To overcome drawbacks in the conventional chemical route to synthesize eugenyl benzoate, immobilized Rhizomucor miehei lipase (RML) as the biocatalyst was proposed. The RML conjugated to a hybrid support consisting of biopolymers, chitosan (CS) and chitin nanowhiskers (CNWs). 1-ethyl-3-[3-dimethylaminopropyl]carbodiimide hydrochloride (EDAC) was used as the crosslinker to bind the lipase. Immobilization of RML was the highest on crosslinked CS/CNWs which gave a protein loading of ∼8.12 mg/g, corresponding to specific and residual activity of 537 U/g and 137%, respectively. Fourier transform infrared spectroscopy, thermogravimetric analysis-differential thermogravimetry, field emission scanning electron and atomic force microscopy of RML-CS/CNWs revealed that RML was successfully attached to the surface of crosslinked CS/CNWs. Under an optimized condition, the highest yield of eugenyl benzoate (56.3%) was attained after 5 h using 3 mg/mL of RML-CS/CNWs with molar ratio of eugenol: benzoic acid of 3:1, as compared to only 47.3% for the free RML. Analyses of FTIR and NMR on purified eugenyl benzoate affirmed that the ester was successfully produced in the enzymatic esterification. Therefore, the use of the RML-CS/CNWs biocatalysts appears promising to afford good yields of eugenyl benzoate within a relatively shorter reaction time.
The study reports the preparation of a composite consisting of magnetite coated with nanosilica extracted from oil palm leaves (OPL) ash as nanosupports for immobilization of Candida rugosa lipase (CRL) and its application for the synthesis of butyl butyrate. Results of immobilization parameters showed that ∼ 80% of CRL (84.5 mg) initially offered was immobilized onto the surface of the nanosupports to yield a maximum protein loading and specific activity of 67.5 ± 0.72 mg/g and 320.8 ± 0.42 U/g of support, respectively. Surface topography, morphology as well as information on surface composition obtained by Raman spectroscopy, atomic force microscopy, field emission scanning electron microscopy and transmission electron microscopy showed that CRL was successfully immobilized onto the nanosupports, affirming its biocompatibility. Under optimal conditions (3.5 mg/mL protein loading, at 45 ℃, 3 h and molar ratio 2:1 (1-butanol:n-butyric acid) the CRL/Gl-A-SiO2-MNPs gave a maximum yield of 94 ± 0.24% butyl butyrate as compared to 84 ± 0.32% in the lyophilized CRL. CRL/Gl-A-SiO2-MNPs showed an extended operational stability, retaining 50% of its initial activity after 17 consecutive esterification cycles. The results indicated that OPL derived nanosilica coated on magnetite can potentially be employed as carrier for lipase immobilization in replacement of the non-renewable conventionalsilica sources.
In previous studies of Lactococcus lactis, the levels of proteins secreted using heterologous signal peptides were observed to be lower than those obtained using the signal peptide from Usp45, the major secreted lactococcal protein. In this study, G1 (the native signal peptide of CGTase) and the signal peptide M5 (mutant of the G1 signal peptide) were introduced into L. lactis to investigate the effect of signal peptides on lactococcal protein secretion to improve secretion efficiency. The effectiveness of these signal peptides were compared to the Usp45 signal peptide. The highest secretion levels were obtained using the G1 signal peptide. Sequence analysis of signal peptide amino acids revealed that a basic N-terminal signal peptide is not absolutely required for efficient protein export in L. lactis. Moreover, the introduction of a helix-breaking residue in the H-region of the M5 signal peptide caused a reduction in the signal peptide hydrophobicity and decreased protein secretion. In addition, the optimization of cultivation conditions for recombinant G1-CGTase production via response surface methodology (RSM) showed that CGTase activity increased approximately 2.92-fold from 5.01 to 16.89 U/ml compared to the unoptimized conditions.
Enzymatic reactions involving lipases as catalyst in transesterification can be an excellent alternative to produce environmental-friendly biodiesel. In this study, lipase extracted from Cocoa Pod Husk (CPH) and immobilized through cross linked enzyme aggregate (CLEA) technology catalysed the transesterification of Jatropha curcas oil successfully. Face centered central composite design (FCCCD) under response surface methodology (RSM) was used to get the optimal conditions of 3% (w/w) enzyme loading, 4h reaction time and 1:6 oil/ethanol ratio to achieve the highest conversion of free fatty acid and glycerides into biodiesel (93%). The reusability of CLEA-lipase was tested and after seven cycles, the conversion percentage reduced to 58%. The results revealed that CLEA lipase from CPH is a potential catalyst for biodiesel production.
We isolated fifty-two strains from the marine aquaculture ponds in Malaysia that were evaluated for their lipid production and ammonium tolerance and four isolates were selected as new ammonium tolerant microalgae with high-lipid production: TRG10-p102 Oocystis heteromucosa (Chlorophyceae); TRG10-p103 and TRG10-p105 Thalassiosira weissflogii (Bacillariophyceae); and TRG10-p201 Amphora coffeiformis (Bacillariophyceae). Eicosapentenoic acid (EPA) in three diatom strain was between 2.6 and 18.6 % of total fatty acids, which were higher than in O. heteromucosa. Only A. coffeiformi possessed arachidonic acid. Oocystis heteromucosa naturally grew at high ammonium concentrations (1.4-10 mM), whereas the growth of the other strains, T. weissflogii and A. coffeiformi, were visibly inhibited at high ammonium concentrations (>1.4 mM-NH4). However, two strains of T. weissflogii were able to grow at up to 10 mM-NH4 by gradually acclimating to higher ammonium concentrations. The ammonium tolerant strains, especially T. weissflogii which have high EPA contents, were identified as a valuable candidate for biomass production utilizing NH4-N media, such as ammonium-rich wastewater.
Biomass and lipid production by the marine diatom Chaetoceros affinis were characterized under continuous light with aeration. Media based on palm oil mill effluent (POME; 10, 20 and 30 % v/v in distilled water) were used together with a standard control medium. The maximum biomass concentration on day 12 of batch cultures in control medium was 821 ± 71 mg L-1. Under identical conditions, in the best POME medium (20 % POME v/v in distilled water with other inorganic components), the biomass concentration was reduced by ∼11 % to 734 ± 66 mg L-1. The lipid content of the biomass grown in the control medium was 50.8 ± 4.5 % by dry weight, but was a little lower (48.9 ± 4.1 % by dry wt) in the above specified best POME medium. In the best POME medium, oleic acid was the major fatty acid (72.3 ± 5.2 % by weight) in the total lipids extracted from the biomass and monounsaturated fatty acids were the main type of fatty acids (74.6 ± 5.2 %). POME levels of >20 % in the medium suppressed both biomass and lipid production relative to the medium with 20 % POME.
Microalgae are a promising feedstock for carbon-neutral biofuel production due to their superior cellular composition. Alternatively, oxidative torrefaction has been recognized as a potential thermochemical technique for microalgal solid biofuel upgrading. Herein, by using microalga N. oceanica as a feedstock, several characterizations are adopted for evaluating the potential of oxidative torrefaction towards microalgal solid biofuel production. The oxidatively torrefied microalgae can be upgraded as lignite. After in-depth analysis, significant change in the surface microstructure of oxidatively torrefied microalgae is largely changed (via wrinkle and fragmentation) The hydrophobicity, thermal decomposition, thermal stability, and aromatization of oxidatively torrefied microalgae can be largely enhanced as the oxidative torrefaction severity increase. With the increasing torrefaction temperature, the hydrophobicity of oxidative torrefied microalgae gradually improved. The decomposition of C-2/3/5, and -OCH3, the CO bonds of CH3CO-, and the aromatization occurs via oxidative torrefaction according to the NMR analysis. For XPS analysis, torrefaction operation significantly decreases the carbide carbon and enhances the graphitization. As a result, the thermal stability of oxidatively torrefied microalgae is improved. Conclusively, the information obtained in this study can provide insights into the evaluation of oxidative torrefaction performance and fuel properties of microalgal solid biofuel, which may help accelerate the advancement of oxidative torrefaction industrialization.
Dehydroquinase or 3-dehydroquinate dehydratase (DHQD) reversibly cleaves 3-dehydroquinate to form 3-dehydroshikimate. Here, we describe the functional and structural features of a cold active type II 3-dehydroquinate dehydratase from the psychrophilic yeast, Glaciozyma antarctica PI12 (GaDHQD). Functional studies showed that the enzyme was active at low temperatures (10-30 °C), but displayed maximal activity at 40 °C. Yet the enzyme was stable over a wide range of temperatures (10-70 °C) and between pH 6.0-10.0 with an optimum pH of 8.0. Interestingly, the enzyme was highly thermo-tolerant, denaturing only at approximately 84 °C. Three-dimensional structure analyses showed that the G. antarctica dehydroquinase (GaDHQD) possesses psychrophilic features in comparison with its mesophilic and thermophilic counterparts such as higher numbers of non-polar residues on the surface, lower numbers of arginine and higher numbers of glycine-residues with lower numbers of hydrophobic interactions. On the other hand, GaDHQD shares some traits (i.e. total number of hydrogen bonds, number of proline residues and overall folding) with its mesophilic and thermophilic counterparts. Combined, these features contribute synergistically towards the enzyme's ability to function at both low and high temperatures.
The sustainability in polyhydroxyalkanoates (PHA) production is drawing increasing attention as the effort to increase the economic feasibility for commercialization pursues. Oleic acid is widely preferred by bacteria but its employment for PHA production makes sustainability rather dubious. This study showed promising poly(3-hydroxybutyrate-co-3-hydroxyvalerate) [P(3HB-co-3HV)] content of 68 wt % by lipase genes-harbouring Cupriavidus malaysiensis USMAA2-4 transformant from palm olein and 1-pentanol. High oleic acid content and low oil saturation caused palm olein to outperform crude palm oil, crude palm kernel oil and soybean oil due to its preference for oleic acid shown by previous screening. The transformant showed 8-fold and 40-fold higher lipase activity compared to C. necator H16 and its wild-type respectively. The transformant was unaffected by Co2+ but the growth of C. necator H16 was inversely proportional to Co2+ concentration and the employment of 1-pentanol also ceased its growth and PHA accumulation. Although the inhibitory effect of Fe2+, Cu2+ and Zn2+ at high molarity on LipA decreased PHA content of C. malaysiensis USMAA2-4 transformant by 23-24 wt %, the lipase activity was restorable with high molarity of Ca2+, thus resulted in higher PHA content. The transformant enabled the employment of low-cost 1-pentanol as the precursor for cost-effective PHA production and its preference for palm olein contributed to higher sustainability.
Biodiesel, as a renewable and eco-friendly energy source that can be produced through algae oil esterification, has recently received much attention. Maximization of algal biomass and lipid content is crucial for commercial biodiesel production. In this study, Chlorella sp. PG96, a microalgal strain isolated from urban wastewater, was identified considering its morphological and molecular characteristics. Fractional factorial design (211-7) was employed to screen medium and environmental factors for achieving high lipid productivity. The effects of eleven factors including light intensity, light spectrum, aeration rate, temperature, salinity, NaHCO3, CO2, NaNO3, NH4Cl, MgSO4.7H2O, and K2HPO4 and their interactions on growth characteristics of Chlorella sp. PG96 (biomass and lipid production) were statistically assessed. Based on the experimental results, lipid productivity was at its maximum (54.19 ± 8.40 mglipid L-1 day-1) under a combination of high levels of all factors. The analysis also showed that physical parameters of light intensity and temperature were more effective on algal growth compared to nutritional parameters. Furthermore, nitrogen source of ammonium and carbon source of bicarbonate played more significant roles in biomass and lipid production, compared with nitrate and CO2, respectively. Although the effect of sulfur limitation on cellular growth was similar to phosphorus deficiency, S-limitation had a greater impact on lipid accumulation. The interaction between NaHCO3 and NH4Cl was the most prominent interaction affecting all responses. It is concluded that Chlorella sp. PG96 at a high level of light intensity and temperature (22500 Lux and 32 °C, respectively) can be a prospective candidate for biodiesel production.
Co-culture of microalgae and microorganisms, supported with the resulting synergistic effects, can be used for wastewater treatment, biomass production, agricultural applications and etc. Therefore, this study aimed to explore the role of Bacillus subtilis (B. subtilis) in tolerance against the harsh environment of seafood wastewater, at which these microalgal-bacterial flocs were formed by microalgae cultivation. In this present study, B. subtilis isolated from the cultivation medium of Chlorella vulgaris and exposed to different salinity (0.1-4% w/v sodium chloride) and various pH range to determine the tolerant ability and biofilm formation. Interestingly, this bacteria strain that isolated from microalgae cultivation medium showed the intense viability in the salt concentration exceeding up to 4% (w/v) NaCl but demonstrated the decrease in cell division as environmental culture undergoing over pH 10. Cell viability was recorded higher than 71% and 92% for B. subtilis inoculum in media with salt concentration greater than 20 gL-1 and external pH 6.5-9, respectively. This showed that B. subtilis isolated from microalgal-bacteria cocultivation exhibited its tolerant ability to survive in the extremely harsh conditions and thus, mitigating the stresses due to salinity and pH.
Carboxylic acid reductases (CARs) are well-known for their eminent selective one-step synthesis of carboxylic acids to aldehydes. To date, however, few CARs have been identified and characterized, especially from fungal sources. In this study, the CAR from the white rot fungus Pycnoporus cinnabarinus (PcCAR2) was expressed in Escherichia coli. PcCAR2's biochemical properties were explored in vitro after purification, revealing a melting temperature of 53 °C, while the reaction temperature optimum was at 35 °C. In the tested buffers, the enzyme showed a pH optimum of 6.0 and notably, a similar activity up to pH 7.5. PcCAR2 was immobilized to explore its potential as a recyclable biocatalyst. PcCAR2 showed no critical loss of activity after six cycles, with an average conversion to benzaldehyde of more than 85% per cycle. Immobilization yield and efficiency were 82% and 76%, respectively, on Ni-sepharose. Overall, our findings contribute to the characterization of a thermotolerant fungal CAR, and established a more sustainable use of the valuable biocatalyst.
GR15 is a short molecule or peptide composed of aliphatic amino acids and possesses to have antioxidant properties. The GR15, 1GGGAFSGKDPTKVDR15 was identified from the protein S-adenosylmethionine synthase (SAMe) expressed during the sulfur departed state of Arthrospira platensis (spirulina or cyanobacteria). The in-silico assessment and the structural features of GR15 showed its antioxidant potency. Real-time PCR analysis found the up-regulation of ApSAMe expression on day 15 against oxidative stress due to 10 mM H2O2 treatment in A. platensis (Ap). The antioxidant activity of GR15 was accessed by the cell-free antioxidant assays such as ABTS, SARS, HRAS and NO; the results showed dose-dependent antioxidant activity. The toxicity assay was performed in both in vitro and in vivo models, in which peptide does not exhibit any toxicity in MDCK cell and zebrafish embryos. The intercellular ROS reduction potential of GR15 peptide was also investigated in both in vitro and in vivo models including LDH assay, antioxidant enzymes (SOD and CAT), and fluorescent staining assay (DCFDA, Hochest and Acridine orange sting) was performed; the results showed that the GR15 peptide was effectively reduced the ROS level. Further, RT-PCR demonstrated that GR15 enhanced the antioxidant property and also up-regulated the antioxidant gene, thus reduced the ROS level in both in vitro and in vivo models. Based on the results obtained from this study, we propose that GR15 has the potential antioxidant ability; hence further research can be directed towards the therapeutic product or drug development against disease caused by oxidative stress.
As the world's population grows, it is necessary to rethink how countries throughout the world produce food in order to replace the conventional and unsustainable agricultural techniques. Microalgae cultivation using a nutrient-rich solution from hydroponic systems not only presents a novel approach to solving problems pertaining to the impact of the discharges on the natural environment but also provides a plethora of other biotechnological applications particularly in the productions of high value-added products and plants growth stimulants, which can be potentially assimilated into the circular bioeconomy (CBE) in the hydroponic sector. In this review, the potential and practicability of microalgae to be merged into hydroponics CBE are reviewed. Overall, the integration of microalgal biorefineries in hydroponics systems can be realized after considering their Technology Readiness Level and System Readiness Level beforehand. Several suggestions on strains and hydroponics system improvement using existing biotechnological tools, Artificial Intelligence (AI) and nanobiotechnology in support of the CBE will be covered.
Biofuels from microalgae have promising potential for a sustainable bioeconomy. Algal strains' oil content and biomass yield are the most influential cost drivers in the fourth generation biofuel (FGB) production. Genetic modification is the key to improving oil accumulation and biomass yield, consequently developing the bioeconomy. This paper discusses current practices, new insights, and emerging trends in genetic modification and their bioeconomic impact on FGB production. It was demonstrated that enhancing the oil and biomass yield could significantly improve the probability of economic success and the net present value of the FGB production process. The techno-economic and socioeconomic burden of using genetically modified (GM) strains and the preventive control strategies on the bioeconomy of FGB production is reviewed. It is shown that the fully lined open raceway pond could cost up to 25% more than unlined ponds. The cost of a plastic hoop air-supported greenhouse covering cultivation ponds is estimated to be US 60,000$ /ha. The competitiveness and profitability of large-scale cultivation of GM biomass are significantly locked to techno-economic and socioeconomic drivers. Nonetheless, it necessitates further research and careful long-term follow-up studies to understand the mechanism that affects these parameters the most.
An emerging biofilm immobilization method has enabled effortless biomass harvesting and promoted economic feasibility. The current limitation towards the adaptation of this technology is the inadequate understanding of the biofilm interaction towards microporous membrane. Cell adhesion is recognized as the most important step towards the immobilized cultivation of microalgae. Cell attachment kinetic was studied in a short-term batch culture of three marine diatoms, Amphora coffeaeformis, Cylindrotheca fusiformis and Navicula incerta over 96 h on submerged commercial polyvinylidene fluoride (PVDF) membrane under swirling motion of culture medium. Both the evolution of cell adhesion intensity and compositional changes of the extracellular polymeric substances (EPS) released were quantified throughout the cultivation period. To delve into the cell-substratum interactions, existing thermodynamics and colloidal extended Derjaguin, Landau, Vervey, and Overbeek (XDLVO) theory were employed. As a result, A. coffeaeformis and N. incerta recorded a higher cell colonization percentage than C. fusiformis being the lowest about 2.16±0.17% cell colonization due to their respective species-dependent EPS variation. Polysaccharide contents were at least two times higher than protein contents for both C. fusiformis and N. incerta except for A. coffeaeformis depicting a lower polysaccharide-to-protein ratio whereby the protein contents were maximized at 1.03 × 103 ± 64.14 pg m-2 cell-1 at 6th h. From the surface free energy point of view, both thermodynamics and XDLVO model elucidated that cells adhered reversibly in the secondary energy minimum and ranked C. fusiformis the lowest adhesion tendency among three. These findings establish fundamental knowledge about biofilm formation in porous substrate bioreactors.
The issue of environmental pollution has been worsened by the emergence of new contaminants whose morphology is yet to be fully understood . Several techniques have been adopted to mitigate the pollution effects of these emerging contaminants, and bioremediation involving plants, microbes, or enzymes has stood out as a cost-effective and eco-friendly approach. Enzyme-mediated bioremediation is a very promising technology as it exhibits better pollutant degradation activity and generates less waste. However, this technology is subject to challenges like temperature, pH, and storage stability, in addition to recycling difficulty as it is arduous to isolate them from the reaction media. To address these challenges, the immobilization of enzymes has been successfully applied to ameliorate the activity, stability, and reusability of enzymes. Although this has significantly increased the uses of enzymes over a wide range of environmental conditions and facilitated the use of smaller bioreactors thereby saving cost, it still comes with additional costs for carriers and immobilization. Additionally, the existing immobilization methods have their individual limitations. This review provides state-of-the-art information to readers focusing on bioremediation using enzymes. Different parameters such as: the sustainability of biocatalysts, the ecotoxicological evaluation of transformation contaminants, and enzyme groups used were reviewed. The efficacy of free and immobilized enzymes, materials and methods for immobilization, bioreactors used, challenges to large-scale implementation, and future research needs were thoroughly discussed.
The attempt of this review article is to determine the impact of nuclear and mitochondrial damages on the propagation of cancer incidences. This review has advanced our understanding to altered genes and their relevant cancerous proteins. The progressive raising effects of free reactive oxygen species ROS and toxicogenic compounds contributed to significant mutation in nuclear and mitochondrial DNA where the incidence of gastric cancer is found to be linked with down regulation of some relevant genes and mutation in some important cellular proteins such as AMP-18 and CA-11. Thereby, the resulting changes in gene mutations induced the apparition of newly polymorphisms eventually leading to unusual cellular expression to mutant proteins. Reduction of these apoptotic growth factors and nuclear damages is increasingly accepted by cell reactivation effect, enhanced cellular signaling and DNA repairs. Acetylation, glycation, pegylation and phosphorylation are among the molecular techniques used in DNA repair for rectifying mutation incidences. In addition, the molecular labeling based fluorescent materials are currently used along with the bioconjugating of signal molecules in targeting disease translocation site, particularly cancers and tumors. These strategies would help in determining relevant compounds capable in overcoming problems of down regulating genes responsible for repair mechanisms. These issues of course need interplay of both proteomic and genomic studies often in combination of molecular engineering to cible the exact expressed gene relevant to these cancerous proteins.
Banana, a globally popular fruit, is widely cultivated in tropical and sub-tropical regions. After fruit harvest, remaining banana plant materials are low-value byproducts, mostly composted or used as fibre or for food packaging. As an aim to potentially increase farmer income, this study explored underutilised banana biomass as a novel plant tissue for production of a high-value product. Protein scFvTG130 used in this study, is an anti-toxoplasma single chain variable fragment antibody that can be used in diagnostics and neutralising the Toxoplasma gondii pathogen. Using detached banana leaves, we investigated the factors influencing the efficacy of a transient expression system using reporter genes and recombinant protein, scFvTG130. Transient expression was optimal at 2 days after detached banana leaves were vacuum infiltrated at 0.08 MPa vacuum pressure for a duration of 3 min with 0.01% (v/v) Tween20 using Agrobacterium strain GV3101 harbouring disarmed virus-based vector pIR-GFPscFvTG130. The highest concentration of anti-toxoplasma scFvTG130 antibody obtained using detached banana leaves was 22.8 µg/g fresh leaf tissue. This first study using detached banana leaf tissue for the transient expression of a recombinant protein, successfully demonstrated anti-toxoplasma scFvTG130 antibody expression, supporting the potential application for other related proteins using an underutilised detached banana leaf tissue.