This study aimed at investigating the performances of air drying of blackberries assisted by airborne ultrasound and contact ultrasound. The drying experiments were conducted in a self-designed dryer coupled with a 20-kHz ultrasound probe. A numerical model for unsteady heat and mass transfer considering temperature dependent diffusivity, shrinkage pattern and input ultrasonic energies were applied to explore the drying mechanism, while the energy consumption and quality were analyzed experimentally. Generally, both airborne ultrasound and contact ultrasound accelerated the drying process, reduced the energy consumption and enhanced the retentions of blackberry anthocyanins and organic acids in comparison to air drying alone. At the same input ultrasound intensity level, blackberries received more ultrasound energies under contact sonication (0.299 W) than airborne sonication (0.245 W), thus avoiding the attenuation of ultrasonic energies by air. The modeling results revealed that contact ultrasound was more capable than airborne ultrasound to intensify the inner moisture diffusion and heat conduction, as well as surface exchange of heat and moisture with air. During air drying, contact ultrasound treatment eliminated the gradients of temperature and moisture inside blackberry easier than airborne ultrasound, leading to more homogenous distributions. Moreover, the total energy consumption under air drying with contact ultrasound assistance was 27.0% lower than that with airborne ultrasound assistance. Besides, blackberries dehydrated by contact ultrasound contained more anthocyanins and organic acids than those dried by airborne ultrasound, implying a higher quality. Overall, direct contact sonication can well benefit blackberry drying in both energy and quality aspects.
The aim of this study was to determine the effect of different ratios of low protein flour to oyster mushroom (Pleurotus sajor-caju) powder on the physicochemical properties and sensory acceptability of edible tablespoon. Fresh grey oyster mushroom was dried in a convection oven at temperature of 55.0˚C ± 2.0˚C for 20 h prior to the grinding process. The low protein flour (LPF) was then incorporated with oyster mushroom powder (OMP) at different ratios of 100:0, 96:4, 92:8, 88:12 and 84:16, before being with vegetable oil, sugar, egg white and water in formulating the edible tablespoon. The proximate analyses were carried out in triplicate for calorie content, colour profile, hardness value and morphological structure of edible tablespoon. This study revealed that with decreasing LPF and increasing OMP in the formulation, the ash content (1.24% to 1.92%), crude fat content (8.98% to 10.40%) and fiber content (0.13% to 1.24%) were observed to have increased as well as the hardness value (2042.03g to 2844.57g) and pore’s size of the morphological structure of edible tablespoon. However, the carbohydrate content (78.64% to 75.56%) significantly decreased (p>0.05) together with L* value (from 68.47 to 61.71) when the decrease was in the the percentage of LPF and an increase the percentage of OMP. The calorie content, moisture content and protein content of edible tablespoon were not significantly (p>0.05) affected by different ratios of LPF to OMP. The edible tablespoon formulated with up to 8% of OMP was accepted by the sensory panelists but further increase in OMP addition significantly decreased the degree of likeness in terms of colour, odour, taste and overall acceptability of edible tablespoon. This study suggested that oyster mushroom edible tablespoon could be potential alternative disposable cutlery which will help to reduce the use of huge amount of non-biodegradable materials for environmental conservation.
Red Palm Weevil (RPW), Rhynchophorus ferrugineus is a lethal pest which has been described as a serious pest that reduces the production of coconut tree and other major cultivated palms. RPW infestation was initially detected by Department of Agriculture (DOA) in 2007 in all eight Terengganu districts. Rhu Tapai plantation area is one of the highly infested areas in Terengganu. Until now, limited reports on population abundance of this lethal pest have been discussed particularly in Rhu Tapai. Therefore, a study on population abundance is a must in order to understand the population dynamic of RPW which will be the first step of its control strategy. A total of 12 traps were installed and synthetic pheromones (P028 Ferrolure+) were used in attracting the RPW adults. Overall, 81 individuals of RPW were successfully collected after 16 weeks of pheromone trapping (3rd September until 28th November 2018). The trend of weekly RPW captured was eventually decreasing from Week 1 to Week 16 but showed a sudden increment in Week 10. Pandan cultivar plot captured the highest number of adult RPW compared with Mawa cultivar plots. Result showed no significant difference between RPW sexes percentage of sexes which was 53% of male and 47% of female (1:1 ratio) (U= 0.143, p > 0.05). Daily rainfall and temperature significantly reduced the trapping efficiency (R²rainfall = 0.142, p = 0.145; R²temperature = 0.0858; p = 0.258). These results will be the baseline information for future study regarding control management strategy using pheromone-based mass trapping system.
Synthesis of nanoparticles by using plant have sparked interest among researchers due to environmentally safe, inexpensive and simple method to compare with chemical method. Use of plant in synthesis zinc oxide nanoparticles (ZnO NPs) that act as reducing and capping agent are more recommended, due to high production of product and rate of synthesis is faster than using microorganism. This study focus on the synthesis of ZnO NPs by using leaf extract of aloe vera (Aloe bardenisis miller) with different concentration (30%, 40% and 50%) and various calcination temperature which are 500 ˚C, 700 ˚C and 900 ˚C for 4 hours. Fourier – transform infrared spectroscopy (FTIR), Thermogravimetric Analysis (TGA), scanning electron microscopy (SEM), X-ray Diffraction (XRD) and Brunauer-Emmet and Teller (BET) were used to characterize the prepared samples. FTIR spectra showed present wavenumber in between 400-500 cm-1 indicated the presence of Zn-O stretch. Powder XRD pattern confirmed the hexagonal wurtzite structure with average particles size from 24.19 nm to 67.69 nm for all concentration and temperature by using Scherer’s equation. For SEM analysis the images show irregular shape for concentrations 30% and 50% with size range from 500 nm to 900 nm while for concentration 40% cubic shape was observe with size range from 140 nm to 900 nm. All characterize show that formation of ZnO NPs depend on the concentration and calcination temperature. Sample 30% and 50% ZnO NPs was applied in lithium battery at voltage from 0.01 to 3. 1.2 mAhg-1 was recorded for sample 30% ZnO NPs while 100 mAhg-1.
Lipases are enzyme with versatile industrial applications can be produced by the solid-state fermentation (SSF) method and is an economical alternative for enzyme production assisted by fungus. In Malaysia, 5 million of copra waste were generated annually. Large amount of copra waste produced will cause an increasing amount of the waste dumped to the landfill. Copra waste is one of the potential substrates to produce lipase enzyme through SSF. Thus, the aim of this study is to optimize the lipase production by SSF associated by Aspergillus niger using the 23 full factorial design approach. In this study the factors affecting parameters that involved in the production of lipase enzyme such as temperature (25˚ and 35˚), substrates concentration (40% and 60%) and inoculum size of Aspergillus niger (1 and 9 petri dish) were determined. The maximum production of lipase was obtained after 120-hour incubation in SSF. The optimum condition for inoculum size of Aspergillus niger was 9 plates, 30°C of incubation temperature and 60 % moisture contents. The range of the concentration of lipase enzyme produced varied from 105 U/ml to 170 U/ml. When applied to the wastewater treatment, the reducing percentage of fat, oil and grease (FOG) in food processing wastewater is reduced from 219.4925mg/l to 169.467mg/l accounted to the amount of 34 % FOG removal. Lipase produced using copra waste as a substrate using SSF has the potential value to be developed in the future for various industry including wastewater treatment industry.
Plastics packaging is non-biodegradable and risks to human health and environmental pollution. In contrast, gelatin-based film lack of desired mechanical, thermal and water vapour barrier properties. Thus, this study aimed to investigate the mechanical and physical properties of bio-nanocomposite films based on chicken skin gelatin with different concentration of chitosan nanoparticles (CSNPs). Gelatin/CSNPs film solutions with different CSNPs concentration (0-8%, w/w) were stirred at 45oC for 30 min and oven-dried at 45oC. Film characterization determination includes tensile strength (TS), elongation at break (EAB), Young’s modulus (YM), water solubility, water vapour permeability (WVP), film morphology and melting temperature (Tm). Results of the study indicated that incorporation of CSNPs significantly influenced film properties. The addition of CSNPs increased the TS and YM value, which lead to stronger films than the pure chicken skin gelatin films. However the addition of CSNPs decreased the EAB value. Furthermore, WVP and water solubility significantly decreased (p < 0.05) by the addition of 6% CSNPs. Morphology images showed that increased CSNPs reduced the film’s amorphous character, especially in high level, in which higher CSNPs (8%) resulted in the aggregation of particles in the composites. The nano-reinforcement films showed higher thermal stability as compared to pure chicken skin gelatin films. In conclusion, the film with 6% CSNPs showed the best formulation, as it demonstrated high in TS, YM and Tm value, while low in EAB, water solubility and WVP value compared to other films. The results presented in this study showed the feasibility of using bio-nanocomposite technology to improve the properties of biopolymer films based on chicken skin gelatin.
The concentrations of airborne particulate matter (PM) is often measured as a mass concentration. However, the other way to express particulate matter is by using the Particle Number Count ([PNC]) concentrations. This study aims to analyse the seasonal variation of airborne particulate matter in terms of [PNC] by using R packages and the Boosted Regression Trees (BRTs) technique. The study was conducted at IOES, Universiti of Malaya in Bachok, Kelantan. The monitoring was important to understand the variability of seasonal effects due to different seasons. In this work, only the datasets for three seasons (Inter Monsoon, North East Monsoon and South-West Monsoon) were analysed involving 25,958 data. The air quality monitoring equipment involved was the particle counter Environment Dust Monitor GRIMM Model 180 and a weather station for recording the meteorological parameters. The data analysis was completed by using R software and its package for evaluating seasonal variability and providing the statistical analysis. The relationship between variables was studied by using the Boosted Regression Tree (BRT) technique. The interaction between independent variables towards the [PNC] in different seasons was discussed. The best setting result of BRT model evaluation R² is 0.22 (North-East Monsoon), 0.87 (Intern monsoon 1), and 0.59 for South West Monsoon which indicated that the model developed is acceptable except for NEM and intern monsoon seasons. Temperature (57 %) and wind direction (67%) were found to be the highest factor influenced by the formation of [PNC] concentrations in this area. Finally, good results indicated that BRT technique is an acceptable way to analysed air pollution data.
Green amaranth (Amaranthus viridis L.) is one of the most popular leafy vegetables cultivated in Malaysia. Photo-selective netting is a revolutionary agricultural-technical idea, allowing traditional nets to be improved to a sophisticated level, which can impact microclimate and solar radiation as well as protect crops from pests. This study aims to investigate the growth performance of green amaranth under different three different treatments of photo-selective nets including black, and yellow shade nets and control. The assessed physiological, pre-harvest and post-harvest parameters were air temperature and relative humidity, measurement of absorption of photosynthetically active radiation (PAR), plant height, number of leaves, and dry weight. This study found that the yellow shade net showed the best performance in plant growth with the average difference in plant height (4.11 cm), average leaves number (7 leaves) and average dry weight (18.58 mg) were the highest compared to black shade net and control (without shading). In conclusion, photo-selective yellow shade net was able to enhance the growth development of green amaranth and could be applied in the large scale production to boost the growth and yield of leafy vegetables.
Tomatoes have a short shelf life thus they pose a big challenge for growers to maintain the quality of tomatoes to increase customer acceptance. In this study, fungi associated with tomato disease symptoms were isolated and the potential of kaffir lime aqueous extract was evaluated in maintaining post-harvest quality of tomatoes. For this purpose, healthy tomatoes were dipped in 10% aqueous kaffir lime extract before evaluating the post-harvest parameters namely weight loss and firmness. A fungus namely Rhizophus stolonifer was isolated from the symptomatic tomatoes. Subsequently, it was confirmed to be pathogenic on healthy tomato fruits with 100% disease severity. Application of aqueous kaffir lime extract showed that tomato fruits dipped in 10% aqueous kaffir lime extract recorded higher weight loss and higher firmness as compared to untreated tomato fruits. The results showed that treatment with this concentration of plant extract did not help to reduce the weight loss, but it retained the firmness of the tomato fruits stored at room temperature at 27+2oC. Higher transpiration process would lead to shrinkage, weight loss, changes in texture and appearance of the fruits. Therefore, this study suggested an increased concentration of aqueous kaffir lime extract as a treatment agent in order to have a better effect in maintaining the quality of tomato fruits.
Solar photocatalysis is a green technology that takes advantage of sustainable solar energy for enhancing oxidation process of numerous harmful water contaminants. In this study, a custom solar driven zinc oxide (ZnO)-mediated photocatalytic system was developed and its efficiency to remove organic contaminants as well as to disinfect selected bacteria was investigated. Methylene blue (MB) dye was used as the model organic contaminant, while Escherichia coli(E.coli) was used as the model fecal coliform bacteria in contaminated water. A series of photodegradation experiments were conducted on water contaminated with either 10 mg/L of MB or ~1010CFU/ml of E.coli. The experiments were completed under sunlight irradiation in the presence of 1 g/L of nano ZnO photocatalyst for up to 6 hours. Using a solar thermal collector, the photoreactor operated in the temperature range of 25 to 50 oC. The findings revealed that the combination of solar thermal with solar photocatalysis usingZnO intensified the degradation of MB and disinfection of E.coli. 98.08% of MB dye and 99.99% of E.coliwere successfully removed from the water within the first 3 hours of treatment. Almost complete removal was eventually achieved after 6 hours of treatment. It is therefore suggested that ZnO-based solar photocatalytic system developed in this study is highly efficient at enhancing water decontamination process.
Fine particulate matter (aerodynamic diameter ≤2.5 μm) (PM2.5) has become a major concern because it can adsorb chemicals e.g. polycyclic aromatic hydrocarbons (PAHs) onto its surface. Although PAHs are priority pollutants that can cause adverse health effect, there is still limited information concerning indoor exposures to PAHs in Malaysia. This study aimed to characterise the distribution of PAHs bounded to PM2.5in primary school environments. Indoor and outdoor PM2.5 were collected between May and July 2017 using low volume samplers (LVS) at three public primary schools in the Federal Territory of Kuala Lumpur. PAHs were extracted by ultrasonic extraction with Dichloromethane: n-Hexane (1:1, v/v) as the extraction solvent and analysed using gas chromatography coupled with mass spectrometer (GC-MS). Based on the results, the average total concentration of PAHs (∑PAHs) ranged from 3.8 to 10.1 ng m-3and 1.6 to 8.0 ng m-3for outdoors and indoors, respectively. PAHs in PM2.5samples indicated the potential contribution of combustion at high temperature and indoor sources and the infiltration of outdoor PAHs were the important sources for outdoor and indoor, respectively. In addition, the diagnostic ratio analysis showed that vehicular emissions were the most predominant sources of PAHs in school environments.
A series of nine methyl sulphones ( 3a -3 i ) starting from the aldehydes ( 1a-1i ) were synthesized in two consecutive steps. In the first step, preparation of allyl alcohols ( 2a-2i ) from their corresponding aldehydes by the reaction of sodium borohydride in methanol at room temperature is reported. Finally, methyl sulphones are synthesized by condensing sodium methyl sulfinates with allyl alcohols in the presence of BF 3 .Et 2 O in acetic acid medium at room temperature for about 2-3 h. The reaction conditions are simple, yields are high (85%-95%), and the products were obtained with good purity. All the synthesized compounds were characterized by their 1 H, 13 C NMR, and mass spectral analysis. All the title compounds were screened for antimicrobial activity. Among the compounds tested, the compound 3f has inhibited both Gram positive and Gram negative bacteria effectively and compound 3i has shown potent antifungal activity. These promising components may help to develop more potent drugs in the near future for the treatment of bacterial and fungal infections.
This work introduces a new additive named 4,4'-trimethylenedipiperidine for the practical and ecofriendly preparation of ethyl 5-amino-7-(4-phenyl)-4,7-dihydro-[1,2,4]triazolo[1,5-a]pyrimidine-6-carboxylate derivatives. This chemical is commercially available and easy to handle. It also possesses a low melting point and a broad liquid range temperature, high thermal stability, and good solubility in water. Based on green chemistry principles, the reaction was performed in a) a mixture of green solvents i.e. water and ethanol (1:1 v/v) at reflux temperature, and b) the additive was liquefied at 65 °C and the reaction was conducted in the liquid state of the additive. High yields of the desired triazolo-pyrimidines were obtained under both aforementioned conditions. Our results demonstrated that this additive, containing 2 Lewis base sites and able to act as an acceptor-donor hydrogen bonding group, is a novel and efficient alternative to piperidine, owing to its unique properties such as its reduced toxicity, nonflammable nature, nonvolatile state, broad liquid range temperature, high thermal stability, and ability to be safely handled. Furthermore, this additive could be completely recovered and exhibited high recyclability without any change in its chemical structure and no significant reduction in its activity. The current methodology has several advantages: (a) it avoids the use of hazardous materials, as well as toxic, volatile, and flammable solvents, (b) it does not entail tedious processes, harsh conditions, and the multistep preparation of catalysts, (c) it uses a metal-free and noncorrosive catalyst, and (d) reduces the generation of hazardous waste and simple work-up processes. The most important result of this study is that 4,4'-trimethylenedipiperidine can be a promising alternative for toxic, volatile, and flammable base reagents in organic synthesis owing to its unique properties.
The distribution of benthic Foraminifera throughout the coastal waters of Taman Negara Pulau Pinang (Penang National Park), Malaysia was studied to assess the impact of various anthropogenic activities, such as fishing, ecotourism and floating cage culture. Samples were obtained at 200 m intervals within the subtidal zone, extending up to 1200 m offshore at Teluk Bahang, Teluk Aling, Teluk Ketapang and Pantai Acheh. The depth within coastal waters ranged between 1.5 m and 10.0 m, with predominantly muddy substrate at most stations. Water quality analysis showed little variation in micronutrient (nitrite, NO2; nitrate, NO3; ammonia, NH4 and orthophosphate, PO4) concentrations between sampling stations. Temperature (29.6±0.48°C), salinity (29.4±0.28 ppt), dissolved oxygen content (5.4±0.95 mg/l) and pH (8.5± 0.13) also showed little fluctuation between stations. A total of nine genera of foraminifera were identified in the study (i.e., Ammonia, Elphidium, Ammobaculites, Bigenerina, Quinqueloculina, Reopax, Globigerina, Textularia and Nonion). The distribution of benthic foraminifera was dominated by opportunistic groups that have a high tolerance to anthropogenic stressors. Ammonia had the highest frequency of occurrence (84.7%), followed by Bigenerina (50%), Ammobaculites (44.2%) and Elphidium (38.9%). The Ammonia-Elphidium Index (AEI) was used to describe the hypoxic condition of benthic communities at all sites. Teluk Bahang had the highest AEI value. The foraminiferal assemblages and distribution in Teluk Bahang, Teluk Aling, Teluk Ketapang and Pantai Acheh showed no correlation with physical or chemical environmental parameters.
This paper aimed to describe the effects of sand mining on the Kelantan River with respect to physical and chemical parameter analyses. Three replicates of water samples were collected from five stations along the Kelantan River (November 2010 until February 2011). The physical parameters included water temperature, water conductivity, dissolved oxygen (DO), pH, total dissolved solids (TDS), total suspended solids (TSS) and turbidity, whereas the chemical parameters included the concentration of nitrogen nutrients such as ammonia, nitrate and nitrite. The Kelantan River case study revealed that TSS, turbidity and nitrate contents exceed the Malaysian Interim National Water Quality Standard (INWQS) range and are significantly different between Station 1 (KK) and Station 3 (TM). Station 1 has the largest variation of TDS, TSS, turbidity and nitrogen nutrients because of sand mining and upstream logging activities. The extremely high content of TSS and the turbidity have caused poor and stressful conditions for the aquatic life in the Kelantan River.
In this study, factor analysis (FA) was applied to extract the hidden factors responsible for water quality variations during both wet and dry seasons. Water samples were collected from six sampling stations (St. 1 Lalang River, St. 2 Semeling River, St. 3 Jagung River, St. 4 Teluk Wang River, St. 5 Gelam River and St. 6 Derhaka River) in the Merbok estuary, Malaysia from January to December 2011; the samples were further analysed in the laboratory. Correlation analysis of the data sets showed strong correlations between the parameters. Nutrients such as nitrate (NO3 (-)), nitrite (NO2 (-)), ammonia (NH3) and phosphate (PO4 (3-)) were determined to be critical indicators of water quality throughout the year. Influential water quality parameters during the wet season were conductivity, salinity, biochemical oxygen demand (BOD), dissolved oxygen (DO) and chlorophyll a (Chla), whereas total suspended solid (TSS) and pH were critical water quality indicators during the dry season. The Kruskal-Wallis H test showed that water quality parameters were significantly different among the sampling months and stations (p<0.05), and Mann-Whitney U tests further revealed that the significantly different parameters were temperature, pH, DO, TSS, NO2 (-) and BOD (p<0.01), whereas salinity, conductivity, NO3 (-), PO4 (3-), NH3 and Chla were not significantly different (p>0.05). Water quality parameters in the estuary varied on both temporal and spatial scales and these results may serve as baseline information for estuary management, specifically for the Merbok estuary.
The life history and the influence of environmental parameters on Thalerosphyrus were investigated in two first-order rivers-the Batu Hampar River and the Teroi River of Gunung Jerai, Kedah-in northern peninsular Malaysia. Based on nymphal body length, Thalerosphyrus was found to be trivoltine in both rivers, regardless of the altitudinal difference, but its population abundance was four times higher in the Teroi River, presumably related to its better survival in the lower water temperature. At least nine instars of Thalerosphyrus were detected in the field-collected nymphs. Its life cycle was completed within 2.5-3.0 months, with overlapping cohorts and continual emergence of up to 3 months. The main driving factors of the high abundance of Thalerosphyrus were the water temperature and habitat quality.
Many reports have revealed that the abundance of microalgae in shrimp ponds vary with changes in environmental factors such as light, temperature, pH, salinity and nutrient level throughout a shrimp culture period. In this study, shrimp cultivation period was divided into three stages (initial = week 0–5, mid = week 6–10 and final = week 11–15). Physical and chemical parameters throughout the cultivation period were studied and species composition of microalgae was monitored. Physical parameters were found to
fluctuate widely with light intensity ranging between 182.23–1278 µmol photon m–2s–1, temperature between 29.56ºC –31.59ºC, dissolved oxygen (DO) between 4.56–8.21 mg/l, pH between 7.65–8.49 and salinity between 20‰–30‰. Ammonium (NH4+-N), nitrite (NO2– -N), nitrate (NO3– -N), and orthophosphate (PO43– -P) concentrations in the pond at all cultivation stages ranged from 0.017 to 0.38 mg/l, 0.24 to 2.12 mg/l, 0.06 to 0.98 mg/l and 0.16 to 1.93 mg/l respectively. Statistical test (ANOVA) showed that there were no significant difference (p
Many reports have revealed that the abundance of microalgae in shrimp ponds vary with changes in environmental factors such as light, temperature, pH, salinity and nutrient level throughout a shrimp culture period. In this study, shrimp cultivation period was divided into three stages (initial = week 0-5, mid = week 6-10 and final = week 11-15). Physical and chemical parameters throughout the cultivation period were studied and species composition of microalgae was monitored. Physical parameters were found to fluctuate widely with light intensity ranging between 182.23-1278 μmol photon m(-2)s(-1), temperature between 29.56°C -31.59°C, dissolved oxygen (DO) between 4.56-8.21 mg/l, pH between 7.65-8.49 and salinity between 20‰-30‰. Ammonium (NH4 (+)-N), nitrite (NO2 (-)-N), nitrate (NO3 (-)-N), and orthophosphate (PO4 (3-)-P) concentrations in the pond at all cultivation stages ranged from 0.017 to 0.38 mg/l, 0.24 to 2.12 mg/l, 0.06 to 0.98 mg/l and 0.16 to 1.93 mg/l respectively. Statistical test (ANOVA) showed that there were no significant difference (p<0.05) in nutrients concentrations among the cultivation stages. All nutrients concentrations however were still in the tolerable level and safe for shrimp culture. The chlorophyll a contents were found to range from 5.03±2.17 to 32.61±0.35 μg/l throughout the cultivation period. A total of 19 microalgae species were found in the shrimp pond, with diatoms contributing up to 72% of the species followed by Chlorophyta (11%) and Cyanophyta (11%). However, weekly species abundance varied through the study period. At the initial stage, when there were no shrimps in the pond, Anabaena spp. and Oscillatoria spp. (Cyanophyta) were the dominant species, followed by Chlorella sp. and Dunaliella sp. (Chlorophyta). When shrimps were introduced into the pond, Amphora sp., Navicula sp. Gyrosigma sp. and Nitzschia sp. (diatoms) started to exist. At the middle and towards the final stage of the shrimp culture period diatoms were the dominant species. The Chlorophyta (Chlorella sp.) domination took place only twice, which was at week 2 and 13. The absence of some of the coastal water microalgae species in the shrimp pond was most likely due to the fact that they could not tolerate the physicochemical factors of harsh environment. In this study, Cylindrotheca closterium was regarded as the most tolerant species among the microalgae due to its ability to exist for 6 weeks out of the 15 weeks of cultivation.
Seeds of two selected clones of Artemisia annua L., TC1 and TC2, were germinated in a greenhouse. Four-week-old seedlings from both clones were grown in the Thù Đúc province of Ho Chi Minh City on 2(nd) January 2009 and Đà Lat on 20(th) January 2009. During this study period in Thù Đúc province, which is situated 4-5 m above sea level, was experiencing a tropical, dry season with temperatures ranging from 26.2°C-32.8°C. Đà Lat, situated at 1500-2000 m above sea level, was having temperate, dry season with lower temperatures, ranging from 10.5°C-18.0°C. The high temperatures and low elevation in Thù Đúc Province led to slow vegetative growth for all of the plants from the two different clones and the artemisinin contents were significantly reduced. The temperate environment of Đà Lat supported robustly growing plants, with plant heights and branch lengths 4-5 times taller and longer that those planted at Thù Đúc Province. The artemisinin contents of A. annua planted at Đà Lat were 3-4 times greater than those cultivated at Thù Đúc Province. Hence, this study indicated that the variations observed in plant growth and artemisinin contents were due to temperature effects because the two selected clones were genetically homogenous. The cold weather of Đà Lat was suitable for planting of A. annua as opposed to the tropical weather of Thù Đúc Province.