Displaying publications 1 - 20 of 54 in total

Abstract:
Sort:
  1. Chai A, Wong YS, Ong SA, Aminah Lutpi N, Sam ST, Kee WC, et al.
    Bioresour Technol, 2021 Sep;336:125319.
    PMID: 34049168 DOI: 10.1016/j.biortech.2021.125319
    A pilot scale anaerobic degradation of sugarcane vinasse was carried out at various hydraulic retention time (HRT) in the Anaerobic Suspended Growth Closed Bioreactor (ASGCB) under thermophilic temperature. The performance and kinetics were evaluated through the Haldane-Andrews model to investigate the substrate inhibition potential of sugarcane vinasse. All parameters show great performance between HRT 35 and 25 days: chemical oxygen demand (COD) reduction efficiency (81.6 to 86.8%), volatile fatty acids (VFA) reduction efficiency (92.4 to 98.5%), maximum methane yield (70%) and maximum biogas production (19.35 L/day). Furthermore, steady state values from various HRT were obtained in the kinetic evaluation for: rXmax (1.20 /day), Ks (19.95 gCOD/L), Ki (7.00 gCOD/L) and [Formula: see text] (0.33 LCH4/gCOD reduction). This study shows that anaerobic degradation of sugarcane vinasse through ASGCB could perform well at high HRT and provides a low degree of substrate inhibition as compared to existing studies from literature.
    Matched MeSH terms: Saccharum*
  2. Chen WH, Hsu HJ, Kumar G, Budzianowski WM, Ong HC
    Bioresour Technol, 2017 Dec;246:12-19.
    PMID: 28803060 DOI: 10.1016/j.biortech.2017.07.184
    This study focuses on the biochar formation and torrefaction performance of sugarcane bagasse, and they are predicted using the bilinear interpolation (BLI), inverse distance weighting (IDW) interpolation, and regression analysis. It is found that the biomass torrefied at 275°C for 60min or at 300°C for 30min or longer is appropriate to produce biochar as alternative fuel to coal with low carbon footprint, but the energy yield from the torrefaction at 300°C is too low. From the biochar yield, enhancement factor of HHV, and energy yield, the results suggest that the three methods are all feasible for predicting the performance, especially for the enhancement factor. The power parameter of unity in the IDW method provides the best predictions and the error is below 5%. The second order in regression analysis gives a more reasonable approach than the first order, and is recommended for the predictions.
    Matched MeSH terms: Saccharum*
  3. Bheel N, Sohu S, Jhatial AA, Memon NA, Kumar A
    Environ Sci Pollut Res Int, 2022 Jan;29(4):5207-5223.
    PMID: 34420161 DOI: 10.1007/s11356-021-16034-3
    This experimental research was conducted to study the combined effect of agricultural by-product wastes on the properties of concrete. The coconut shell ash (CSA) was utilized to substitute cement content ranging from 0 to 20% by weight of total binder and sugarcane bagasse ash (SCBA) to substitute fine aggregates (FA) ranging from 0 to 40% by weight of total FA. In this regard, a total of 300 concrete specimens (cylinders and cubes) were prepared using 1:1.5:3 mix proportions with a 0.52 water-binder ratio. The study investigated the workability, density, permeability, and mechanical properties in terms of compressive and splitting tensile strengths. Additionally, the total embodied carbon for all mix proportions was calculated. It was observed that with an increase in CSA and SCBA contents, the workability, density, and permeability reduced significantly. Due to CSA and SCBA being pozzolanic materials, a gain in compressive and splitting tensile strengths was observed for certain concrete mixes, after which the strength decreased. The increase in embodied carbon of SCBA increased the total embodied carbon of concrete; however, it can be said that C15S40 which consists of 15% CSA and 40% SCBA is the optimum mix that achieved 28.75 MPa and 3.05 MPa compressive and tensile strength, respectively, a reduction of 4% total embodied carbon.
    Matched MeSH terms: Saccharum*
  4. Channa SH, Mangi SA, Bheel N, Soomro FA, Khahro SH
    Environ Sci Pollut Res Int, 2022 Jan;29(3):3555-3564.
    PMID: 34387820 DOI: 10.1007/s11356-021-15877-0
    Globally, concrete is widely implemented as a construction material and is progressively being utilized because of growth in urbanization. However, limited resources and gradual depravity of the environment are forcing the research community to obtain alternative materials from large amounts of agro-industrial wastes as a partial replacement for ordinary cement. Cement is a main binding resource in concrete production. To reduce environmental problems associated with waste, this study considered the recycling of agro-industrial wastes, such as sugarcane bagasse ash (SCBA), rice husk ash (RHA), and others, into cement, and to finally bring sustainable and environmental-friendly concrete. This study considered 5%, 10%, and 15% of SBCA and RHA individually to replace ordinary Portland cement (OPC) by weight method then combined both ashes as 10%, 20%, and 30% to replace OPC to produce sustainable concrete. It was experimentally declared that the strength performance of concrete was reduced while utilizing SCBA and RHA individually and combined as supplementary cementitious material (SCM) at 7, 28, 56, and 90 days, respectively. Moreover, the initial and final setting time is increased as the quantity of replacement level of OPC with SCBA and RHA separates and together as SCM in the mixture. Based on experimental findings, it was concluded that the use of 5% of SCBA and 5% of RHA as cement replacement material individually or combined in concrete could provide appropriate results for structural applications in concrete.
    Matched MeSH terms: Saccharum*
  5. Bheel N, Ali MOA, Tafsirojjaman, Khahro SH, Keerio MA
    Environ Sci Pollut Res Int, 2022 Jan;29(4):5224-5239.
    PMID: 34417691 DOI: 10.1007/s11356-021-15954-4
    In recent years, the research direction is shifted toward introducing new supplementary cementitious materials (SCM) in lieu of in place of Portland cement (PC) in concrete as its production emits a lot of toxic gases in the atmosphere which causes environmental pollution and greenhouse gases. SCM such as sugarcane bagasse ash (SCBA), metakaolin (MK), and millet husk ash (MHA) are available in abundant quantities and considered as waste products. The primary aim of this experimental study is to investigate the effect of SCBA, MK, and MHA on the fresh and mechanical properties of concrete mixed which contributes to sustainable development. A total of 228 concrete specimens were prepared with targeted strength of 25MPa at 0.52 water-cement ratio and cured at 28 days. It is found that the compressive strength and split tensile strength were enhanced by 17% and 14.28%, respectively, at SCBA4MK4MHA4 (88% PC, 4% SCBA, 4% MK, and 4% MHA) as ternary cementitious material (TCM) in concrete after 28 days. Moreover, the permeability and density of concrete are found to be reduced when SCBA, MK, and MHA are used separately and combined as TCM increases in concrete at 28 days, respectively. The results showed that the workability of the fresh concrete was decreased with the increase of the percentage of SCBA, MK, and MHA separately and together as TCM in concrete.
    Matched MeSH terms: Saccharum*
  6. Ong P, Jian J, Li X, Yin J, Ma G
    PMID: 37804706 DOI: 10.1016/j.saa.2023.123477
    Spectroscopy in the visible and near-infrared region (Vis-NIR) region has proven to be an effective technique for quantifying the chlorophyll contents of plants, which serves as an important indicator of their photosynthetic rate and health status. However, the Vis-NIR spectroscopy analysis confronts a significant challenge concerning the existence of spectral variations and interferences induced by diverse factors. Hence, the selection of characteristic wavelengths plays a crucial role in Vis-NIR spectroscopy analysis. In this study, a novel wavelength selection approach known as the modified regression coefficient (MRC) selection method was introduced to enhance the diagnostic accuracy of chlorophyll content in sugarcane leaves. Experimental data comprising spectral reflectance measurements (220-1400 nm) were collected from sugarcane leaf samples at different growth stages, including seedling, tillering, and jointing, and the corresponding chlorophyll contents were measured. The proposed MRC method was employed to select optimal wavelengths for analysis, and subsequent partial least squares regression (PLSR) and Gaussian process regression (GPR) models were developed to establish the relationship between the selected wavelengths and the measured chlorophyll contents. In comparison to full-spectrum modelling and other commonly employed wavelength selection techniques, the proposed simplified MRC-GPR model, utilizing a subset of 291 selected wavelengths, demonstrated superior performance. The MRC-GPR model achieved higher coefficient of determination of 0.9665 and 0.8659, and lower root mean squared error of 1.7624 and 3.2029, for calibration set and prediction set, respectively. Results showed that the GPR model, a nonlinear regression approach, outperformed the PLSR model.
    Matched MeSH terms: Saccharum*
  7. Uke A, Nakazono-Nagaoka E, Chuah JA, Zain NA, Amir HG, Sudesh K, et al.
    J Environ Manage, 2021 Oct 01;295:113050.
    PMID: 34198177 DOI: 10.1016/j.jenvman.2021.113050
    Oil palm trunks (OPT) are logged for replantation and the fiber residues are disposed of into the palm plantation area. The fiber residues are expected to increase soil fertility through recycling of carbon and minerals via fiber decomposition. This study investigated the effects of OPT fiber disposal and other lignocellulosic biomass on plant growth and microbial diversity in the soil environment. Four treatment plots were tested: (A) soil+OPT fiber (1:20), (B) soil+sugarcane bagasse (1:20), (C) soil+cellulose powder (1:20), and (D) unamended soil as a negative control. Low plant height, decreased chlorophyll content, and low biomass was observed in corn grown on soil mixed with OPT fiber, cellulose, and sugarcane bagasse, when compared with those of the control. The plants grown with OPT fiber were deficient in total nitrogen and magnesium when compared with those without fiber amendment, which suggested that nitrogen and minerals in soil might be taken up by changing microflora because of the OPT fibers presence. To confirm differences in the soil microflora, metagenomics analysis was performed on untreated soil and soil from each lignocellulose treatment. The microflora of soils mixed with OPT fiber, cellulose and sugarcane bagasse revealed substantial increases in bacteria such as families Cytophagaceae and Oscillospiraceae, and two major fungal genera, Trichoderma and Trichocladium, that are involved in lignocellulose degradation. OPT fiber resulted in a drastic increase in the ratios and amounts of Trichocladium in the soil when compared with those of cellulose and sugarcane bagasse. These results indicate that unregulated disposal of OPT fiber into plantation areas could result in nutrient loss from soil by increasing the abundance of microorganisms involved in lignocellulose decomposition.
    Matched MeSH terms: Saccharum*
  8. Hajar-Azhari S, Hafiz Abd Rahim M, Razid Sarbini S, Muhialdin BJ, Olusegun L, Saari N
    Food Res Int, 2021 11;149:110677.
    PMID: 34600679 DOI: 10.1016/j.foodres.2021.110677
    Fructooligosaccharides can be produced by direct enzymatic conversion from sucrose-rich sugarcane syrup (SS) consisting of 58.93% sucrose yielding 21.28 g FOS/100 g sucrose. This study evaluated the prebiotic effect of unpurified/purified SS containing FOS for the modulation of the human intestinal microbial composition and short-chain fatty acid production. The unpurified and purified FOS substrates, which were a mixture of 1-kestose, nystose and 1F-fructosylnystose, were supplemented into human faecal culture using a pH-controlled batch fermentation system and significantly increased the Bifidobacterium counts after 5 h fermentation, while Bacteroides/Prevotella counts were highest throughout 24 h fermentation. Meanwhile, Lactobacillus/Enterococcus exhibited a slight increase after 5 h fermentation before reaching a plateau afterwards. The steady Bacteroides/Prevotella growth and increased Bifidobacterium population promoted an increase in the production of short-chain fatty acids acetate (58 ± 2.70 mM), propionate (9.19 ± 5.94 mM) and butyrate (7.15 ± 2.28 mM). These results provide evidence that representative gut microbiota could utilise the enzymatically synthesised FOS to generate short-chain fatty acids as metabolites in pH-controlled conditions, thus FOS from SS are a potential prebiotic ingredient for foods and health drinks.
    Matched MeSH terms: Saccharum*
  9. Ong P, Jian J, Li X, Zou C, Yin J, Ma G
    PMID: 37356390 DOI: 10.1016/j.saa.2023.123037
    The proliferation of pathogenic fungi in sugarcane crops poses a significant threat to agricultural productivity and economic sustainability. Early identification and management of sugarcane diseases are therefore crucial to mitigate the adverse impacts of these pathogens. In this study, visible and near-infrared spectroscopy (380-1400 nm) combined with a novel wavelength selection method, referred to as modified flower pollination algorithm (MFPA), was utilized for sugarcane disease recognition. The selected wavelengths were incorporated into machine learning models, including Naïve Bayes, random forest, and support vector machine (SVM). The developed simplified SVM model, which utilized the MFPA wavelength selection method yielded the best performances, achieving a precision value of 0.9753, a sensitivity value of 0.9259, a specificity value of 0.9524, and an accuracy of 0.9487. These results outperformed those obtained by other wavelength selection approaches, including the selectivity ratio, variable importance in projection, and the baseline method of the flower pollination algorithm.
    Matched MeSH terms: Saccharum*
  10. Buthiyappan A, Gopalan J, Abdul Raman AA
    J Environ Manage, 2019 Nov 01;249:109323.
    PMID: 31400589 DOI: 10.1016/j.jenvman.2019.109323
    This present research aims to synthesize and investigate the adsorption potential of sugarcane bagasse (SCB) impregnated with iron oxide (Fe3O4) for dye removal. The surface morphology and functional groups of the newly developed adsorbent (ISCB) were studied using Scanning Electron Microscopy/Energy-dispersive X-ray spectroscopy (SEM/EDX), Fourier transforms infrared spectroscopy (FTIR), and X-ray powder diffraction (XRD) analysis. The effects of the operating parameters, including initial dye concentration, adsorbent dosage, contact time and initial pH of the dye solution on the adsorption efficiency were investigated to identify an optimal condition. The characterization of SEM-EDX and FTIR analyses shows that ISCB has a porous structure and carbon-containing functional groups. The adsorption result revealed that ISCB removed 93.7% of dye, 88.8% of color and had a dye adsorption capacity of 7.2 mg/g within 6 h of contact time using 0.7 g/L of ISCB at pH 8.4. The result obtained fitted well for Langmuir isotherms, and adsorption process followed the pseudo-second-order kinetic model. In conclusion, this study proved that ISCB has the potential to be used as an effective and low-cost adsorbent to remove dyes from wastewater.
    Matched MeSH terms: Saccharum*
  11. Nugraha MW, Zainal Abidin NH, Supandi, Sambudi NS
    Chemosphere, 2021 Aug;277:130300.
    PMID: 33774232 DOI: 10.1016/j.chemosphere.2021.130300
    In this present study, the tungsten oxide/amino-functionalized sugarcane bagasse derived-carbon quantum dots (WO3/N-CQDs) composite has successfully been prepared through a simple mixing process. The WO3 was synthesized through a precipitation method, and CQDs were amino-functionalized using ethylenedinitrilotetraacetic acid (EDTA) and ethylenediamine (EDA) through one-pot hydrothermal method. It is revealed that N-CQDs incorporation into WO3 alters the bandgap energy, crystallinity, surface area, and photoluminescence (PL) properties. The produced composites exhibit higher monoclinic WO3 crystallinity, larger surface area, lower bandgap energy and quenched photoluminescence intensity. The as-prepared WO3/N-CQDs composites exhibit better adsorption and photocatalytic degradation performance of methylene blue (MB) than the pristine WO3. It shows that the combination of N-CQDs and WO3 enhanced visible light absorption, by lowering the bandgap energy of WO3 from 2.175 to 1.495 eV. The best performance composite is WO3/N-CQDs EDA 2.5% with an efficiency of 96.86%, removal rate constant of 0.02017/min, and chemical oxidation demand (COD) removal efficiency achieved 84.61%. Moreover, the WO3/N-CQDs EDA 2.5% shows a significant photocatalytic activity even at higher MB initial concentration with 92.93% removal for 50 ppm MB. Subsequently, the composite also has good stability after a sequential 3-times cycle of degradation with 86.85% removal. The increasing photocatalytic performance is affected by the quenching effect of PL and lower bandgap energy. The lower intensity of the PL indicates the reduced charge carrier recombination resulting in increased photocatalytic activity. The combination of N-CQDs and WO3 resulted in improved photodegradation, which shows its significant potential to be utilized for wastewater treatment.
    Matched MeSH terms: Saccharum*
  12. Umar MF, Rafatullah M, Abbas SZ, Ibrahim MNM, Ismail N
    J Hazard Mater, 2021 10 05;419:126469.
    PMID: 34192640 DOI: 10.1016/j.jhazmat.2021.126469
    Xylene, a recalcitrant compound present in wastewater from activities of petrochemical and chemical industries causes chronic problems for living organisms and the environment. Xylene contaminated wastewater may be biodegraded through a benthic microbial fuel cell (BMFC) as seen in this study. Xylene was oxidized into intermediate 3-methyl benzoic acid and entirely converted into non-toxic carbon dioxide. The highest voltage of the BMFC reactor was generated at 410 mV between 23 and 90 days when cell potential was 1 kΩ. The reactor achieved a maximum power density of about 63 mW/m2, and a current of 0.4 mA which was optimized from variable resistance (20 Ω - 1 kΩ). However, the maximum biodegradation efficiency of the BMFC was at 87.8%. The cyclic voltammetry curve helped to determine that the specific capacitance was 0.124 F/g after 30 days of the BMFC operation. Furthermore, the fitting equivalent circuit was observed with the help of Nyquist plot for calculating overall internal resistance of 65.82 Ω on 30th day and 124.5 Ω on 80th day. Staphylococcus edaphicus and Staphylococcus sparophiticus were identified by 16S rRNA sequencing as the dominant species in the control and BMFC electrode, presumably associated with xylene biodegradation.
    Matched MeSH terms: Saccharum*
  13. Mukhtar K, Nabi BG, Arshad RN, Roobab U, Yaseen B, Ranjha MMAN, et al.
    Ultrason Sonochem, 2022 Nov;90:106194.
    PMID: 36242792 DOI: 10.1016/j.ultsonch.2022.106194
    Sugarcane juice (Saccharum officinarum) is a proven nutritious beverage with high levels of antioxidants, polyphenols, and other beneficial nutrients. It has recently gained consumer interest due to its high nutritional profile and alkaline nature. Still, high polyphenolic and sugar content start the fermentation in juice, resulting in dark coloration. Lately, some novel techniques have been introduced to extend shelf life and improve the nutritional value of sugarcane juice. The introduction of such processing technologies is beneficial over conventional processes and essential for producing chemical-free, high-quality, fresh juices. The synergistic impact of these novel technologies is also advantageous for preserving sugarcane juice. In literature, novel thermal, non-thermal and hurdle technologies have been executed to preserve sugarcane juice. These technologies include high hydrostatic pressure (HHP), ultrasound (US), pulsed electric field (PEF), ultraviolet irradiation (UV), ohmic heating (OH), microwave (MW), microfludization and ozone treatment. This review manifests the impact of novel thermal, non-thermal, and synergistic technologies on sugarcane juice processing and preservation characteristics. Non-thermal techniques have been successfully proved effective and showed better results than novel thermal treatments. Because they reduced microbial load and retained nutritional content, while thermal treatments degraded nutrients and flavor of sugarcane juice. Among non-thermal treatments, HHP is the most efficient technique for the preservation of sugarcane juice while OH is preferable in thermal techniques due to less nutritional loss.
    Matched MeSH terms: Saccharum*
  14. Kee WC, Wong YS, Ong SA, Lutpi NA, Sam ST, Dahalan FA, et al.
    Environ Sci Pollut Res Int, 2023 May;30(24):65364-65378.
    PMID: 37081370 DOI: 10.1007/s11356-023-27046-6
    Sugarcane vinasse has been reported as a high strength industrial wastewater that could cause severe environmental pollution due to its complex and bio-refractory compounds. Thus, the combined coagulation and sequencing batch biofilm reactor (SBBR) system was employed for the sugarcane vinasse treatment. This study aims to determine the recommended conditions of various parameters under coagulation and SBBR and investigate the effectiveness of combined processes. First, the approach of the coagulation process could achieve the maximum COD reduction and decolorization efficiencies of 79.0 ± 3.4% and 94.1 ± 1.9%, respectively, under the recommended conditions. Next, SBBR as an integrated biofilm reactor showed excellent synergistic biodegradability, removing 86.6 ± 4.3% COD concentration and 94.6 ± 3.8% color concentration at 3.0 g·COD/L of substrate loading concentration. The kinetic studies of SBBR revealed that the first-order kinetic model was the best fit for COD reduction efficiency. In contrast, the second-order kinetic model was the best fit for decolorization efficiency. The SBBR reaction was further investigated by ultraviolet-visible spectrophotometry (UV-Vis). In the combined processes, SBBR followed by the coagulation process (SBBR-CP) showed greater COD reduction and decolorization efficiencies (97.5 ± 0.3 and 99.4 ± 0.1%) when compared to the coagulation process followed by SBBR (CP-SBBR). This study demonstrated the removal performance and potential application of the combined sequential process to produce effluent that can be reused for bioethanol production and fertigation. This finding provides additional insight for developing effective vinasse treatment using combined chemical and biological processes.
    Matched MeSH terms: Saccharum*
  15. Azlan A, Sultana S, Mahmod II
    Molecules, 2023 May 28;28(11).
    PMID: 37298880 DOI: 10.3390/molecules28114403
    The health benefits of sugar cane products are attributed to certain antioxidant compounds in plant materials. The presence of antioxidants in plant materials depends on the extraction method in terms of yield and the number of phenolic compounds identified. This study was carried out to evaluate the performance of the three extraction methods, which were selected from previous studies to show the effect of the extraction method on the content of antioxidant compounds in different types of sugar. This study also evaluates the potential of different sugar extracts in anti-diabetic activity based on in vitro assays (α-glucosidase and α-amylase). The results showed that sugar cane extracted with acidified ethanol (1.6 M HCl in 60% ethanol) was the best condition to extract a high yield of phenolic acids compared to other methods. Among the three types of sugar, less refined sugar (LRS) showed the highest yield of phenolic compounds, 57.72 µg/g, compared to brown sugar (BS) and refined sugar (RS) sugar, which were at 42.19 µg/g and 22.06 µg/g, respectively. Whereas, among the sugar cane derivatives, LRS showed minor and BS moderate inhibition towards α-amylase and α-glucosidase activity compared to white sugar (RS). Thus, it is suggested that sugar cane extracted with acidified ethanol (1.6 M HCl in 60% ethanol) is the optimum experimental condition for antioxidant content determination and provides a basis for further exploitation of the health-beneficial resources of the sugarcane products.
    Matched MeSH terms: Saccharum*
  16. Yoon LW, Ngoh GC, Chua AS
    Enzyme Microb Technol, 2013 Sep 10;53(4):250-6.
    PMID: 23931690 DOI: 10.1016/j.enzmictec.2013.05.005
    This study examined the potential of untreated and alkali-pretreated sugarcane bagasse (SCB) in cellulase, reducing sugar (RS) and fungal biomass production via solid state fermentation (SSF) using Pycnoporus sanguineus. The impact of the composition, structure and cellulase adsorption ability of SCB on the production of cellulase, RS and fungal biomass was investigated. From the morphological and compositional analyses, untreated SCB has relatively more structural changes with a higher percentage of depolymerisation on the cellulose, hemicellulose and lignin content compared to alkali-pretreated SCB. Thus, untreated SCB favoured the production of cellulase and fungal biomass whereas alkali-pretreated SCB yielded a higher amount of RS. The composition and morphology of untreated SCB did not encourage RS production and this suggested that RS produced during SSF might be consumed in a faster rate by the more abundantly grown fungus. Besides that, alkali-pretreated SCB with higher cellulase adsorption ability could have adsorbed the cellulase produced and resulted in a lower cellulase titre. In short, the production of specific bioproducts via SSF is dependent on the structure and composition of the substrate applied.
    Matched MeSH terms: Saccharum/metabolism*; Saccharum/ultrastructure; Saccharum/chemistry
  17. Chen JH, Liu L, Lim PE, Wei D
    Bioprocess Biosyst Eng, 2019 Jul;42(7):1129-1142.
    PMID: 30919105 DOI: 10.1007/s00449-019-02110-z
    Microalgal lipid production by Chlorella protothecoides using sugarcane bagasse hydrolysate was investigated in this study. First, maximum glucose and reducing sugar concentrations of 15.2 and 27.0 g/L were obtained in sugarcane bagasse hydrolysate (SCBH), and the effects of different percentages of glucose and xylose on algal cultivation were investigated. Afterwards, SCBH was used as a carbon source for the cultivation of C. protothecoides and higher biomass concentration of 10.7 g/L was achieved. Additionally, a large amount of fatty acids, accounting up to 16.8% of dry weight, were accumulated in C. protothecoides in the nitrogen-limited (0.1-1 mmol/L) culture. Although SCBH inhibited fatty acid accumulation to a certain degree and the inhibition was aggravated by nitrogen starvation, SCBH favored microalgal cell growth and fatty acid production. The present study is of significance for the integration of cost-effective feedstocks production for biodiesel with low-cost SCBH as well as environmentally friendly disposal of lignocellulosic wastes.
    Matched MeSH terms: Saccharum/chemistry*
  18. Naggar AH, Dhmees A, Seaf-Elnasr TA, Chong KF, Ali GAM, Ali HM, et al.
    Environ Sci Pollut Res Int, 2024 Jan;31(3):3872-3886.
    PMID: 38093080 DOI: 10.1007/s11356-023-31453-0
    The current investigation concerns with preparation eco-friendly and cost-effective adsorbent (mesoporous silica nanoparticles (SBL)) based on black liquor (BL) containing lignin derived from sugarcane bagasse and combining it with sodium silicate derived from blast furnace slag (BFS) for thorium adsorption. Thorium ions were adsorbed from an aqueous solution using the synthesized bio-sorbent (SBL), which was then assessed by X-ray diffraction, BET surface area analysis, scanning electron microscopy with energy dispersive X-ray spectroscopy (EDX), and Fourier transforms infrared spectroscopy (FTIR). Th(IV) sorption properties, including the pH effect, uptake rate, and sorption isotherms across various temperatures were investigated. The maximum sorption capacity of Th(IV) on SBL is 158.88 mg/L at pH value of 4328 K, and 60 min contact time. We demonstrated that the adsorption processes comport well with pseudo-second-order and Langmuir adsorption models considering the kinetics and equilibrium data. According to thermodynamic inspections results, the Th(IV) adsorption process exhibited endothermic and random behavior suggested by positive ΔH° and ΔS° values, while the negative ΔG° values indicated a spontaneous sorption process. The maximum Th(IV) desorption from the loaded SBL (Th/SBL) was carried out at 0.25 M of NaHCO3 and 60 min of contact. Sorption/desorption processes have five successive cycles. Finally, this study suggests that the recycling of BFS and BL can be exploited for the procurement of a promising Th(IV) adsorbents.
    Matched MeSH terms: Saccharum*
  19. Kalhori N, Nulit R, Go R
    Protein J, 2013 Oct;32(7):551-9.
    PMID: 24132392 DOI: 10.1007/s10930-013-9516-z
    Pentose phosphate pathway (PPP) composed of two functionally-connected phases, the oxidative and non-oxidative phase. Both phases catalysed by a series of enzymes. Transketolase is one of key enzymes of non-oxidative phase in which transfer two carbon units from fructose-6-phosphate to erythrose-4-phosphate and convert glyceraldehyde-3-phosphate to xylulose-5-phosphate. In plant, erythrose-4-phosphate enters the shikimate pathway which is produces many secondary metabolites such as aromatic amino acids, flavonoids, lignin. Although transketolase in plant system is important, study of this enzyme is still limited. Until to date, TKT genes had been isolated only from seven plants species, thus, the aim of present study to isolate, study the similarity and phylogeny of transketolase from sugarcane. Unlike bacteria, fungal and animal, PPP is complete in the cytosol and all enzymes are found cytosolic. However, in plant, the oxidative phase found localised in the cytosol but the sub localisation for non-oxidative phase might be restricted to plastid. Thus, this study was conducted to determine subcellular localization of sugarcane transketolase. The isolation of sugarcane TKT was done by reverse transcription polymerase chain reaction, followed by cloning into pJET1.2 vector and sequencing. This study has isolated 2,327 bp length of sugarcane TKT. The molecular phylogenetic tree analysis found that transketolase from sugarcane and Zea mays in one group. Classification analysis found that both plants showed closer relationship due to both plants in the same taxon i.e. family Poaceae. Target P 1.1 and Chloro P predicted that the compartmentation of sugarcane transketolase is localised in the chloroplast which is 85 amino acids are plant plastid target sequence. This led to conclusion that the PPP is incomplete in the cytosol of sugarcane. This study also found that the similarity sequence of sugarcane TKT closely related with the taxonomy plants.
    Matched MeSH terms: Saccharum/classification; Saccharum/enzymology*; Saccharum/genetics
  20. Hassan H, Lim JK, Hameed BH
    Bioresour Technol, 2019 Mar 28;284:406-414.
    PMID: 30965196 DOI: 10.1016/j.biortech.2019.03.137
    This study investigated the catalytic co-pyrolysis of sugarcane bagasse (SCB) and waste high-density polyethylene (HDPE) over faujasite-type zeolite derived from electric arc furnace slag (FAU-EAFS) in a fixed-bed reactor. The effects of reaction temperature, catalyst-to-feedstock ratio, and HDPE-to-SCB ratio on product fractional yields and chemical compositions were discussed. The co-pyrolysis of SCB and HDPE over FAU-EAFS increased the liquid yield and enhanced the quality of bio-oil. The maximum bio-oil (68.56 wt%) and hydrocarbon yield (74.55%) with minimum yield of oxygenated compounds (acid = 0.57% and ester = 0.67%) were achieved under the optimum experimental conditions of catalyst-to-feedstock ratio of 1:6, HDPE-to-SCB ratio of 40:60, and temperature of 500 °C. The oil produced by catalytic co-pyrolysis had higher calorific value than the oil produced by the pyrolysis of SCB alone.
    Matched MeSH terms: Saccharum
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links