Engineered cementitious composite (ECC) was discovered as a new substitute of conventional concrete as it provides better results in terms of tensile strain, reaching beyond 3%. From then, more studies were done to partially replace crumb rubber with sand to achieve a more sustainable and eco-friendlier composite from the original ECC. However, the elastic modulus of ECC was noticeably degraded. This could bring potential unseen dangerous consequences as the fatigue might happen at any time without any sign. The replacement of crumb rubber was then found to not only bring a more sustainable and eco-friendlier result but also increase the ductility and the durability of the composite, with lighter specific gravity compared to conventional concrete. This study investigated the effects of crumb rubber (CR) and graphene oxide (GO) toward the deformable properties of rubberized ECC, including the compressive strength, elastic modulus, Poisson's ratio, and drying shrinkage. Central composite design (CCD) was utilized to provide 13 reasonable trial mixtures with the ranging level of CR replacement from 0-30% and that of GO from 0.01-0.08%. The results show that GO increased the strength of the developed GO-RECC. It was also found that the addition of CR and GO to ECC brought a notable improvement in mechanical and deformable properties. The predicted model that was developed using response surface methodology (RSM) shows that the variables (compression strength, elastic modulus, Poisson's ratio, and drying shrinkage) rely on the independent (CR and GO) variables and are highly correlated.
In recent days, there is an increasing use of green composites in composite manufacturing, where cellulosic natural fibers have been started using for this purpose. In line with this, a novel cellulose fiber was extracted from the Kigelia africana fruit and its physical, chemical and thermal properties, crystallography and surface morphology analysis were studied and reported in this investigative research paper. The physical analysis revealed the mean tensile strength as 50.31 ± 24.71 to 73.12 ± 32.48 MPa, diameter as 0.507 ± 0.162 to 0.629 ± 0.182 mm and density as 1.316 g/cm³ for the Kigelia africana fiber. The proximate chemical analysis estimated the cellulose percentage to be 61.5 % and the existence of different basic components like cellulose, hemicellulose and lignin are confirmed by Fourier transform infrared spectroscopy analysis. Thermogravimetric analysis establishes the thermal stability of the fiber as 212 ⁰C. The crystallinity index, 57.38 % of the fiber was determined by X-ray diffraction. Surface morphology by field emission scanning electron microscopy reveals the presence of protrusions in fiber which aid in the better adhesion with the matrix in composite manufacturing.
The objective of this study was to evaluate the effects of milling methods on tensile properties of polypropylene (PP) / oil palm mesocarp fibre (OPMF) biocomposites. Two types of mills were used; Wiley mill (WM) and disc mill (DM). Ground OPMF from each milling process was examined for its particle size distribution and aspect ratio by sieve and microscopic analyses, respectively. Results showed that DM-OPMF had smaller diameter fibre with uniform particle size compared to the WM-OPMF. Surface morphology study by SEM showed that DM-OPMF had rougher surface compared to WM-OPMF. Furthermore, it was found that PP/DM-OPMF biocomposite had higher tensile strength compared to PP/WM-OPMF, with almost two-fold. Thus, it is suggested that small diameter and uniform size fibre may improve stress transfer and surface contact between the fibre and polymer matrix and cause well dispersion of filler throughout the polymer resulted in better tensile strength of PP/DM-OPMF Compared to PP/WM-OPMF biocomposite. Overall, it can be concluded that disc milling could serve as a simple and effective grinding method for improving the tensile properties of biocomposite.
Evaluation of the mechanical behaviour of restoration dental materials is essential to understand their performance under different load conditions and to estimate their durability under clinical oral function. Restorative materials and dental tissues like other materials by having specific mechanical properties, such as static strength (i.e. compressive strength, tensile strength, flexural strength) and dynamic strength (i.e. fatigue strength). The selection of proper mechanical test type depends on the goals that the study claims to define. On such basis, the mechanical test can be chosen correctly. Laboratory studies should be designed as replications of the clinical oral circumstances to measure the mechanical and physical properties of a material and any arbitrary choices in the design of the study may result in large variations of data.
This paper details a study conducted to evaluate the performance of cold in-place recycling (CIPR) using polymer modified asphalt emulsion (PMAE). The asphalt emulsion was modified using natural rubber latex (NRL). Four proportions of reclaimed asphalt pavement (RAP) which are 0%, 25%, 50% and 75% were mixed with natural aggregates and modified asphalt emulsion using natural rubber latex (NRL). The results showed that the optimum modified asphalt emulsion for each proportion of RAP decreased due to the increase in RAP content. Results obtained from Indirect Tensile Strength (ITS) and Uniaxial Compressive Strength (UCS) test for the mixes complied with the requirements of the Road Engineering Association of Malaysia (REAM) specifications. The unsoaked and soaked ITS values obtained were 0.2 MPa and 0.15 MPa respectively, and the minimum compressive strength of CIPR mix obtained was 0.7 MPa. Based on the evaluation of performance for the four RAP proportions, it was determined that 50% of RAP gave the best combination of the CIPR mixture.
This paper presents a study on the effect of Arenga Pinnata fibre volume fraction on the tensile and compressive properties of Arenga Pinnata fibre reinforced epoxy composite (APREC). The composites were produced using four different Arenga Pinnata fibre volume contents, which were 10vol%, 15vol%, 20vol%, and 25vol%, in unidirectional (UD) fibre alignment. Tensile and compression tests were performed on all APREC specimens in order to investigate the effect of fibre volume fraction on modulus of elasticity, strength and strain to failure. The morphological structure of fractured specimens was observed using scanning electron microscopy (SEM) in order to evaluate the fracture mechanisms involved when the specimens were subjected to tensile or compressive loading. The results indicated that the higher the amount of Arenga Pinnata fibres, the higher the stiffness of the composites. This is shown by the increment of tensile and compressive modulus of the specimens when the fibre volume content was increased. Tensile modulus increased up to 180% when 25vol% Arenga Pinnata fibre was used in APREC compared to Pure Epoxy specimen. It can also be observed that the tensile strength of the specimens increased 28% from 53.820 MPa (for Pure Epoxy) to 68.692 MPa (for Epoxy with 25vol% APREC addition). Meanwhile, compressive modulus and strength increased up to 3.24% and 9.17%, respectively. These results suggest that the addition of Arenga Pinnata fibres significantly improved the tensile and compressive properties of APREC.
The purpose of this study is to compare the tensile strength between additional polystyrene into coconut meat husk reinforced fiber composite. Composite were produced by using hand layup technique. It is seen that with the additional of polystyrene into the coconut meat husk reinforced polyester composites showed the increment tensile strength value compared to the non-added polystyrene which indicates that effective stress transfer between the fiber, matrix and polystyrene.
Peroxide pre-vulcanized natural rubber latex prepared by using gamma irradiation technique is an alternative over the conventionally prepared peroxide pre-vulcanized that used activator to promote the peroxide decomposition in natural rubber latex. Through this technique the problems aroused by some activators such as tends to darken the natural rubber latex film during the drying process can also be overcome. For this preliminary study, data obtained from crosslink density and mechanical measurements were used to evaluate the effectiveness of gamma irradiation in the vulcanization process. Increasing the quantity of tert-butyl hydroperoxide (t-BHPO) from 0.1 pphr to 0.3 pphr while the irradiation dose maintain at 12 kGy has successfully delivered peroxide vulcanized natural rubber latex films with average tensile strength, modulus @ 500% and modulus @ 700% around 15.33, 1.01 and 3.42 MPa, respectively. The effective pre-vulcanization irradiation dose with respect to maximum crosslinking density (85.8 %) was observed on film prepared at 0.1 pphr t-BHPO.
Radiation pre-vulcanised natural rubber latex (RVNRL) prepared by using gamma irradiation technique has many advantages over the conventionally prepared sulphur pre-vulcanised natural rubber latex (SPVL). Despite the fact that many potential latex dipped products can be made from RVNRL, little effort was made to fully commercialise the products because of the inferior strength of RVNRL products compared to SPVL products. An attempt was made to improve the tensile strength of RVNRL by combining both radiation and peroxide vulcanisation in order to ensure that the products will not tear or fail, and has sufficient stretch. Hexanediol diacrylate (HDDA) plays the main role as sensitizer during radiation vulcanisation and tert-butyl hydroperoxide (t-BHPO) as the co-sensitizer in peroxide vulcanisation. Pre-vulcanised natural rubber latex dipped films via hybrid radiation and peroxidation vulcanisations obtained showed tensile strength of 26.7 MPa, an increment of more than 15% compared to controlled film (22.5 MPa). Besides, the crosslink percentage of the rubber films also showed around 5% increment from 90.7% to 95.6%.
To date, the mechanical performance of kenaf composites is still unsatisfied in term of its mechanical performance. Therefore, research focuses on kenaf composites fabrication through the selection of polymer resin, including epoxy, polypropylene, and polylactic acid. The incorporated kenaf fibre at 10 wt % to 40 wt % loadings was conducted using injection and a compression moulding process. The compressed materials indicated high tensile strength at 240 MPa compared to inject materials (60 MPa). Significant improvement on impact strength (9 kJ/m2) was due to the unpulled-out fibre that dispersed homogenously and hence minimize the microcrack acquire. Meanwhile, high flexural strength (180 MPa) obtained by kenaf/epoxy composites due to the fibre orientate perpendicular to the loading directions, which improve its mechanical properties. The findings indicate that the kenaf fibre reinforced thermoset materials exhibit better mechanical properties as a function to the battery tray applications.
Several methods of incorporating sago pith waste (SPW) into poly(vinyl alcohol) (PVA) had been conducted: (i) dry blending (PVA/SPW/G), (ii) blending of SPW and pre-plasticized PVA (pPVA/SPW/G) and (iii) blending of pre-plasticized of both PVA and SPW (pPVA/pSPW). The effect of the compounding method on the mechanical and water absorption properties were investigated. The addition of SPW into PVA greatly reduced the tensile strength and elongation at break. The tensile strength and elongation at break of PVA/SPW composites with identical geometry during compounding stage (powder/powder and pellet/pellet), which were PVA/SPW/G and pPVA/pSPW yielded the highest value. The percentage of water absorbed by PVA/SPW/G (without pre-plasticization) was the highest, followed by pPVA/pSPW and pPVA/SPW/G.
Hybrid composites of polypropylene (PP)/nanoclay (NC)/glass fiber (GF) were prepared byextrusion and injection molding. Molded specimens were analyzed by transmission electron microscopy (TEM), thermogravimetric analysis (TGA), tensile and flexural tests. TEM results revealed NC particle intercalation. TGA results showed that the incorporation of clay into the GF composite improves the thermal stability of the material. The initial thermal decomposition temperatures also shifted to higher values. Incorporation of GF into PP lowers the tensile strength of the binary composite, indicating poor fiber-matrix interfacial adhesion. However, introducing NC increased the strength of the ternary composites. Tensile modulus was enhanced with the incorporation of GF and further increased with an introduction of NC. Flexural strength and flexural modulus are both enhanced with an increase in GF and NC loading.
The tensile strength of intact rock materials has been determined by indirect method more frequent than the direct method.
The most commonly used indirect method is Brazilian test. Stress and deformability undergo during the test reflected by
geometry shape of the samples with respect to the different diameter ratio. This study focuses on influence of geometry
shape in solid and ring disk with different diameter ratio on the stress distribution and deformations within sandstone
subjected to indirect tensile loading by Brazilian test. Then, the finite element method in RS2 software was utilised to
simulate and gain in depth understanding the behaviour of Brazilian test. The analysis shown that the maximum tensile
strength in a ring disk with diameter ratio of 0.1 is three times higher than in solid disk. Meanwhile, as the diameter
ratio of ring disk increases, it produces lower tensile strength. The numerical simulation also has successfully illustrated
the shear failure which observed near the loading platen of solid disk during Brazilian test. The finite element analysis
utilised in this research has successfully enables the stress distribution and deformation behaviour of the rock under
tension to be studied closely
This study aims to investigate the void content, tensile, vibration and acoustic properties of kenaf/bamboo fiber reinforced epoxy hybrid composites. The composites were made using the hand lay-up method. The weight ratios of kenaf/bamboo were 30:70, 50:50 and 70:30. Further, kenaf and bamboo composites were fabricated for the purpose of comparison. The hybridization of woven kenaf/bamboo reduced the void content. The void contents of hybrid composites were almost similar. An enhancement in elongation at break, tensile strength and modulus of hybrid composites was observed until a kenaf/bamboo ratio of 50:50. Kenaf/bamboo (50:50) hybrid composite displays the highest elongation at break, tensile strength and modulus compared to the other hybrid composites which are 2.42 mm, 55.18 MPa and 5.15 GPa, respectively. On the other hand, the highest natural frequency and damping factors were observed for Bamboo/Kenaf (30:70) hybrid composites. The sound absorption coefficient of composites were measured in two conditions: without air gap and with air gap (10, 20, 30 mm). The sound absorption coefficient for testing without air gap was less than 0.5. Introducing an air gap improved the sound absorption coefficient of all composites. Hence, hybrid kenaf/bamboo composites exhibited less void content, as well as improved tensile, vibration and acoustic properties.
This research was carried out to study the effects of kenaf loading and alkaline treatment on tensile properties, density,
thermal and morphological properties of kenaf filled natural rubber latex foam (NRLF). Samples were prepared using a
Dunlop method. From the results, increasing loading of kenaf reduced the tensile strength and elongation at break for
both samples, treated and untreated kenaf filled NRLF. Meanwhile, modulus at 100% elongation and density increased
with an increased in kenaf loading. Samples with treated kenaf showed higher tensile strength, modulus at 100%
elongation and density but low in elongation at break as compared with samples with untreated kenaf. Thermal study
by using thermogravimetric analysis (TGA) showed that thermal stability reduced with increased in kenaf loading for
both samples. Samples with treated kenaf have higher thermal stability compared with samples of untreated kenaf. The
filler-matrix interaction and the pores size variation of both samples was clearly seen in the micrograph images by using
scanning electron microscope (SEM).
The objective of this work was to develop a plastic film from food sources with excellent thermal, mechanical, and degradability performance. Corn starch (CS)/nata de coco (NDC) were hybridized with addition of glycerin as plasticizer at different weight ratio and weight percent, respectively. Sample analysis found that the hybridization of CS with NDC improved the film forming properties, mechanical and thermal, degradation properties, as well as hydrophobicity and solubility of the film up to 0.5:0.5 wt hybrid ratio. The properties of the films were highly affected by the homogeneity of the sample during hybridization, with high NDC amount (0.3:0.7 wt CS:NDC) showing poor hydrophobicity, and mechanical and thermal properties. The glycerin content, however, did not significantly affect the hydrophobicity, water solubility, and degradability properties of CS/NDC film. Hybridization of 0.5:0.5 wt CS/NDC with 2 phr glycerin provided the optimum Young's modulus (15.67 MPa) and tensile strength (1.67 MPa) properties.
A nanocomposite containing polypropylene (PP) and nano α-Al2O3 particles was prepared using a Haake internal mixer. Mechanical tests, such as tensile and flexural tests, showed that mechanical properties of the composite were enhanced by addition of nano α-Al2O3 particles and dispersant agent to the polymer. Tensile strength was approximately ∼ 16% higher than pure PP by increasing the nano α-Al2O3 loading from 1 to 4 wt% into the PP matrix. The results of flexural analysis indicated that the maximum values of flexural strength and flexural modulus for nanocomposite without dispersant were 50.5 and 1954 MPa and for nanocomposite with dispersant were 55.88 MPa and 2818 MPa, respectively. However, higher concentration of nano α-Al2O3 loading resulted in reduction of those mechanical properties that could be due to agglomeration of nano α-Al2O3 particles. Transmission and scanning electron microscopic observations of the nanocomposites also showed that fracture surface became rougher by increasing the content of filler loading from 1 to 4% wt.
A new class of biocomposites based on oil palm empty fruit bunch fiber and poly(butylene adipate-co-terephthalate) (PBAT), which is a biodegradable aliphatic aromatic co-polyester, were prepared using melt blending technique. The composites were prepared at various fiber contents of 10, 20, 30, 40 and 50 wt% and characterized. Chemical treatment of oil palm empty fruit bunch (EFB) fiber was successfully done by grafting succinic anhydride (SAH) onto the EFB fiber surface, and the modified fibers were obtained in two levels of grafting (low and high weight percentage gain, WPG) after 5 and 6 h of grafting. The FTIR characterization showed evidence of successful fiber esterification. The results showed that 40 wt% of fiber loading improved the tensile properties of the biocomposite. The effects of EFB fiber chemical treatments and various organic initiators content on mechanical and thermal properties and water absorption of PBAT/EFB 60/40 wt% biocomposites were also examined. The SAH-g-EFB fiber at low WPG in presence of 1 wt% of dicumyl peroxide (DCP) initiator was found to significantly enhance the tensile and flexural properties as well as water resistance of biocomposite (up to 24%) compared with those of untreated fiber reinforced composites. The thermal behavior of the composites was evaluated from thermogravimetric analysis (TGA)/differential thermogravimetric (DTG) thermograms. It was observed that, the chemical treatment has marginally improved the biocomposites' thermal stability in presence of 1 wt% of dicumyl peroxide at the low WPG level of grafting. The improved fiber-matrix surface enhancement in the chemically treated biocomposite was confirmed by SEM analysis of the tensile fractured specimens.
The development and characterization of environmentally friendly bilayer films from sugar palm starch (SPS) and poly(lactic acid) (PLA) were conducted in this study. The SPS-PLA bilayer films and their individual components were characterized for their physical, mechanical, thermal and water barrier properties. Addition of 50% PLA layer onto 50% SPS layer (SPS50-PLA50) increased the tensile strength of neat SPS film from 7.74 to 13.65MPa but reduced their elongation at break from 46.66 to 15.53%. The incorporation of PLA layer significantly reduced the water vapor permeability as well as the water uptake and solubility of bilayer films which was attributed to the hydrophobic characteristic of the PLA layer. Furthermore, scanning electron microscopy (SEM) image of SPS50-PLA50 revealed lack of strong interfacial adhesion between the SPS and PLA. Overall, the incorporation of PLA layer onto SPS films enhances the suitability of SPS based films for food packaging.
The aim of this work is to study the behavior of biodegradable sugar palm starch (SPS) based thermoplastic containing agar in the range of 10-40wt%. The thermoplastics were melt-mixed and then hot pressed at 140°C for 10min. SEM investigation showed good miscibility between SPS and agar. FT-IR analysis confirmed that SPS and agar were compatible and inter-molecular hydrogen bonds existed between them. Incorporation of agar increased the thermoplastic starch tensile properties (Young's modulus and tensile strength). The thermal stability and moisture uptake increased with increasing agar content. The present work shows that starch-based thermoplastics with 30wt% agar content have the highest tensile strength. Higher content of agar (40wt%) resulted to more rough cleavage fracture and slight decrease in the tensile strength. In conclusion, the addition of agar improved the thermal and tensile properties of thermoplastic SPS which widened the potential application of this eco-friendly material. The most promising applications for this eco-friendly material are short-life products such as packaging, container, tray, etc.