In this report, we demonstrate that continuous improvement in XPS instruments and the calibration standards as well
as analysis with standard component-fitting procedures can be used to determine the binding energies of compounds
containing phosphorus and sulfur of different oxidation states with higher confidence. Based on such improved XPS
analyses, the binding energies (BEs) of S2p signals for sulfur of increasing oxidation state are determined to be 166-167.5
eV for S=O in dimethyl sulfoxide, 168.1 eV for S=O2
in polysulfone, 168.4 eV for SO3
in polystyrene sulfonate and 168.8
eV for SO4
in chondroitin sulfate. The BEs of P2p signals show the following values: 132.9 eV for PO3
in triisopropyl
phosphite, 133.3 eV for PO4
in glycerol phosphate, 133.5 eV for PO4
in sodium tripolyphosphate and 134.0 eV for PO4
in sodium hexametaphosphate. These results showed that there are only small increases in the binding energy when
additional oxygen atoms are added to the S-O chemical group. A similar result is obtained when the fourth oxygen or
poly-phosphate environment is added to the phosphorus compound. These BE values are useful to researchers involved
in identifying oxidation states of phosphorus and sulfur atoms commonly observed on modified surfaces and interfaces
found in applications such as biomaterials, super-capacitors and catalysis.
The biomass concentration of microalgae growth in photobioreactor was predicted using the Monod-based growth models. Kinetic parameters such as maximum specific growth rate and saturation constant of light intensity were evaluated by nonlinear least squares methods that focused on minimizing the sum of squares error (SSE). The importance of good initial guess for the nonlinear least squares method was also discussed. The optimal control problem of the microalgae growth model was determined based on parameter sensitivity. Therefore, a dynamic optimization approach was used where an optimal input design method was formulated to obtain a control function of a problem. The dynamic state equations, additional state equations, cost function, and Hamiltonian function were used to establish a control function of microalgae growth in a photobioreactor. Hence, the biomass production of microalgae can be predicted using numerical methods such as the Taylor series method.
Suis nanoelektromekanikal (NEM) mempunyai persamaan dengan suis konvensional semikonduktor apabila digunakan
sebagai transistor dan penderia walaupun prinsip operasinya berbeza. Perbezaan prinsip operasi suis ini memberikan
kelebihan kepada suis NEM untuk beroperasi dalam persekitaran yang melampau manakala suis konvensional
semikonduktor mempunyai kelebihan daripada segi infrastruktur fabrikasi yang canggih. Dalam kertas ini, kami
mengulas kemajuan terbaru dan potensi teknologi NEM dalam aplikasi pensuisan berdasarkan bahan berasaskan karbon
seperti CNT dan grafin. Kemajuan reka bentuk geometri suis NEM seperti struktur rusuk berlubang, mempunyai kelebihan
daripada segi voltan operasi peranti yang rendah, turut dibincangkan dalam kertas ini. Berdasarkan Kitaran Gemburan
Gartner, teknologi, proses dan produk untuk suis NEM atau hibrid NEM-CMOS berada di takuk berbeza iaitu di jurang
ilusi, cerun pencerahan dan dataran tinggi produktiviti. Kemudian, reka bentuk geometri suis NEM berasaskan bahanbahan
ini diulas dengan lengkap berdasarkan kajian kepustakaan terbaru. Kami mengenal pasti cabaran yang terlibat
dalam proses fabrikasi suis NEM berasaskan CNT dan grafin seperti kebocoran get dan proses litografi yang mencabar.
Kesimpulannya, kami meringkaskan kertas kajian ini kepada beberapa sudut perspektif, pandangan dan peluang pada
masa depan dalam teknologi suis NEM.
As some proteins are known to interact with sulfated and phosphated biomolecules such as specific glycosaminoglycans, this study derives from the hypothesis that sulfonate and phosphonate groups on solid polymer surfaces might cause specific interfacial interactions. Such surfaces were prepared by plasma polymerization of heptylamine (HA) and subsequent grafting of sulfonate or phosphonate groups via Michael-type addition of vinylic compounds. Adsorption of the proteins fibrinogen, albumin (HSA) and lysozyme on these functionalised plasma polymer surfaces was studied by XPS and quartz crystal microbalance with dissipation (QCM-D). It was also studied whether pre-adsorption with HSA would lead to a passivated surface against further adsorption of other proteins. XPS confirmed grafting of vinyl sulfonate and vinyl phosphonate onto the amine surface and showed that the proteins adsorbed to saturation at between 1 and 2 h. QCM-D showed rapid and irreversible adsorption of albumin on all three surfaces, while lysozyme could be desorbed with PBS to substantial extents from the sulfonated and phosphonated surfaces but not from the amine surface. Fibrinogen showed rapid initial adsorption followed by slower additional mass gain over hours. Passivation with albumin led to small and largely reversible subsequent adsorption of lysozyme, whereas with fibrinogen partial displacement yielded a mixed layer, regardless of the surface chemistry. Thus, protein adsorption onto these sulfonated and phosphonated surfaces is complex, and not dominated by electrostatic charge effects.
Role of sulfur (S) and nitrogen (N) groups in promoting cell adhesion or commonly known as biocompatibility, is well established, but their role in reducing bacterial attachment and growth is less explored or not well-understood. Natural sulfur-based compounds, i.e. sulfide, sulfoxide and sulfinic groups, have shown to inhibit bacterial adhesion and biofilm formation. Hence, we mimicked these surfaces by plasma polymerizing thiophene (ppT) and air-plasma treating this ppT to achieve coatings with S of similar oxidation states as natural compounds (ppT-air). In addition, the effects of these N and S groups from ppT-air were also compared with the biocompatible amine-amide from n-heptylamine plasma polymer. Crystal violet assay and live and dead fluorescence staining of E. coli and S. aureus showed that all the N and S coated surfaces generated, including ppHA, ppT and ppT-air, produced similarly potent, growth reduction of both bacteria by approximately 65% at 72 h compared to untreated glass control. The ability of osteogenic differentiation in Wharton's jelly mesenchymal stem cells (WJ-MSCs) were also used to test the cell biocompatibility of these surfaces. Alkaline phosphatase assay and scanning electron microscopy imaging of these WJ-MSCs growths indicated that ppHA, and ppT-air were cell-friendly surfaces, with ppHA showing the highest osteogenic activity. In summary, the N and S containing surfaces could reduce bacteria growth while promoting mammalian cell growth, thus serve as potential candidate surfaces to be explored further for biomaterial applications.
Cold plasma (low pressure) technology has been effectively used to boost the germination and growth of various crops in recent decades. The durability of these plasma-treated seeds is essential because of the need to store and distribute the seeds at different locations. However, these ageing effects are often not ascertained and reported because germination and related tests are carried out within a short time after the plasma-treatment. This research aims to fill that knowledge gap by subjecting three different types of seeds (and precursors): Bambara groundnuts (water), chilli (oxygen), and papaya (oxygen) to cold plasma-treatment. Common mechanisms found for these diverse seed types and treatment conditions were the physical and chemical changes induced by the physical etching and the cold plasma on the seeds and subsequent oxidation, which promoted germination and growth. The high glass transition temperature of the lignin-cellulose prevented any physical restructuring of the surfaces while maintaining the chemical changes to continue to promote the seeds germination and growth. These changes were monitored over 60 days of ageing using water contact angle (WCA), water uptake, electrical conductivity, field emission scanning electron microscopy (FE-SEM) and X-ray photoelectron spectroscopy (XPS). The vacuum effect was also investigated to separate its effect from cold plasma (low pressure). This finding offers a framework for determining how long agricultural seeds that have received plasma treatment can be used. Additionally, there is a need to transfer this research from the lab to the field. Once the impact of plasma treatment on seeds has been estimated, it will be simple to do so.
Our preliminary results indicated that fibrin and poly(lactic-co-glycolic acid) (PLGA) hybrid scaffold promoted early chondrogenesis of articular cartilage constructs in vitro. The aim of this study was to evaluate in vivo cartilaginous tissue formation by chondrocyte-seeded fibrin/PLGA hybrid scaffolds. PLGA scaffolds were soaked carefully, in chondrocyte-fibrin suspension, and polymerized by dropping thrombin-calcium chloride (CaCl2) solution. PLGA-seeded chondrocytes were used as a control. Resulting constructs were implanted subcutaneously, at the dorsum of nude mice, for 4 weeks. Macroscopic observation, histological evaluation, gene expression and sulphated-glycosaminoglycan (sGAG) analyses were performed at each time point of 1, 2 and 4 weeks post-implantation. Cartilaginous tissue formation in fibrin/PLGA hybrid construct was confirmed by the presence of lacunae and cartilage-isolated cells embedded within basophilic ground substance. Presence of proteoglycan and glycosaminoglycan (GAG) in fibrin/PLGA hybrid constructs was confirmed by positive Safranin O and Alcian Blue staining. Collagen type II exhibited intense immunopositivity at the pericellular matrices. Chondrogenic properties were further demonstrated by the expression of gene encoded cartilage-specific markers, collagen type II and aggrecan core protein. The sGAG production in fibrin/PLGA hybrid constructs was higher than in the PLGA group. In conclusion, fibrin/PLGA hybrid scaffold promotes cartilaginous tissue formation in vivo and may serve as a potential cell delivery vehicle and a structural basis for articular cartilage tissue-engineering.
A total of 422 Mycobacterium tuberculosis isolates from eight countries were subjected to IS6110 and IS1081 DNA fingerprinting by means of restriction fragment analysis to characterize M. tuberculosis strains from each country. Chinese, Mongolian, Hong Kong, Filipino, and Korean isolates had comparatively more copies of IS6110 (proportion with eight or more copies; 95% +/- 5%), while Thai, Malaysian, and Vietnamese isolates had fewer copies (proportion with eight or more copies, 60% +/- 4%). We found a number of novel IS1081 types in this study. One IS1081 type was present in 56% of Filipino isolates, had a specific 6.6-kb PvuII fragment in its IS6110 DNA fingerprint, and was termed the "Filipino family." The IS1081 types of Thai isolates had interposing characteristics between the characteristics of northeastern Asian and southeastern Asian IS1081 types. A 1.3-kb single-copy IS6110 fragment was found only in Vietnamese M. tuberculosis isolates. Although M. tuberculosis isolates from each country had comparatively similar characteristics depending on the classification factor, each country's isolates showed characteristic DNA fingerprints and differed slightly from the isolates from the other countries in either the mode number of IS6110 copies or the distribution of IS1081 types.
Menstruation is associated with significant unpleasantness, and wearing a sanitary napkin (SN) during menses causes discomfort. In addition, many Muslim women use a thick type of SN during menses due to the religious requirement that even disposable SNs be washed before disposal. Therefore, the objective of this study was to measure the physiological and psychological responses to wearing SNs of different thicknesses during menstruation and non-menstruation phases at rest and during physical activity/exercise among Muslim women.
Antibacterial coating is necessary to prevent biofilm-forming bacteria from colonising medical tools causing infection and sepsis in patients. The recent coating strategies such as immobilisation of antimicrobial materials and low-pressure plasma polymerisation may require multiple processing steps involving a high-vacuum system and time-consuming process. Some of those have limited efficacy and durability. Here, we report a rapid and one-step atmospheric pressure plasma polymerisation (APPP) of D-limonene to produce nano-thin films with hydrophobic-like properties for antibacterial applications. The influence of plasma polymerisation time on the thickness, surface characteristic, and chemical composition of the plasma-polymerised films was systematically investigated. Results showed that the nano-thin films deposited at 1 min on glass substrate are optically transparent and homogenous, with a thickness of 44.3 ± 4.8 nm, a smooth surface with an average roughness of 0.23 ± 0.02 nm. For its antimicrobial activity, the biofilm assay evaluation revealed a significant 94% decrease in the number of Escherichia coli (E. coli) compared to the control sample. More importantly, the resultant nano-thin films exhibited a potent bactericidal effect that can distort and rupture the membrane of the treated bacteria. These findings provide important insights into the development of bacteria-resistant and biocompatible coatings on the arbitrary substrate in a straightforward and cost-effective route at atmospheric pressure.
Tissue engineering products have grown in popularity as a therapeutic approach for chronic wounds and burns. However, some drawbacks include additional steps and a lack of antibacterial capacities, both of which need to be addressed to treat wounds effectively. This study aimed to develop an acellular, ready-to-use ovine tendon collagen type I (OTC-I) bioscaffold with an antibacterial coating for the immediate treatment of skin wounds and to prevent infection post-implantation. Two types of crosslinkers, 0.1% genipin (GNP) and dehydrothermal treatment (DHT), were explored to optimise the material strength and biodegradability compared with a non-crosslinked (OTC) control. Carvone plasma polymerisation (ppCar) was conducted to deposit an antibacterial protective coating. Various parameters were performed to investigate the physicochemical properties, mechanical properties, microstructures, biodegradability, thermal stability, surface wettability, antibacterial activity and biocompatibility of the scaffolds on human skin cells between the different crosslinkers, with and without plasma polymerisation. GNP is a better crosslinker than DHT because it demonstrated better physicochemical properties (27.33 ± 5.69% vs. 43 ± 7.64% shrinkage), mechanical properties (0.15 ± 0.15 MPa vs. 0.07 ± 0.08 MPa), swelling (2453 ± 419.2% vs. 1535 ± 392.9%), biodegradation (0.06 ± 0.06 mg/h vs. 0.15 ± 0.16 mg/h), microstructure and biocompatibility. Similarly, its ppCar counterpart, GNPppCar, presents promising results as a biomaterial with enhanced antibacterial properties. Plasma-polymerised carvone on a crosslinked collagen scaffold could also support human skin cell proliferation and viability while preventing infection. Thus, GNPppCar has potential for the rapid treatment of healing wounds.
The miniaturization trend leads to the development of a graphene based nanoelectromechanical (NEM) switch to fulfill the high demand in low power device applications. In this article, we highlight the finite element (FEM) simulation of the graphene-based NEM switches of fixed-fixed ends design with beam structures which are perforated and intact. Pull-in and pull-out characteristics are analyzed by using the FEM approach provided by IntelliSuite software, version 8.8.5.1. The FEM results are consistent with the published experimental data. This analysis shows the possibility of achieving a low pull-in voltage that is below 2 V for a ratio below 15:0.03:0.7 value for the graphene beam length, thickness, and air gap thickness, respectively. The introduction of perforation in the graphene beam-based NEM switch further achieved the pull-in voltage as low as 1.5 V for a 250 nm hole length, 100 nm distance between each hole, and 12-number of hole column. Then, a von Mises stress analysis is conducted to investigate the mechanical stability of the intact and perforated graphene-based NEM switch. This analysis shows that a longer and thinner graphene beam reduced the von Mises stress. The introduction of perforation concept further reduced the von Mises stress at the graphene beam end and the beam center by approximately ~20⁻35% and ~10⁻20%, respectively. These theoretical results, performed by FEM simulation, are expected to expedite improvements in the working parameter and dimension for low voltage and better mechanical stability operation of graphene-based NEM switch device fabrication.
Acacia species are multipurpose trees, widely used in the traditional systems of medicine to treat various ailments. The major objective of the present study was to determine the gene expression of enzymatic antioxidants by acetone extract from the stem bark of three Acacia species (Acacia dealbata, Acacia ferruginea and Acacia leucophloea) in hydrogen peroxide (H2O2)-induced human hepatoma (HepG2) cells. The expression of antioxidant enzymes such as superoxide dismutase containing copper-zinc (CuZnSOD)/manganese (MnSOD), catalase (CAT) and glutathione peroxidase (GPx) in HepG2 cells was evaluated by real-time PCR. The results of antioxidant enzyme expression in real-time PCR study revealed that the H2O2 (200 μM) challenged HepG2 cells reduced the expression of enzymes such as SOD, GPx and CAT. However, the cells pre-treated with acetone extracts of all the three Acacia species significantly (P > 0.05) up-regulated the expression of antioxidant enzymes in a concentration dependent manner (25, 50 and 75 μg/mL). In conclusion, the findings of our study demonstrated that the acetone extract of Acacia species effectively inhibited H2O2 mediated oxidative stress and may be useful as a therapeutic agent in preventing oxidative stress mediated diseases.
We present a case of an undifferentiated subtype of non-keratinizing squamous cell carcinoma (NK-SCC) with sarcomatoid features in the nasopharynx in a 69-year-old man who was difficult to diagnose due to spindle-shaped malignant cells. He was admitted because of a right nasal obstruction and right headache, and imaging revealed a heterogeneously enhanced irregularly shaped mass at the nasopharynx. Histopathologically, the tumour was partially organised, and the tumour cells were epithelioid or spindle-shaped. Initially, we erroneously diagnosed the tumour as an angiosarcoma owing to its false-negative immunoreaction for cytokeratins and a mistaken interpretation for CD31. After in situ hybridization for Epstein-Barr virus was positive, a consultation and additional immunostaining (including re-staining for cytokeratin with varying dilutions) were performed, and the diagnosis was revised to NK-SCC with sarcomatoid features. We believe that sarcomatoid features may be observed in nasopharyngeal carcinoma and in this case, immunostaining using various epithelial markers is necessary and careful attention should be paid to the interpretation of immunostaining.
One-day-old chickens were transported from Australia to Malaysia and vaccinated orotracheally with an uninactivated vaccine prepared from avirulent Australian V4 strain of Newcastle disease virus (NDV). The vaccination regimes were as follows: group A, once, at 2 weeks old; group B, once, at 3 weeks old; group C, twice, at 2 and at 3 weeks old; group D, direct contact with groups A, B, and C; and group E, indirect contact with groups A, B, C, and D. Group F was unvaccinated controls. Challenge was with NDV virulent Ipoh AF 2240-226 strain, administered at 4 weeks old intramuscularly to 10 chickens in each group and orotracheally to 10 chickens in each group. The remaining chickens were challenged by contact with the inoculated chickens. Group mortalities following challenge were: A, 1/77; B, 1/34; C, 0/39; D, 0/45; E, 6/43; and F, 60/60.
A minimally-sized, triple-notched band ultra-wideband (UWB) antenna, useful for many applications, is designed, analyzed, and experimentally validated in this paper. A modified maple leaf-shaped main radiating element with partial ground is used in the proposed design. An E-shaped resonator, meandered slot, and U-shaped slot are implemented in the proposed design to block the co-existing bands. The E-shaped resonator stops frequencies ranging from 1.8⁻2.3 GHz (Advanced Wireless System (AWS1⁻AWS2) band), while the meandered slot blocks frequencies from 3.2⁻3.8 GHz (WiMAX band). The co-existing band ranging from 5.6⁻6.1 GHz (IEEE 802.11/HIPERLANband) is blocked by utilizing the U-shaped section in the feeding network. The notched bands can be independently controlled over a wide range of frequencies using specific parameters. The proposed antenna is suitable for many applications because of its flat gain, good radiation characteristics at both principal planes, uniform group delay, and non-varying transfer function ( S 21 ) for the entire UWB frequency range.
Alzheimer's disease (AD), the most common form of senile dementia, is a genetically complex disorder. In most Asian countries, the population and the number of AD patients are growing rapidly, and the genetics of AD has been extensively studied, except in Japan. However, recent studies have been started to investigate the genes and mutations associated with AD in Korea, the People's Republic of China, and Malaysia. This review describes all of the known mutations in three early-onset AD (EOAD) causative genes (APP, PSEN1, and PSEN2) that were discovered in Asian countries. Most of the EOAD-associated mutations have been detected in PSEN1, and several novel PSEN1 mutations were recently identified in patients from various parts of the world, including Asia. Until 2014, no PSEN2 mutations were found in Asian patients; however, emerging studies from Korea and the People's Republic of China discovered probably pathogenic PSEN2 mutations. Since several novel mutations were discovered in these three genes, we also discuss the predictions on their pathogenic nature. This review briefly summarizes genome-wide association studies of late-onset AD and the genes that might be associated with AD in Asian countries. Standard sequencing is a widely used method, but it has limitations in terms of time, cost, and efficacy. Next-generation sequencing strategies could facilitate genetic analysis and association studies. Genetic testing is important for the accurate diagnosis and for understanding disease-associated pathways and might also improve disease therapy and prevention.
An increasing concern on resistance to multiple-antibiotics has led to the discovery of novel agents and the establishment of new precaution strategy. Numerous plant sources have been widely studied to reduce virulence of pathogenic bacteria by interfering cell-to-cell based communication called quorum sensing (QS). Leaf extracts of 17 gardening trees were collected and investigated for their anti-QS effects using a sensor strain Chromobacterium violaceum CV026. Methanolic extracts of K4 (Acer palmatum), K9 (Acer pseudosieboldianum) and K13 (Cercis chinensis) leaves were selected for further experiments based on their antagonism effect on QS without inhibiting C. violaceum CV026 growth. Subsequently, the leaf extracts on QS-mediated virulence of Pseudomonas aeruginosa PAO1 involved in biofilm formation, motility, bioluminescence, pyocyanin production, QS molecules production, and Caenorhabditis elegans killing activity were evaluated. The biofilm formation ability and swarming motility of P. aeruginosa PAO1 were decreased approximately 50% in the presence of these leaf extracts at a concentration of 1 mg/mL. The expression level of lecA::lux of P. aeruginosa PAO1 and pyocyanin production were also reduced. The three leaf extracts also decreased autoinducer (AI) production in P. aeruginosa PAO1 without direct degradation, suggesting that AI synthesis might have been suppressed by these extracts. The three leaf extracts also showed anti-infection activity in C. elegans model. Taken together, these results suggest that methanolic leaf extracts of K4, K9 and K13 have the potential to attenuate the virulence of P. aeruginosa PAO1.