MyMedR

Displaying publications 61 - 80 of 191 in total

Abstract:

Sort:

Fabrication and performance evaluation of blood compatible hemodialysis membrane using carboxylic multiwall carbon nanotubes and low molecular weight polyvinylpyrrolidone based nanocomposites

Irfan M, Irfan M, Idris A, Baig N, Saleh TA, Nasiri R, et al.

J Biomed Mater Res A, 2019 03;107(3):513-525.
PMID: 30484939 DOI: 10.1002/jbm.a.36566

This study focused to optimize the performance of polyethersulfone (PES) hemodialysis (HD) membrane using carboxylic functionalized multiwall carbon nanotubes (c-MWCNT) and lower molecular weight grade of polyvinylpyrrolidone (PVP-k30). Initially, MWCNT were chemically functionalized by acid treatment and nanocomposites (NCs) of PVP-k30 and c-MWCNT were formed and subsequently blended with PES polymer. The spectra of FTIR of the HD membranes revealed that NCs has strong hydrogen bonding and their addition to PES polymer improved the capillary system of membranes as confirmed by Field Emission Scanning Electron Microscope (FESEM) and leaching of the additive decreased to 2% and hydrophilicity improved to 22%. The pore size and porosity of NCs were also enhanced and rejection rate was achieved in the establish dialysis range (<60 kDa). The antifouling studies had shown that NCs membrane exhibited 30% less adhesion of protein with 80% flux recovery ratio. The blood compatibility assessment disclosed that NCs based membranes showed prolonged thrombin and prothrombin clotting times, lessened production of fibrinogen cluster, and greatly suppressed adhesion of blood plasma than a pristine PES membrane. The results also unveiled that PVP-k30/NCs improved the surface properties of the membrane and the urea and creatinine removal increased to 72% and 75% than pure PES membranes. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 107A: 513-525, 2019.

Matched MeSH terms: Nanotubes, Carbon/chemistry*
Fulltext Investigating the effectiveness of nanotechnologies in environmental health with an emphasis on environmental health journals

Aghalari Z, Dahms HU, Sillanpää M

Life Sci Soc Policy, 2021 Sep 13;17(1):8.
PMID: 34511108 DOI: 10.1186/s40504-021-00116-8

OBJECTIVE: The use of nanotechnologies is important to reduce environmental health problems in Iran, so the present study was conducted to determine the effectiveness of nanotechnologies in environmental health. This is a cross-sectional descriptive study for 11-year periods (2008-2018) on all articles published in three specialized journals of environmental health with emphasis on the use of nanotechnologies in various fields of environmental health (water, air, sewage, waste, food, radiation, etc).
RESULTS: In this study, 774 articles related to 114 issues of 3 specialized environmental health journals were reviewed. A review of 774 articles showed that 80 articles (10.3%) were published in the field of nanotechnologies. Out of 80 articles published in the field of nanotechnology, 66 articles (82.5%) were published on the subject of water, 9 articles (11.3%) on wastewater and 5 articles (6.2%) on air pollution. Subject review of articles showed that articles using carbon nanotubes to remove natural organic pollutants, surfactants, hydroxybenzenes, phenol, dimethyl phthalates, use of titanium dioxide nanoparticles, iron-magnesium nanoparticles for wastewater treatment, Silver nanoparticles were used to remove air pollution. The results showed that published articles on nanotechnology in the field of environmental health were few.

Matched MeSH terms: Nanotubes, Carbon*
Box-Behnken design optimisation of a green novel nanobio-based reagent for rapid visualisation of latent fingerprints on wet, non-porous substrates

Azman AR, Mahat NA, Wahab RA, Ahmad WA, Puspanadan JK, Huri MAM, et al.

Biotechnol Lett, 2021 Apr;43(4):881-898.
PMID: 33389272 DOI: 10.1007/s10529-020-03052-3

OBJECTIVE: Optimisation of the green novel nanobio-based reagent (NBR) for rapid visualisation of groomed fingerprints on wet non-porous substrates using response surface methodology and assessment of its stability and sensitivity were attempted for forensic applications.
RESULTS: Scanning electron microscopy images demonstrated successful attachments of NBR onto the constituents of fingerprints on the substrates. The highest average quality of visualised fingerprints was attained at the optimum condition (100 mg of CRL; 75 mg of acid-functionalised multi-walled carbon nanotubes; 5 h of immobilisation). The NBR produced comparable average quality of fingerprints with the commercially available small particle reagent, even after 4 weeks of storage (without any preservatives) in both chilled and sultry conditions. The NBR was sensitive enough to visualise the increasingly weaker fingerprints, particularly on glass slides.
CONCLUSION: The optimised novel NBR could be the relatively greener option for visualising latent fingerprints on wet, non-porous substrates for forensic applications.

Matched MeSH terms: Nanotubes, Carbon/chemistry*
Fulltext Experimental and theoretical investigation of sensing parameters in carbon nanotube-based DNA sensor

Nouri M, Meshginqalam B, Sahihazar MM, Sheydaie Pour Dizaji R, Ahmadi MT, Ismail R

IET Nanobiotechnol, 2018 Dec;12(8):1125-1129.
PMID: 30964025 DOI: 10.1049/iet-nbt.2018.5068

Nowadays, sensitive biosensors with high selectivity, lower costs and short response time are required for detection of DNA. The most preferred materials in DNA sensor designing are nanomaterials such as carbon and Au nanoparticles, because of their very high surface area and biocompatibility which lead to performance and sensitivity improvements in DNA sensors. Carbon nanomaterials such as carbon nanotubes (CNTs) can be considered as a suitable DNA sensor platform due to their high surface-to-volume ratio, favourable electronic properties and fast electron transfer rate. Therefore, in this study, the CNTs which are synthesised by pulsed AC arc discharge method on a high-density polyethylene substrate are used as conducting channels in a chemiresistor for the electrochemical detection of double stranded DNA. Moreover, the response of the proposed sensor is investigated experimentally and analytically in different temperatures, which confirm good agreement between the presented model and experimental data.

Matched MeSH terms: Nanotubes, Carbon/chemistry*
Fulltext Analytical modeling of trilayer graphene nanoribbon Schottky-barrier FET for high-speed switching applications

Rahmani M, Ahmadi MT, Abadi HK, Saeidmanesh M, Akbari E, Ismail R

Nanoscale Res Lett, 2013;8(1):55.
PMID: 23363692 DOI: 10.1186/1556-276X-8-55

Recent development of trilayer graphene nanoribbon Schottky-barrier field-effect transistors (FETs) will be governed by transistor electrostatics and quantum effects that impose scaling limits like those of Si metal-oxide-semiconductor field-effect transistors. The current-voltage characteristic of a Schottky-barrier FET has been studied as a function of physical parameters such as effective mass, graphene nanoribbon length, gate insulator thickness, and electrical parameters such as Schottky barrier height and applied bias voltage. In this paper, the scaling behaviors of a Schottky-barrier FET using trilayer graphene nanoribbon are studied and analytically modeled. A novel analytical method is also presented for describing a switch in a Schottky-contact double-gate trilayer graphene nanoribbon FET. In the proposed model, different stacking arrangements of trilayer graphene nanoribbon are assumed as metal and semiconductor contacts to form a Schottky transistor. Based on this assumption, an analytical model and numerical solution of the junction current-voltage are presented in which the applied bias voltage and channel length dependence characteristics are highlighted. The model is then compared with other types of transistors. The developed model can assist in comprehending experiments involving graphene nanoribbon Schottky-barrier FETs. It is demonstrated that the proposed structure exhibits negligible short-channel effects, an improved on-current, realistic threshold voltage, and opposite subthreshold slope and meets the International Technology Roadmap for Semiconductors near-term guidelines. Finally, the results showed that there is a fast transient between on-off states. In other words, the suggested model can be used as a high-speed switch where the value of subthreshold slope is small and thus leads to less power consumption.

Matched MeSH terms: Nanotubes, Carbon
Nanoscaled Surface Modification of Poly(dimethylsiloxane) Using Carbon Nanotubes for Enhanced Oil and Organic Solvent Absorption

Ong CC, Sundera Murthe S, Mohamed NM, Perumal V, Mohamed Saheed MS

ACS Omega, 2018 Nov 30;3(11):15907-15915.
PMID: 31458235 DOI: 10.1021/acsomega.8b01566

This article demonstrates a novel nanoscale surface modification method to enhance the selectivity of porous poly(dimethylsiloxane) (PDMS) in removing oil from water. The surface modification method is simple and low cost by using sugar as a sacrificial template for temporal adhering of carbon nanotubes (CNT) before addition of PDMS prepolymer to encapsulate the CNT on its surface once polymerized. The PDMS-CNT demonstrated a tremendous increase in absorption capacity up to 3-fold compared to previously reported absorbents composed solely of PDMS. Besides showcasing excellent absorption capacity, the PDMS-CNT also shows a faster absorption rate (25 s) as compared to that of pure PDMS (40 s). The enhanced absorption rate is due to the incorporation of CNT, which roughens the surface of the polymer at the nanoscale and lowers the surface energy of porous PDMS while at the same time increasing the absorbent hydrophobicity and oleophilicity. This property makes the absorbent unique in absorbing only oil but repelling water at the same time. The PDMS-CNT is an excellent absorbent material with outstanding recyclability and selectivity for removing oil from water.

Matched MeSH terms: Nanotubes, Carbon
Fulltext PMMA doped Multi Walled Carbon Nanotube (MWCNTs) microfiber for alcohol sensing application

Husna Abdul Rahman, Haliza M. Haron, Naimah Mat Isa, Hasnida Saad

ESTEEM Academic Journal, 2020;15(2):24-34.
MyJurnal

PMMA polymer microfiber doped Multi Walled Carbon Nanotubes (MWCNTs) was reported for alcohol sensing application. The sensitivity of the sensor is increasing relatively with the increment of the alcohol concentration which affects the transmission output power. However, the challenges are on choosing the right material and the simplicity on the fabrication of microfiber sensor for an improvement of the sensitivity of the sensor. A PMMA polymer microfiber doped MWCNTs was introduced for an application of alcohol detection system. Direct drawing technique was used to form a uniform waist size of microfiber sensor with 6µm diameter and 5mm length respectively. The performance of the fabricated sensor was tested with two types of alcohol, namely ethanol and 2-propanol at concentrations varying from 2% to 8% with 2% intervals. The performance which includes sensitivity, linearity and resolution were studied and analysed for the undoped PMMA and PMMA doped MWCNTs-doped polymer microfiber. The PMMA doped MWCNTs sensor which exhibited higher sensitivity for ethanol sensing with 83.23dBm/% with a linearity of 99.96% and a sensitivity of 73.75dBm/% with linearity 99.82% for 2- propanol sensing. The resolution has improved significantly by 0.0004% and 0.0007% respectively. In conclusion, PMMA doped MWCNTs was able to increase the sensitivity as well as the reproducibility of the microfiber sensor for the alcohol detection system.

Matched MeSH terms: Nanotubes, Carbon
On finite element modeling of single- and multi-walled carbon nanotubes

Rahmandoust M, Ochsner A

J Nanosci Nanotechnol, 2012 Oct;12(10):8129-36.
PMID: 23421189

In this study, Single-Walled and Multi-Walled Carbon Nanotubes in their perfect forms were investigated by the Finite Element Method. Details on the modeling of the structure are provided in this paper, including the appropriate elements, the element properties that should be defined based on the atomic structure of Carbon Nanotubes and the corresponding chemical bonds. Non-covalent van der Waals interactions between two neighbor atoms as well as the required approximations for the modeling of the structures with this kind of interaction are also presented. Specific attention was dedicated to the necessity of using some time- and energy-consuming steps in the simulation process. First, the effect of simulating only a single ring of the whole structure is studied to find out if it would represent the same mechanical behavior as the long structure. Results show that by applying an appropriate set of boundary conditions, the stiffness of the shortened structure is practically equal to the long perfect structure. Furthermore, Multi-Walled Carbon Nanotube structures with and without defining the van der Waals force are studied. Based on the observations, applying the van der Waals force does not significantly influence the obtained Young's modulus of the structure in the case of a uniaxial tensile test.

Matched MeSH terms: Nanotubes, Carbon
The effect of ammonia on carbon nanotube growth using simple thermal chemical vapour deposition

Teh AA, Ahmad R, Kara M, Rusop M, Awang Z

J Nanosci Nanotechnol, 2012 Oct;12(10):8201-4.
PMID: 23421197

We report the use of a new precursor as active agents to promote the growth of carbon nanotubes (CNT) in methane ambient using a simple thermal chemical vapour deposition method. The agents consist of ammonia and methanol mixed at different ratios and was found to enhance the growth of CNTs. The optimum methanol to ammonia ratio was found to be 8 to 5, whereby longer and denser CNTs were produced compared to other ratios. The result was found otherwise when the experiment was done solely in methane ambient. In addition, CNT growth on substrates coated with double layer Ni catalyst was improved in terms of quality and density compared to a single coated substrates. This finding is supported by Raman spectrometry analysis.

Matched MeSH terms: Nanotubes, Carbon
Metallic and semiconducting carbon nanotubes separation using an aqueous two-phase separation technique: a review

Tang MS, Ng EP, Juan JC, Ooi CW, Ling TC, Woon KL, et al.

Nanotechnology, 2016 Aug 19;27(33):332002.
PMID: 27396920 DOI: 10.1088/0957-4484/27/33/332002

It is known that carbon nanotubes show desirable physical and chemical properties with a wide array of potential applications. Nonetheless, their potential has been hampered by the difficulties in acquiring high purity, chiral-specific tubes. Considerable advancement has been made in terms of the purification of carbon nanotubes, for instance chemical oxidation, physical separation, and myriad combinations of physical and chemical methods. The aqueous two-phase separation technique has recently been demonstrated to be able to sort carbon nanotubes based on their chirality. The technique requires low cost polymers and salt, and is able to sort the tubes based on their diameter as well as metallicity. In this review, we aim to provide a review that could stimulate innovative thought on the progress of a carbon nanotubes sorting method using the aqueous two-phase separation method, and present possible future work and an outlook that could enhance the methodology.

Matched MeSH terms: Nanotubes, Carbon
Fulltext Effect of acid and Silane treated Carbon nanotubes on wear properties of Epoxy polymer composite

Aidah Jumahat, Napisah Sapiai, Eliya Farah Hana Mohd Kamal

Pertanika Journal of Science & Technology, 2017;25(103):213-222.
MyJurnal

This paper investigates the effect of acid and silane treatment of Carbon Nanotubes (CNT) on wear properties of epoxy polymer composite. The wear test done was based on ASTM D3389 standard using the Abrasive Wear Tester (TR 600). Characterisation analysis was also done using Transmission Electron Microscopy (TEM) in order to study the dispersion of the CNT inside the epoxy matrix. When untreated CNT was added to the epoxy with amounts of 0.5, 0.75 and 1.0 wt%, the wear rates did not improve except for 0.5 wt% CNT filled epoxy. This was due to the lack of dispersion which causes larger chunks of material being dug out, thus contributing to a higher mass loss and wear rate. When treated with acid and silane, 0.75 wt% and 1.0 wt% CNT filled epoxy composites showed improvement. The TEM images of 0.5 wt%, 0.75 wt% and 1.0 wt% PCNT filled epoxy supported the claim of the lack of dispersion of PCNT inside the epoxy.

Matched MeSH terms: Nanotubes, Carbon
Medium-chain-length poly-3-hydroxyalkanoates-carbon nanotubes composite anode enhances the performance of microbial fuel cell

Hindatu Y, Annuar MSM, Subramaniam R, Gumel AM

Bioprocess Biosyst Eng, 2017 Jun;40(6):919-928.
PMID: 28341913 DOI: 10.1007/s00449-017-1756-4

Insufficient power generation from a microbial fuel cell (MFC) hampers its progress towards utility-scale development. Electrode modification with biopolymeric materials could potentially address this issue. In this study, medium-chain-length poly-3-hydroxyalkanoates (PHA)/carbon nanotubes (C) composite (CPHA) was successfully applied to modify the surface of carbon cloth (CC) anode in MFC. Characterization of the functional groups on the anodic surface and its morphology was carried out. The CC-CPHA composite anode recorded maximum power density of 254 mW/m2, which was 15-53% higher than the MFC operated with CC-C (214 mW/m2) and pristine CC (119 mW/m2) as the anode in a double-chambered MFC operated with Escherichia coli as the biocatalyst. Electrochemical impedance spectroscopy and cyclic voltammetry showed that power enhancement was attributed to better electron transfer capability by the bacteria for the MFC setup with CC-CPHA anode.

Matched MeSH terms: Nanotubes, Carbon
Effect of nano- and micro- reinforced agents on dry sliding wear of polyester composites

Chong MM, Chang SY, Noraiham Muhammad, Zulkifli Mord Rosli, Qumrul Ahsan

Sains Malaysiana, 2014;43:959-966.

Dry sliding wear of polyester hybrid composites containing carboxylic functionalized multi-walled carbon nanotubes (cNT) and microparticles, silica (Si02) was studied at different sliding distances. An attempt has been made to produce uniform dispersion of nano- and micro- particles in the test samples by ultrasonication. The tribological properties of the hybrid composites were performed by using pin-on-disc (POD) tester against grey cast iron countersurface. The dry sliding wear tests were carried out under pressure-velocity (pv) condition of 0.4 MPa and 4 m/s for total sliding distance of 28800 m and at an interval of every sliding distance of 3600 m, wear properties and behavior were studied. The samples containing 10 wt.% silica (microparticles) with and without CNT always show increase in coefficient of friction at the expense of wear rate. However, samples containing only ci'rr have the lowest wear rate with the increase in coefficient of friction. Sliding distance studies also provide the information on wear rates which were ever changing at different sliding distances whereas average coefficient of friction did not vary throughout the tests. SEM observations of wear surfaces showed different wear morphologies when reinforcement (cNT or Si02) incorporated into the composites either alone or in combination.

Matched MeSH terms: Nanotubes, Carbon
Raman spectroscopy and X-ray photo-spectroscopy analysis of graphite media irradiated at low doses

Bradley DA, Siti Rozaila Z, Khandaker MU, Almugren KS, Meevasana W, Abdul Sani SF

Appl Radiat Isot, 2019 May;147:105-112.
PMID: 30852298 DOI: 10.1016/j.apradiso.2019.02.016

We explore the utility of controlled low-doses (0.2-100 Gy) of photon irradiation as initiators of structural alteration in carbon-rich materials. To-date our work on carbon has focused on β-, x- and γ-irradiations and the monitoring of radiotherapeutic doses (from a few Gy up to some tens of Gy) on the basis of the thermoluminescence (TL) signal, also via Raman and X-ray photo-spectroscopy (XPS), providing analysis of the dose dependence of single-walled carbon nanotubes (SWCNT). The work has been extended herein to investigate possibilities for analysis of structural alterations in graphite-rich mixtures, use being made of two grades of graphite-rich pencil lead, 8H and 2B, both being in the form produced for mechanical pencils (propelling or clutch pencils). 2B has the greater graphite content (approaching 98 wt %), 8H being a mixture of C, O, Al and Si (with respective weight percentages 39.2, 38.2, 9.8 and 12.8). Working on media pre-annealed at 400 °C, both have subsequently been irradiated to penetrating photon-mediated doses. Raman spectroscopy analysis has been carried out using a 532 nm laser Raman spectrometer, while for samples irradiated to doses from 1 to 40 Gy, XPS spectra were acquired using Al Kα sources (hv ∼1400 eV); carbon KLL Auger peaks were acquired using 50 eV Pass Energy. At these relatively low doses, alterations in order-disorder are clearly observed, defect generation and internal annealing competing as dominating effects across the dose range.

Matched MeSH terms: Nanotubes, Carbon
Dendrimer nanohybrid carrier systems: an expanding horizon for targeted drug and gene delivery

Kesharwani P, Gothwal A, Iyer AK, Jain K, Chourasia MK, Gupta U

Drug Discov Today, 2017 Jul 08.
PMID: 28697371 DOI: 10.1016/j.drudis.2017.06.009

Highly controllable dendritic structural design means dendrimers are a leading carrier in drug delivery applications. Dendrimer- and other nanocarrier-based hybrid systems are an emerging platform in the field of drug delivery. This review is a compilation of increasing reports of dendrimer interactions, such as dendrimer-liposome, dendrimer-carbon-nanotube, among others, known as hybrid carriers. This should prompt entirely new research with promising results for these hybrid carriers. It is assumed that such emerging hybrid nanosystems - from combining two already-established drug delivery platforms - could lead the way for the development of newer delivery systems with multiple applicability for latent theranostic applications in the future.

Matched MeSH terms: Nanotubes, Carbon
Fulltext Formation and yield of multi-walled carbon nanotubes synthesized via chemical vapour deposition routes using different metal-based catalysts of FeCoNiAl, CoNiAl and FeNiAl-LDH

Hussein MZ, Jaafar AM, Yahaya AH, Masarudin MJ, Zainal Z

Int J Mol Sci, 2014;15(11):20254-65.
PMID: 25380526 DOI: 10.3390/ijms151120254

Multi-walled carbon nanotubes (MWCNTs) were prepared via chemical vapor deposition (CVD) using a series of different catalysts, derived from FeCoNiAl, CoNiAl and FeNiAl layered double hydroxides (LDHs). Catalyst-active particles were obtained by calcination of LDHs at 800 °C for 5 h. Nitrogen and hexane were used as the carrier gas and carbon source respectively, for preparation of MWCNTs using CVD methods at 800 °C. MWCNTs were allowed to grow for 30 min on the catalyst spread on an alumina boat in a quartz tube. The materials were subsequently characterized through X-ray diffraction, Fourier transform infrared spectroscopy, surface area analysis, field emission scanning electron microscopy and transmission electron microscopy. It was determined that size and yield of MWCNTs varied depending on the type of LDH catalyst precursor that is used during synthesis. MWCNTs obtained using CoNiAl-LDH as the catalyst precursor showed smaller diameter and higher yield compared to FeCoNiAl and FeNiAl LDHs.

Matched MeSH terms: Nanotubes, Carbon/ultrastructure; Nanotubes, Carbon/chemistry*
Fulltext Fast synthesis of multilayer carbon nanotubes from camphor oil as an energy storage material

TermehYousefi A, Bagheri S, Shinji K, Rouhi J, Rusop Mahmood M, Ikeda S

Biomed Res Int, 2014;2014:691537.
PMID: 25258714 DOI: 10.1155/2014/691537

Among the wide range of renewable energy sources, the ever-increasing demand for electricity storage represents an emerging challenge. Utilizing carbon nanotubes (CNTs) for energy storage is closely being scrutinized due to the promising performance on top of their extraordinary features. In this work, well-aligned multilayer carbon nanotubes were successfully synthesized on a porous silicon (PSi) substrate in a fast process using renewable natural essential oil via chemical vapor deposition (CVD). Considering the influx of vaporized multilayer vertical carbon nanotubes (MVCNTs) to the PSi, the diameter distribution increased as the flow rate decreased in the reactor. Raman spectroscopy results indicated that the crystalline quality of the carbon nanotubes structure exhibits no major variation despite changes in the flow rate. Fourier transform infrared (FT-IR) spectra confirmed the hexagonal structure of the carbon nanotubes because of the presence of a peak corresponding to the carbon double bond. Field emission scanning electron microscopy (FESEM) images showed multilayer nanotubes, each with different diameters with long and straight multiwall tubes. Moreover, the temperature programmed desorption (TPD) method has been used to analyze the hydrogen storage properties of MVCNTs, which indicates that hydrogen adsorption sites exist on the synthesized multilayer CNTs.

Matched MeSH terms: Nanotubes, Carbon/ultrastructure; Nanotubes, Carbon/chemistry*
Fulltext Optimisation of the Photonic Efficiency of TiO2 Decorated on MWCNTs for Methylene Blue Photodegradation

Abdullahi N, Saion E, Shaari AH, Al-Hada NM, Keiteb A

PLoS One, 2015;10(5):e0125511.
PMID: 25993127 DOI: 10.1371/journal.pone.0125511

MWCNTs/TiO2 nanocomposite was prepared by oxidising MWCNT in H2SO4/HNO3 then decorating it with TiO2-p25 nanopowder. The composites were characterised using XRD, TEM, FT-IR PL and UV-vis spectroscopy. The TEM images have shown TiO2 nanoparticles immobilised onto the sidewalls of the MWCNTs. The UV-vis spectrum confirms that the nanocomposites can significantly absorb more light in the visible regions compared with the commercial TiO2 (P25). The catalytic activity of these nanocomposites was determined by photooxidation of MB aqueous solution in the presence of visible light. The MWCNTs/TiO2 (1:3) mass ratio showed maximum degradation efficiency. However, its activity was more favourable in alkaline and a neutral pH than an acidic medium.

Matched MeSH terms: Nanotubes, Carbon/ultrastructure; Nanotubes, Carbon/chemistry*
Enhanced dispersion of multiwall carbon nanotubes in natural rubber latex nanocomposites by surfactants bearing phenyl groups

Mohamed A, Anas AK, Bakar SA, Ardyani T, Zin WM, Ibrahim S, et al.

J Colloid Interface Sci, 2015 Oct 1;455:179-87.
PMID: 26070188 DOI: 10.1016/j.jcis.2015.05.054

Here is presented a systematic study of the dispersibility of multiwall carbon nanotubes (MWCNTs) in natural rubber latex (NR-latex) assisted by a series of single-, double-, and triple-sulfosuccinate anionic surfactants containing phenyl ring moieties. Optical polarising microscopy, field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), and Raman spectroscopy have been performed to obtain the dispersion-level profiles of the MWCNTs in the nanocomposites. Interestingly, a triple-chain, phenyl-containing surfactant, namely sodium 1,5-dioxo-1,5-bis(3-phenylpropoxy)-3-((3-phenylpropoxy)carbonyl) pentane-2-sulfonate (TCPh), has a greater capacity the stabilisation of MWCNTs than a commercially available single-chain sodium dodecylbenzenesulfonate (SDBS) surfactant. TCPh provides significant enhancements in the electrical conductivity of nanocomposites, up to ∼10(-2) S cm(-1), as measured by a four-point probe instrument. These results have allowed compilation of a road map for the design of surfactant architectures capable of providing the homogeneous dispersion of MWCNTs required for the next generation of polymer-carbon-nanotube materials, specifically those used in aerospace technology.

Matched MeSH terms: Nanotubes, Carbon/ultrastructure; Nanotubes, Carbon/chemistry*
Fulltext Construction of an Electrochemical Sensor Based on Carbon Nanotubes/Gold Nanoparticles for Trace Determination of Amoxicillin in Bovine Milk

Muhammad A, Yusof NA, Hajian R, Abdullah J

Sensors (Basel), 2016;16(1).
PMID: 26805829 DOI: 10.3390/s16010056

In this work, a novel electrochemical sensor was fabricated for determination of amoxicillin in bovine milk samples by decoration of carboxylated multi-walled carbon nanotubes (MWCNTs) with gold nanoparticles (AuNPs) using ethylenediamine (en) as a cross linker (AuNPs/en-MWCNTs). The constructed nanocomposite was homogenized in dimethylformamide and drop casted on screen printed electrode. Field emission scanning electron microscopy (FESEM), energy dispersive X-Ray (EDX), X-Ray diffraction (XRD) and cyclic voltammetry were used to characterize the synthesized nanocomposites. The results show that the synthesized nanocomposites induced a remarkable synergetic effect for the oxidation of amoxicillin. Effect of some parameters, including pH, buffer, scan rate, accumulation potential, accumulation time and amount of casted nanocomposites, on the sensitivity of fabricated sensor were optimized. Under the optimum conditions, there was two linear calibration ranges from 0.2-10 µM and 10-30 µM with equations of Ipa (µA) = 2.88C (µM) + 1.2017; r = 0.9939 and Ipa (µA) = 0.88C (µM) + 22.97; r = 0.9973, respectively. The limit of detection (LOD) and limit of quantitation (LOQ) were calculated as 0.015 µM and 0.149 µM, respectively. The fabricated electrochemical sensor was successfully applied for determination of Amoxicillin in bovine milk samples and all results compared with high performance liquid chromatography (HPLC) standard method.

Matched MeSH terms: Nanotubes, Carbon/ultrastructure; Nanotubes, Carbon/chemistry*

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links