Displaying publications 1 - 20 of 54 in total

Abstract:
Sort:
  1. Sulaiman AZ, Ajit A, Chisti Y
    Biotechnol Prog, 2013 Nov-Dec;29(6):1448-57.
    PMID: 23926080 DOI: 10.1002/btpr.1786
    A recombinant Trichoderma reesei cellulase was used for the ultrasound-mediated hydrolysis of soluble carboxymethyl cellulose (CMC) and insoluble cellulose of various particle sizes. The hydrolysis was carried out at low intensity sonication (2.4-11.8 W cm(-2) sonication power at the tip of the sonotrode) using 10, 20, and 40% duty cycles. [A duty cycle of 10%, for example, was obtained by sonicating for 1 s followed by a rest period (no sonication) of 9 s.] The reaction pH and temperature were always 4.8 and 50°C, respectively. In all cases, sonication enhanced the rate of hydrolysis relative to nonsonicated controls. The hydrolysis of CMC was characterized by Michaelis-Menten kinetics. The Michaelis-Menten parameter of the maximum reaction rate Vmax was enhanced by sonication relative to controls, but the value of the saturation constant Km was reduced. The optimal sonication conditions were found to be a 10% duty cycle and a power intensity of 11.8 W cm(-2) . Under these conditions, the maximum rate of hydrolysis of soluble CMC was nearly double relative to control. In the hydrolysis of cellulose, an increasing particle size reduced the rate of hydrolysis. At any fixed particle size, sonication at a 10% duty cycle and 11.8 W cm(-2) power intensity improved the rate of hydrolysis relative to control. Under the above mentioned optimal sonication conditions, the enzyme lost about 20% of its initial activity in 20 min. Sonication was useful in accelerating the enzyme catalyzed saccharification of cellulose.
    Matched MeSH terms: Carboxymethylcellulose Sodium/chemistry*
  2. Ma J, Ma NL, Zhang D, Wu N, Liu X, Meng L, et al.
    Chemosphere, 2022 Apr;292:133345.
    PMID: 34922964 DOI: 10.1016/j.chemosphere.2021.133345
    Zero waste multistage utilization of biomass from Ginkgo biloba branches (GBBs) was achieved through extraction of bioactive components, analysis of antioxidant and antibacterial activities, preparation and composition of pyrolyzate, adsorption and reuse of modified biochar. The results showed that GBBs had abundant bioactive components for potential application in the industry of food, chemical raw materials and biomedicine. Especially, the bioactive compounds in acetone extract (10 mg/mL) of GBBs identified by DPPH and ABTS had free radical scavenging abilities of 92.28% and 98.18%, respectively, which are equivalent to Vitamin C used as an antioxidant in food additives. Fourier Transform Infrared and X-Ray Diffraction analysis showed that carboxymethyl cellulose (CMC) and magnetic Fe3O4 were successfully incorporated into raw biochar (RB) to form CMC-Fe3O4-RB nanomaterial. Scanning electron microscopy and X-Ray Diffraction spectroscopy displayed Fe, C, and O existed on the surface of CMC-Fe3O4-RB. Compared with RB, CMC-Fe3O4-RB had a larger specific surface area, pore volume and pore size. Meanwhile, nanomagnetic CMC-Fe3O4-RB solved the problem of agglomeration in traditional magnetized biochar production, and improved the adsorption capacity of Pb2+, which was 29.90% higher than that of RB by ICP-OES. Further, the Pb2+ (10 mg/L) adsorption capacity of CMC-Fe3O4-RB reached the highest level in 2 h at the dosage of 0.01 g/L, and remained stable at 52.987 mg/g after five cycles of adsorption and desorption. This research aided in the creation of a strategy for GBBs zero waste multistage usage and a circular economic model for GBBs industry development, which can be promoted and applied to the fields of food industry and environment improvement.
    Matched MeSH terms: Carboxymethylcellulose Sodium
  3. Khan MSJ, Sidek LM, Kamal T, Asiri AM, Khan SB, Basri H, et al.
    Int J Biol Macromol, 2024 Feb;257(Pt 1):128544.
    PMID: 38061525 DOI: 10.1016/j.ijbiomac.2023.128544
    This work reports silver nanoparticles (AgNPs) supported on biopolymer carboxymethyl cellulose beads (Ag-CMC) serves as an efficient catalyst in the reduction process of p-nitrophenol (p-NP) and methyl orange (MO). For Ag-CMC synthesis, first CMC beads were prepared by crosslinking the CMC solution in aluminium nitrate solution and then the CMC beads were introduced into AgNO3 solution to adsorb Ag ions. Field emission scanning electron microscopy (FE-SEM) analysis suggests the uniform distribution of Ag nanoparticles on the CMC beads. The X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) analysis revealed the metallic and fcc planes of AgNPs, respectively, in the Ag-CMC catalyst. The Ag-CMC catalyst exhibits remarkable reduction activity for the p-NP and MO dyes with the highest rate constant (kapp) of a chemical reaction is 0.519 and 0.697 min-1, respectively. Comparative reduction studies of Ag-CMC with CMC, Fe-CMC and Co-CMC disclosed that Ag-CMC containing AgNPs is an important factore in reducing the organic pollutants like p-NP and MO dyes. During the recyclability tests, the Ag-CMC also maintained high reduction activity, which suggests that CMC protects the AgNPs from leaching during dye reduction reactions.
    Matched MeSH terms: Carboxymethylcellulose Sodium
  4. Ahmad NH, Isa MIN
    Carbohydr Polym, 2016 Feb 10;137:426-432.
    PMID: 26686147 DOI: 10.1016/j.carbpol.2015.10.092
    Two solid biopolymer electrolytes (SBEs) systems of carboxymethyl cellulose doped ammonium chloride (CMC-AC) and propylene carbonate plasticized (CMC-AC-PC) were prepared via solution casting technique. The ionic conductivity of SBEs were analyzed using electrical impedance spectroscopy (EIS) in the frequency range of 50 Hz-1 MHz at ambient temperature (303K). The highest ionic conductivity of CMC-AC SBE is 1.43 × 10(-3)S/cm for 16 wt.% of AC while the highest conductivity of plasticized SBE system is 1.01 × 10(-2)S/cm when added with 8 wt.% of PC. TGA/DSC showed that the addition of PC had increased the decomposition temperature compared of CMC-AC SBE. Fourier transform infrared (FTIR) spectra showed the occurrence of complexation between the SBE components and it is proved successfully executed by Gaussian software. X-ray diffraction (XRD) indicated that amorphous nature of SBEs. It is believed that the PC is one of the most promising plasticizer to enhance the ionic conductivity and performance for SBE system.
    Matched MeSH terms: Carboxymethylcellulose Sodium/chemistry*
  5. Ramlli MA, Isa MI
    J Phys Chem B, 2016 11 10;120(44):11567-11573.
    PMID: 27723333
    Fourier transform infrared (FT-IR), X-ray diffraction (XRD), and transference number measurement (TNM) techniques were applied to investigate the complexation, structural, and ionic transport properties of and the dominant charge-carrier species in a solid biopolymer electrolyte (SBE) system based on carboxymethyl cellulose (CMC) doped with ammonium fluoride (NH4F), which was prepared via a solution casting technique. The SBEs were partially opaque in appearance, with no phase separation. The presence of interactions between the host polymer (CMC) and the ionic dopant (NH4F) was proven by FT-IR analysis at the C-O band. XRD spectra analyzed using Origin 8 software disclose that the degree of crystallinity (χc%) of the SBEs decreased with the addition of NH4F, indicating an increase in the amorphous nature of the SBEs. Analysis of the ionic transport properties reveals that the ionic conductivity of the SBEs is dependent on the ionic mobility (μ) and diffusion of ions (D). TNM analysis confirms that the SBEs are proton conductors.
    Matched MeSH terms: Carboxymethylcellulose Sodium/chemistry*
  6. Chan YW, Acquah C, Obeng EM, Dullah EC, Jeevanandam J, Ongkudon CM
    Biochimie, 2019 Feb;157:204-212.
    PMID: 30513369 DOI: 10.1016/j.biochi.2018.11.019
    Biocarriers are pivotal in enhancing the reusability of biocatalyst that would otherwise be less economical for industrial application. Ever since the induction of enzymatic technology, varied materials have been assessed for their biocompatibility with enzymes of distinct functionalities. Herein, cellulase was immobilized onto polymethacrylate particles (ICP) as the biocarrier grafted with ethylenediamine (EDA) and glutaraldehyde (GA). Carboxymethyl cellulose (CMC) was used as a model substrate for activity assay. Enzyme immobilization loading was determined by quantifying the dry weight differential of ICP (pre-& post-immobilization). Cellulase was successfully demonstrated to be anchored upon ICP and validated by FTIR spectra analysis. The optimal condition for cellulase immobilization was determined to be pH 6 at 20 °C. The maximum CMCase activity was achieved at pH 5 and 50 °C. Residual activity of ∼50% was retained after three iterations and dipped to ∼18% on following cycle. Also, ICP displayed superior pH adaptability as compared to free cellulase. The specific activity of ICP was 65.14 ± 1.11% relative to similar amount of free cellulase.
    Matched MeSH terms: Carboxymethylcellulose Sodium/chemistry*
  7. Fu J, Yap JX, Leo CP, Chang CK
    Int J Biol Macromol, 2023 Apr 15;234:123642.
    PMID: 36791941 DOI: 10.1016/j.ijbiomac.2023.123642
    Although anionic polyelectrolyte hydrogel beads offer attractive adsorption of cationic dyes, phosphate adsorption is limited by electrostatic interactions. In this work, carboxymethyl cellulose (CMC)/sodium alginate (SA) hydrogel beads were modified with calcium carbonate (CaCO3) and/or bentonite (Be). The compatibility between CaCO3 and Be was proven by the homogeneous surface, as shown in the scanning electron microscopic images. Fourier-transform infrared and X-ray diffraction spectra further confirmed the existence of inorganic filler in the hydrogel beads. Although CMC/SA/Be/CaCO3 hydrogel beads attained the highest methylene blue and phosphate adsorption capacities (142.15 MB mg/g, 90.31 P mg/g), phosphate adsorption was significantly improved once CaCO3 nanoparticles were incorporated into CMC/SA/CaCO3 hydrogel beads. The kinetics of MB adsorption by CMC/SA hydrogel beads with or without inorganic fillers could be described by the pseudo-second-order model under chemical interactions. The phosphate adsorption by CMC/SA/Be/CaCO3 hydrogel beads could be explained by the Elovich model due to heterogeneous properties. The incorporation of Be and CaCO3 also improved the phosphate adsorption through chemical interaction since Langmuir isotherm fitted the phosphate adsorption by CMC/SA/Be/CaCO3 hydrogel beads. Unlike MB adsorption, the reusability of these hydrogel beads in phosphate adsorption reduced slightly after 5 cycles.
    Matched MeSH terms: Carboxymethylcellulose Sodium/chemistry
  8. Vijayasree VP, Abdul Manan NS
    Int J Biol Macromol, 2023 Jul 01;242(Pt 1):124723.
    PMID: 37148927 DOI: 10.1016/j.ijbiomac.2023.124723
    In this study, magnetite carboxymethylcellulose (CMC@Fe3O4) composite as magnetic biological molecules were synthetized for the use as adsorbent to remove four types of cationic dyes, namely Methylene Blue, Rhodamine B, Malachite Green, and Methyl Violet from aqueous solution. The characteristic of the adsorbent was achieved by Fourier Transform Infrared Spectroscopy, Field Emission Scanning Electron Microscope (FESEM), X-ray Diffraction, Vibrating Sample Magnetometer and Thermal Gravimetric Analysis techniques. Besides, essential influencing parameters of dye adsorption; the solution pH, solution temperature, contact time, adsorbent concentration and initial dye dosage were studied. FESEM analysis showed the magnetic Fe3O4-TB, Fe3O4@SiO2, Fe3O4@SiO2-NH2 and CMC@Fe3O4 composites were in spherical shape, with average size of 43.0 nm, 92.5 nm, 134.0 nm and 207.5 nm, respectively. On the saturation magnetization (Ms), the results obtained were 55.931 emu/g, 34.557 emu/g, 33.236 emu/g and 11.884 emu/g. From the sorption modelling of Isotherms, Kinetics, and Thermodynamics, the adsorption capacity of dyes is (MB = 103.33 mg/g), (RB = 109.60 mg/g), (MG = 100.08 mg/g) and (MV = 107.78 mg/g). With all the adsorption processes exhibited as exothermic reactions. The regeneration and reusability of the synthetized biological molecules-based adsorbent was also assessed.
    Matched MeSH terms: Carboxymethylcellulose Sodium/chemistry
  9. Chai MN, Isa MI
    Sci Rep, 2016 Jun 06;6:27328.
    PMID: 27265642 DOI: 10.1038/srep27328
    The plasticized solid bio-polymer electrolytes (SBEs) system has been formed by introducing glycerol (Gly) as the plasticizer into the carboxymethyl cellulose (CMC) doped with oleic acid (OA) via solution casting techniques. The ionic conductivity of the plasticized SBEs has been studied using Electrical Impedance Spectroscopy. The highest conductivity achieved is 1.64 × 10(-4) S cm(-1) for system containing 40 wt. % of glycerol. FTIR deconvolution technique had shown that the conductivity of CMC-OA-Gly SBEs is primarily influenced by the number density of mobile ions. Transference number measurement has shown that the cation diffusion coefficient and ionic mobility is higher than anion which proved the plasticized polymer system is a proton conductor.
    Matched MeSH terms: Carboxymethylcellulose Sodium/metabolism*
  10. NG PEI QI, NOR HAYATI IBRAHIM, AZLIN SHAFRINA HASIM
    MyJurnal
    Biopolymer interaction in oil-in-water (o/w) emulsions has been demonstrated to positively modify the emulsion physicochemical properties which lead to desirable stability. The present work focused on the effect of pea protein isolate (PPI), pectin, carboxymethyl cellulose (CMC) and their interaction on physicochemical properties and oxidative stability of o/w emulsions using a mixture design approach. The emulsions were prepared with 40 % sunflower oil stabilized with 1 % of PPI, pectin and CMC, respectively, as well as their mixtures according to a simplex-centroid design (10 points). ThepH values for all emulsions were within acidic condition (3.22 to 4.66) and increased significantly (p
    Matched MeSH terms: Carboxymethylcellulose Sodium
  11. Lua GW, Tang J, Liu F, Li ZS
    Dig Dis Sci, 2016 06;61(6):1763-9.
    PMID: 26809870 DOI: 10.1007/s10620-016-4034-4
    BACKGROUND: Esophageal stricture is one of the serious adverse events following endoscopic submucosal dissection (ESD). However, optimum preventive techniques are still lacking.

    AIMS: Our primary objective was to evaluate the incidence of post-ESD esophageal stricture with the application of carboxymethyl cellulose (CMC) sheets. Secondary objectives were to determine the number of sessions of endoscopic balloon dilatation (EBD) required to resolve post-ESD strictures and the incidence rate of peri-operative adverse events.

    METHODS: This was a pilot, single-center, prospective study. Seven patients who had high risks of developing post-ESD esophageal stricture were enrolled into our study. CMC sheets were applied to the mucosal defects immediately after the completion of ESD. Patients were monitored and reviewed after ESD to detect any adverse events.

    RESULTS: The incidence rate of post-operative stricture was 57 % (4/7 patients). Among patients who required EBD, the number of sessions performed was 2.8 ± 2.2. No serious post-operative adverse events were reported.

    CONCLUSION: The use of CMC sheets appears to be a safe and effective prophylactic treatment for esophageal stricture following extensive ESD.

    Matched MeSH terms: Carboxymethylcellulose Sodium/administration & dosage; Carboxymethylcellulose Sodium/therapeutic use*
  12. Wong TW, Ramli NA
    Carbohydr Polym, 2014 Nov 4;112:367-75.
    PMID: 25129756 DOI: 10.1016/j.carbpol.2014.06.002
    Infection control and wound healing profiles of sodium carboxymethylcellulose (SCMC) films were investigated as a function of their anti-bacterial action, physical structures, polymer molecular weights and carboxymethyl substitution degrees. The films were prepared with in vitro polymer/film and in vivo microbe-colonized wound healing/systemic infection profiles examined. Adhesive high carboxymethyl substituted SCMC films aided healing via attaching to microbes and removing them from wound. Pseudomonas aeruginosa was removed via encapsulating in gelling low molecular weight SCMC film, whereas Staphylococcus aureus was trapped in tight folds of high molecular weight SCMC film. Incomplete microbe removal from wound did not necessary translate to inability to heal as microbe remnant at wound induced fibroblast migration and aided tissue reconstruction. Using no film nonetheless will cause systemic blood infection. SCMC films negate infection and promote wound healing via specific polymer-microbe adhesion, and removal of S. aureus and P. aeruginosa requires films of different polymer characteristics.
    Matched MeSH terms: Carboxymethylcellulose Sodium/pharmacology*; Carboxymethylcellulose Sodium/chemistry
  13. Peh KK, Wong CF
    J Pharm Pharm Sci, 1999 May-Aug;2(2):53-61.
    PMID: 10952770
    To investigate the suitability of an SCMC (sodium carboxymethyl cellulose/polyethylene glycol 400/carbopol 934P) and an HPMC (hydroxypropylmethyl cellulose/polyethylene glycol 400/carbopol 934P) films as drug vehicle for buccal delivery.
    Matched MeSH terms: Carboxymethylcellulose Sodium/administration & dosage*; Carboxymethylcellulose Sodium/chemistry
  14. Ramli NA, Wong TW
    Int J Pharm, 2011 Jan 17;403(1-2):73-82.
    PMID: 20974238 DOI: 10.1016/j.ijpharm.2010.10.023
    This study investigated critical physicochemical attributes of low (LV), medium (MV) and high molecular weight (HV) sodium carboxymethylcellulose (SCMC) scaffolds in partial thickness wound healing. SCMC scaffolds were prepared by solvent-evaporation technique. Their in vitro erosion, moisture affinity, morphology, tensile strength, polymer molecular weight and carboxymethyl substitution, and in vivo wound healing profiles were determined. Inferring from rat wound size, re-epithelialization and histological profiles, wound healing progressed with HV scaffold>LV-MV scaffold>control with no scaffold. The transepidermal water loss (TEWL) from wound of rats treated by control>HV scaffold>LV-MV scaffold. HV scaffold had the highest tensile strength of all matrices and was resistant to erosion in simulated wound fluid. In spite of constituting small nanopores, it afforded a substantial TEWL than MV and LV scaffolds from wound across an intact matrix through its low moisture affinity characteristics. The HV scaffold can protect moisture loss without its excessive accumulation at wound bed which hindered re-epithelialization process. Regulation of transepidermal water movement and wound healing by scaffolds was governed by SCMC molecular weight instead of its carboxymethyl substitution degree or matrix pore size distribution, with large molecular weight HV preferred over lower molecular weight samples.
    Matched MeSH terms: Carboxymethylcellulose Sodium/administration & dosage; Carboxymethylcellulose Sodium/chemistry*
  15. Gunny AA, Arbain D, Jamal P, Gumba RE
    Saudi J Biol Sci, 2015 Jul;22(4):476-83.
    PMID: 26150755 DOI: 10.1016/j.sjbs.2014.11.021
    Halophilic cellulases from the newly isolated fungus, Aspergillus terreus UniMAP AA-6 were found to be useful for in situ saccharification of ionic liquids treated lignocelluloses. Efforts have been taken to improve the enzyme production through statistical optimization approach namely Plackett-Burman design and the Face Centered Central Composite Design (FCCCD). Plackett-Burman experimental design was used to screen the medium components and process conditions. It was found that carboxymethylcellulose (CMC), FeSO4·7H2O, NaCl, MgSO4·7H2O, peptone, agitation speed and inoculum size significantly influence the production of halophilic cellulase. On the other hand, KH2PO4, KOH, yeast extract and temperature had a negative effect on enzyme production. Further optimization through FCCCD revealed that the optimization approach improved halophilic cellulase production from 0.029 U/ml to 0.0625 U/ml, which was approximately 2.2-times greater than before optimization.
    Matched MeSH terms: Carboxymethylcellulose Sodium
  16. Sohaimy MIHA, Isa MINM
    Polymers (Basel), 2020 Oct 26;12(11).
    PMID: 33114745 DOI: 10.3390/polym12112487
    Green and safer materials in energy storage technology are important right now due to increased consumption. In this study, a biopolymer electrolyte inspired from natural materials was developed by using carboxymethyl cellulose (CMC) as the core material and doped with varied ammonium carbonate (AC) composition. X-ray diffraction (XRD) shows the prepared CMC-AC electrolyte films exhibited low crystallinity content, Xc (~30%) for sample AC7. A specific wavenumber range between 900-1200 cm-1 and 1500-1800 cm-1 was emphasized in Fourier transform infrared (FTIR) testing, as this is the most probable interaction to occur. The highest ionic conductivity, σ of the electrolyte system achieved was 7.71 × 10-6 Scm-1 and appeared greatly dependent on ionic mobility, µ and diffusion coefficient, D. The number of mobile ions, η, increased up to the highest conducting sample (AC7) but it became less prominent at higher AC composition. The transference measurement, tion showed that the electrolyte system was predominantly ionic with sample AC7 having the highest value (tion = 0.98). Further assessment also proved that the H+ ion was the main conducting species in the CMC-AC electrolyte system, which presumably was due to protonation of ammonium salt onto the complexes site and contributed to the overall ionic conductivity enhancement.
    Matched MeSH terms: Carboxymethylcellulose Sodium
  17. Tangthuam P, Pimoei J, Mohamad AA, Mahlendorf F, Somwangthanaroj A, Kheawhom S
    Heliyon, 2020 Oct;6(10):e05391.
    PMID: 33150216 DOI: 10.1016/j.heliyon.2020.e05391
    The aim of this research is an evaluation of polyelectrolytes. In the application of zinc-iodine batteries (ZIBs), polyelectrolytes have high stability, good cationic exchange properties and high ionic conductivity. Polyelectrolytes are also cost-effective. Important component of ZIBs are cation exchange membranes (CEMs). CEMs prevent the crossover of iodine and polyiodide from zinc (Zn) electrodes. However, available CEMs are costly and have limited ionic conductivity at room temperature. CEMs are low-cost, have high stability and good cationic exchange properties. Herein, polyelectrolyte membranes prepared from carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVA) are examined. It is seen that an increase in the ratio of PVA leads to enhanced ionic conductivity as well as increased iodine and polyiodide crossover. ZIBs using polyelectrolytes having 75:25 wt.% CMC/PVA and 50:50 wt.% CMC/PVA show decent performance and cycling stability. Due to their low-cost and other salient features, CMC/PVA polyelectrolytes prove they have the capacity for use as cation exchange separators in ZIBs.
    Matched MeSH terms: Carboxymethylcellulose Sodium
  18. Ali MSM, Zainal Z, Hussein MZ, Wahid MH, Bahrudin NN, Muzakir MM, et al.
    Int J Biol Macromol, 2021 Jun 01;180:654-666.
    PMID: 33722623 DOI: 10.1016/j.ijbiomac.2021.03.054
    The present work developed porous carboxymethyl cellulose (CMC) carbon film from lignocellulosic based materials as supercapacitor electrode. Porous CMC carbon films of bamboo (B) and oil palm empty fruit bunch (O) were prepared through simple incipient wetness impregnation method followed by calcination process before incorporation with manganese oxide (Mn2O3). The carbonization produced porous CMC carbon whereby CMCB exhibited higher surface area than CMCO. After Mn2O3 incorporation, the crystallite size of CMCB and CMCO were calculated as 50.09 nm and 42.76 nm, respectively whereas Mn2O3/CMCB and Mn2O3/CMCO composite films were revealed to be 26.71 nm and 35.60 nm in size, respectively. Comparatively, the Mn2O3/CMCB composite film exhibited higher electrochemical performance which was 31.98 mF cm-2 as compared to 24.15 mF cm-2 by Mn2O3/CMCO composite film and both CMC carbon films with fairly stable cycling stability after 1000 charge-discharge cycles. Therefore, it can be highlighted that Mn2O3/CMC composite film as prepared from bamboo and oil palm fruit can potentially become the new electrode materials for supercapacitor application.
    Matched MeSH terms: Carboxymethylcellulose Sodium
  19. Basivi PK, Ramesh S, Kakani V, Yadav HM, Bathula C, Afsar N, et al.
    Sci Rep, 2021 May 10;11(1):9918.
    PMID: 33972653 DOI: 10.1038/s41598-021-89430-x
    In this study, a novel nanohybrid composite containing nitrogen-doped multiwalled carbon nanotubes/carboxymethylcellulose (N-MWCNT/CMC) was synthesized for supercapacitor applications. The synthesized composite materials were subjected to an ultrasonication-mediated solvothermal hydrothermal reaction. The synthesized nanohybrid composite electrode material was characterized using analytical methods to confirm its structure and morphology. The electrochemical properties of the composite electrode were investigated using cyclic voltammetry (CV), galvanic charge-discharge, and electrochemical impedance spectroscopy (EIS) using a 3 M KOH electrolyte. The fabricated composite material exhibited unique electrochemical properties by delivering a maximum specific capacitance of approximately 274 F g-1 at a current density of 2 A g-1. The composite electrode displayed high cycling stability of 96% after 4000 cycles at 2 A g-1, indicating that it is favorable for supercapacitor applications.
    Matched MeSH terms: Carboxymethylcellulose Sodium
  20. Shukri, W.H.Z., Hamzah, E.N.H., Halim, N.R.A., Isa, M.I.N., Sarbon, N.M.
    MyJurnal
    The aim of this work is to study the effect of hydrocolloids (guar gum, xanthan gum and carboxymethyl cellulose (CMC) on the physical properties and sensory evaluation of ice cream produced in order to investigate the potential of applying fermented glutinous rice (tapai pulut) as a value-added ingredient. The addition of 25% fermented glutinous rice was the most reliable amount to enhance the physical and sensory properties of ice cream when incorporating hydrocolloids. The addition of hydrocolloids significantly (p < 0.05) increased the pH, firmness, overrun, and melting rate of fermented glutinous rice ice cream. The addition of guar gum scored the highest firmness value (5403 g) followed by CMC (4630 g) and xanthan gum (3481g). Fermented glutinous rice ice cream with xanthan gum added, induced a noticeable change in overrun value (62%) while the addition of CMC decreased the melting rate compared to the control. The FTIR spectrum of fermented glutinous rice ice cream with different hydrocolloids containing carboxyl, amide and carbonyl group was appeared at 3362-3379 cm-1 , 1639-1640 cm-1 and 1026-1064 cm-1, respectively. In conclusion, the addition of xanthan gum presented great potential to improve the quality of fermented glutinous rice ice cream produced in terms of its firmness, overrun and melting rate.
    Matched MeSH terms: Carboxymethylcellulose Sodium
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links