Displaying publications 41 - 60 of 355 in total

Abstract:
Sort:
  1. Yap CJ, Lam SM, Sin JC, Zeng H, Li H, Huang L, et al.
    Environ Sci Pollut Res Int, 2023 Sep;30(42):96272-96289.
    PMID: 37566326 DOI: 10.1007/s11356-023-29165-6
    Attributable to the prosperous production growth of palm oil in Malaysia, the generated palm oil mill effluent (POME) poses a high threat owing to its highly polluted characteristic. Urged by the escalating concern of environmental conservation, POME pollution abatement and potential energy recovery from the effluent are flagged up as a research topic of interest. In this study, a cutting-edge photocatalytic fuel cell (PFC) system with employment of ZnO/Zn nanorod array (NRA) photoanode, CuO/Cu cathode, and persulfate (PS) oxidant was successfully designed to improve the treatment of POME and simultaneous energy production. The photoelectrodes were fabricated and characterized by field emission scanning electron microscopy with energy (FESEM), X-ray diffraction (XRD), energy-dispersive X-ray (EDX), and Brunauer, Emmett, and Teller analysis (BET). Owing to the properties of strong oxidant of PS, the proposed PFC/PS system has exhibited exceptional performance, attaining chemical oxygen demand (COD) removal efficiency of 96.2%, open circuit voltage (Voc) of 740.0 mV, short circuit current density (Jsc) of 146.7 μA cm-2, and power density (Pmax) of 35.6 μW cm-2. The pre-eminent PFC/PS system performance was yielded under optimal conditions of 2.5 mM of persulfate oxidant, POME dilution factor of 1:20, and natural solution pH of 8.51. Subsequently, the postulated photoelectrocatalytic POME treatment mechanism was elucidated by the radical scavenging study and Mott-Schottky (M-S) analysis. The following recycling test affirmed the stability and durability of the photoanode after four continuous repetition usages while the assessed electrical energy efficiency revealed the economic viability of PFC system serving as a post-treatment for abatement of POME. These findings contributed toward enhancing the sustainability criteria and economic viability of palm oil by adopting sustainable and efficient POME post-treatment technology.
    Matched MeSH terms: Electricity*
  2. Bien DC, Saman RM, Badaruddin SA, Lee HW
    Nanoscale Res Lett, 2011;6(1):543.
    PMID: 21970543 DOI: 10.1186/1556-276X-6-543
    We report on a process for fabricating self-aligned tungsten (W) nanowires with polycrystalline silicon core. Tungsten nanowires as thin as 10 nm were formed by utilizing polysilicon sidewall transfer technology followed by selective deposition of tungsten by chemical vapor deposition (CVD) using WF6 as the precursor. With selective CVD, the process is self-limiting whereby the tungsten formation is confined to the polysilicon regions; hence, the nanowires are formed without the need for lithography or for additional processing. The fabricated tungsten nanowires were observed to be perfectly aligned, showing 100% selectivity to polysilicon and can be made to be electrically isolated from one another. The electrical conductivity of the nanowires was characterized to determine the effect of its physical dimensions. The conductivity for the tungsten nanowires were found to be 40% higher when compared to doped polysilicon nanowires of similar dimensions.
    Matched MeSH terms: Electricity
  3. Panicker CY, Varghese HT, Nayak PS, Narayana B, Sarojini BK, Fun HK, et al.
    PMID: 25863456 DOI: 10.1016/j.saa.2015.03.065
    FT-IR spectrum of (2E)-3-(3-nitrophenyl)-1-[4-piperidin-1-yl]prop-2-en-1-one was recorded and analyzed. The vibrational wavenumbers were computed using HF and DFT quantum chemical calculations. The data obtained from wavenumber calculations are used to assign IR bands. Potential energy distribution was done using GAR2PED software. The geometrical parameters of the title compound are in agreement with the XRD results. NBO analysis, HOMO-LUMO, first and second hyperpolarizability and molecular electrostatic potential results are also reported. The possible electrophile attacking sites of the title molecule is identified using MEP surface plot study. Molecular docking results predicted the anti-leishmanic activity for the compound.
    Matched MeSH terms: Static Electricity
  4. Ng KH
    Med Lab Sci, 1991 Jul;48(3):189-92.
    PMID: 1787775
    Uniformity of electric field intensity of microwaves within the microwave oven cavity is necessary to ensure even load-heating, and is particularly important in pathology procedures where small volume irradiation is carried out. A simple and rapid method for mapping electric field distribution, using reversible thermographic paint, is described. Spatial heating patterns for various positions, and the effects of introducing dummy loads to modify heating distributions, have been obtained for a dedicated microwave processor, and comparison made with a domestic microwave oven.
    Matched MeSH terms: Electricity
  5. Silvarajoo S, Osman UM, Kamarudin KH, Razali MH, Yusoff HM, Bhat IUH, et al.
    Data Brief, 2020 Oct;32:106299.
    PMID: 32984485 DOI: 10.1016/j.dib.2020.106299
    One-pot synthetic method was adopted to prepare three isomers 4-(ortho-fluorophenyl)thiosemi- carbazide), 4-(meta-fluorophenyl)thiosemicarbazide and 4-(para-fluorophenyl)thiosemicarbazide. The products were obtained in ethanolic solution from a reaction between ortho, meta and para derivatives of fluorophenyl isothiocyanate and hydrazine hydrate. This work presents the theoretical Molecular Electrostatic Potential (MEP) and Highest Occupied Molecular Orbital-Lowest Unoccupied Molecular Orbital (HOMO-LUMO) computational data through Gaussview 5.0.9 and Gaussian09 software. Experimental Cole-cole plot for conductivity determination was also illustrated. The present data is important to manipulate the properties of compounds according to the position of a fluorine atom.
    Matched MeSH terms: Static Electricity
  6. Ho KC, Teoh YX, Teow YH, Mohammad AW
    J Environ Manage, 2021 Jan 01;277:111434.
    PMID: 33045646 DOI: 10.1016/j.jenvman.2020.111434
    This study assessed the environmental impacts of the formulation of graphene oxide (GO)/multi-walled carbon nanotubes (MWCNTs) conductive membranes and of the process operating parameters of electrically-enhanced palm oil mill effluent (POME) filtration. Two different analyses approaches were employed, cradle-to-gate approach for conductive membrane production and gate-to-gate approach for the POME filtration process. The parameters in conductive-membrane formulation (e.g. the weight ratio of carbon nanomaterials, and concentration of GO/MWCNT nanohybrids) and process operating parameters (e.g. electric field strength and electricity operating mode) were investigated. The findings herein are twofold. Firstly, for the fabrication of GO/MWCNT conductive membranes, the best weight ratio of GO:MWCNTs was found to be 1:9, given its superior membrane electrical conductivity with lower environmental impacts by 8.51% compared to pristine MWCNTs. The most suitable concentration of carbon nanomaterials was found to be 5 wt%, given its lowest impacts on resource depletion, human health, and ecosystems. Secondly, for the electrically-enhanced POME filtration, the optimum process operating parameters were found to be the application of an electric field of 300 V/cm in the continuous mode, given its lower environmental impacts (22.99%-89.30%) secondary to its requirement of the least electricity to produce permeate. The present study has established not only the optimized conditions in membrane formulation but also the operating parameters of electrically-enhanced filtration; such findings enable the use of cleaner production and sustainable approach to minimize fouling for industrial applications, whilst maintaining excellent efficiency.
    Matched MeSH terms: Electricity
  7. Sirunyan AM, Tumasyan A, Adam W, Ambrogi F, Asilar E, Bergauer T, et al.
    Phys Rev Lett, 2018 Dec 14;121(24):241802.
    PMID: 30608761 DOI: 10.1103/PhysRevLett.121.241802
    Three of the most significant measured deviations from standard model predictions, the enhanced decay rate for B→D^{(*)}τν, hints of lepton universality violation in B→K^{(*)}ℓℓ decays, and the anomalous magnetic moment of the muon, can be explained by the existence of leptoquarks (LQs) with large couplings to third-generation quarks and masses at the TeV scale. The existence of these states can be probed at the LHC in high energy proton-proton collisions. A novel search is presented for pair production of LQs coupled to a top quark and a muon using data at a center-of-mass energy of 13 TeV, corresponding to an integrated luminosity of 35.9  fb^{-1}, recorded by the CMS experiment. No deviation from the standard model prediction has been observed and scalar LQs decaying exclusively into tμ are excluded up to masses of 1420 GeV. The results of this search are combined with those from previous searches for LQ decays into tτ and bν, which excluded scalar LQs below masses of 900 and 1080 GeV. Vector LQs are excluded up to masses of 1190 GeV for all possible combinations of branching fractions to tμ, tτ and bν. With this analysis, all relevant couplings of LQs with an electric charge of -1/3 to third-generation quarks are probed for the first time.
    Matched MeSH terms: Electricity
  8. Md Razak Daud, Wan Nor Shela Ezwane Wan Jusoh, Syahrullail Samion
    MyJurnal
    This study investigates metal removal rate (MRR) of the biomaterial by using discharge machine Neuar CNC A50 Electrical Discharge Machine Die Sinking (EDM DS). The purpose of this study is to compare machining curvature cup for material SKD 11 and stainless steel with shape curvature cup acetabular. The result showed that electrode wear is higher when high current is applied. For each applied current 0.5A and 3.0A could result electrode wear of 0.236 mm, 0.246 mm and 0.269 mm respectively. Mean time of complete discharged for each pit with 0.3mm depth with supply 0. 5A is 6.51 minutes; 1. 5A is 3.54 minutes and 3A is 1.52 minutes. The biggest mean parameter of the pit is 0.356 mm, with 3A of current is applied. From this study, it can be concluded that low current set may give lower electrode copper wear. The experiment will help a researcher to discharge biomaterial types of metal with small size of copper electrode use of EDM DS Neuar for discharge multi hole or micro pit.
    Matched MeSH terms: Electricity
  9. Ismail Musirin, Titik Khawa Abdul Rahman
    Scientific Research Journal, 2006;3(1):11-25.
    MyJurnal
    Several incidents that occurred around the world involving power failure
    caused by unscheduled line outages were identified as one of the main
    contributors to power failure and cascading blackout in electric power
    environment. With the advancement of computer technologies, artificial
    intelligence (AI) has been widely accepted as one method that can be applied
    to predict the occurrence of unscheduled disturbance. This paper presents
    the development of automatic contingency analysis and ranking algorithm
    for the application in the Artificial Neural Network (ANN). The ANN is
    developed in order to predict the post-outage severity index from a set of preoutage
    data set. Data were generated using the newly developed automatic
    contingency analysis and ranking (ACAR) algorithm. Tests were conducted
    on the 24-bus IEEE Reliability Test Systems. Results showed that the developed
    technique is feasible to be implemented practically and an agreement was
    achieved in the results obtained from the tests. The developed ACAR can be
    utilised for further testing and implementation in other IEEE RTS test systems
    particularly in the system, which required fast computation time. On the other
    hand, the developed ANN can be used for predicting the post-outage severity
    index and hence system stability can be evaluated.
    Matched MeSH terms: Electricity
  10. Rehman GU, Tahir M, Goh PS, Ismail AF, Samavati A, Zulhairun AK, et al.
    Environ Pollut, 2019 Oct;253:1066-1078.
    PMID: 31434184 DOI: 10.1016/j.envpol.2019.07.013
    In this study, the synthesis of Fe3O4@GO@g-C3N4 ternary nanocomposite for enhanced photocatalytic degradation of phenol has been investigated. The surface modification of Fe3O4 was performed through layer-by-layer electrostatic deposition meanwhile the heterojunction structure of ternary nanocomposite was obtained through sonicated assisted hydrothermal method. The photocatalysts were characterized for their crystallinity, surface morphology, chemical functionalities, and band gap energy. The Fe3O4@GO@g-C3N4 ternary nanocomposite achieved phenol degradation of ∼97%, which was significantly higher than that of Fe3O4@GO (∼75%) and Fe3O4 (∼62%). The enhanced photoactivity was due to the efficient charge carrier separation and desired band structure. The photocatalytic performance was further enhanced with the addition of hydrogen peroxide, in which phenol degradation up to 100% was achieved in 2 h irradiation time. The findings revealed that operating parameters have significant influences on the photocatalytic activities. It was found that lower phenol concentration promoted higher activity. In this study, 0.3 g of Fe3O4@GO@g-C3N4 was found to be the optimized photocatalyst for phenol degradation. At the optimized condition, the reaction rate constant was reported as 6.96 × 10-3 min-1. The ternary photocatalyst showed excellent recyclability in three consecutive cycles, which confirmed the stability of this ternary nanocomposite for degradation applications.
    Matched MeSH terms: Static Electricity
  11. Yahaya Shagaiya Daniel, Zainal Abdul Aziz, Zuhaila Ismail, Faisal Salah
    MATEMATIKA, 2018;34(2):393-417.
    MyJurnal
    Analyzed the effects of thermal radiation, chemical reaction, heat gener-
    ation/absorption, magnetic and electric fields on unsteady flow and heat transfer of
    nanofluid. The transport equations used passively controlled. A similarity solution is
    employed to transformed the governing equations from partial differential equations to
    a set of ordinary differential equations, and then solve using Keller box method. It was
    found that the temperature is a decreasing function with the thermal stratification due to
    the fact the density of the fluid in the lower vicinity is much higher compared to the upper
    region, whereas the thermal radiation, viscous dissipation and heat generation enhanced
    the nanofluid temperature and thermal layer thickness.
    Matched MeSH terms: Electricity
  12. Shaifudin MS, Ghazali MSM, Kamaruzzaman WMIWM, Wan Abdullah WR, Kassim S, Ismail NQA, et al.
    Materials (Basel), 2021 Feb 03;14(4).
    PMID: 33546094 DOI: 10.3390/ma14040702
    This paper investigated the effects of Pr6O11 and Co3O4 on the electrical properties of ZnO-BaTiO3 varistor ceramics. The Pr6O11 doping has a notable influence on the characteristics of the nonlinear coefficient, varistor voltage, and leakage current where the values varied from 2.29 to 2.69, 12.36 to 68.36 V/mm and 599.33 to 548.16 µA/cm2, respectively. The nonlinear varistor coefficient of 5.50 to 7.15 and the varistor voltage of 7.38 to 8.10 V/mm was also influenced by the use of Co3O4 as a dopant. When the amount of Co3O4 was above 0.5 wt.%, the leakage current increased from 202.41 to 302.71 μA/cm2. The varistor ceramics with 1.5 wt.% Pr6O11 shows good nonlinear electrical performance at higher breakdown voltage and reduced the leakage current of the ceramic materials. Besides, the varistor sample that was doped with 0.5 wt.% Co3O4 was able to enhance the nonlinear electrical properties at low breakdown voltage with a smaller value of leakage current.
    Matched MeSH terms: Electricity
  13. Smallbone A, Hanipah MR, Jia B, Scott T, Heslop J, Towell B, et al.
    Energy Fuels, 2020 Oct 15;34(10):12926-12939.
    PMID: 33122874 DOI: 10.1021/acs.energyfuels.0c01647
    Free-piston engine generators (FPEGs) have huge potential to be the principal energy conversion device for generating electricity from fuel as part of a hybrid-electric vehicle (EV) powertrain system. The principal advantages lay in the fact that they are theoretically more efficient, more compact, and more lightweight compared to other competing EV hybrid and range-extender solutions (internal combustion engines, rotary engines, fuel cells, etc.). However, this potential has yet to be realized. This article details a novel dual-piston FPEG configuration and presents the full layout of a system and provides technical evidence of a commercial FPEG system's likely size and weight. The work also presents the first results obtained from a project which set-out to realize an operational FPEG system in hardware through the development and testing of a flexible prototype test platform. The work presents the performance and control system characteristics, for a first of a kind system; these show great technical potential with stable and repeatable combustion events achieved with around 700 W per cylinder and 26% indicated efficiency.
    Matched MeSH terms: Electricity
  14. Ong YP, Ho LN, Ong SA, Banjuraizah J, Ibrahim AH, Thor SH, et al.
    Chemosphere, 2021 Jan;263:128212.
    PMID: 33297171 DOI: 10.1016/j.chemosphere.2020.128212
    A unidirectional flow solar photocatalytic fuel cell (PFC) was successfully developed for the first time to offer alternative for electricity generation and simultaneous wastewater treatment. This study was focused on the synthesis of α-, δ- and β-MnO2 by wet chemical hydrothermal method for application as the cathodic catalyst in PFC. The crystallographic evolution was performed by varying the ratios of KMnO4 to MnSO4. The mechanism of the PFC with the MnO2/C as cathode was also discussed. Results showed that the catalytic activity of MnO2/C cathode was mainly predominated by their crystallographic structures which included Mn-O bond strength and tunnel size, following order of α- > δ- > β-MnO2/C. Interestingly, it was discovered that the specific surface areas (SBET) of different crystal phases did not give an impact on the PFC performance. However, the Pmax could be significantly influenced by the micropore surface area (Smicro) in the comparison among α-MnO2. Furthermore, the morphological transformation carried out by altering the hydrothermal duration demonstrated that the nanowire α-M3(24 h)/C with 1:1 ratio of KMnO4 and MnSO4 yielded excellent PFC performance with a Pmax of 2.8680 μW cm-2 and the lowest Rint of 700 Ω.
    Matched MeSH terms: Electricity
  15. Sharin Ab Ghani, Idris Mohd Yusoff
    MyJurnal
    As the lighting load constituted amount of power in electricity system, improving of efficiency in lighting technology would make a beneficial to consumer, energy provider and environment. Consequently, majority of home lighting manufacturers were competing each other by improving and claiming their product as the best energy efficient lighting product. Knowledge or exposure regarding to lighting technology especially on energy efficiency, power quality and economy are an important issues to give awareness to user before buy or use the lighting product. Therefore in this research study, three types of lighting product such as energy saving incandescent lighting, compact fluorescent lighting (CFL) and solid state lighting (LED) were compared. Comparative parameters were collected from data provided by lighting manufacturer and experimental data conducted in laboratory using power quality meter and lux meter. Hence, these study discussed in term of economy, power and light quality and energy efficiency of the tested lighting product. At the end of this study, the best home lighting technology is determined successfully.
    Matched MeSH terms: Electricity
  16. Khan R, Go Y
    Glob Chall, 2020 Feb;4(2):1900060.
    PMID: 32042443 DOI: 10.1002/gch2.201900060
    Malaysia targets to become the second-largest producer of solar photovoltaic (PV) in the world by increasing the current output from 12% to 20% in 2020. The government also expects to achieve 45% reduction of greenhouse gas emission by 2030 through renewable energy mainly by solar PV. Large-scale solar (LSS) aims to produce 2.5 GW, which contributes to 10% of the nation's electricity demands. The LSS system is held back by the grid-scale integration, transmission, and distribution infrastructure. Thus, power system analysis is crucial to achieve optimization in LSS to power grid integration. This paper investigates various power system analysis models and recommends an optimized configuration based on Malaysia's LSS scenario. In stage 1, an optimal PV sizing is carried out based on real data of LSS installation in different locations. In stage 2, power analysis is carried out using to analyze the potential difference variation when connected to a nine-bus power system. The potential variation at each bus of the system is assessed and hence provides a feasibility statement on the most effective configurations for LSS-grid integration. This paper serves as the reference model for LSS-grid integration in Malaysia and is expected to be replicated in the other countries with similar conditions.
    Matched MeSH terms: Electricity
  17. Tarusan SAA, Jidin A, Jamil MLM
    ISA Trans, 2021 Apr 16.
    PMID: 33931170 DOI: 10.1016/j.isatra.2021.04.005
    Direct Torque Control (DTC) scheme introduces a robust and simple control of electrical drive. However, its shortcomings such as broad torque ripple and variable switching frequency have offered several improvements like Space Vector Modulation (SVM) strategy, multilevel inverter (MLI) topology, etc. The conventional DTC which is fed by the two-level inverter has limited voltage vector, results in some difficulties to optimize the operation, especially at low operating speed. In contrast to MLI, the abundant of voltage vector has provided various amplitudes and angles that can overcome the problem of conventional DTC. Thus, this paper introduces the selected optimal voltage vector obtained from five-level Cascaded H-Bridge (CHB) inverter that employs in DTC hysteresis-based to achieve better optimization that similar to the DTC-SVM. Initially, the research work begins with an investigation on the performance comparison between a DTC hysteresis-based between two-level inverter (conventional method) and a five-level CHB inverter (proposed method). Here, a DC generator acted as a load is employed to control the operating speed instead of the speed controller (speed controller is negligible). Hence, the DTC method is optimized by minimizing the torque ripple as well as retaining the torque control capability at constant torque region on several operating speed. The selected optimal vector from the look-up table DTC of five-level CHB inverter must be dynamically appropriate to any change of torque (increased or decreased torque). For simplicity, this paper will only discuss the experimental results for both topologies of drive system. From the experimental results, it is verified that the torque ripples by the proposed method have achieved 10% and 50% reduction at high and low operating speed respectively. It is found that the DTC hysteresis-based result simpler control method than DTC-SVM while maintaining similar output performance.
    Matched MeSH terms: Electricity
  18. Lee CH, Khalina A, Lee SH
    Polymers (Basel), 2021 Jan 29;13(3).
    PMID: 33573036 DOI: 10.3390/polym13030438
    Plant fibers have become a highly sought-after material in the recent days as a result of raising environmental awareness and the realization of harmful effects imposed by synthetic fibers. Natural plant fibers have been widely used as fillers in fabricating plant-fibers-reinforced polymer composites. However, owing to the completely opposite nature of the plant fibers and polymer matrix, treatment is often required to enhance the compatibility between these two materials. Interfacial adhesion mechanisms are among the most influential yet seldom discussed factors that affect the physical, mechanical, and thermal properties of the plant-fibers-reinforced polymer composites. Therefore, this review paper expounds the importance of interfacial adhesion condition on the properties of plant-fiber-reinforced polymer composites. The advantages and disadvantages of natural plant fibers are discussed. Four important interface mechanism, namely interdiffusion, electrostatic adhesion, chemical adhesion, and mechanical interlocking are highlighted. In addition, quantifying and analysis techniques of interfacial adhesion condition is demonstrated. Lastly, the importance of interfacial adhesion condition on the performances of the plant fiber polymer composites performances is discussed. It can be seen that the physical and thermal properties as well as flexural strength of the composites are highly dependent on the interfacial adhesion condition.
    Matched MeSH terms: Static Electricity
  19. Abu Bakar H, Abd Rahim R, Soh PJ, Akkaraekthalin P
    Sensors (Basel), 2021 Jan 26;21(3).
    PMID: 33530534 DOI: 10.3390/s21030827
    Advances in reconfigurable liquid-based reconfigurable antennas are enabling new possibilities to fulfil the requirements of more advanced wireless communication systems. In this review, a comparative analysis of various state-of-the-art concepts and techniques for designing reconfigurable antennas using liquid is presented. First, the electrical properties of different liquids at room temperature commonly used in reconfigurable antennas are identified. This is followed by a discussion of various liquid actuation techniques in enabling high frequency reconfigurability. Next, the liquid-based reconfigurable antennas in literature used to achieve the different types of reconfiguration will be critically reviewed. These include frequency-, polarization-, radiation pattern-, and compound reconfigurability. The current concepts of liquid-based reconfigurable antennas can be classified broadly into three basic approaches: altering the physical (and electrical) dimensions of antennas using liquid; applying liquid-based sections as reactive loads; implementation of liquids as dielectric resonators. Each concept and their design approaches will be examined, outlining their benefits, limitations, and possible future improvements.
    Matched MeSH terms: Electricity
  20. Dey D, De D, Ahmadian A, Ghaemi F, Senu N
    Nanoscale Res Lett, 2021 Jan 29;16(1):20.
    PMID: 33512575 DOI: 10.1186/s11671-020-03467-x
    Doping is the key feature in semiconductor device fabrication. Many strategies have been discovered for controlling doping in the area of semiconductor physics during the past few decades. Electrical doping is a promising strategy that is used for effective tuning of the charge populations, electronic properties, and transmission properties. This doping process reduces the risk of high temperature, contamination of foreign particles. Significant experimental and theoretical efforts are demonstrated to study the characteristics of electrical doping during the past few decades. In this article, we first briefly review the historical roadmap of electrical doping. Secondly, we will discuss electrical doping at the molecular level. Thus, we will review some experimental works at the molecular level along with we review a variety of research works that are performed based on electrical doping. Then we figure out importance of electrical doping and its importance. Furthermore, we describe the methods of electrical doping. Finally, we conclude with a brief comparative study between electrical and conventional doping methods.
    Matched MeSH terms: Electricity
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links