Pretreatment of the high free fatty acid rubber seed oil (RSO) via esterification reaction has been investigated by using a pilot scale hydrodynamic cavitation (HC) reactor. Four newly designed orifice plate geometries are studied. Cavities are induced by assisted double diaphragm pump in the range of 1-3.5 bar inlet pressure. An optimised plate with 21 holes of 1mm diameter and inlet pressure of 3 bar resulted in RSO acid value reduction from 72.36 to 2.64 mg KOH/g within 30 min of reaction time. Reaction parameters have been optimised by using response surface methodology and found as methanol to oil ratio of 6:1, catalyst concentration of 8 wt%, reaction time of 30 min and reaction temperature of 55°C. The reaction time and esterified efficiency of HC was three fold shorter and four fold higher than mechanical stirring. This makes the HC process more environmental friendly.
Crude oil pollution is one of the most serious environmental issues today, and the clean-up procedure is perhaps the most difficult. Within one to three weeks, the vast majority of oil bacteria may degrade approximately 60% of the crude oil, leaving approximately 40% intact. The by-product metabolites produced during the breakdown of oil are essentially organic molecules in nature. These metabolites inhibit its enzymes, preventing the oil bacteria from further degrading the oil. By combining a variety of different oils with heterotrophic bacteria in a bioreactor, the rate of crude oil biodegradation was accelerated. In this study, two strains of oil-resistant, heterotrophic bacteria (OG1 and OG2-Erythrobacter citreus) and a bacterium that uses hydrocarbons (AR3-Pseudomonas pseudoalcaligenes) were used. Gas chromatography-mass spectroscopy was used to investigate the effectiveness of this consortium of symbiotic bacteria in the biodegradation of crude oil. According to gravimetric and gas chromatography analyses, the consortium bacteria digested 69.6% of the crude oil in the bioreactor, while the AR3 single strain was only able to destroy 61.9% of it. Under the same experimental conditions, consortium bacteria degraded approximately 84550.851 ppb (96.3%) of 16 aliphatic hydrocarbons and 9333.178 ppb (70.5%) of 16 aromatic hydrocarbons in the bioreactor. It may be inferred that the novel consortium of symbiotic bacteria accelerated the biodegradation process and had great potential for use in increasing the bioremediation of hydrocarbon-contaminated locations.
This study analyzes the impact of ASEAN's goal of achieving carbon neutrality by 2050 on climate change and coastal ecosystems by examining carbon emissions and energy usage from 2019 to 2050 using different scenarios to reduce emissions and meet global temperature goals. This research proposes strategies to reduce carbon emissions and mitigate climate change effects on coastal ecosystems, focusing on evaluating CO2 emissions from ASEAN's coastal shipping sector. Geospatial data was used to analyze ship activity and develop carbon neutrality strategies. Various sources are used to gather data, including the Maritime Portal, exact Earth AIS, FASA and GFW. This study finds that container ships emitted 13.7 × 106 t of CO2 in 2019, with the transportation sector contributing 3.8% of the total greenhouse gas in 2020. Without regulations, CO2 emissions could increase fourfold by 2050. The study recommends implementing policies such as adopting clean fuels, energy efficiency standards and fuel-related regulations to reduce CO2 emissions by 65-80% by 2050. It also emphasizes the importance of cleaner technologies, regulatory considerations and collaboration, which would have positive implications for coastal ecosystems. This study is beneficial to professionals in the maritime and shipping industries, policy makers, environmental consultants, sustainability specialists, and international organizations.
Chemical interesterification of rubber seed oil has been investigated for four different designed orifice devices in a pilot scale hydrodynamic cavitation (HC) system. Upstream pressure within 1-3.5bar induced cavities to intensify the process. An optimal orifice plate geometry was considered as plate with 1mm dia hole having 21 holes at 3bar inlet pressure. The optimisation results of interesterification were revealed by response surface methodology; methyl acetate to oil molar ratio of 14:1, catalyst amount of 0.75wt.% and reaction time of 20min at 50°C. HC is compared to mechanical stirring (MS) at optimised values. The reaction rate constant and the frequency factor of HC were 3.4-fold shorter and 3.2-fold higher than MS. The interesterified product was characterised by following EN 14214 and ASTM D 6751 international standards.
Biomedical waste from healthcare activities poses a higher hazard of infection and damage than other types of trash. The main objective of the study was to assess the awareness knowledge and practices of biomedical waste management (BMWM) among health care professionals in the health care units. The cross-sectional study was carried out to access the awareness, knowledge and practices of health care professionals for BMWM. Using a qualitative approach, the study was escorted in two Apex hospitals i.e. the Allied Hospital and the District Head Quarter Hospital, Faisalabad, Pakistan from August 5, 2019 to October 15, 2019. More than 90% of respondents knew the phrase BMWM, but just 35.4% had awareness about biomedical waste regulations. About 71.6% of the respondents were familiar with biomedical waste's color-coding segregation. The study concludes gap in the awareness, knowledge and practices for BMWM. The sanitary workers of the hospitals had no knowledge about BMWM and the BMWM/healthcare waste management rule 2005 established in Pakistan due to the lack of training regarding waste management and the segregation process. Some of the staff members were aware of the BMWM practices under the rules and regulations of Pakistan but were unable to implement at their work place. It is necessary to dispose of the biomedical waste according to the established terms and conditions of BMWM rules (2005) of Pakistan. Weak structure of BMWM was observed at the study sites due to the lack of training, liabilities and absence of penalties against improper biomedical waste disposal as violation of the rules and regulations. It's a dire need of the time to consider the biomedical waste as hazardous waste and make policies for its safe disposal and ensure the implementation of the policies in all the medical centers of Pakistan.
The International Maritime Organization has set a goal to achieve a 50% reduction of total annual greenhouse gas emission related to the international shipping by 2050 compared to the 2008 baseline emissions. Malaysia government has taken an initiative to investigate the assessment (cost-effectiveness) of this International Maritime Organization's short-term measure on Malaysian-registered domestic ships although this measure is only for international merchant ship. To achieve this, this paper collected the ship's data from the shipowners from 25 sample ships. Engine power limitation is the most cost-effective option, but low power limits can lead to substantially increased sailing times. Based on cost-efficiency analysis, it creates for the purpose of compliance with the operational carbon intensity indicator. It found that even if it is possible to bring an asset back into service, it may not be possible to do so in a manner that generates a profit or complies with applicable regulations. In these situations, it may be more prudent to scrap the asset rather than run the risk of having it become a stranded asset. This is especially true for older tankers. Alternatives with lengthy payback periods are not desirable for the domestic tanker fleet that is already in operation.
Ecosystem functions directly depend upon biophysical as well as biogeochemical reactions occurring at the soil-microbe-plant interface. Environment is considered as a major driver of any ecosystem and for the distributions of living organisms. Any changes in climate may potentially alter the composition of communities i.e., plants, soil microbes and the interactions between them. Since the impacts of global climate change are not short-term, it is indispensable to appraise its effects on different life forms including soil-microbe-plant interactions. This article highlights the crucial role that microbial communities play in interacting with plants under environmental disturbances, especially thermal and water stress. We reviewed that in response to the environmental changes, actions and reactions of plants and microbes vary markedly within an ecosystem. Changes in environment and climate like warming, CO2 elevation, and moisture deficiency impact plant and microbial performance, their diversity and ultimately community structure. Plant and soil feedbacks also affect interacting species and modify community composition. The interactive relationship between plants and soil microbes is critically important for structuring terrestrial ecosystems. The anticipated climate change is aggravating the living conditions for soil microbes and plants. The environmental insecurity and complications are not short-term and limited to any particular type of organism. We have appraised effects of climate change on the soil inhabiting microbes and plants in a broader prospect. This article highlights the unique qualities of tripartite interaction between plant-soil-microbe under climate change.
Cellulose is the most abundant polysaccharide on earth. It has a large number of desirable properties. Its low toxicity makes it more useful for a variety of applications. Nowadays, its composites are used in most engineering fields. Composite consists of a polymer matrix and use as a reinforcing material. By reducing the cost of traditional fibers, it has an increasing demand for environment-friendly purposes. The use of these types of composites is inherent in moisture absorption with hindered natural fibers. This determines the reduction of polymer composite material. By appropriate chemical surface treatment of cellulose composite materials, the effect could be diminished. The most modern and advanced techniques and methods for the preparation of cellulose and polymer composites are discussed here. Cellulosic composites show a reinforcing effect on the polymer matrix as pointed out by mechanical characterization. Researchers tried their hard work to study different ways of converting various agricultural by-products into useful eco-friendly polymer composites for sustainable production. Cellulose plays building blocks, that are critical for polymer products and their engineering applications. The most common method used to prepare composites is in-situ polymerization. This help to increase the yields of cellulosic composites with a significant enhancement in thermal stability and mechanical properties. Recently, cellulose composites used as enhancing the incorporation of inorganic materials in multi-functional properties. Furthermore, we have summarized in this review the potential applications of cellulose composites in different fields like packaging, aerogels, hydrogels, and fibers.
Employing aerobic fermentation, Gram-negative bacteria belonging to the genus Xanthomonas produce the high molecular weight natural heteropolysaccharide known as xanthan. It has various amounts of O-acetyl and pyruvyl residues together with D-glucosyl, D-mannosyl, and D-glucuronyl acid residues in a molar ratio of 2:2:1. The unique structure of xanthan allowed its various applications in a wide range of industries such as the food industry, pharmacology, cosmetics and enhanced oil recovery primarily in petroleum. The cultivation medium used in the manufacture of this biopolymer is critical. Many attempts have been undertaken to generate xanthan gum from agro-based and food industry wastes since producing xanthan gum from synthetic media is expensive. Optimal composition and processing parameters must also be considered to achieve an economically viable manufacturing process. There have been several attempts to adjust the nutrient content and feeding method, temperature, pH, agitation and the use of antifoam in xanthan fermentations. Various modifications in technological approaches have been applied to enhance its physicochemical properties which showed significant improvement in the area studied. This review describes the biosynthesis production of xanthan with an emphasis on the importance of the upstream processes involving medium, processing parameters, and other factors that significantly contributed to the final application of this precious polysaccharide.
Coastal ecosystems are facing heightened risks due to human-induced climate change, including rising water levels and intensified storm events. Accurate bathymetry data is crucial for assessing the impacts of these threats. Traditional data collection methods can be cost-prohibitive. This study investigates the feasibility of using freely accessible Landsat and Sentinel satellite imagery to estimate bathymetry and its correlation with hydrographic chart soundings in Port Klang, Malaysia. Through analysis of the blue and green spectral bands from the Landsat 8 and Sentinel 2 datasets, a bathymetry map of Port Klang's seabed is generated. The precision of this derived bathymetry is evaluated using statistical metrics like Root Mean Square Error (RMSE) and the coefficient of determination. The results reveal a strong statistical connection (R2 = 0.9411) and correlation (R2 = 0.7958) between bathymetry data derived from hydrographic chart soundings and satellite imagery. This research not only advances our understanding of employing Landsat imagery for bathymetry assessment but also underscores the significance of such assessments in the context of climate change's impact on coastal ecosystems. The primary goal of this research is to contribute to the comprehension of Landsat imagery's utility in bathymetry evaluation, with the potential to enhance safety protocols in seaport terminals and provide valuable insights for decision-making concerning the management of coastal ecosystems amidst climate-related challenges. The findings of this research have practical implications for a wide range of stakeholders involved in coastal management, environmental protection, climate adaptation and disaster preparedness.
Industrial revolution on the back of fossil fuels has costed humanity higher temperatures on the planet due to ever-growing concentration of carbon dioxide emissions in Earth's atmosphere. To tackle global warming demand for renewable energy sources continues to increase. Along renewables, there has been a growing interest in converting carbon dioxide to methanol, which can be used as a fuel or a feedstock for producing chemicals. The current review study provides a comprehensive overview of the recent advancements, challenges and future prospects of methanol production and purification via membrane-based technology. Traditional downstream processes for methanol production such as distillation and absorption have several drawbacks, including high energy consumption and environmental concerns. In comparison to conventional technologies, membrane-based separation techniques have emerged as a promising alternative for producing and purifying methanol. The review highlights recent developments in membrane-based methanol production and purification technology, including using novel membrane materials such as ceramic, polymeric and mixed matrix membranes. Integrating photocatalytic processes with membrane separation has been investigated to improve the conversion of carbon dioxide to methanol. Despite the potential benefits of membrane-based systems, several challenges need to be addressed. Membrane fouling and scaling are significant issues that can reduce the efficiency and lifespan of the membranes. The cost-effectiveness of membrane-based systems compared to traditional methods is a critical consideration that must be evaluated. In conclusion, the review provides insights into the current state of membrane-based technology for methanol production and purification and identifies areas for future research. The development of high-performance membranes and the optimization of membrane-based processes are crucial for improving the efficiency and cost-effectiveness of this technology and for advancing the goal of sustainable energy production.
Plastics are still the most popular food packaging material and many of them end up in the environment for a long period. Due to packaging material's inability to inhibit microbial growth, beef often contains microorganisms that affect its aroma, colour and texture. Cinnamic acid is categorized as generally recognised as safe and is permitted for use in food. The development of biodegradable food packaging film with cinnamic acid has never been conducted before. This present study was aimed to develop a biodegradable active packaging material for fresh beef using sodium alginate and pectin. The film was successfully developed with solution casting method. The films' thickness, colour, moisture level, dissolution, water vapour permeability, bending strength and elongation at break were comparable to those of polyethylene plastic film in terms of these attributes. The developed film also showed the degradability in soil of 43.26% in a duration of 15 days. Fourier Transform Infrared (FTIR) spectra showed that cinnamic acid was successfully incorporated with the film. The developed film showed significant inhibitory activity on all test foodborne bacteria. On Hohenstein challenge test, a 51.28-70.45% reduction on bacterial growth was also observed. The antibacterial efficacy of the established film by using fresh beef as food model. The meats wrapped with the film showed significant reduction in bacterial load throughout the experimental period by 84.09%. The colour of the beef also showed significant different between control film and edible film during 5 days test. Beef with control film turned into dark brownish and beef with cinnamic acid turn into light brownish. Sodium alginate and pectin film with cinnamic acid showed good biodegradability and antibacterial activity. Further studies can be conducted to investigate the scalability and commercial viability of this environmental-friendly food packaging materials.
Coastal ecosystems play an important part in mitigating the effects of climate change. Coastal ecosystems are becoming more susceptible to climate change impacts due to human activities and maritime accidents. The global shipping industry, especially in Southeast Asia, has witnessed numerous accidents, particularly involving passenger ferries, resulting in injuries and fatalities in recent years. In order to mitigate the impact of climate change on coastal ecosystems, this study aimed to evaluate the relationship between employees' perceptions of safety criteria and their own safety behaviour on Langkawi Island, Malaysia. A straightforward random sampling technique was employed to collect data from 112 ferry employees aboard Malaysian-registered passenger boats by administering questionnaires. The findings shed light on the strong connection between providing safety instructions for passengers and safety behaviour among ferry workers. Safety instructions should contain climate-related information to successfully address the effects of climate change. The instructions might include guidance on responding to extreme weather events and understanding the potential consequences of sea-level rise on coastal communities. The ferry company staff should also expand their safe behaviour concept to include training and preparation for climate-related incidents. The need to recognise the interconnectedness between climate change, ferry safety and the protection of coastal ecosystems is emphasised in this study. The findings can be utilised by policymakers, regulatory agencies and ferry operators to design holistic policies that improve safety behaviour, minimise maritime mishaps and preserve the long-term sustainability of coastal ecosystems in the face of difficulties posed by climate change.
Recent advancement in biophotovoltaic systems using microalgae, coupled with biorefinery approach, would improve economy-feasibility in production. The major concern is its commercial strength in terms of scalability, strain selection and extraction procedure cost. It must compete with conventional feedstocks such as fossil fuels. This project proposes to enhance the economic feasibility of microalgae-based biorefinery by evaluating their performance for bio-electricity, bio-diesel and carotenoids production in a single cycle. The first part of the study was to construct and select a Bio-bottle Voltaic (BBV) device that would allow microalgae to grow and produce bioproducts, as well as generate the maximum current output reading derived from the microalgae's photosynthesis process. The second phase consisted of a 25-day investigation into the biorefinery performance of six different microalgal species in producing bio-electricity, bio-diesel and carotenoid in a prototype BBV device. The prototype BBV device with aluminium foil and pencil lead as its anode and cathode produced the highest carotenoid and biodiesel component production from the two microalgae tested, according to the results of the first phase of the experiment. In the second portion of the study, Scenedesmus dimorphus and Chlorella vulgaris were identified as the two microalgae most capable of maintaining their growth throughout the experiment. The maximum current reading observed for C. vulgaris was 653 mV. High Performance Liquid Chromatography analysis showed four major carotenoid compounds found which were Neoxanthin, Cantaxanthin, Astaxanthin and 9-cis antheraxanthin, and the highest carotenoid producer was C. vulgaris which recorded at 1.73 μg/mL. C. vulgaris recorded as the most alkanes producer with 22 compounds detected and Heptacosane and Heneicosane as the two major biodiesel compounds found in the extracts. Evaluation of C. vulgaris data showed that it has enormous potential for microalgal biorefinery candidates. Further ongoing research and development efforts for C. vulgaris will improve the economic viability of microalgae-based industries and reduce reliance on depleted fossil fuels.
Crucial to the Earth's oceans, ocean currents dynamically react to various factors, including rotation, wind patterns, temperature fluctuations, alterations in salinity and the gravitational pull of the moon. Climate change impacts coastal ecosystems, emphasizing the need for understanding these currents. This study explores multibeam echo sounder (MBES), specifically R2-Sonic 2020, offering detailed seabed information. Investigating coral reefs, rocky reefs and artificial reefs aimed to map seafloor currents movement and their climate change responses. MBES data study explores multibeam echo sounder (MBES), specifically R2-Sonic 2020, offering detailed seabed information. Investigating coral reefs, rocky reefs and artificial reefs aimed to map seafloor currents movement and their climate change responses. MBES data viz. Bathymetry and backscatter were classified and acoustic doppler current profiler (ADCP) ground data were validated using random forest regression. Results indicated high precision in currents speed measurement i.e. coral reefs with 0.96, artificial reefs with 0.94 and rocky reefs with 0.97. Currents direction accuracy was notable in coral reefs with 0.85, slightly lower in rocky reefs with 0.72 and artificial reefs with 0.60. Random forest identified sediment and backscatter as key for speed prediction while direction relies on bathymetry, slope and aspect. The study emphasizes integrating sediment size, backscatter, bathymetry and ADCP data for seafloor current analysis. This multibeam data on sediments and currents support better marine spatial planning and determine biodiversity patterns planning in the reef area.
This study is based on the removal of methylene blue (MB) from aqueous solution by cost effective and biodegradable adsorbent carboxymethyl starch grafted polyvinyl pyrolidone (Car-St-g-PVP). The Car-St-g-PVP was synthesized by grafting vinyl pyrolidone onto carboxymethyl starch by free radical polymerization reaction. The structure and different properties of Car-St-g-PVP were determined by 1H NMR, FT-IR, XRD, TGA and SEM. A series of batch experiments were conducted for the removal of MB, The adsorption affecting factors such as temperature, contact time, initial concentration of MB dye, dose of Car-St-g-PVP and pH were studied in detail. The other parameters like the thermodynamic study, kinetics and isothermal models were fitted to the experimental data. The results showed that pseudo 2nd order kinetics and Langmuir's adsorption isotherms were best fitted to experimental data with regression coefficient R2 viz. 0.99 and 0.97. The kinetic study showed that the adsorption mechanism favored chemisorption. The Gibbs free energy (ΔG°) for the adsorption process was found to be -7.31 kJ/mol, -8.23 kJ/mol, -9.00 kJ/mol and -10.10 kJ/mol at 25 °C, 35 °C, 45 °C and 55 °C respectively. The negative values of ΔG° suggested the spontaneous nature of the adsorption process. Similarly, the positive values of entropy (ΔS°) and enthalpy (ΔH°) 91.27 J/k.mol and 19.90 kJ/mol showed the increasing randomness and endothermic nature of the adsorption process. The value of separation factor (RL) was found to be less than one (RL
The critical challenge being faced by our current modern society on a global scale is to reduce the surging effects of climate change and global warming, being caused by anthropogenic emissions of CO2 in the environment. Present study reports the surface driven adsorption potential of deep eutectic solvents (DESs) surface functionalized cerium oxide nanoparticles (CeNPs) for low pressure CO2 separation. The phosphonium based DESs were prepared using tetra butyl phosphoniumbromide as hydrogen bond acceptor (HBA) and 6 acids as hydrogen bond donors (HBDs). The as-developed DESs were characterized and employed for the surface functionalization of CeNPs with their subsequent utilization in adsorption-based CO2 adsorption. The synthesis of as-prepared DESs was confirmed through FTIR measurements and absence of precipitates, revealed through visual observations. It was found that DES6 surface functionalized CeNPs demonstrated 27% higher adsorption performance for CO2 capturing. On the contrary, DES3 coated CeNPs exhibited the least adsorption progress for CO2 separation. The higher adsorption performance associated with DES6 coated CeNPs was due to enhanced surface affinity with CO2 molecules that must have facilitated the mass transport characteristics and resulted an enhancement in CO2 adsorption performance. Carboxylic groups could have generated an electric field inside the pores to attract more polarizable adsorbates including CO2, are responsible for the relatively high values of CO2 adsorption. The quadruple movement of the CO2 molecules with the electron-deficient and pluralizable nature led to the enhancement of the interactive forces between the CO2 molecules and the CeNPs decorated with the carboxylic group hydrogen bond donor rich DES. The current findings may disclose the new research horizons and theoretical guidance for reduction in the environmental effects associated with uncontrolled CO2 emission via employing DES surface coated potential CeNPs.
Epoxy resins are important thermosetting polymers. They are widely used in many applications i.e., adhesives, plastics, coatings and sealers. Epoxy molding compounds have attained dominance among common materials due to their excellent mechanical properties. The sol-gel simple method was applied to distinguish the impact on the colloidal time. The properties were obtained with silica-based fillers to enable their mechanical and thermal improvement. The work which we have done here on epoxy-based nanocomposites was successfully modified. The purpose of this research was to look into the effects of cellulose nanocrystals (CNCs) on various properties and applications. CNCs have recently attracted a lot of interest in a variety of industries due to their high aspect ratio, and low density which makes them perfect candidates. Adding different amounts of silica-based nanocomposites to the epoxy system. Analyzed with different techniques such as Fourier-transformed infrared spectroscope (FTIR), thermogravimetric analysis (TGA) and scanning electronic microscopic (SEM) to investigate the morphological properties of modified composites. The various %-age of silica composite was prepared in the epoxy system. The 20% of silica was shown greater enhancement and improvement. They show a better result than D-400 epoxy. Increasing the silica, the transparency of the films decreased, because clustering appears. This shows that the broad use of CNCs in environmental engineering applications is possible, particularly for surface modification, which was evaluated for qualities such as absorption and chemical resistant behavior.
Vancomycin is the last resort antibiotic for the treatment of severe bacterial keratitis. Its clinical application is limited due to its hydrophilicity and high molecular weight. To overcome this, this study aims to develop nanoparticles-laden contact lens for controlled ocular delivery of vancomycin. Polyvinyl alcohol (PVA) was used as encapsulant material. The nanoparticles had a negative surface charge and an average size of 147.6 nm. A satisfactory encapsulation efficiency (61.24%) was obtained. The release profile was observed to be slow and sustained, with a release rate of 1.29 μL mg-1 h-1 for 48 h. Five out of 6 test bacteria were suppressed by vancomycin nanoparticles-laden contact lens. Vancomycin is generally ineffective against Gram-negative bacteria and unable to pass through the outer membrane barrier. In this study, vancomycin inhibited Proteus mirabilis and Pseudomonas aeruginosa. Nano-encapsulation enables vancomycin to penetrate the Gram-negative cell wall and further destroy the bacterial cells. On Hohenstein challenge test, all test bacteria exhibited significant reduction in growth when exposed to vancomycin nanoparticles-laden contact lens. This study created an effective and long-lasting vancomycin delivery system via silicone hydrogel contact lenses, by using PVA as encapsulant. The antibiotic efficacy and vancomycin release should be further studied using ocular in vivo models.
It is essential to investigate the physicochemical and thermal properties of choline chloride (ChCl)-based deep eutectic solvents (DESs) as hydrogen bond acceptor (HBA) with various hydrogen bond donor (HBD) functional groups, such as α-hydroxy acid (lactic acid) or polyol (glycerol). It is important to consider how molar ratios impact these properties, as they may be altered for particular applications. This study aimed to examine the physicochemical and thermal properties of ChCl-based DESs with lactic acid (LA) or glycerol (Gly) at different molar ratios (1:2-1:10). The pH of ChCl:LA (0-1.0) is lower than that of ChCl:Gly (4.0-5.0) because of the hydrogen bonds between ChCl and LA. A higher amount of LA/Gly resulted in higher densities of ChCl:Gly (1.20-1.22 g cm-3) and ChCl:LA (1.16-1.19 g cm-3) due to the stronger hydrogen bonds and tighter packing of the molecules. The refractive index of ChCl:Gly (1.47-1.48) was higher than ChCl:LA (1.44-1.46), with a trend similar to density. The viscosities of ChCl:Gly (0.235-0.453 Pa s) and ChCl:LA (0.04-0.06 Pa s) increased with increasing LA/Gly molar ratio but decreased with temperature due to the high kinetic energy from heating, lowering the attractive forces between molecules. The activation energy for ChCl:LA (15.29-15.55 kJ mol-1) is greater than for ChCl:Gly (7.77-8.78 kJ mol-1), indicating that ChCl:LA has a greater viscosity-temperature dependence than ChCl:Gly. The DESs decomposition temperatures are 179.73-192.14 °C for ChCl:LA and 189.69-197.41 °C for ChCl:Gly. Freezing temperatures are correlated with the molecular weight of HBDs, with lower values causing a larger decrease in freezing temperatures. The interactions of polyols with anions were stronger than those of α-hydroxy acids with anions. The variations in HBA to HBD molar ratios affected DESs properties, providing a fundamental understanding of the properties critical for their diverse applications.