Displaying publications 21 - 40 of 191 in total

Abstract:
Sort:
  1. Lee XJ, Lee LY, Foo LP, Tan KW, Hassell DG
    J Environ Sci (China), 2012;24(9):1559-68.
    PMID: 23520862
    The present work covers the preparation of carbon-based nanosorbents by ethylene decomposition on stainless steel mesh without the use of external catalyst for the treatment of water containing nickel ions (Ni2+). The reaction temperature was varied from 650 to 850 degrees C, while reaction time and ethylene to nitrogen flow ratio were maintained at 30 min and 1:1 cm3/min, respectively. Results show that nanosorbents synthesised at a reaction temperature of 650 degrees C had the smallest average diameter (75 nm), largest BET surface area (68.95 m2/g) and least amount of impurity (0.98 wt.% Fe). A series of batch-sorption tests were performed to evaluate the effects of initial pH, initial metal concentration and contact time on Ni2+ removal by the nanosorbents. The equilibrium data fitted well to Freundlich isotherm. The kinetic data were best correlated to a pseudo second-order model indicating that the process was of chemisorption type. Further analysis by the Boyd kinetic model revealed that boundary layer diffusion was the controlling step. This primary study suggests that the prepared material with Freundlich constants compared well with those in the literature, is a promising sorbent for the sequestration of Ni2+ in aqueous solutions.
    Matched MeSH terms: Nanotubes, Carbon/chemistry*
  2. Kabbashi NA, Atieh MA, Al-Mamun A, Mirghami ME, Alam MD, Yahya N
    J Environ Sci (China), 2009;21(4):539-44.
    PMID: 19634432
    The capability of carbon nanotubes (CNTs) to adsorb lead (Pb) in aqueous solution was investigated. Batch mode adsorption experiment was conducted to determine the effects of pH, agitation speed, CNTs dosage and contact time. The removal of Pb(II) reached maximum value 85% or 83% at pH 5 or 40 mg/L of CNTs, respectively. Higher correlation coefficients from Langmuir isotherm model indicates the strong adsorptions of Pb(II) on the surface of CNTs (adsorption capacity Xm = 102.04 mg/g). The results indicates that the highest percentage removal of Pb (96.03%) can be achieved at pH 5, 40 mg/L of CNTs, contact time 80 min, and agitation speed 50 r/min.
    Matched MeSH terms: Nanotubes, Carbon*
  3. Bahrami A, Talib ZA, Yunus WM, Behzad K, M Abdi M, Din FU
    Int J Mol Sci, 2012;13(11):14917-28.
    PMID: 23203102 DOI: 10.3390/ijms131114917
    Polypyrrole (PPy) and polypyrrole-carboxylic functionalized multi wall carbon nanotube composites (PPy/f-MWCNT) were synthesized by in situ chemical oxidative polymerization of pyrrole on the carbon nanotubes (CNTs). The structure of the resulting complex nanotubes was characterized by transmission electron microscopy (TEM) and X-ray diffraction (XRD). The effects of f-MWCNT concentration on the electrical properties of the resulting composites were studied at temperatures between 100 K and 300 K. The Hall mobility and Hall coefficient of PPy and PPy/f-MWCNT composite samples with different concentrations of f-MWCNT were measured using the van der Pauw technique. The mobility decreased slightly with increasing temperature, while the conductivity was dominated by the gradually increasing carrier density.
    Matched MeSH terms: Nanotubes, Carbon/chemistry*
  4. John AA, Subramanian AP, Vellayappan MV, Balaji A, Mohandas H, Jaganathan SK
    Int J Nanomedicine, 2015;10:4267-77.
    PMID: 26170663 DOI: 10.2147/IJN.S83777
    Neuroregeneration is the regrowth or repair of nervous tissues, cells, or cell products involved in neurodegeneration and inflammatory diseases of the nervous system like Alzheimer's disease and Parkinson's disease. Nowadays, application of nanotechnology is commonly used in developing nanomedicines to advance pharmacokinetics and drug delivery exclusively for central nervous system pathologies. In addition, nanomedical advances are leading to therapies that disrupt disarranged protein aggregation in the central nervous system, deliver functional neuroprotective growth factors, and change the oxidative stress and excitotoxicity of affected neural tissues to regenerate the damaged neurons. Carbon nanotubes and graphene are allotropes of carbon that have been exploited by researchers because of their excellent physical properties and their ability to interface with neurons and neuronal circuits. This review describes the role of carbon nanotubes and graphene in neuroregeneration. In the future, it is hoped that the benefits of nanotechnologies will outweigh their risks, and that the next decade will present huge scope for developing and delivering technologies in the field of neuroscience.
    Matched MeSH terms: Nanotubes, Carbon*
  5. Pahlevanzadeh F, Bakhsheshi-Rad HR, Kharaziha M, Kasiri-Asgarani M, Omidi M, Razzaghi M, et al.
    J Mech Behav Biomed Mater, 2021 04;116:104320.
    PMID: 33571842 DOI: 10.1016/j.jmbbm.2021.104320
    Polymethyl methacrylate (PMMA) bone cements (BCs) have some drawbacks, including limited bioactivity and bone formation, as well as inferior mechanical properties, which may result in failure of the BC. To deal with the mentioned issues, novel bioactive polymethyl methacrylate-hardystonite (PMMA-HT) bone cement (BC) reinforced with 0.25 and 0.5 wt% of carbon nanotube (CNT) and reduced graphene oxide (rGO) was synthesized. In this context, the obtained bone cements were evaluated in terms of their mechanical and biological characteristics. The rGO reinforced bone cement exhibited better mechanical properties to the extent that the addition of 0.5 wt% of rGO where its compressive and tensile strength of bioactive PMMA-HT/rGO cement escalated from 92.07 ± 0.72 MPa, and 40.02 ± 0.71 MPa to 187.48 ± 5.79 MPa and 64.92 ± 0.75 MPa, respectively. Besides, the mechanisms of toughening, apatite formation, and cell interaction in CNT and rGO encapsulated PMMA have been studied. Results showed that the existence of CNT and rGO in BCs led to increase of MG63 osteoblast viability, and proliferation. However, rGO reinforced bone cement was more successful in supporting MG63 cell attachment compared to the CNT counterpart due to its wrinkled surface, which made a suitable substrate for cell adhesion. Based on the results, PMMA-HT/rGO can be a proper bone cement for the fixation of load-bearing implants.
    Matched MeSH terms: Nanotubes, Carbon*
  6. Ibrahim RK, El-Shafie A, Hin LS, Mohd NSB, Aljumaily MM, Ibraim S, et al.
    J Environ Manage, 2019 Apr 01;235:521-534.
    PMID: 30716672 DOI: 10.1016/j.jenvman.2019.01.070
    In this study two deep eutectic solvents (DESs) were prepared using ethylene glycol (EG) and two different ammonium-based salts. The potential of these DESs as novel agents for CNTs functionalization was examined by performing a comprehensive characterization study to identify the changes developing after the functionalization process. The impact of DESs was obvious by increasing the surface area of CNTs to reach 197.8 (m2/g), and by adding new functional groups to CNTs surface without causing any damage to the unique structure of CNTs. Moreover, CNTs functionalized with DESs were applied as new adsorbents for the removal of methyl orange (MO) from water. The adsorption conditions were optimized using RSM-CCD experimental design. The kinetics and the equilibrium adsorption data were analyzed using different kinetic and isotherm models. According to the regression results, adsorption kinetics data were well described by pseudo-second order model, whereas adsorption isotherm data were best represented by Langmuir isotherm model. The highest recorded maximum adsorption capacity (qmax) value was found to be 310.2 mg/g.
    Matched MeSH terms: Nanotubes, Carbon*
  7. Alayan HM, Alsaadi MA, AlOmar MK, Hashim MA
    Environ Technol, 2019 Jul;40(18):2400-2415.
    PMID: 29451094 DOI: 10.1080/09593330.2018.1441911
    This work demonstrated the synthesis of carbon nanotubes (CNTs) on powder activated carbon (PAC) impregnated with Ni-catalyst through chemical vapour deposition. The optimized effects of reaction temperature, time and feedstock flow rates on CNT growth were examined. Potassium permanganate (KMnO4) and potassium permanganate in acidic solution (KMnO4/H2SO4) were used to functionalize CNTs samples. A primary screening of methylene blue (MB) adsorption was conducted. The chemical, physical and morphological properties of the adsorbent with the highest removal efficiency were investigated using FESEM, EDX, TEM, BET surface area, RAMAN, TGA, FTIR, and zeta potential. The resulting carbon nanotube-loaded activated carbons possessed abundant pore structure and large surface area. The MB removal by the as-synthesized CNTs was more remarkable than that by the modified samples. Adsorption studies were carried out to evaluate the optimum conditions, kinetics and isotherms for MB adsorption process. The response surface methodology-central composite design (RSM-CCD) was used to optimize the adsorption process parameters, including pH, adsorbent dosage and contact time. The investigation of the adsorption behaviour demonstrated that the adsorption was well fitted with the pseudo-second-order model and Langmuir isotherm with the maximum monolayer adsorption capacity of 174.5 mg/g. Meanwhile, the adsorption of MB onto adsorbent was driven by the electrostatic attraction and π-π interaction. Moreover, the as-obtained CNT-PAC exhibited good reusability after four repeated operations. In view of these empirical findings, the low-cost CNT-PAC has potential for removal of MB from aqueous solution.
    Matched MeSH terms: Nanotubes, Carbon*
  8. Zhao X, Gopinath SCB, Zhao W
    Biotechnol Appl Biochem, 2023 Apr;70(2):502-508.
    PMID: 35661417 DOI: 10.1002/bab.2372
    Abdominal aortic aneurysm (AAA), a medical complication, occurs when the aortic area becomes swollen and very large. It is mandatory to identify AAA to avoid the breakdown of aneurysms. C-reactive protein (CRP) has been recognized as one of the biomarkers for identifying AAA due to the possibility of CRP produced in vascular tissue, which contributes to the formation of an aneurysm, and it is elevated in patients with a ruptured AAA. This research work was designed to develop an immunosensor on a multiwalled carbon nanotube (MWCNT)-modified surface to quantify the CRP level. Anti-CRP specificity was constructed on the MWCNT surface through a silane linker to interact with CRP. The detection limit of CRP was calculated as 100 pM with an R2 (determination coefficient) value of 0.9855 (y = 2.3446x - 1.9922) on a linear regression graph. The dose-dependent linear pattern was registered from 200 to 3000 pM and attained the saturation level during binding at 3000 pM. Furthermore, serum-spiked CRP showed a clear increase in the current response, proving the specific recognition of CRP in biological samples. This designed biosensor identifies CRP at a lower level and can help diagnose AAA.
    Matched MeSH terms: Nanotubes, Carbon*
  9. Singh R, Samuel MS, Ravikumar M, Ethiraj S, Kirankumar VS, Kumar M, et al.
    Chemosphere, 2023 Dec;344:140311.
    PMID: 37769916 DOI: 10.1016/j.chemosphere.2023.140311
    The carbon dioxide (CO2) crisis is one of the world's most urgent issues. Meeting the worldwide targets set for CO2 capture and storage (CCS) is crucial. Because it may significantly reduce energy consumption compared to traditional amine-based adsorption capture, adsorption dependant CO2 capture is regarded as one of the most hopeful techniques in this paradigm. The expansion of unique, critical edge adsorbent materials has received most of the research attention to date, with the main objective of improving adsorption capacity and lifespan while lowering the temperature of adsorption, thereby lowering the energy demand of sorbent revival. There are specific materials needed for each step of the carbon cycle, including capture, regeneration, and conversion. The potential and efficiency of metal-organic frameworks (MOFs) in overcoming this obstacle have recently been proven through research. In this study, we pinpoint MOFs' precise structural and chemical characteristics that have contributed to their high capture capacity, effective regeneration and separation processes, and efficient catalytic conversions. As prospective materials for the next generation of energy storage and conversion applications, carbon-based compounds like graphene, carbon nanotubes, and fullerenes are receiving a lot of interest. Their distinctive physicochemical characteristics make them suitable for these popular study topics, including structural stability and flexibility, high porosity, and customizable physicochemical traits. It is possible to precisely design the interior of MOFs to include coordinatively unsaturated metal sites, certain heteroatoms, covalent functionalization, various building unit interactions, and integrated nanoscale metal catalysts. This is essential for the creation of MOFs with improved performance. Utilizing the accuracy of MOF chemistry, more complicated materials must be built to handle selectivity, capacity, and conversion all at once to achieve a comprehensive solution. This review summarizes, the most recent developments in adsorption-based CO2 combustion capture, the CO2 adsorption capacities of various classes of solid sorbents, and the significance of advanced carbon nanomaterials for environmental remediation and energy conversion. This review also addresses the difficulties and potential of developing carbon-based electrodes for energy conversion and storage applications.
    Matched MeSH terms: Nanotubes, Carbon*
  10. Mohammad Haniff MA, Lee HW, Bien DC, Teh AS, Azid IA
    Nanoscale Res Lett, 2014;9(1):49.
    PMID: 24472487 DOI: 10.1186/1556-276X-9-49
    This paper presents a functionalized, horizontally oriented carbon nanotube network as a sensing element to enhance the sensitivity of a pressure sensor. The synthesis of horizontally oriented nanotubes from the AuFe catalyst and their deposition onto a mechanically flexible substrate via transfer printing are studied. Nanotube formation on thermally oxidized Si (100) substrates via plasma-enhanced chemical vapor deposition controls the nanotube coverage and orientation on the flexible substrate. These nanotubes can be simply transferred to the flexible substrate without changing their physical structure. When tested under a pressure range of 0 to 50 kPa, the performance of the fabricated pressure sensor reaches as high as approximately 1.68%/kPa, which indicates high sensitivity to a small change of pressure. Such sensitivity may be induced by the slight contact in isolated nanotubes. This nanotube formation, in turn, enhances the modification of the contact and tunneling distance of the nanotubes upon the deformation of the network. Therefore, the horizontally oriented carbon nanotube network has great potential as a sensing element for future transparent sensors.
    Matched MeSH terms: Nanotubes, Carbon
  11. Tan ML, Lentaris G, Amaratunga Aj G
    Nanoscale Res Lett, 2012;7(1):467.
    PMID: 22901374
    The performance of a semiconducting carbon nanotube (CNT) is assessed and tabulated for parameters against those of a metal-oxide-semiconductor field-effect transistor (MOSFET). Both CNT and MOSFET models considered agree well with the trends in the available experimental data. The results obtained show that nanotubes can significantly reduce the drain-induced barrier lowering effect and subthreshold swing in silicon channel replacement while sustaining smaller channel area at higher current density. Performance metrics of both devices such as current drive strength, current on-off ratio (Ion/Ioff), energy-delay product, and power-delay product for logic gates, namely NAND and NOR, are presented. Design rules used for carbon nanotube field-effect transistors (CNTFETs) are compatible with the 45-nm MOSFET technology. The parasitics associated with interconnects are also incorporated in the model. Interconnects can affect the propagation delay in a CNTFET. Smaller length interconnects result in higher cutoff frequency.
    Matched MeSH terms: Nanotubes, Carbon
  12. Ismail MA, Harun SW, Zulkepely NR, Nor RM, Ahmad F, Ahmad H
    Appl Opt, 2012 Dec 20;51(36):8621-4.
    PMID: 23262603 DOI: 10.1364/AO.51.008621
    We demonstrate a simple and low cost mode-locked erbium-doped fiber laser (EDFL) operating in the nanosecond region using a single-walled carbon nanotube (SWCNT)-based saturable absorber (SA). A droplet of SWCNT solution is applied on the end of a fiber ferrule, which is then mated to another clean connector ferrule to construct an SA. Then the SA is integrated into a ring EDFL cavity for nanosecond pulse generation. The EDFL operates at around 1570.4 nm, with a soliton-like spectrum with small Kelly sidebands, which confirms the attainment of the anomalous dispersion. It produces a soliton pulse train with a 332 ns width, repetition rate of 909.1 kHz, an average output power of 0.31 mW, and energy of 0.34 nJ at the maximum pump power of 130.8 mW.
    Matched MeSH terms: Nanotubes, Carbon
  13. Yang Y, Fedorov G, Shafranjuk SE, Klapwijk TM, Cooper BK, Lewis RM, et al.
    Nano Lett., 2015 Dec 09;15(12):7859-66.
    PMID: 26506109 DOI: 10.1021/acs.nanolett.5b02564
    Van Hove singularities (VHSs) are a hallmark of reduced dimensionality, leading to a divergent density of states in one and two dimensions and predictions of new electronic properties when the Fermi energy is close to these divergences. In carbon nanotubes, VHSs mark the onset of new subbands. They are elusive in standard electronic transport characterization measurements because they do not typically appear as notable features and therefore their effect on the nanotube conductance is largely unexplored. Here we report conductance measurements of carbon nanotubes where VHSs are clearly revealed by interference patterns of the electronic wave functions, showing both a sharp increase of quantum capacitance, and a sharp reduction of energy level spacing, consistent with an upsurge of density of states. At VHSs, we also measure an anomalous increase of conductance below a temperature of about 30 K. We argue that this transport feature is consistent with the formation of Cooper pairs in the nanotube.
    Matched MeSH terms: Nanotubes, Carbon
  14. Muniandy S, Teh SJ, Thong KL, Thiha A, Dinshaw IJ, Lai CW, et al.
    Crit Rev Anal Chem, 2019;49(6):510-533.
    PMID: 30648398 DOI: 10.1080/10408347.2018.1561243
    The development of easy to use, rapid and sensitive methods for direct detection of foodborne bacterial pathogens has become significantly important due to their impact on human health. In recent years, carbon nanomaterials have been adapted in the fabrication of electrochemical biosensors due to their exceptional combination of intrinsic properties such as high conductivity, stability and biocompatibility that render them as a promising candidate for bio-sensing material. The scope of this review is to provide a brief history of the current methods and different types of electrochemical biosensors used for the detection of bacterial pathogens. We primarily focus on the recent progress and applications of graphene, carbon nanotubes and their derivatives in electrochemical biosensors for foodborne bacterial pathogens detection. Finally, the status and future prospects of carbon-based electrochemical biosensors are also reviewed and discussed.
    Matched MeSH terms: Nanotubes, Carbon
  15. Chai, S.P., Zein, S.H.S., Mohamed, A.R.
    ASM Science Journal, 2008;2(1):57-64.
    MyJurnal
    Since the discovery of carbon nanotubes (CNTs) in 1991, a fundamental question still remained on how to control morphologically the synthesis of CNTs. This task has always been a challenge. In this paper, we report the results that we have published previously with the aim of sharing the possible controlled synthesis approach via this novel production method. Findings demonstrated that various CNTs could be synthesized by using specially developed supported catalysts from the catalytic decomposition of methane. These synthesized CNTs include carbon nanofibres, single-walled and multi-walled CNTs, Y-junction CNTs and CNTs with special morphologies. It was also revealed that catalyst composition and reaction parameters played an important role in controlling the morphology and type of CNTs formed. The synthesis of CNTs with various morphologies is important because this can enrich the nanostructures of the carbon family. This finding also provides useful data for better understanding of the parameters that govern the growth mechanism of CNTs which may be required in the near future for enhanced controlled synthesis of CNTs.
    Matched MeSH terms: Nanotubes, Carbon
  16. Noor Erna Fatini Mohd, Mariatti Jaafar, Tuti Katrina Abdullah
    MyJurnal
    Carbon fiber reinforced epoxy (CFRE) is commonly been used in automotive and aviation industries. However, CFRE composite exhibits the problem of adherence between fiber and matrix. The interface between carbon fiber (CF) and epoxy becomes a weak zone and leads to the debonding defect of fiber and low mechanical properties of composites. The main focus of this study is to fabricate CFRE using carbon nanotubes (CNTs), as the hybrid reinforcement with CF. Ultrasonic method is used to disperse CNTs in distilled water for 20 minutes, followed by deposition of CNTs on CF using electrophoretic deposition (EPD) technique. Hand lay-up assisted vacuum bagging is employed to fabricate CNTs/CF/Epoxy composite. From morphologies, surface topography and peel off testing, it can be confirmed that 30 minutes deposition allowed more CNTs to deposit on CF. The flexural properties shows that 30 minutes deposition inherited high flexural strength, 67.4 MPa and modulus, 8490 MPa.
    Matched MeSH terms: Nanotubes, Carbon
  17. Toozandehjani, Meysam, Khamirul Amin Matori, Ostovan, Farhad, Sidek Abdul Aziz, Md Shuhazely Mamat, Oskoueian, Arshin
    MyJurnal
    Carbon nanotube reinforced aluminium matrix composites (Al-CNTs) have been widely used in aerospace and automotive industries where high quality and strength is required. The enhanced mechanical properties of Al-CNTs are closely related to processing technique due to challenges within production of these composite materials. In the current review, solid state processing techniques used for synthesizing Al-CNTs have been reviewed to provide an insight into the features and capabilities of each technique regarding the incorporation of CNT reinforcements. To conclude, the mechanical performance of Al-CNT composites is mainly decided by the capability of each technique in the dispersion of CNTs within the aluminum matrix.
    Matched MeSH terms: Nanotubes, Carbon
  18. Das R, Hamid SB, Annuar MS
    Sci Rep, 2016 10 10;6:33572.
    PMID: 27721429 DOI: 10.1038/srep33572
    The present study reported for the first time covalent immobilization of protocatechuate 3,4-dioxygenase (3,4-POD) onto functionalized multi-walled carbon nanotubes (F-MWCNT) for degrading the toxic 3,4-dihydroxybenzoic acid (3,4-DHBA) pollutant in water. The F-MWCNTs had a maximum 3,4-POD loading of 1060 μg/mg. Immobilized 3,4 POD had 44% of relative structural changes to its free configurations. Nevertheless, >90% of relative activity and about 50% of catalytic efficiency were retained to the free enzyme. Immobilized 3,4-POD demonstrated higher alkaline stability and thermostability than the free 3,4-POD. The free and immobilized 3,4-POD lost 82% and 66% of relative activities, respectively after 180 min of incubations at 90 °C. Excellent shelf-life was observed for the immobilized 3,4-POD with residual activity of 56% compared with 41% and 39% of the free 3,4-POD at 4 °C and 25 °C over 30 days storage. Immobilized 3,4-POD showed >60% of catalytic activity retention even after ten-cycle uses, defraying the expenses of free 3,4-POD productions for long term uses. Finally, the immobilized 3,4-POD removed 71% of 3,4-DHBA from water in <4 h, paving its future application for water purification with reduced costs and time.
    Matched MeSH terms: Nanotubes, Carbon
  19. Tarawneh MA, Sahrim Ahmad, Rozaidi Rasid, Yahya S, Shamsul Bahri A, Ehnoum S, et al.
    Sains Malaysiana, 2011;40:1179-1186.
    The effect of various multi-walled carbon nanotubes (MWNTs) on the tensile properties of thermoplastic natural rubber (TPNR) nanocomposite was investigated. The nanocomposite was prepared using melt blending method. MWNTs were added to improve the mechanical properties of MWNTs/TPNR composites in different compositions of 1, 3, 5, and 7 wt.%. The results showed that the mechanical properties of nanocomposites were affected significantly by the composition and the properties of MWNTs. SEM micrographs confirmed the homogenous dispersion of MWNTs in the TPNR matrix and promoted strong interfacial adhesion between MWNTs and the matrix which was improved mechanical properties significantly.
    Matched MeSH terms: Nanotubes, Carbon
  20. Hosseingholi Pourasl A, Ariffin SHS, Ahmadi MT, Ismail R, Gharaei N
    Beilstein J Nanotechnol, 2019;10:644-653.
    PMID: 30931206 DOI: 10.3762/bjnano.10.64
    Nanomaterial-based sensors with high sensitivity, fast response and recovery time, large detection range, and high chemical stability are in immense demand for the detection of hazardous gas molecules. Graphene nanoribbons (GNRs) which have exceptional electrical, physical, and chemical properties can fulfil all of these requirements. The detection of gas molecules using gas sensors, particularly in medical diagnostics and safety applications, is receiving particularly high demand. GNRs exhibit remarkable changes in their electrical characteristics when exposed to different gases through molecular adsorption. In this paper, the adsorption effects of the target gas molecules (CO and NO) on the electrical properties of the armchair graphene nanoribbon (AGNR)-based sensor are analytically modelled. Thus, the energy dispersion relation of AGNR is developed considering the molecular adsorption effect using a tight binding (TB) method. The carrier velocity is calculated based on the density of states (DOS) and carrier concentration (n) to obtain I-V characteristics and to monitor its variation in the presence of the gas molecules. Furthermore, the I-V characteristics and energy band structure of the AGNR sensor are simulated using first principle calculations to investigate the gas adsorption effects on these properties. To ensure the accuracy of the proposed model, the I-V characteristics of the AGNR sensor that are simulated based both on the proposed model and first principles calculations are compared, and an acceptable agreement is achieved.
    Matched MeSH terms: Nanotubes, Carbon
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links