Displaying publications 121 - 140 of 2911 in total

Abstract:
Sort:
  1. Gharehkhani S, Nouri-Borujerdi A, Kazi SN, Yarmand H
    ScientificWorldJournal, 2014;2014:504601.
    PMID: 25143981 DOI: 10.1155/2014/504601
    In this study an expression for soot absorption coefficient is introduced to extend the weighted-sum-of-gray gases data to the furnace medium containing gas-soot mixture in a utility boiler 150 MWe. Heat transfer and temperature distribution of walls and within the furnace space are predicted by zone method technique. Analyses have been done considering both cases of presence and absence of soot particles at 100% load. To validate the proposed soot absorption coefficient, the expression is coupled with the Taylor and Foster's data as well as Truelove's data for CO2-H2O mixture and the total emissivities are calculated and compared with the Truelove's parameters for 3-term and 4-term gray gases plus two soot absorption coefficients. In addition, some experiments were conducted at 100% and 75% loads to measure furnace exit gas temperature as well as the rate of steam production. The predicted results show good agreement with the measured data at the power plant site.
    Matched MeSH terms: Hot Temperature; Temperature
  2. Roslan R, Saleh H, Hashim I
    ScientificWorldJournal, 2014;2014:617492.
    PMID: 24991643 DOI: 10.1155/2014/617492
    The aim of the present numerical study is to analyze the conjugate natural convection heat transfer in a differentially heated square enclosure containing a conductive polygon object. The left wall is heated and the right wall is cooled, while the horizontal walls are kept adiabatic. The COMSOL Multiphysics software is applied to solve the dimensionless governing equations. The governing parameters considered are the polygon type, 3 ≤ N ≤ ∞, the horizontal position, 0.25 ≤ X 0 ≤ 0.75, the polygon size, 0 ≤ A ≤ π/16, the thermal conductivity ratio, 0.1 ≤ K r ≤ 10.0, and the Rayleigh number, 10(3) ≤ Ra ≤ 10(6). The critical size of the solid polygon was found exists at low conductivities. The heat transfer rate increases with the increase of the size of the solid polygon, until it reaches its maximum value. Here, the size of the solid polygon is reaches its critical value. Further, beyond this critical size of the solid polygon, will decrease the heat transfer rate.
    Matched MeSH terms: Hot Temperature*
  3. Khan A, Khan I, Ali F, Ulhaq S, Shafie S
    PLoS One, 2014;9(3):e90280.
    PMID: 24621775 DOI: 10.1371/journal.pone.0090280
    This study investigates the effects of an arbitrary wall shear stress on unsteady magnetohydrodynamic (MHD) flow of a Newtonian fluid with conjugate effects of heat and mass transfer. The fluid is considered in a porous medium over a vertical plate with ramped temperature. The influence of thermal radiation in the energy equations is also considered. The coupled partial differential equations governing the flow are solved by using the Laplace transform technique. Exact solutions for velocity and temperature in case of both ramped and constant wall temperature as well as for concentration are obtained. It is found that velocity solutions are more general and can produce a huge number of exact solutions correlative to various fluid motions. Graphical results are provided for various embedded flow parameters and discussed in details.
    Matched MeSH terms: Temperature*
  4. Gan CL, Hashim U
    Journal of electronic packaging, 2013 Jun;135(2):0210101-210107.
    PMID: 24891811
    Wearout reliability and high temperature storage life (HTSL) activation energy of Au and Pd-coated Cu (PdCu) ball bonds are useful technical information for Cu wire deployment in nanoscale semiconductor device packaging. This paper discusses the influence of wire type on the wearout reliability performance of Au and PdCu wire used in fine pitch BGA package after HTSL stress at various aging temperatures. Failure analysis has been conducted to identify the failure mechanism after HTSL wearout conditions for Au and PdCu ball bonds. Apparent activation energies (Eaa) of both wire types are investigated after HTSL test at 150 °C, 175 °C and 200 °C aging temperatures. Arrhenius plot has been plotted for each ball bond types and the calculated Eaa of PdCu ball bond is 0.85 eV and 1.10 eV for Au ball bond in 110 nm semiconductor device. Obviously Au ball bond is identified with faster IMC formation rate with IMC Kirkendall voiding while PdCu wire exhibits equivalent wearout and or better wearout reliability margin compare to conventional Au wirebond. Lognormal plots have been established and its mean to failure (t50) have been discussed in this paper.
    Matched MeSH terms: Hot Temperature; Temperature
  5. Balla HH, Abdullah S, Mohdfaizal W, Zulkifli R, Sopian K
    J Oleo Sci, 2013;62(7):533-9.
    PMID: 23823920
    A numerical simulation model for laminar flow of nanofluids in a pipe with constant heat flux on the wall was built to study the effect of the Reynolds number on convective heat transfer and pressure loss. The investigation was performed for hybrid nanofluids consisting of CuO-Cu nanoparticles and compared with CuO and Cu in which the nanoparticles have a spherical shape with size 50, 50, 50nm respectively. The nanofluids were prepared, following which the thermal conductivity and dynamic viscosity were measured for a range of temperatures (10 -60°C). The numerical results obtained were compared with the existing well-established correlation. The prediction of the Nusselt number for nanofluids agrees well with the Shah correlation. The comparison of heat transfer coefficients for CuO, Cu and CuO-Cu presented an increase in thermal conductivity of the nanofluid as the convective heat transfer coefficient increased. It was found that the pressure loss increases with an increase in the Reynolds number, nanoparticle density and particle volume fraction. However, the flow demonstrates enhancement in heat transfer which becomes greater with an increase in the Reynolds number for the nanofluid flow.
    Matched MeSH terms: Hot Temperature*
  6. Naganthran K, Nazar R, Pop I
    Sci Rep, 2016;6:24632.
    PMID: 27091085 DOI: 10.1038/srep24632
    In this paper, the unsteady stagnation-point boundary layer flow and heat transfer of a special third grade fluid past a permeable stretching/shrinking sheet has been studied. Similarity transformation is used to transform the system of boundary layer equations which is in the form of partial differential equations into a system of ordinary differential equations. The system of similarity equations is then reduced to a system of first order differential equations and has been solved numerically by using the bvp4c function in Matlab. The numerical solutions for the skin friction coefficient and heat transfer coefficient as well as the velocity and temperature profiles are presented in the forms of tables and graphs. Dual solutions exist for both cases of stretching and shrinking sheet. Stability analysis is performed to determine which solution is stable and valid physically. Results from the stability analysis depict that the first solution (upper branch) is stable and physically realizable, while the second solution (lower branch) is unstable.
    Matched MeSH terms: Hot Temperature; Temperature
  7. Ahmadian A, Bilal M, Khan MA, Asjad MI
    Sci Rep, 2020 Oct 13;10(1):17088.
    PMID: 33051520 DOI: 10.1038/s41598-020-74096-8
    The main feature of the present numerical model is to explore the behavior of Maxwell nanoliquid moving within two horizontal rotating disks. The disks are stretchable and subjected to a magnetic field in axial direction. The time dependent characteristics of thermal conductivity have been considered to scrutinize the heat transfer phenomena. The thermophoresis and Brownian motion features of nanoliquid are studied with Buongiorno model. The lower and upper disk's rotation for both the cases, same direction as well as opposite direction of rotation is investigated. The subsequent arrangement of the three dimensional Navier Stoke's equations along with energy, mass and Maxwell equations are diminished to a dimensionless system of equations through the Von Karman's similarity framework. The comparative numerical arrangement of modeled equations is further set up by built-in numerical scheme "boundary value solver" (Bvp4c) and Runge Kutta fourth order method (RK4). The various physical constraints, such as Prandtl number, thermal conductivity, magnetic field, thermal radiation, time relaxation, Brownian motion and thermophoresis parameters and their impact are presented and discussed briefly for velocity, temperature, concentration and magnetic strength profiles. In the present analysis, some vital characteristics such as Nusselt and Sherwood numbers are considered for physical and numerical investigation. The outcomes concluded that the disk stretching action opposing the flow behavior. With the increases of magnetic field parameter [Formula: see text] the fluid velocity decreases, while improving its temperature. We show a good agreement of the present work by comparing with those published in literature.
    Matched MeSH terms: Hot Temperature; Temperature
  8. Alaaeddin MH, Sapuan SM, Zuhri MYM, Zainudin ES, M Al-Oqla F
    Materials (Basel), 2019 Sep 17;12(18).
    PMID: 31533207 DOI: 10.3390/ma12183007
    Photovoltaic backsheets have considerable impact on the collective performance of solar cells. Material components should withstand certain temperatures and loads while maintaining high thermal stability under various weather conditions. Solar modules must demonstrate increased reliability, adequate performance, safety, and durability throughout the course of their lifetime. This work presents a novel solar module. The module consists of an innovative polyvinylidene fluoride-short sugar palm fiber (PVDF-SSPF) composite backsheet within its structure. It was electrically and thermally evaluated. The current-voltage characteristics (I-V) were obtained using the solar module analyzer, PROVA 210PV. A thermal evaluation was accomplished using a temperature device, SDL200. The thermal test consisted of two different assessments. The first targeted the surface and backsheet of the developed module to correlate their performance from within. The second assessment compared the thermal performance of the fabricated backsheet with the conventional one. Both tests were combined into a heatmap analysis to further understand the thermal performance. Results revealed that the developed module exhibited reasonable electrical efficiency, achieving appropriate and balanced I-V curves. PVDF-SSPF backsheets proved to be thermally stable by displaying less heat absorbance and better temperature shifts. Additional research efforts are highly encouraged to investigate other characteristics. To enhance performance, further analyses are needed such as the damp heat analysis, accelerated aging analysis, and heat dissipation phenomena.
    Matched MeSH terms: Hot Temperature; Temperature
  9. Akbari A, Mohammadian E, Alavi Fazel SA, Shanbedi M, Bahreini M, Heidari M, et al.
    ACS Omega, 2019 Apr 30;4(4):7038-7046.
    PMID: 31459815 DOI: 10.1021/acsomega.9b00176
    Many studies have investigated natural convection heat transfer from the outside surface of horizontal and vertical cylinders in both constant heat flux and temperature conditions. However, there are poor studies in natural convection from inclined cylinders. In this study, free convection heat transfer was examined experimentally from the outside surface of a cylinder for glycerol and water at various heat fluxes. The tests were performed at 10 different inclination angles of the cylinder, namely, φ = 0°, 10°, 20°, 30°, 40°, 50°, 60°, 70°, 80°, and 90°, measured from the horizon. Our results indicated that the average Nusselt number reduces with the growth in the inclination of the cylinder to the horizon at the same heat flux, and the average Nusselt number enhanced with the growth in heat flux at the same angle. Also, the average Nusselt number of water is greater than that of glycerol. A new experimental model for predicting the average Nusselt number is suggested, which has a satisfactory accuracy for experimental data.
    Matched MeSH terms: Hot Temperature; Temperature
  10. Azmirul Ashaari, Tahir Ahmad, Wan Munirah Wan Mohamad
    MATEMATIKA, 2018;34(2):235-244.
    MyJurnal
    Pressurized water reactor (PWR) type AP1000 is a third generation of a nuclear
    power plant. The primary system of PWR using uranium dioxide to generate heat energy
    via fission process. The process influences temperature, pressure and pH value of water
    chemistry of the PWR. The aim of this paper is to transform the primary system of PWR
    using fuzzy autocatalytic set (FACS). In this work, the background of primary system
    of PWR and the properties of the model are provided. The simulation result, namely
    dynamic concentration of PWR is verified against published data.
    Matched MeSH terms: Hot Temperature; Temperature
  11. Lim HP, Liew WYH, Melvin GJH, Jiang ZT
    Materials (Basel), 2021 Mar 29;14(7).
    PMID: 33805462 DOI: 10.3390/ma14071677
    This paper reviews the phase structures and oxidation kinetics of complex Ti-Al alloys at oxidation temperatures in the range of 600-1000 °C. The mass gain and parabolic rate constants of the alloys under isothermal exposure at 100 h (or equivalent to cyclic exposure for 300 cycles) is compared. Of the alloying elements investigated, Si appeared to be the most effective in improving the oxidation resistance of Ti-Al alloys at high temperatures. The effect of alloying elements on the mechanical properties of Ti-Al alloys is also discussed. Significant improvement of the mechanical properties of Ti-Al alloys by element additions has been observed through the formation of new phases, grain refinement, and solid solution strengthening.
    Matched MeSH terms: Hot Temperature; Temperature
  12. Lund LA, Omar Z, Khan I
    Heliyon, 2019 Mar;5(3):e01345.
    PMID: 30949601 DOI: 10.1016/j.heliyon.2019.e01345
    This study investigates the numerical solutions of MHD boundary layer and heat transfer of the Williamson fluid flow on the exponentially vertical shrinking sheet, having variable thickness and thermal conductivity under effects of the velocity and thermal slip parameters. It is also assumed that shrinking/stretching velocity, as well as the wall temperature, has the exponential function form. In this study, the continuity, momentum and energy equations with buoyancy parameter and Hartmann number are incorporated especially in the Williamson fluid flow case. Similarity transformation variables have been employed to formulate the ordinary differential equations (ODEs) from partial differential equations (PDEs). The resultant ODEs are solved by shooting method with Runge Kutta of fourth order method in Maple software. The effects of the different applied non-dimensional physical parameters on the boundary layer and heat transfer flow problems are presented in graphs. The effects of Williamson parameter, Prandtl number, and slip parameters on velocity and temperature profiles have been thoroughly demonstrated and discussed. The numerical results show that the buoyancy force and the slip parameters contribute to the occurrence of the dual solutions on the boundary layer and heat transfer flow problems. Furthermore, the stability analysis suggests that the first solution is stable and physically possible.
    Matched MeSH terms: Hot Temperature; Temperature
  13. Mishu MK, Rokonuzzaman M, Pasupuleti J, Shakeri M, Rahman KS, Binzaid S, et al.
    Sensors (Basel), 2021 Apr 08;21(8).
    PMID: 33917665 DOI: 10.3390/s21082604
    In this paper, an integrated thermoelectric (TE) and photovoltaic (PV) hybrid energy harvesting system (HEHS) is proposed for self-powered internet of thing (IoT)-enabled wireless sensor networks (WSNs). The proposed system can run at a minimum of 0.8 V input voltage under indoor light illumination of at least 50 lux and a minimum temperature difference, ∆T = 5 °C. At the lowest illumination and temperature difference, the device can deliver 0.14 W of power. At the highest illumination of 200 lux and ∆T = 13 °C, the device can deliver 2.13 W. The developed HEHS can charge a 0.47 F, 5.5 V supercapacitor (SC) up to 4.12 V at the combined input voltage of 3.2 V within 17 s. In the absence of any energy sources, the designed device can back up the complete system for 92 s. The sensors can successfully send 39 data string to the webserver within this time at a two-second data transmission interval. A message queuing telemetry transport (MQTT) based IoT framework with a customised smartphone application 'MQTT dashboard' is developed and integrated with an ESP32 Wi-Fi module to transmit, store, and monitor the sensors data over time. This research, therefore, opens up new prospects for self-powered autonomous IoT sensor systems under fluctuating environments and energy harvesting regimes, however, utilising available atmospheric light and thermal energy.
    Matched MeSH terms: Body Temperature; Temperature
  14. Parvizpour S, Hussin N, Shamsir MS, Razmara J
    Appl Microbiol Biotechnol, 2021 Feb;105(3):899-907.
    PMID: 33427934 DOI: 10.1007/s00253-020-11074-0
    Psychrophiles are cold-living microorganisms synthesizing enzymes that are permanently active at almost near-zero temperatures. Psychrozymes are supposed to be structurally more flexible than their homologous proteins. This structural flexibility enables these proteins to undergo conformational changes during catalysis and improve catalytic efficiency at low temperatures. The outstanding characteristics of the psychrophilic enzymes have attracted the attention of the scientific community to utilize them in a wide variety of industrial and pharmaceutical applications. In this review, we first highlight the current knowledge of the cold-adaptation mechanisms of the psychrophiles. In the sequel, we describe the potential applications of the enzymes in different biotechnological processes specifically, in the production of industrial and pharmaceutical products. KEY POINTS: • Methods that organisms have evolved to survive and proliferate at cold environments. • The economic benefits due to their high activity at low and moderate temperatures. • Applications of the psychrophiles in biotechnological and pharmaceutical industry.
    Matched MeSH terms: Cold Temperature; Temperature
  15. Thu BT, Van Minh T, Lim BP, Keng CL
    Trop Life Sci Res, 2011 Dec;22(2):37-43.
    PMID: 24575216
    Seeds of two selected clones of Artemisia annua L., TC1 and TC2, were germinated in a greenhouse. Four-week-old seedlings from both clones were grown in the Thù Đúc province of Ho Chi Minh City on 2(nd) January 2009 and Đà Lat on 20(th) January 2009. During this study period in Thù Đúc province, which is situated 4-5 m above sea level, was experiencing a tropical, dry season with temperatures ranging from 26.2°C-32.8°C. Đà Lat, situated at 1500-2000 m above sea level, was having temperate, dry season with lower temperatures, ranging from 10.5°C-18.0°C. The high temperatures and low elevation in Thù Đúc Province led to slow vegetative growth for all of the plants from the two different clones and the artemisinin contents were significantly reduced. The temperate environment of Đà Lat supported robustly growing plants, with plant heights and branch lengths 4-5 times taller and longer that those planted at Thù Đúc Province. The artemisinin contents of A. annua planted at Đà Lat were 3-4 times greater than those cultivated at Thù Đúc Province. Hence, this study indicated that the variations observed in plant growth and artemisinin contents were due to temperature effects because the two selected clones were genetically homogenous. The cold weather of Đà Lat was suitable for planting of A. annua as opposed to the tropical weather of Thù Đúc Province.
    Matched MeSH terms: Cold Temperature; Temperature
  16. Azmy MM, Hashim M, Numata S, Hosaka T, Noor NS, Fletcher C
    Sci Rep, 2016 08 26;6:32329.
    PMID: 27561887 DOI: 10.1038/srep32329
    General flowering (GF) is a unique phenomenon wherein, at irregular intervals, taxonomically diverse trees in Southeast Asian dipterocarp forests synchronize their reproduction at the community level. Triggers of GF, including drought and low minimum temperatures a few months previously has been limitedly observed across large regional scales due to lack of meteorological stations. Here, we aim to identify the climatic conditions that trigger large-scale GF in Peninsular Malaysia using satellite sensors, Tropical Rainfall Measuring Mission (TRMM) and Moderate Resolution Imaging Spectroradiometer (MODIS), to evaluate the climatic conditions of focal forests. We observed antecedent drought, low temperature and high photosynthetic radiation conditions before large-scale GF events, suggesting that large-scale GF events could be triggered by these factors. In contrast, we found higher-magnitude GF in forests where lower precipitation preceded large-scale GF events. GF magnitude was also negatively influenced by land surface temperature (LST) for a large-scale GF event. Therefore, we suggest that spatial extent of drought may be related to that of GF forests, and that the spatial pattern of LST may be related to that of GF occurrence. With significant new findings and other results that were consistent with previous research we clarified complicated environmental correlates with the GF phenomenon.
    Matched MeSH terms: Cold Temperature; Temperature
  17. Luqman Chuah, A., Russly A.R., Keshani, S.
    MyJurnal
    Rheology is the science of deformation and flow behavior of fluid. Knowledge of rheological properties of fluid foods and their variation with temperature and concentration have been globally important for industrialization of food technology for quality, understanding the texture, process engineering application, correlation with sensory evaluation, designing of transport system , equipment design (heat exchanger and evaporator ), deciding pump capacity and power requirement for mixing. The aim of this study was to determine the rheological behavior of pomelo juice at different concentrations (20-60.4%) and temperatures (23-60°C) by using a rotational rotational Haake Rheostress 600 rheometer. Pomelo juice was found to exhibit both Newtonian and Non-Newtonian behavior. For lower concentration the Newtonian behavior is observed while at higher concentration Non-Newtonian behavior was observed. Standard error (SE) method was selected on the basis to carry out the error analysis due to the best fit model. For the four models the values of SE show that the Herschel-Bulkley and Power Law models perform better than the Bingham and Casson models but Herschel-Bulkley model is true at higher concentration. The rheological model of pomelo juice, incorporating the effects of concentration and temperature was developed. The master-curve was investigated for comparing data from different products at a reference temperature of 40°C. Multiple regression analysis indicated Master-Curve presents good agreement for pomelo juice at all concentrations studied with R2>0.8.
    Matched MeSH terms: Hot Temperature; Temperature
  18. Farzanmanesh, Raheleh, Ahmad Makmom Abdullah, Shakiba, Alireza, Jamil Amanollahi
    MyJurnal
    Iran is situated in a very diverse environmental area. The climate of the region is varied and influencedby different patterns. In order to best describe the expected climate change impacts for the region,climate change scenarios and climate variables must be developed on a regional, or even site-specific,scale. The weather generator is one of the valid downscaling methods. In the current study, LARSWG(a weather generator) and the outputs from ECHO-G for present climate, as well as future timeslice of 2010-2039 based on A1 scenario, were used to evaluate LARS-WG as a tool at 13 synopticstations located in the north and northeast parts of Iran. The results obtained in this study illustratethat LARS-WG has a reasonable capability of simulating the minimum and maximum temperaturesand precipitation. In addition, the results showed that the mean precipitation decreased in Semnan, thesouth of Khorasan and Golestan. Meanwhile, the mean temperature during 2010-2039 would increaseby 0.5°C, especially in the cold season.
    Matched MeSH terms: Cold Temperature; Temperature
  19. Esro M, Kolosov O, Jones PJ, Milne WI, Adamopoulos G
    ACS Appl Mater Interfaces, 2017 01 11;9(1):529-536.
    PMID: 27933760 DOI: 10.1021/acsami.6b11214
    Silicon dioxide (SiO2) is the most widely used dielectric for electronic applications. It is usually produced by thermal oxidation of silicon or by using a wide range of vacuum-based techniques. By default, the growth of SiO2 by thermal oxidation of silicon requires the use of Si substrates whereas the other deposition techniques either produce low quality or poor interface material and mostly require high deposition or annealing temperatures. Recent investigations therefore have focused on the development of alternative deposition paradigms based on solutions. Here, we report the deposition of SiO2 thin film dielectrics deposited by spray pyrolysis in air at moderate temperatures of ≈350 °C from pentane-2,4-dione solutions of SiCl4. SiO2 dielectrics were investigated by means of UV-vis absorption spectroscopy, spectroscopic ellipsometry, XPS, XRD, UFM/AFM, admittance spectroscopy, and field-effect measurements. Data analysis reveals smooth (RRMS < 1 nm) amorphous films with a dielectric constant of about 3.8, an optical band gap of ≈8.1 eV, leakage current densities in the order of ≈10(-7) A/cm(2) at 1 MV/cm, and high dielectric strength in excess of 5 MV/cm. XPS measurements confirm the SiO2 stoichiometry and FTIR spectra reveal features related to SiO2 only. Thin film transistors implementing spray-coated SiO2 gate dielectrics and C60 and pentacene semiconducting channels exhibit excellent transport characteristics, i.e., negligible hysteresis, low leakage currents, high on/off current modulation ratio on the order of 10(6), and high carrier mobility.
    Matched MeSH terms: Temperature*
  20. Cheng-Yong H, Yun-Ming L, Abdullah MM, Hussin K
    Sci Rep, 2017 03 27;7:45355.
    PMID: 28345643 DOI: 10.1038/srep45355
    This paper presents a comparative study of the characteristic of unfoamed and foamed geopolymers after exposure to elevated temperatures (200-800 °C). Unfoamed geopolymers were produced with Class F fly ash and sodium hydroxide and liquid sodium silicate. Porous geopolymers were prepared by foaming with hydrogen peroxide. Unfoamed geopolymers possessed excellent strength of 44.2 MPa and degraded 34% to 15 MPa in foamed geopolymers. The strength of unfoamed geopolymers decreased to 5 MPa with increasing temperature up to 800 °C. Foamed geopolymers behaved differently whereby they deteriorated to 3 MPa at 400 °C and increased up to 11 MPa at 800 °C. Even so, the geopolymers could withstand high temperature without any disintegration and spalling up to 800 °C. The formation of crystalline phases at higher temperature was observed deteriorating the strength of unfoamed geopolymers but enhance the strength of foamed geopolymers. In comparison, foamed geopolymer had better thermal resistance than unfoamed geopolymers as pores provide rooms to counteract the internal damage.
    Matched MeSH terms: Hot Temperature; Temperature
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links