Displaying publications 41 - 60 of 80 in total

Abstract:
Sort:
  1. Laboratory tests on heat treatment of ballast water using engine waste heat
    Balaji R, Lee Siang H, Yaakob O, Koh KK, Adnan FAB, Ismail NB, et al.
    Environ Technol, 2018 May;39(9):1102-1114.
    PMID: 28425309 DOI: 10.1080/09593330.2017.1321691
    Waste heat recovery from shipboard machineries could be a potential source for heat treatment of ballast water. Similar to a shipboard schematic arrangement, a laboratory-scale engine-heat exchanger set-up harvesting waste heat from jacket water and exhaust gases was erected to test the level of species' mortalities. Mortalities were also assessed under experimental conditions for cultured and natural plankton communities at laboratory level. Effect of pump impellers on species' mortalities were also tested. Exposures between 60°C and 70°C for 60 sec resulted in 80-100% mortalities. Mortalities due to pump impeller effects were observed in the range of 70-100% for zooplankton. On the laboratory-scale arrangement, >95% mortalities of phytoplankton, zooplankton and bacteria were recorded. It was demonstrated that the temperature of tropical sea waters used as secondary coolant can be raised to cause species' mortalities, employing engine exhaust gases. The results also indicated that pump impeller effects will enhance species' mortalities. The limitations of the shipboard application of this method would be the large ballast volumes, flow rates and time for treatment.
  2. Bio-energy generation in an affordable, single-chamber microbial fuel cell integrated with adsorption hybrid system: effects of temperature and comparison study
    Tee PF, Abdullah MO, Tan IAW, Amin MAM, Nolasco-Hipolito C, Bujang K
    Environ Technol, 2018 Apr;39(8):1081-1088.
    PMID: 28417676 DOI: 10.1080/09593330.2017.1320433
    A microbial fuel cell (MFC) integrated with adsorption system (MFC-AHS) is tested under various operating temperatures with palm oil mill effluent as the substrate. The optimum operating temperature for such system is found to be at ∼35°C with current, power density, internal resistance (Rin), Coulombic efficiency (CE) and maximum chemical oxygen demand (COD) removal of 2.51 ± 0.2 mA, 74 ± 6 mW m-3, 25.4 Ω, 10.65 ± 0.5% and 93.57 ± 1.2%, respectively. Maximum current density increases linearly with temperature at a rate of 0.1772 mA m-2 °C-1, whereas maximum power density was in a polynomial function. The temperature coefficient (Q10) is found to be 1.20 between 15°C and 35°C. Present studies have demonstrated better CE performance when compared to other MFC-AHSs. Generally, MFC-AHS has demonstrated higher COD removals when compared to standalone MFC regardless of operating temperatures.

    ABBREVIATIONS: ACFF: activated carbon fiber felt; APHA: American Public Health Association; CE: Coulombic efficiency; COD: chemical oxygen demand; ECG: electrocardiogram; GAC: granular activated carbon; GFB: graphite fiber brush; MFC: microbial fuel cell; MFC-AHS: microbial fuel cell integrated with adsorption hybrid system; MFC-GG: microbial fuel cell integrated with graphite granules; POME: palm oil mill effluent; PTFE: polytetrafluoroethylene; SEM: scanning electron microscope.

  3. Generalized classification modeling of activated sludge process based on microscopic image analysis
    Khan MB, Nisar H, Ng CA, Lo PK, Yap VV
    Environ Technol, 2018 Jan;39(1):24-34.
    PMID: 28278778 DOI: 10.1080/09593330.2017.1293166
    The state of activated sludge wastewater treatment process (AS WWTP) is conventionally identified by physico-chemical measurements which are costly, time-consuming and have associated environmental hazards. Image processing and analysis-based linear regression modeling has been used to monitor the AS WWTP. But it is plant- and state-specific in the sense that it cannot be generalized to multiple plants and states. Generalized classification modeling for state identification is the main objective of this work. By generalized classification, we mean that the identification model does not require any prior information about the state of the plant, and the resultant identification is valid for any plant in any state. In this paper, the generalized classification model for the AS process is proposed based on features extracted using morphological parameters of flocs. The images of the AS samples, collected from aeration tanks of nine plants, are acquired through bright-field microscopy. Feature-selection is performed in context of classification using sequential feature selection and least absolute shrinkage and selection operator. A support vector machine (SVM)-based state identification strategy was proposed with a new agreement solver module for imbalanced data of the states of AS plants. The classification results were compared with state-of-the-art multiclass SVMs (one-vs.-one and one-vs.-all), and ensemble classifiers using the performance metrics: accuracy, recall, specificity, precision, F measure and kappa coefficient (κ). The proposed strategy exhibits better results by identification of different states of different plants with accuracy 0.9423, and κ 0.6681 for the minority class data of bulking.
  4. Hybrid soliwave technique for mitigating sulfate-reducing bacteria in controlling biocorrosion: a case study on crude oil sample
    Mohd Ali MKFB, Abu Bakar A, Md Noor N, Yahaya N, Ismail M, Rashid AS
    Environ Technol, 2017 Oct;38(19):2427-2439.
    PMID: 27875932 DOI: 10.1080/09593330.2016.1264486
    Microbiologically influenced corrosion (MIC) is among the common corrosion types for buried and deep-water pipelines that result in costly repair and pipeline failure. Sulfate-reducing bacteria (SRB) are commonly known as the culprit of MIC. The aim of this work is to investigate the performance of combination of ultrasound (US) irradiation and ultraviolet (UV) radiation (known as Hybrid soliwave technique, HyST) at pilot scale to inactivate SRB. The influence of different reaction times with respect to US irradiation and UV radiation and synergistic effect toward SRB consortium was tested and discussed. In this research, the effect of HyST treatment toward SRB extermination and corrosion studies of carbon steel coupon upon SRB activity before and after the treatment were performed using weight loss method. The carbon steel coupons immersed in SRB sample were exposed to HyST treatment at different time of exposure. Additionally, Field Emission Scanning Electron Microscopy coupled with Energy Dispersive X-ray Spectroscopy were used to investigate the corrosion morphology in verifying the end product of SRB activity and corrosion formation after treatment. Results have shown that the US irradiation treatment gives a synergistic effect when combined with UV radiation in mitigating the SRB consortium.
  5. Response of microcystin biosynthesis and its biosynthesis gene cluster transcription in Microcystis aeruginosa on electrochemical oxidation
    Gao Y, Shimizu K, Amano C, Wang X, Pham TL, Sugiura N, et al.
    Environ Technol, 2019 Nov;40(27):3593-3601.
    PMID: 29806796 DOI: 10.1080/09593330.2018.1482371
    Microcystin-LR (MC-LR), which is one of the most commonly found microcystins (MCs) in fresh water, has been proved to be a potential tumour promoter and classified as 2B by the International Agency for Research on Cancer. MC-LR decomposition and inhibition of MC-LR production in Microcystis aeruginosa were investigated under electrolysis condition using an electrolysis cell consisting of Ti/Pt electrodes and Nafion membrane. The relationship between the decrease in MC-LR concentration and transcription of MC-LR synthesis gene clusters was determined by performing real-time reverse transcription polymerase chain reaction (RT-qPCR) to monitor changes in the levels of transcription encoding mcyB and mcyD (cDNA to DNA) in M. aeruginosa NIES 1086 under electrolysis condition and three different conditions (i.e. oxygenated, air aerated and unaerated) as controls. Cell density decreased from day 2 under electrolysis than under the three controls. Intracellular MC-LR concentration was approximately 33 fg cell-1 under electrolysis from days 4 to 8, while those in the other conditions ranged in 40-50 fg cell-1. The mcyB transcription continuously decreased from day 2 to nondetectable level in day 6 under electrolysis, while this transcription was stabilised under the three controls. This result suggested that oxidative stress, such as hydroxyl radicals, played an important role in the down-regulation of mcyB and mcyD gene transcription level and the MC-LR concentration and cell density of M. aeruginosa.
  6. Green synthesis of copper nanoparticle using ionic liquid-based extraction from Polygonum minus and their applications
    Ullah H, Wilfred CD, Shaharun MS
    Environ Technol, 2019 Dec;40(28):3705-3712.
    PMID: 29873603 DOI: 10.1080/09593330.2018.1485751
    The present work reports the extraction of phenolic compounds from Polygonum minus using ionic liquid as extracting solvent. In this work, 1-Butyl-3-methylimidazolium hydrogen sulfate [BMIM][HSO4] was used for the extraction of bioactive compounds. Accordingly, ionic liquids based microwave-assisted extraction treatment for separating of bioactive compounds from polygonum minus was first performed in the present study. The results obtained in this work have high extraction yield in comparison with conventional solvent. UV/Vis results showed that microwave synthesis was fast, well dispersed and nanosized copper nanoparticle (CuNPs) in comparison with conventional synthesis. CuNPs was characterised by X-Rays diffractometer (XRD), Fourier transform infrared (FTIR), dynamic light scattering (DLS), field emission scanning electron microscopy combined with energy dispersive x-rays (FESEM-EDX), and thermogravimetric analysis (TGA). All the instrumental analyses confirmed the particles were nanosized. Furthermore, the antibacterial activity of as-synthesised CuNPs showed effective inhibitory zone against three different bacteria. The photocatalytic degradation of copper nanoparticles was studied using methylene blue (MB) and methyl orange (MO) dyes under UV light and degraded 99.9% within short time 8 and 7 min.
  7. Plant extract as environmental-friendly green catalyst for the reduction of hexavalent chromium in tannery effluent
    Johnson P, Loganathan C, Krishnan V, Sakayanathan P, Raji V, Vijayan S, et al.
    Environ Technol, 2018 Jun;39(11):1376-1383.
    PMID: 28488473 DOI: 10.1080/09593330.2017.1329355
    The aqueous extract of various plants like Coriandrum sativum (AECS), Alternanthera tenella colla (AEAT), Spermacoce hispida (AESH) and Mollugo verticillata (AEMV) was studied for its hexavalent chromium (CrVI) reduction property. Even though antioxidant activity was present, AEAT, AESH and AEMV did not reduce CrVI. AECS showed rapid and dose-dependent CrVI reduction. The efficient reduction of 50 mg/L of CrVI using AECS was attained in the presence of 250 µg/mL of starting plant material, incubating the reaction mixture at pH 2, 30°C and agitation at 190 rpm. Under such conditions, about 40 mg/L of CrVI was reduced at 3 h of incubation. FT-IR analysis revealed the involvement of phenols, alcohols, alpha-hydroxy acid and flavonoids present in the AECS for the CrVI reduction. These results indicate that not all the plant extracts with rich antioxidants are capable of reducing CrVI. Using the conditions standardized in the present study, AECS reduced about 80% of CrVI present in the tannery effluent. These results signify the application of AECS as an eco-friendly method in the wastewater treatment.
  8. Performance of modified anaerobic inclining-baffled reactor treating recycled paper mill effluent: effects of influent chemical oxygen demand concentration and hydraulic retention time
    Zwain HM, Aziz HA, Dahlan I
    Environ Technol, 2018 Jun;39(12):1557-1565.
    PMID: 28514902 DOI: 10.1080/09593330.2017.1332692
    The performance of modified anaerobic inclining-baffled reactor (MAI-BR) treating recycled paper mill effluent (RPME) was investigated by varying the influent chemical oxygen demand (CODin) concentration from 1000 to 4000 mg/L, and the hydraulic retention time (HRT) from 3 to 1 day, corresponding to an organic loading rate increase from 0.33 to 4 g COD/L day. Throughout 126 days of operation, a maximum removal efficiency of up to 96% of chemical oxygen demand (COD) and 99% of biological oxygen demand, methane (CH4) yield of 0.259 L CH4/g COD, and a stable effluent pH of 6.5 were achieved. Furthermore, the compartmental performance showed that most of the organic substrates were removed in the initial two compartments, resulting in low pH and alkalinity levels and a high concentration of volatile fatty acids. Overall, the results showed that the MAI-BR successfully treated RPME, and the performance was affected by the variation of HRT more than the CODin.
  9. Mass transfer kinetics of biosorption of nitrogenous matter from palm oil mill effluent by aerobic granules in sequencing batch reactor
    Fulazzaky MA, Nuid M, Aris A, Muda K
    Environ Technol, 2018 Sep;39(17):2151-2161.
    PMID: 28675960 DOI: 10.1080/09593330.2017.1351494
    Understanding of mass transfer kinetics is important for biosorption of nitrogen compounds from palm oil mill effluent (POME) to gain a mechanistic insight into future biological processes for the treatment of high organic loading wastewater. In this study, the rates of global and sequential mass transfer were determined using the modified mass transfer factor equations for the experiments to remove nitrogen by aerobic granular sludge accumulation in a sequencing batch reactor (SBR). The maximum efficiencies as high as 97% for the experiment run at [kLa]g value of 1421.8 h-1 and 96% for the experiment run at [kLa]g value of 9.6 × 1037 h-1 were verified before and after the addition of Serratia marcescens SA30, respectively. The resistance of mass transfer could be dependent on external mass transfer that controls the transport of nitrogen molecule along the experimental period of 256 days. The increase in [kLa]g value leading to increased performance of the SBR was verified to contribute to the future applications of the SBR because this phenomenon provides new insight into the dynamic response of biological processes to treat POME.
  10. Decolourization and biodegradation of azo dye methyl red by Rhodococcus strain UCC 0016
    Maniyam MN, Ibrahim AL, Cass AEG
    Environ Technol, 2020 Jan;41(1):71-85.
    PMID: 29923786 DOI: 10.1080/09593330.2018.1491634
    In the present study, locally isolated Rhodococcus strains were attempted as biological tools for methyl red removal, a mutagenic azo dye posing threat to the environment if left untreated. Rhodococcus strain UCC 0016 demonstrated superior methyl red-decolourizing activity of 100% after 24 h at static condition in comparison to Rhodococcus strain UCC 0008 which recorded 65% decolourization after 72 h. Optimization of physicochemical parameters at 30°C, pH 7 and supplementing glucose as the carbon source resulted in improved methyl red-decolourizing activity at static condition and reduced the time taken to achieve complete decolourization by 80%. Higher concentration of methyl red (5 g/L) was able to be decolourized completely within 10 h by adopting the technology of immobilization. The encapsulated cells of Rhodococcus strain UCC 0016 demonstrated higher substrate affinity (Km = 0.6995 g/L) and an accelerated rate of disappearance of methyl red (Vmax = 0.3203 g/L/h) compared to the free cells. Furthermore, the gellan gum beads could be reused up to nine batches without substantial loss in the catalytic activity indicating the economic importance of this protocol. Analysis of methyl red degradation products revealed no germination inhibition on Triticum aestivum and Vigna radiata demonstrating complete toxicity removal of the parent dye after biological treatment. The occurrence of new and altered peaks (UV-Vis and FTIR) further supported the notion that the removal of methyl red by Rhodococcus strain UCC 0016 was indeed through biodegradation. Therefore, this strain has a huge potential as a candidate for efficient bioremediation of wastewater containing methyl red.
  11. Passive bioremediation technology incorporating lignocellulosic spent mushroom compost and limestone for metal- and sulfate-rich acid mine drainage
    Muhammad SN, Kusin FM, Md Zahar MS, Mohamat Yusuff F, Halimoon N
    Environ Technol, 2017 Aug;38(16):2003-2012.
    PMID: 27745113 DOI: 10.1080/09593330.2016.1244568
    Passive bioremediation of metal- and sulfate-containing acid mine drainage (AMD) has been investigated in a batch study. Multiple substrates were used in the AMD remediation using spent mushroom compost (SMC), limestone, activated sludge (AS), and woodchips (WC) under anoxic conditions suitable for bacterial sulfate reduction (BSR). Limestones used were of crushed limestone (CLS) and uncrushed limestone, provided at two different ratios in mixed substrates treatment and varied by the proportion of SMC and limestone. The SMC greatly assisted the removals of sulfate and metals and also acted as an essential carbon source for BSR. The mixed substrate composed of 40% CLS, 30% SMC, 20% AS, and 10% WC was found to be effective for metal removal. Mn, Cu, Pb, and Zn were greatly removed (89-100%) in the mixed substrates treatment, while Fe was only removed at 65%. Mn was found to be removed at a greatly higher rate than Fe, suggesting important Mn adsorption onto organic materials, that is, greater sorption affinity to the SMC. Complementary with multiple treatment media was the main mechanism assisting the AMD treatment through microbial metal reduction reactions.
  12. Enhanced cyanide biodegradation by immobilized crude extract of Rhodococcus UKMP-5M
    Maniyam MN, Ibrahim AL, Cass AEG
    Environ Technol, 2019 Jan;40(3):386-398.
    PMID: 29032742 DOI: 10.1080/09593330.2017.1393015
    The capability of the crude extract of Rhodococcus UKMP-5M was enhanced by adopting the technology of immobilization. Among the matrices screened to encapsulate the crude extract, gellan gum emerged as the most suitable immobilization material, exceeding the activity of cyanide-degrading enzyme by 61% and 361% in comparison to alginate carrier and non-immobilized crude extract, respectively. Improved bead mechanical strength which supported higher biocatalyst activity by 63% was observed when concentration of gellan gum, concentration of calcium chloride, number of beads and bead size were optimized. The immobilized crude extract demonstrated higher tolerance towards broad range of pH (5-10) and temperature (30°C-40°C), superior cyanide-degrading activity over time and improved storage stability by maintaining 76% of its initial activity after 30 days at 4°C. Furthermore, repeated use of the gellan gum beads up to 20 batches without substantial loss in the catalytic activity was documented in the present study, indicating that the durability of the beads and the stability of the enzyme are both above adequate. Collectively, the findings reported here revealed that the utilization of the encapsulated crude extract of Rhodococcus UKMP-5M can be considered as a novel attempt to develop an environmentally favourable and financially viable method in cyanide biodegradation.
  13. Effect of air flow rate and C/N ratio on biological nitrogen removal through the CANON process treating reject water
    Mousavi SA, Mehralian M, Khashij M, Ibrahim S
    Environ Technol, 2018 Nov;39(22):2891-2899.
    PMID: 28820045 DOI: 10.1080/09593330.2017.1369578
    The CANON process is a promising method for nitrogen removal in wastewaters with low organic carbon content like reject water. This study investigated the effect of important factors for optimization of the CANON process through inhibition of nitrite-oxidizing bacteria (NOB). In the acclimation period, complete ammonium removal and 43.3% total N removal were obtained at hydraulic retention time of 12 h, temperature of 30°C ± 0.5°C and DO equal to 7-9 mg/L. The effects of air flow rate (AFR) (representative of DO), SRT and C/N were evaluated. Air flow rate was the most important factor for controlling the process, but the effect of SRT was negligible. When AFR was increased from 100 to 500 mL/min, both ammonium removal efficiency (33-43% to 81-83%) and nitrite accumulation (nitritation, 40 mgN/L to 100-120 mgN/L) were increased, but with increasing AFR to 1000 mL/min only ammonium removal efficiency was increased and because of better condition (high DO) for NOBs, nitritation was decreased. C/N had an effect like AFR of 1000 and only increased ammonium removal efficiency and total N removal. With increasing AFR and C/N, both OUR and AUR were increased, but SVI was decreased.
  14. Fatty acid profile from immobilised Chlorella vulgaris cells in different matrices
    Abu Sepian NR, Mat Yasin NH, Zainol N, Rushan NH, Ahmad AL
    Environ Technol, 2019 Apr;40(9):1110-1117.
    PMID: 29161985 DOI: 10.1080/09593330.2017.1408691
    The immobilisation of Chlorella vulgaris 211/11B entrapped in combinations of natural matrices to simplify the harvesting process was demonstrated in this study. Three combinations of matrices composed of calcium alginate (CA) and sodium alginate (SA), sodium carboxymethyl cellulose (CMC) and SA, and mixed matrices (SA, CA, and CMC) were investigated. The number of cells grown for each immobilised matrix to microalgae volume ratios (0.2:1-1:1) were explored and compared with using SA solely as a control. The optimum volume ratios obtained were 1:1 for SA, 0.3:1 for CA and SA, 1:1 for CMC and SA, and 0.3:1 for mixed matrices. The immobilised microalgae of mixed matrices exhibited the highest number of cells with 1.72 × 109 cells/mL at day 10 and 30.43% of oil extraction yield followed by CA and SA (24.29%), CMC and SA (13.00%), and SA (6.71%). Combining SA, CA, and CMC had formed a suitable structure which improved the growth of C. vulgaris and increased the lipid production compared to the immobilisation using single matrix. Besides, the fatty acids profile of the oil extracted indicates a high potential for biodiesel production.
  15. Carbon capture from natural gas using multi-walled CNTs based mixed matrix membranes
    Hussain A, Farrukh S, Hussain A, Ayoub M
    Environ Technol, 2019 Mar;40(7):843-854.
    PMID: 29161995 DOI: 10.1080/09593330.2017.1408696
    Most of the polymers and their blends, utilized in carbon capture membranes, are costly, but cellulose acetate (CA) being inexpensive is a lucrative choice. In this research, pure and mixed matrix membranes (MMMs) have been fabricated to capture carbon from natural gas. Polyethylene glycol (PEG) has been utilized in the fabrication of membranes to modify the chain flexibility of polymers. Multi-walled carbon nanotubes (MWCNTs) provide mechanical strength, thermal stability, an extra free path for CO2 molecules and augment CO2/CH4 selectivity. Membranes of pure CA, CA/PEG blend of different PEG concentrations (5%, 10%, 15%) and CA/PEG/MWCNTs blend of 10% PEG with different MWCNTs concentrations (5%, 10%, 15%) were prepared in acetone using solution casting techniques. Fabricated membranes were characterized using SEM, TGA and tensile testing. Permeation results revealed remarkable improvement in CO2/CH4 selectivity. In single gas experiments, CO2/CH4 selectivity is enhanced 8 times for pure membranes containing 10% PEG and 14 times for MMMs containing 10% MWCNTs. In mix gas experiments, the CO2/CH4 selectivity is increased 13 times for 10% PEG and 18 times for MMMs with 10% MWCNTs. Fabricated MMMs have a tensile strength of 13 MPa and are more thermally stable than CA membranes.
  16. Risk assessment of nitrate transport through subsurface layers and groundwater using experimental and modeling approach
    Alslaibi TM, Abunada Z, Abu Amr SS, Abustan I
    Environ Technol, 2018 Nov;39(21):2691-2702.
    PMID: 28789588 DOI: 10.1080/09593330.2017.1365936
    Landfills are one of the main point sources of groundwater pollution. This research mainly aims to assess the risk of nitrate [Formula: see text] transport from the unlined landfill to subsurface layers and groundwater using experimental results and the SESOIL model. Samples from 12 groundwater wells downstream of the landfill were collected and analyzed in 2008, 21 years after the landfill construction. The average [Formula: see text] concentration in the wells was 54 mg/L, slightly higher than the World Health Organization ([Formula: see text] 50 mg/L) standards. SESOIL model was used to predict the [Formula: see text] concentration at the bottom of the unsaturated zone. Results indicated that the current mean [Formula: see text] concentration at the bottom of the unsaturated zone is 75 mg/L. the model predicted that the level of NO3 will increased up to 325 mg/L within 30 years. Accordingly, the [Formula: see text] concentration in groundwater wells near the landfill area is expected to gradually increase with time. Although the current risk associated with the [Formula: see text] level might not be harm to adults, however, it might pose severe risks to both adults and infants in the near future due to [Formula: see text] leaching. Urgent mitigation measures such as final cell cover (cap), lining system and vertical expansion should be considered at the landfill to protect the public health in the area.
  17. Growth and optimization of carbon nanotubes in powder activated carbon for an efficient removal of methylene blue from aqueous solution
    Alayan HM, Alsaadi MA, AlOmar MK, Hashim MA
    Environ Technol, 2019 Jul;40(18):2400-2415.
    PMID: 29451094 DOI: 10.1080/09593330.2018.1441911
    This work demonstrated the synthesis of carbon nanotubes (CNTs) on powder activated carbon (PAC) impregnated with Ni-catalyst through chemical vapour deposition. The optimized effects of reaction temperature, time and feedstock flow rates on CNT growth were examined. Potassium permanganate (KMnO4) and potassium permanganate in acidic solution (KMnO4/H2SO4) were used to functionalize CNTs samples. A primary screening of methylene blue (MB) adsorption was conducted. The chemical, physical and morphological properties of the adsorbent with the highest removal efficiency were investigated using FESEM, EDX, TEM, BET surface area, RAMAN, TGA, FTIR, and zeta potential. The resulting carbon nanotube-loaded activated carbons possessed abundant pore structure and large surface area. The MB removal by the as-synthesized CNTs was more remarkable than that by the modified samples. Adsorption studies were carried out to evaluate the optimum conditions, kinetics and isotherms for MB adsorption process. The response surface methodology-central composite design (RSM-CCD) was used to optimize the adsorption process parameters, including pH, adsorbent dosage and contact time. The investigation of the adsorption behaviour demonstrated that the adsorption was well fitted with the pseudo-second-order model and Langmuir isotherm with the maximum monolayer adsorption capacity of 174.5 mg/g. Meanwhile, the adsorption of MB onto adsorbent was driven by the electrostatic attraction and π-π interaction. Moreover, the as-obtained CNT-PAC exhibited good reusability after four repeated operations. In view of these empirical findings, the low-cost CNT-PAC has potential for removal of MB from aqueous solution.
  18. Fabrication of calixarene-grafted magnetic nanocomposite for the effective removal of lead(II) from aqueous solution
    Kamboh MA, Wan Ibrahim WA, Rashidi Nodeh H, Zardari LA, Sanagi MM
    Environ Technol, 2019 Aug;40(19):2482-2493.
    PMID: 29464995 DOI: 10.1080/09593330.2018.1444100
    Magnetic nanocomposites adorned with calixarene were successfully prepared by immobilizing diethanolamine functionalized p-tert-butylcalix[4]arene (DEA-Calix) onto silica-coated magnetic nanoparticles (MNPs). The synthesis, surface morphology, purity, elemental composition and thermal stability of newly prepared nanocomposites were analyzed using FT-IR spectroscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDX), X-ray diffractometer (XRD), thermal gravimetric analysis (TGA) and vibrating sample magnetometer (VSM). Magnetic solid-phase adsorption (MSPA) was employed to explore the adsorption behavior of DEA-Calix-MNPs towards Pb(II) from water samples prior to its flame atomic absorption spectrometric analysis. The essential analytical factors governing the adsorption efficiency such as solution pH, mass of adsorbent, concentration and contact time have been investigated and optimized. The results depict that DEA-Calix-MNPs has excellent adsorption efficiency 97% (at pH 5.5) with high adsorption capacity of 51.81 mg g-1 for Pb(II) adsorption. Additionally, kinetic and equilibrium studies suggested that Pb(II) adsorption process follows a pseudo-second-order model and Langmuir isotherms, respectively. Real sample analysis also confirmed field applicability of the new DEA-Calix-MNPs adsorbent.
  19. Performance and kinetic evaluation of an integrated anaerobic-aerobic bioreactor in the treatment of palm oil mill effluent
    Chan YJ, Chong MF, Law CL
    Environ Technol, 2017 Apr;38(8):1005-1021.
    PMID: 27532518 DOI: 10.1080/09593330.2016.1217053
    This work presents the evaluation of biokinetic coefficients for a novel integrated anaerobic-aerobic bioreactor (IAAB) at different organic loading rates (OLRs) (10.5-22.5 g COD/L per day) treating palm oil mill effluent. The overall efficiencies of the chemical oxygen demand (COD) and biochemical oxygen demand (BOD) were more than 99% for OLR up to 19.5 g COD/L day with biogas production containing 48-64% of methane. The effluent quality remained stable (BOD 
  20. Swelling mechanism of urea cross-linked starch-lignin films in water
    Sarwono A, Man Z, Bustam MA, Subbarao D, Idris A, Muhammad N, et al.
    Environ Technol, 2018 Jun;39(12):1522-1532.
    PMID: 28524800 DOI: 10.1080/09593330.2017.1332108
    Coating fertilizer particles with thin films is a possibility to control fertilizer release rates. It is observed that novel urea cross-linked starch-lignin composite thin films, prepared by solution casting, swell on coming into contact with water due to the increase in volume by water uptake by diffusion. The effect of lignin content, varied from 0% to 20% in steps of 5% at three different temperatures (25°C, 35°C and 45°C), on swelling of the film was investigated. By gravimetric analysis, the equilibrium water uptake and diffusion coefficient decrease with lignin content, indicating that the addition of lignin increases the hydrophobicity of the films. When temperature increases, the diffusion coefficient and the amount of water absorbed tend to increase. Assuming that swelling of the thin film is by water uptake by diffusion, the diffusion coefficient is estimated. The estimated diffusion coefficient decreases from 4.3 to 2.1 × 10-7 cm2/s at 25°C, from 5.3 to 2.9 × 10-7 cm2/s at 35°C and from 6.2 to 3.8 × 10-7 cm2/s at 45°C depending on the lignin content. Activation energy for the increase in diffusion coefficient with temperature is observed to be 16.55 kJ/mol. An empirical model of water uptake as a function of percentage of lignin and temperature was also developed based on Fick's law.
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links