β-tricalcium phosphate (β-TCP) powders were synthesized by using various particles sizes (40 nm – 780 μm) calcium carbonate (CaCO3) and phosphoric acid (H3PO4) at room temperature (25 ˚C). The synthesized powders were characterized by using X-Ray Diffraction (XRD) method. The purity of β-TCP powders were determined from XRD pattern while the crystallite size of β-TCP powders were calculated by using Scherrer equation. Results shows that the purity of β-TCP powders were ranged from 20.33 % to 81.94 % while the crystallite size of β- TCP powders were ranged from 0.04391 μm to 0.06751 μm. From this work, particle size of CaCO3 will influenced the purity but not the mean crystallite size of synthesized β-TCP.
Indialite or α-cordierite was synthesized by glass crystallization method using mainly talc and kaolin and with small amount of MgO, Al2O3, SiO2 to compensate the chemical formulation of non-stoihiometric compositions of cordierite. (3MgO.1.5Al2O3.5SiO2). B2O3, P2O5 and CaO was also added to decrease the melting and sintering temperature of cordierite. The glasses were pelletized and sintered from 850 o C up to 1050 o C. Phase compositions of both heat treated glass was quantified by X-ray powder diffraction data by the Rietveld method using TOPAS Ver 3 software. Result shows that about 60wt% of α cordierite has successfully crystallized at 850 o C. Beside secondary phases (forsterite) which come from initial raw materials, phases from grinding media were also presents in the sample. The contamination was considered high since it has reacted with existence phases to form a new phase at higher temperature. Without any contamination from grinding it was expected to obtain more than 90wt% α cordierite using the same composition.
This article presents the development of a low-cost microcontroller-based interface for a microbioreactor operation. An Arduino MEGA 2560 board with 54 digital input/outputs, including 15 pulse-width-modulation outputs, has been chosen to perform the acquisition and control of the microbioreactor. The microbioreactor (volume = 800 µL) was made of poly(dimethylsiloxane) and poly(methylmethacrylate) polymers. The reactor was built to be equipped with sensors and actuators for the control of reactor temperature and the mixing speed. The article discusses the circuit of the microcontroller-based platform, describes the signal conditioning steps, and evaluates the capacity of the proposed low-cost microcontroller-based interface in terms of control accuracy and system responses. It is demonstrated that the proposed microcontroller-based platform is able to operate parallel microbioreactor operation with satisfactory performances. Control accuracy at a deviation less than 5% of the set-point values and responses in the range of few seconds have been recorded.
Raising the thermal expansion coefficient (CTE) of dental porcelains is important to match the CTE of the ceramic material with the higher CTE of the metal inlay in dental restorations. The higher thermal expansion of the leucite phase increases the overall thermal expansion coefficient of the dental porcelain. Potassium nitrate (KNO3) additions in controlled percentages to the base dental porcelain formulation help in the formation of a leucite phase. The percentage added was 5,10 and 20 weight percent of leucite, respectively, to the total base frit composition. The change in CTE values was then investigated using a Linseis Dilatometer. A 20wt% KNO3 addition resulted in a CTE of 9.0 microm/m-K compared to the 7.7 microm/m-K CTE of the base composition. The microstructures observed under the scanning electron microscope (SEM) show a multiphase material with the leucite phases dispersed within a glassy matrix. The results suggest that higher CTEs in the dental porcelain are possible by increasing the KNO3- additions within the limits tested.
CaCu3Ti4O12 (CCTO) has attracted a great attention for electronic devices miniaturization due to its
very high dielectric constant properties at a wide range of frequency and nearly constant over broad temperature range. The origins of the giant dielectric constant have been speculated from electrical heterogeneous of interior elements of the CCTO ceramics. Four origins were suggested contributed to the electrical heterogeneous. In this study heat treatment were done with the electrode contact in Argon gas environment and the electrical properties over very wide frequency of CCTO ceramics were investigated. Cylindrical CCTO pellets samples were prepared by solid state reaction method and single phase of XRD pattern was obtained after sintering processes. Electrical impedance responds were measured at frequency from 100 Hz to 1 GHz for the samples for untreated and heat treated at 200ºC, 250ºC, 300ºC, 350ºC and 400ºC of CCTO. Improvement to the dielectric constant can be seen for 350ºC and 400ºC samples and dielectric loss were improved for 200ºC and 300ºC samples for overall frequency. The variations were discussed based on oxygen deficiency content and resistivity of the elements inside of CCTO structure.
This study examines the feasibility of catalytically pretreated biochar derived from the dried exocarp or fruit peel of mangostene with Group I alkali metal hydroxide (KOH). The pretreated char was activated in the presence of carbon dioxide gas flow at high temperature to upgrade its physiochemical properties for the removal of copper, Cu(II) cations in single solute system. The effect of three independent variables, including temperature, agitation time and concentration, on sorption performance were carried out. Reaction kinetics parameters were determined by using linear regression analysis of the pseudo first, pseudo second, Elovich and intra-particle diffusion models. The regression co-efficient, R² values were best for the pseudo second order kinetic model for all the concentration ranges under investigation. This implied that Cu(II) cations were adsorbed mainly by chemical interactions with the surface active sites of the activated biochar. Langmuir, Freundlich and Temkin isotherm models were used to interpret the equilibrium data at different temperature. Thermodynamic studies revealed that the sorption process was spontaneous and endothermic. The surface area of the activated sample was 367.10 m²/g, whereas before base activation, it was only 1.22 m²/g. The results elucidated that the base pretreatment was efficient enough to yield porous carbon with an enlarged surface area, which can successfully eliminate Cu(II) cations from waste water.
Cloud point extraction (CPE) is a separation and preconcentration of non-ionic surfactant from one liquid phase to another. In this study, Sylgard 309 and three different types of additives for CPE, namely CPE-Sylgard, CPE-Sylgard-BMIMBr and CPE-Sylgard-GLDA, are investigated to extract methylphenol from water samples. The methylphenols are well separated by reversed-phase high-performance liquid chromatography (HPLC) with isocratic elution of acetonitrile : water; 60 : 40 (v/v) and detection at 260 nm. The optimized parameters for the effect of salt, surfactant, temperature, time of extraction, pH, interference study and the performance of different additives on methylphenol extraction are investigated. CPE-Sylgard-GLDA is chosen because it gives us a high peak and good peak area compared with CPE-Sylgard and CPE-Sylgard-BMIMBr. The recovery extractions of CPE-Sylgard-GLDA are obtained in the range of 80-99% as the percentage of relative standard deviation (RSD) is less than 10. The LOD and LOQ are 0.05 ppm and 0.18 ppm, respectively. The method developed for CPE-Sylgard-GLDA coupled with HPLC is feasible for the determination of methylphenol because it is simple, effective, cheap, and produces a high percentage of recovery.
The aim of the work reported in this article was to investigate the effects of medium temperature and industrial by-products on the key hardened properties of high performance concrete. Four concrete mixes were prepared based on a water-to-binder ratio of 0.35. Two industrial by-products, silica fume and Class F fly ash, were used separately and together with normal portland cement to produce three concrete mixes in addition to the control mix. The properties of both fresh and hardened concretes were examined in the laboratory. The freshly mixed concrete mixes were tested for slump, slump flow, and V-funnel flow. The hardened concretes were tested for compressive strength and dynamic modulus of elasticity after exposing to 20, 35 and 50 °C. In addition, the initial surface absorption and the rate of moisture movement into the concretes were determined at 20 °C. The performance of the concretes in the fresh state was excellent due to their superior deformability and good segregation resistance. In their hardened state, the highest levels of compressive strength and dynamic modulus of elasticity were produced by silica fume concrete. In addition, silica fume concrete showed the lowest level of initial surface absorption and the lowest rate of moisture movement into the interior of concrete. In comparison, the compressive strength, dynamic modulus of elasticity, initial surface absorption, and moisture movement rate of silica fume-fly ash concrete were close to those of silica fume concrete. Moreover, all concretes provided relatively low compressive strength and dynamic modulus of elasticity when they were exposed to 50 °C. However, the effect of increased temperature was less detrimental for silica fume and silica fume-fly ash concretes in comparison with the control concrete.
The linear stability theory is applied to investigate the effects of rotation and feedback control on the onset of steady and oscillatory thermocapillary convection in a horizontal fluid layer heated from below with a free-slip bottom. The thresholds and codimension-2 points for the onset of steady and oscillatory convection are determined. The effect of feedback control on the parameter space dividing the steady and oscillatory convection regions is demonstrated.
The objective of this research is recovery of squalene from palm fatty acid distillate (PFAD) using supercritical fluid extraction (SFE). The extraction process was performed by using the SFE and recovered squalene was analyzed from total lipid extracts using HPLC. A central composite design was used to study the effect of SFE variables namely pressure (X₁) from 200 to 400 bar and temperature (X₂) from 40 to 60⁰C on the total lipid extracts (Y₁) and squalene concentration (Y₂) and optimize the SFE conditions. The nonlinear regression equations were significantly (p < 0.05) fitted for both responses with high R₂ (> 0.965), which had no indication of lack of fit. The results indicated that a combined pressure (200 bar) and temperature (50⁰C) was predicted to provide the optimum region in terms of total lipid extracts (13.84 ± 0.52%) and squalene concentration (418.31 ± 18.40 ppm) studied.
The sea cucumber (Stichopus vastus) is an underutilized species, as most of its parts, including the integument (high collagen content) are thrown away during processing. The aim of this study was to investigate the effects of different hydrolysis conditions (substrate to enzyme ratio (S/E), reaction temperature, and hydrolysis time) on the angiotensin I converting enzyme (ACE) inhibitory and radical scavenging (RSc) activities of the hydrolysates produced from trypsin hydrolysis of S. vastus collagen. Optimal conditions predicted by Box-Behnken Design modelling for producing ACE inhibitory and RSc hydrolysates were found to be S/E ratio (15), reaction temperature (55°C), and hydrolysis time (1 h). Under optimal conditions, ACE inhibitory and RSc activities were estimated to be as high as 67.8% and 77.9%, respectively. Besides, some novel bioactive peptides were identified through mass spectrometry analysis. These results indicate that S. vastus hydrolysates might be used as a functional ingredient in food and nutraceutical products.
Bioactive compounds from plant sources are generally categorized as natural antioxidants with well-known health benefits. The health-promoting characteristics of natural antioxidants include anti-inflammatory, anti-diabetic, and hepatic effects as well as free radical scavenging. Herein, a comprehensive and comparative review are presented about the effects of conventional (thermal and mechanical) and relatively new (non-thermal) processing methods on phytochemicals and discussed the importance of implementing the use of those methods that could be of very helpful retaining the quality of the bioactive compounds in plant-based foods. Plant-based foods rich in phenolics, vitamin C, carotenoids, and other compounds undergo a range of processing operations before they are consumed. Most of these methods involve thermal treatments of fruits, stems, leaves, and roots. These techniques have varying effects on bioactive compounds and their activities, and the magnitude of these effects depends on process parameters such as temperature, time, and the food matrix. Thermal processing can be detrimental to bioactive compounds while nonthermal procedures may not cause significant deterioration of important health-promoting phytochemicals and in some cases can improve their bio-activity and bio-availability. The detrimental effects of conventional processing on the quality of natural antioxidants have been compared to the effects of innovative nonthermal food treatments such as gamma and ultraviolet irradiation, ultraviolet light, pulsed electric fields, and high hydrostatic pressure.
The intake of heterocyclic amines is influenced by the amount and type of meat and fish ingested, frequency of consumption, cooking methods, cooking temperature, and duration of cooking. In this study, the dietary intake of heterocyclic amines in Malaysia and their main sources were investigated. Forty-two samples of meat and fish were analysed by high-performance liquid chromatography with photodiode array detector to determine the concentration of the six predominant heterocyclic amines, namely: 2-amino-3-methylimidazo[4,5-f] quinoline (IQ), 2-amino-3,4-dimethylimidazo[4,5-f] quinoline(MeIQ), 2-amino-3,8-dimethylimidazo[4,5-f] quinoxaline (MeIQx), 2-amino-3,4,8-trimethylimidazo[4,5-f] quinoxaline (4,8-DiMeIQx), 2-amino-3,7,8-trimethylimidazo[4,5-f] quinoxaline (7,8-DiMeIQx), and 2-amino-1-methyl-6-phenylimidazo[4,5-b]pyridine (PhIP). Dietary intake data were obtained using a food-frequency questionnaire when interviewing 600 Malaysian respondents. The level of total heterocyclic amines in food samples studies ranged from not detected to 38.7 ng g(-1). The average daily intake level of heterocyclic amine was 553.7 ng per capita day(-1). The intake of PhIP was the highest, followed by MeIQx and MeIQ. The results reveal that fried and grilled chicken were the major dietary source of heterocyclic amines in Malaysia. However, the heterocyclic amine intake by the Malaysian population was lower than those reported from other regions.
Matched MeSH terms: Hot Temperature/adverse effects*
The effects of flow rate, different pressures and temperatures on cocoa butter extracted from cocoa nib using supercritical carbon dioxide (scCO2) were investigated. The yield was analyzed for total fat content, triacylglycerol (TG) profile, and fatty acid (FA) profile. Extractions were carried out at pressures of 20 and 35 MPa, temperatures of 50 and 60 °C, and CO2 flow rates of 0.5, 1, 2, 4 mL min(-1). The result shows that the yield of cocoa butter extract increased with increasing pressure, temperature, and flow rate and the optimum conditions for the maximum cocoa butter extraction were 35 MPa, 60 °C and 2 mL min(-1), repectively. TGs and FAs were found to be similar in composition to those of cocoa butter obtained by conventional methods. The lower molecular weight TGs and FAs showed higher selectivity compared to higher molecular weight TGs and FAs.
Continuing trend in silicon wafer thickness directed at cost reduction approaches basic boundaries created by: (a) mismatch between Al paste and Si wafer thermal expansion and (b) incomplete optical absorption. With its symmetrical front and back electrical contacts, the bifacial solar cell setup reduces stress due to mismatch thermal expansion, decreases metal use and increases high temperature efficiency. Efficiency improvement is accomplished in bifacial solar cells by capturing light from the back surface. Partially transparent wafers provide an option to improve near-infrared radiation absorption within Si wafer. To fully absorb optical radiation, three-dimensional texture of these kinds of wafers is essential. Pulsed laser interactions, thermal oxidation, and wet chemical etching are included in this research. A feature of its energy and pattern setup is the interaction of pulsed laser with Si, running at 1.064 μm wavelength and micro-second length. Two experimental settings were explored: (a) post-laser chemical etching with potassium hydro-oxide etching with thermal oxide as etching mask and (b) post-laser heat Si surface oxidation. Due to fast melting and recrystallization, laser pulsed processing inherently produces its own texture. Some of these spherically-shaped, randomly focused characteristics improve inner scattering and boost near-infrared absorption within the wafer. These characteristics are separated during chemical etching with the thermally-grown oxide layer as an etch mask. Comparison of optical absorption in both surfaces shows almost a rise in the magnitude of absorption in non-etched surfaces. Detailed optical (optical microscope and IR absorption), morphological (field emission scanning electron microscope) and heat imaging (far IR camera) analyses were performed to comprehend physical processes that contribute to near-IR absorption improvement. Such kinds of partially-transparent, three-dimensional textured Si wafers are anticipated to discover applications for bifacial solar cells as substrates.
The computer, together with Lab View software, can be used as an automatic data acquisition system. This project deals with the development of a computer interfacing technique for the study of Hall Effect and converting the existing automation system into a Web-based automation system. The drive board RS 217-3611 with PCI 6025E card and stepper motor RS191-8340 with a resolution of 0.1mm, was used to move a pair of permanent magnets backward and forward against the sample. The General Interface Bus (GPIB) card interfaces, together with digital nano voltmeter and Tesla meter using serial port RS232 interface, are used for measuring the potential difference and magnetic field strength respectively. Hall Effect measurement on copper (Cu) and tantalum (Ta) showed negative and positive sign Hall coefficient. Therefore, the system has electron and hole charge carriers respectively at room temperature. The parameters such as drift velocity, conductivity, mobility, Hall Coefficient and charge carrier concentration were also automatically displayed on the front panel of Lab View programming and compared with standard value. The Web-based automation system can be remotely controlled and monitored by users in remote locations using only their web browsers. In addition, video conferencing through Net Meeting has been used to provide audio and video feedback to the client.
We report on a recycling project in which α-Al(2)O(3) was produced from aluminum cans because no such work has been reported in literature. Heated aluminum cans were mixed with 8.0 M of H(2)SO(4) solution to form an Al(2)(SO(4))(3) solution. The Al(2)(SO(4))(3) salt was contained in a white semi-liquid solution with excess H(2)SO(4); some unreacted aluminum pieces were also present. The solution was filtered and mixed with ethanol in a ratio of 2:3, to form a white solid of Al(2)(SO(4))(3)·18H(2)O. The Al(2)(SO(4))(3)·18H(2)O was calcined in an electrical furnace for 3 h at temperatures of 400-1400 °C. The heating and cooling rates were 10 °C /min. XRD was used to investigate the phase changes at different temperatures and XRF was used to determine the elemental composition in the alumina produced. A series of different alumina compositions, made by repeated dehydration and desulfonation of the Al(2)(SO(4))(3)·18H(2)O, is reported. All transitional alumina phases produced at low temperatures were converted to α-Al(2)O(3) at high temperatures. The X-ray diffraction results indicated that the α-Al(2)O(3) phase was realized when the calcination temperature was at 1200 °C or higher.
This study was conducted to develop an edible coating containing combined hydrophilic (chitosan) and hydrophobic (palm stearin) components which demonstrated gas barrier and moisture barrier properties, respectively, to prolong the post harvest life of star fruits (Averrhoa carambola L.). The emulsions of chitosan (C) and palm stearin (S) were prepared by using different ratios of C:S which were 1:0, 1:1, 1;2, 1:3, 2:1, 3:1 and 0:1. Viscosity of emulsions was studied. The physicochemical properties of coated star fruits were also evaluated in terms of weight loss, firmness, visual appearance, oxygen concentration, carbon dioxide concentration and ethylene concentration during storage at room temperature (26-28˚C) for 18 days. The results obtained showed that coating reduced weight loss, maintained firmness and appearance, slowed down the production of respiratory gases and reduced ethylene production. The most recommended coating for star fruits was C:S of 1:1 ratio as it showed good water barrier and gas barrier properties and could extend the post harvest life of star fruits up to 20 days as compared to the control samples which had a post harvest life of 12 days.
This study investigated the effect of annealing treatment (at 50°C for 72 h) on hydrolysis of tapioca and sweet potato starches using a raw starch hydrolyzing enzyme namely STARGEN 001 (a blend from fungal α-amylase and glucoamylase) at sub-gelatinization temperature (35°C) for 24 h. The degree of hydrolysis of the starches was evaluated based on the dextrose equivalent (DE) value. The hydrolyzed starches were then characterized in terms of its morphology, swelling power and solubility, gelatinization and pasting properties, amylose content and x-ray diffraction pattern. After 24 h of hydrolysis, annealed starches were hydrolyzed to a greater degree with higher DE value compared to native starches (40% vs 33% for tapioca; and 29% vs 24% for sweet potato starch). Scanning electron microscopy (SEM) micrographs revealed a more porous granules and rougher surface in annealed starches than their native counterparts. The swelling power and solubility of annealed starches decreased significantly. Annealing was found to affect the pasting properties of the starches appreciably and increase the starch gelatinization temperature. The amylose content in hydrolyzed annealed tapioca and sweet potato starches increased while no significant changes observed in the X-ray diffraction of those starches. This study shows that the annealing treatment can be used as a way to increase the degree of hydrolysis of tapioca and sweet potato starches at sub-gelatinization temperature using a raw starch hydrolyzing enzyme.
The production of carbon dioxide from Karas woods under argon atmosphere was investigated using a direct pyrolysis-combustion approach. Direct burning was used in this study, using argon for yrolysis and oxygen during combustion to look at the yield of carbon dioxide, produced at different parameters, such as the temperature, retention time and flow rate of argon, as the carrier gas. In this study, a new methodology, 23 response surface central composite design was successfully employed for the experimental design and analysis of results. Central composite experimental design and response surface method were utilized to determine the best operating condition for a maximum carbon dioxide production. Appropriate predictable empirical linear model was developed by incorporating interaction effects of all the variables involved. The results of the analysis revealed that linear equation models fitted well with the experimental for carbon dioxide yield. Nevertheless, the R-Squared obtained using the direct pyrolysis-combustion was 0.7118, indicating that the regression line was not at the best-fitted line.