Attempts to produce colloidal platinum nanoparticles by using steady absorption spectra with various chemical-based reduction methods often resulted in the fast disappearance of the absorption maxima leaving reduced platinum nanoparticles with little information on their optical properties. We synthesized colloidal platinum nanoparticles in an aqueous solution of polyvinyl pyrrolidone by gamma radiolytic reduction method, which produced steady absorption spectra of fully reduced and highly pure platinum nanoparticles free from by-product impurities or reducing agent contamination. The average particle size was found to be in the range of 3.4–5.3 nm and decreased with increasing dose due to the domination of nucleation over ion association in the formation of metal nanoparticles by the gamma radiolytic reduction method. The platinum nanoparticles exhibit optical absorption spectra with two absorption peaks centered at about 216 and 264 nm and the peaks blue shifted to lower wavelengths with decreasing particle size. The absorption spectra of platinum nanoparticles were also calculated using quantum mechanical treatment and coincidently a good agreement was obtained between the calculated and measured absorption peaks at various particle sizes. This indicates that the 216 and 264-nm absorption peaks of platinum nanoparticles conceivably originated from the intra-band transitions of conduction electrons of (n = 5, l = 2) and (n = 6, l = 0) energy states respectively to higher energy states. The absorption energies, i.e., conduction band energies of platinum nanoparticles derived from the absorption peaks increased with increasing dose and decreased with increasing particle size.
Reducing the size of food particles is crucial for herbivores. Seasonal dietary changes are known to influence animals' chewing efficiency. Proboscis monkeys (Nasalis larvatus) are foregut fermenters, with a high chewing efficiency allowing them to achieve very fine faecal particles. In this study, we investigated how proboscis monkeys' chewing efficiency varies between wet and dry seasons, hypothesising differences possibly related to diet change. Faecal particle size analysis is an established approach to estimate chewing efficiency in mammalian herbivores. We analysed 113 proboscis monkey faecal samples collected in the Lower Kinabatangan Wildlife Sanctuary, between 2015 and 2017. By following standard sieve analysis protocols, we measured a mean particle size MPS0.025-8 of 0.45 ± 0.14 mm, and confirmed a previous result that proboscis monkeys have a very low faecal MPS. This study highlights a seasonal influence on proboscis monkeys' chewing efficiency, with smaller MPS (better chewing efficiency) during the wet season. During that time of the year, individuals may potentially change their diet, as all faecal samples contained intact seeds. Whether the seasonal MPS difference in proboscis monkeys is smaller than in other colobines due to their "rumination" strategy remains to be investigated.
This review presents an introduction to the synthesis of metallic nanoparticles by radiation-induced method, especially gamma irradiation. This method offers some benefits over the conventional methods because it provides fully reduced and highly pure nanoparticles free from by-products or chemical reducing agents, and is capable of controlling the particle size and structure. The nucleation and growth mechanism of metallic nanoparticles are also discussed. The competition between nucleation and growth process in the formation of nanoparticles can determine the size of nanoparticles which is influenced by certain parameters such as the choice of solvents and stabilizer, the precursor to stabilizer ratio, pH during synthesis, and absorbed dose.
In this study, the particle size distribution and concentration of metallic elements of solvent- and water-based paint dust from bulk dust collected from dust-collecting hoppers were determined. The mean particle size diameter over a 12-week sampling period was determined using a particle size analyzer. The metals composition and concentration of the dust were determined via acid digestion technique followed by concentration analysis using inductively coupled plasma. The volume weighted mean particle diameters were found to be 0.941+/-0.016 and 8.185+/-0.201 microm for solvent- and water-based paint dust, respectively. The mean concentrations of metals in solvent-based paint dust were found to be 100+/-20.00 microg/g (arsenic), 1550+/-550.00 microg/g (copper), 15,680+/-11,780.00 microg/g (lead) and 30,460+/-10,580.00 microg/g (zinc) while the mean concentrations of metals in water-based paint dust were found to be 20.65+/-6.11 microg/g (arsenic), 9.14+/-14.65 microg/g (copper), 57.46+/-22.42 microg/g (lead) and 1660+/-1260 microg/g (zinc). Both paint dust types could be considered as hazardous since almost all of the dust particles were smaller than 10 microm. Particular emphasis on containment of solvent-based paint dust particles should be given since it was shown that they were very fine in size (<1 microm) and had high lead and zinc concentrations.
This study aimed to improve the colloidal stability of yttria-stabilized tetragonal zirconia polycrystalline (Y-TZP)
suspension through colloidal processing to obtain highly translucent Y-TZP. Agglomeration is often the main complication
in the processing of nanosized Y-TZP as it deteriorates mechanical and optical properties. Thus, colloidal processing
is necessary to mitigate the agglomeration in Y-TZP. The colloidal stability of Y-TZP suspension plays a key role for the
success of colloidal processing. In this study, colloidal processing was conducted at several stages, namely, dispersant
addition, pH adjustment and sedimentation. Changes in particle size and zeta potential at various stages were recorded.
The suspensions were then slip-casted to form green bodies. Green bodies were sintered and characterized for density
and translucency. The results showed that dispersant addition followed by pH adjustment effectively dispersed soft
agglomerates by introducing electrosteric stabilization, whereas sedimentation successfully segregated hard agglomerates
and contributed excellent colloidal stability. With high colloidal stability, the translucency of Y-TZP was improved by
approximately 30%. This study demonstrated different colloidal processing stages and proved that high colloidal stability
and fine particle size are vital to produce highly translucent Y-TZP.
Fast and efficient separation remains a big challenge in high performance liquid chromatography (HPLC). The need for higher efficiency and resolution in separation is constantly in demand. To achieve that, columns developed are rapidly moving towards having smaller particle sizes and internal diameters (i.d.). However, these parameters will lead to high back-pressure in the system and will burden the pumps of the HPLC instrument. To address this limitation, monolithic columns, especially silica-based monolithic columns have been introduced. These columns are being widely investigated for fast and efficient separation of a wide range of molecules. The present article describes the current methods developed to enhance the column efficiency of particle packed columns and how silica monolithic columns can act as an alternative in overcoming the low permeability of particle packed columns. The fundamental processes behind the fabrication of the monolith including the starting materials and the silica sol-gel process will be discussed. Different monolith derivatization and end-capping processes will be further elaborated and followed by highlights of the performance such monolithic columns in key applications in different fields with various types of matrices.
The present study is aimed to prepare κ-carrageenan microparticles for the encapsulation of model drug, coenzyme Q10 (CoQ10). A face-centered central composite design was employed to study the effects of three different formulation variables (κ-carrageenan, emulsifier, and oil). The powder yield was found inversely affected by the κ-carrageenan and oil concentration. The encapsulation efficiency was maximized in the region of the middle level κ-carrageenan concentration, the high level emulsifier concentration, and the low level oil concentration. The emulsifier concentration was the most influential variable on the particle size of powder. The optimal formulation was reported as 0.91% (w/v) κ-carrageenan concentration, 0.64% (w/v) emulsifier, and 1.0% (w/w) oil. Both differential scanning colorimeter and X-ray diffraction analyses proved that incorporation of CoQ10 into κ- carrageenan microcapsules resulted in amorphous powder with significantly (p<0.05) higher water solubility compared to pure CoQ10 and physical mixture in the crystalline form.
Nowadays, PM2.5 concentrations greatly influence indoor air quality in subways and threaten passenger and staff health because PM2.5 not only contains heavy metal elements, but can also carry toxic and harmful substances due to its small size and large specific surface area. Exploring the physicochemical and distribution characteristics of PM2.5 in subways is necessary to limit its concentration and remove it. At present, there are numerous studies on PM2.5 in subways around the world, yet, there is no comprehensive and well-organized review available on this topic. This paper reviews the nearly twenty years of research and over 130 published studies on PM2.5 in subway stations, including aspects such as concentration levels and their influencing factors, physicochemical properties, sources, impacts on health, and mitigation measures. Although many determinants of station PM2.5 concentration have been reported in current studies, e.g., the season, outdoor environment, and station depth, their relative influence is uncertain. The sources of subway PM2.5 include those from the exterior (e.g., road traffic and fuel oil) and the interior (e.g., steel wheels and rails and metallic brake pads), but the proportion of these sources is also unknown. Control strategies of PM mainly include adequate ventilation and filtration, but these measures are often inefficient in removing PM2.5. The impacts of PM2.5 from subways on human health are still poorly understood. Further research should focus on long-term data collection, influencing factors, the mechanism of health impacts, and PM2.5 standards or regulations.
Aim: This study was aimed at evaluating the anticancer potential of curcumin-loaded poly(lactic-co-glycolic acid) (PLGA) based nanoparticles (NPs) in MDA-MB231 human breast cancer cells. Methods: Curcumin-loaded PLGA NPs were developed using a modified solvent evaporation technique. Physical characterization was performed on the formulated NPs. Furthermore, in vitro experiments were conducted to study the biological activity of the curcumin-loaded NPs. Results: Curcumin-loaded PLGA NPs demonstrated high encapsulation efficiency and sustained payload release. Moreover, the NPs exhibited a significant reduction in cell viability, cell migration and cell invasion in the MDA-MB231 cells. Conclusion: The study revealed that the formulated curcumin-loaded PLGA NPs possessed significant anti-metastatic properties. The findings showcased the possible potential of curcumin-loaded NPs in the management of debilitating conditions such as cancer. In addition, this study could form the basis for further research and advancements in this area.
This study presents an examination on the correlation of sonication operating condition, sludge property, formation and behaviour of cavitation bubbles in sludge disruption under low-frequency ultrasound sonication. The influence of sonication time, sonication density, type of sludge and solids content on the disruption was evaluated. The most vigorous particle disruption was achieved in the initial period of sonication, which subsided subsequently. The explosive effect was likely due to the rapid cavitation arising from powerful transient bubbles generated in fractions of microseconds. A rating for the type of sludge was derived based on the finding that particles in secondary sludge were more readily disrupted than both primary sludge and mixed sludge. While sonication density exhibited the most significant role in cavitation bubble formation and behaviour, particle disruption could be optimised for energy input by sonicating at higher sonication density and shorter sonication time. Based on theoretical consideration, it was deduced that within an optimum sludge solids content ranging between 2.3% and 3.2%, superior particle disruption could be accomplished within a minute for secondary sludge sonicated at a density of 0.52 W/mL. Useful guidelines for sonication system installation, equipment protection and process reliability could be established from knowledge derived from a good understanding on the influence of solids content on sludge sonication.
Media components such as wheat flour, MgSO4 and particle size were screened by Placket Burman design (PBD) while the operating range was fixed by one-factor-at-a-time method (OFAT), primarily for the enrichment of cassava peels as animal feed. Optimization of the selected media components was carried out using Face–Centered Central Composite Design (FCCCD) of the Response Surface Methodology (RSM) and the responses were measured in term of protein and lignin contents. Statistical analysis of the result showed that the quadratic term of wheat flour and the interaction between wheat flour and particle size were highly significant (P
In this study, we have employed a photocatalytic method to restore the liquid effluent from a palm oil mill in Malaysia. Specifically, the performance of both TiO2 and ZnO was compared for the photocatalytic polishing of palm oil mill effluent (POME). The ZnO photocatalyst has irregular shape, bigger in particle size but smaller BET specific surface area (9.71 m2/g) compared to the spherical TiO2 photocatalysts (11.34 m2/g). Both scavenging study and post-reaction FTIR analysis suggest that the degradation of organic pollutant in the TiO2 system has occurred in the bulk solution. In contrast, it is necessary for organic pollutant to adsorb onto the surface of ZnO photocatalyst, before the degradation took place. In addition, the reactivity of both photocatalysts differed in terms of mechanisms, photocatalyst loading and also the density of photocatalysts. From the stability test, TiO2 was found to offer higher stability, as no significant deterioration in activity was observed after three consecutive cycles. On the other hand, ZnO lost around 30% of its activity after the 1st-cycle of photoreaction. The pH studies showed that acidic environment did not improve the photocatalytic degradation of the POME, whilst in the basic environment, the reaction media became cloudy. In addition, longevity study also showed that the TiO2 was a better photocatalyst compared to the ZnO (74.12%), with more than 80.0% organic removal after 22 h of UV irradiation.
This paper presents a suitable and unique system for observing dielectrophoretic particle separation in a microfluidic device. Details presented on the experimental setup used will enable real time examination, monitoring and analysis of carboxylate-modified latex sphere particles in a colloidal mixture. Observations of the particles were made possible through an optical setup that illuminates the particles that went through the microelectrode array in the microchannel that was controlled by two analog signal generators. Through the setup, it was easily observed that the latex sphere particles move at a flow rate of 0.2 μl/s without colliding or overlapping on each other and successfully separated in two bands left and right. The new separation of one finest particles size for finest purification with respect to frequency was also observed, obtained and analysed.
The objective of this study was to evaluate the effects of milling methods on tensile properties of polypropylene (PP) / oil palm mesocarp fibre (OPMF) biocomposites. Two types of mills were used; Wiley mill (WM) and disc mill (DM). Ground OPMF from each milling process was examined for its particle size distribution and aspect ratio by sieve and microscopic analyses, respectively. Results showed that DM-OPMF had smaller diameter fibre with uniform particle size compared to the WM-OPMF. Surface morphology study by SEM showed that DM-OPMF had rougher surface compared to WM-OPMF. Furthermore, it was found that PP/DM-OPMF biocomposite had higher tensile strength compared to PP/WM-OPMF, with almost two-fold. Thus, it is suggested that small diameter and uniform size fibre may improve stress transfer and surface contact between the fibre and polymer matrix and cause well dispersion of filler throughout the polymer resulted in better tensile strength of PP/DM-OPMF Compared to PP/WM-OPMF biocomposite. Overall, it can be concluded that disc milling could serve as a simple and effective grinding method for improving the tensile properties of biocomposite.
The long term objective of this research is to look into the possibility of replacing soil strength parameters such as cohesion and angle of friction with electrical resistivity value for the purpose of computing among others, factor of safety in slopes or bearing capacity of soil. This paper however is limited to the investigation of correlation between electrical resistivity with some selected soil parameters. Electrical resistivity tests, using a basic multi meter, steel moulds and other related equipment, were conducted in the laboratory on soil samples with variations in soil type, compaction energy and moisture content. The samples consisted of predominantly clay, silt and sandy size particles and were compacted in a 100 x 100 mm square mould, while the corresponding electrical resistivity tests were carried out using the disc electrode method in accordance to BS 1377. The values of the electrical parameters such as voltage, current and resistance, with the corresponding value of soil parameters such as cohesion, angle of friction and moisture content, were measured and recorded. The results of the tests produced some initial crude relationships between electrical resistivity and the selected soil parameters. The strongest correlation between electrical resistivity and angle of internal friction, φ, was obtained from the clay size samples with R2 of 0.824, while the maximum correlation between electrical resistivity and moisture content again was obtained through the clay samples with R2 of 0.818. From the other results and graphs analyzed, some consistencies and specific trends of behaviour observed gave some early indications that a more detail and precise correlation between electrical resistivity and soil strength parameters could be very well possible in future.
β-tricalcium phosphate (β-TCP) powders were synthesized by using various particles sizes (40 nm – 780 μm) calcium carbonate (CaCO3) and phosphoric acid (H3PO4) at room temperature (25 ˚C). The synthesized powders were characterized by using X-Ray Diffraction (XRD) method. The purity of β-TCP powders were determined from XRD pattern while the crystallite size of β-TCP powders were calculated by using Scherrer equation. Results shows that the purity of β-TCP powders were ranged from 20.33 % to 81.94 % while the crystallite size of β- TCP powders were ranged from 0.04391 μm to 0.06751 μm. From this work, particle size of CaCO3 will influenced the purity but not the mean crystallite size of synthesized β-TCP.
Silicon dioxide (SiO2) has been extensively studied due to their unique properties that make it desirable for many applications ranging from electronic, catalysis, pigment as well as sensors. Multitude of methods and processes are established with the ability to manipulate and control the key properties that can cater for specific applications. Stober method is a very simple and easy for up-scale production of SiO2. This paper presents the experimental study on the effect of synthesis parameter on the morphology of SiO2 synthesized via Stober method. Three parameters were investigated such as concentration of catalyst, concentration of precursor and percentage of water content. The obtained samples were characterized using scanning electron microscopy (SEM) analysis. The findings showed that the size of particles produced is dependent on the synthesis parameter. In this study, particles size ranging from 50 nm to >100 nm are easily produced. The sphere size of SiO2 can be increased by increasing the concentration of ammonia hydroxide catalyst, the concentration of TEOS, as well as the percentage of water content.
The rheological properties, microstructure, textural properties, colour and droplet size distribution of mayonnaise-like emulsion models prepared using 10-30wt.% of palm olein-based diacylglycerol (POL-DAG) oil were compared with those of the control (100wt.% VCO) model. There were significant (P<0.05) differences in the particle size distribution of the oil droplets, the textural properties, and the rheological properties of the various emulsion models. The rheological analysis included the determination of the flow curves, yield stress, thixotropy, apparent viscosity, and viscoelastic parameters. The concentrated oil-in-water (O/W) emulsion with 30wt.% POL-DAG substitution exhibited high thixotropy. The POL-DAG content had a substantial effect on the rheological properties of yield stress, storage modulus (G') and loss modulus (G″). The pseudoplastic behaviour of the emulsions was demonstrated. The size of the particles in the 30% POL-DAG-substituted emulsion was dramatically increased after one day and 30days of storage. All of the emulsion samples with POL-DAG substituted for VCO showed a relatively non-uniform bimodal droplet size distribution after one day of storage. In general, substitution of 10-20wt.% POL-DAG oil is appropriate for preparing O/W emulsions that had flow curves and textural properties similar to those of the control sample.
Palm kernel cake (PKC), a by-product of the palm oil industry is limited in its use as a feed ingredient for poultry due to its high fibre and lignin content. The presence of these antinutritive components is the result of shells contaminating the by-product. The nutritive value of PKC has to be improved in order to increase its inclusion rate in poultry diet. In this study, PKC was subjected to a separation method using static cling and electrostatic separation to removethe shells present in PKC. Response surface methodology based on Box-Behnken design was used to optimize the separation method with moisture content (8 to 18%), particle size distribution (0.5 to 2.5 mm) and feed rate (20 to 200 g/min) as the independent variables evaluated. According to the regression coefficients and significance of the quadratic polynomial model, the optimum separation parameters were as follows: 13% PKC moisture content;
This paper investigates the field-dependent rheological properties of magnetorheological (MR) fluid used to fill in MR dampers after long-term cyclic operation. For testing purposes, a meandering MR valve was customized to create a double-ended MR damper in which MR fluid flowed inside the valve due to the magnetic flux density. The test was conducted for 170,000 cycles using a fatigue dynamic testing machine which has 20 mm of stroke length and 0.4 Hz of frequency. Firstly, the damping force was investigated as the number of operating cycles increased. Secondly, the change in viscosity of the MR fluid was identified as in-use thickening (IUT). Finally, the morphological observation of MR particles was undertaken before and after the long-term operation. From these tests, it was demonstrated that the damping force increased as the number of operating cycles increases, both when the damper is turn on (on-state) and off (off-state). It is also observed that the particle size and shape changed due to the long operation, showing irregular particles.