g/mol. The presence of hydroxyl and carbonyl groups on the liquid natural rubber (LNR) chains was observed, resulting from the breaking of the chains. Scanning electron microscopy of the NR latex particles showed that titanium dioxide nanocrystals were embedded on the latex surface, but then detached during the degradation reaction.
Non-isocyanate polyurethane (NIPU) was prepared from Jatropha curcas oil (JCO) and its alkyd resin via curing with different diamines. The isocyanate-free approach is a green chemistry route, wherein carbon dioxide conversion plays a major role in NIPU preparation. Catalytic carbon dioxide fixation can be achieved through carbonation of epoxidized derivatives of JCO. In this study, 1,3-diaminopropane (DM) and isophorone diamine (IPDA) were used as curing agents separately. Cyclic carbonate conversion was catalyzed by tetrabutylammonium bromide. After epoxy conversion, carbonated JCO (CJCO) and carbonated alkyd resin (CC-AR) with carbonate contents of 24.9 and 20.2 wt %, respectively, were obtained. The molecular weight of CJCO and CC-AR were determined by gel permeation chromatography. JCO carbonates were cured with different amine contents. CJCO was blended with different weight ratios of CC-AR to improve its characteristics. The cured NIPU film was characterized by spectroscopic techniques, differential scanning calorimetry, and a universal testing machine. Field emission scanning electron microscopy was used to analyze the morphology of the NIPU film before and after solvent treatment. The solvent effects on the NIPU film interfacial surface were investigated with water, 30% ethanol, methyl ethyl ketone, 10% HCl, 10% NaCl, and 5% NaOH. NIPU based on CCJO and CC-AR (ratio of 1:3) with IPDA crosslink exhibits high glass transition temperature (44 °C), better solvent and chemical resistance, and Young's modulus (680 MPa) compared with the blend crosslinked with DM. Thus, this study showed that the presence of CC-AR in CJCO-based NIPU can improve the thermomechanical and chemical resistance performance of the NIPU film via a green technology approach.
Microencapsulation of polysaccharidic nanoparticles is met with nanoscale and biological performance changes. This study designs soft agglomerates as nanoparticle vehicle without nanoparticles undergoing physical processes that alter their geometry. The nanoparticles were made of high molecular weight chitosan/pectin with covalent 5-fluorouracil/folate. Nanoparticle aggregation vehicle was prepared from low molecular weight chitosan. The nanoparticles and aggregation vehicle were blended in specific weight ratios to produce soft agglomerates. Nanoparticles alone are unable to agglomerate. Adding aggregation vehicle (< 2 μm) promoted soft agglomeration with nanoparticles deposited onto its surfaces with minimal binary coalescence. The large and rough-surfaced aggregation vehicle promoted nanoparticles deposition and agglomeration. A rounder vehicle allowed assembly of nanoparticles-on-aggregation vehicle into agglomerates through interspersing smaller between larger populations. Soft agglomeration reduced early drug release, and was responsive to intracapsular sodium alginate coat to further sustain drug release. The soft agglomerates can serve as a primary oral colon-specific vehicle.
Membrane distillation (MD) frequently deals with membrane biofouling caused by deposition of algal organic matter (AOM) from algal blooms, hampering the treatment efficiency. In this study, AOMs, which are soluble extracellular polymeric substance (sEPS), bounded EPS (bEPS), and internal organic matter (IOM) from three benthic species (Amphora coffeaeformis, Cylindrotheca fusiformis, and Navicula incerta) were exposed to a temperature range to resemble the MD process. Results showed that EPS had higher polysaccharide fraction than protein with 85.71%, 68.26%, and 71.91% for A. coffeaeformis, N. incerta, and C. fusiformis, respectively. Both the EPS polysaccharide and protein concentration linearly increase with temperature, but the opposite was true for IOM and high-molecular-weight (HMW) polysaccharide. At 80°C, 5812.94 μg/g out of 6304.28 μg/g polysaccharide in A. coffeaeformis was of low molecular weight (LMW); hence, these findings suggested that they were the major foulants to clog the narrow pores within virgin hydrophobic membrane, forming a conditioning layer followed by deposition of HMW and hydrophilic polysaccharides onto the macropores to cause irreversible fouling. Cell lysis occurring at higher temperature increases the total protein content about 25% within the EPS matrix, inducing membrane plugging via hydrophobic-hydrophobic interactions. Overall, the AOM composition at different temperatures will likely dictate the fouling severity in MD. PRACTITIONER POINTS: EPS production of three benthic diatoms was the highest at 80°C. EPS from diatoms consists of at least 75.29% of polysaccharides. Small molecular weight carbohydrates (<12 kDa) were potential foulants. Proteins of internal organic matter (>56%) give irreversible attachment towards membranes. A. coffeaeformis was considered as the most fouling diatoms with highest EPS amount of 6304.28 μg/g.