Displaying publications 1 - 20 of 224 in total

Abstract:
Sort:
  1. AWANG R, SITI N.H.M. DAUD, CHI CY, MOHAMMAD HAFIZUDDIN HAJI JUMALI, ZALITA Z
    Sains Malaysiana, 2013;42:1663-1670.
    Filem nipis ZnO terdop Ga (ZnO:Ga) disediakan menggunakan teknik sol-gel dan salutan berputar. Ga didopkan kepada ZnO dengan peratusan berat (wt. %) yang berbeza iaitu 0, 2, 4, 6 dan 8 wt. %. Kesan pengedopan Ga ke atas struktur dan sifat optik filem nipis ZnO dikaji. Pencirian struktur filem nipis ini dilakukan menggunakan kaedah pembelauan sinar-X (XRD), mikroskop imbasan elektron pancaran medan (FESEM) dan mikroskop daya atom (AFM). Pencirian sifat optik filem nipis pula dilakukan menggunakan spektroskopi ultraungu cahaya nampak (UV-VIS) dan fotoluminesen (PL). Ujian XRD mengesahkan kesemua sampel berstruktur wurtzit. Saiz kristalit ZnO mengecil dengan peningkatan peratusan berat Ga seterusnya mengurangkan kekasaran permukaan filem. Pengedopan Ga menunjukkan peratus transmisi cahaya pada panjang gelombang 300 - 380 nm bertambah berbanding filem nipis ZnO tanpa dop. Nilai jurang tenaga optik, Eg dan keamatan PL filem nipis ZnO meningkat apabila pengedopan Ga dilakukan. Hasil kajian ini menunjukkan saiz kristalit yang lebih kecil memberi kesan ke atas sifat optik sampel pada peratus pengedopan Ga 0-6%. Pada peratus pengedopan Ga yang lebih tinggi, kesan transformasi struktur menjadi lebih dominan dalam mempengaruhi nilai Eg.
    Matched MeSH terms: Zinc Oxide
  2. Pang WY, Ahmad AL, Zaulkiflee ND
    J Environ Manage, 2019 Nov 01;249:109358.
    PMID: 31450197 DOI: 10.1016/j.jenvman.2019.109358
    The aim of this study is to evaluate the performance and antifouling properties of polyethersulfone (PES) membrane incorporated with dual nanofiller, zinc oxide (ZnO) and multi-walled carbon nanotube (MWCNT). The synergistic effect of the these nanofillers in PES membrane is studied by blending different ratio of ZnO/MWCNT nanofiller into the PES membrane. The fabricated membranes were characterized in terms of cross-section and surface morphology, surface hydrophilicity, pore size and porosity. The filtration performance of the membranes was tested using 50 mg/L humic acid (HA) solution as model solution. SEM image and gravimetric evaluation reported that the incorporation of both MWCNT and ZnO into the PES membrane improved porosity significantly up to 46.02%. Lower water contact angle of PES membrane incorporated with equal ratio of MWCNT and ZnO (PES 3) revealed that it has neat PES membrane properties and more hydrophilic membrane surface than single filler. PES 3 outperform other membranes with excellent HA permeate flux of 40.00 L/m2.h and rejection of 88.51%. Due to hydrophilic membrane surface, PES 3 membrane demonstrate efficient antifouling properties with lower relative flux reduction (RFR) and higher flux recovery ratio (FRR). PES 3 also showed notable antibacterial properties with less bacterial attached to the membrane compared to neat PES membrane (PES 0).
    Matched MeSH terms: Zinc Oxide*
  3. Haarindraprasad R, Gopinath SCB, Veeradassan P
    Biotechnol Appl Biochem, 2022 Dec;69(6):2698-2712.
    PMID: 34997977 DOI: 10.1002/bab.2316
    A "Janus particle" refers to the production of two materials in a single system and shows a difference in physical characteristics, and two surfaces participate in the formation with different chemistries. This research generated the Janus using a hybrid of zinc oxide (ZnO) and gold (Au) on the sensor surface toward making high-performance DNA sensors. The Janus ZnO/Au-textured film was synthesized via the one-step sol-gel method, which involves a suitable ratio of a mixture of ZnO sol seed solution. The synthesized Janus ZnO/Au-textured film undergoes a low-temperature aqueous hydrothermal route to synthesize quasi-one-dimensional nanowires. The average grain size in the Janus ZnO/Au nanotextured wire was 41.60 nm. The fabricated nanotextured wire was further optimized by tuning the thickness and characterized by XRD and high-resolution microscopy. Electrical characterization was conducted on the Janus ZnO/Au nanotextured wire coupled with an interdigitated electrode sensor to detect the specific leptospirosis DNA strand. The generated device is capable of detecting lower DNA concentration at 1 × 10-13 M with a sensitivity of 8.54 MΩ M-1 cm-2 . The high performance is attained on linear concentrations of 10-6 -10-13 M with the determination coefficient, "I = 135437.63C-3609.07" R2 = 0.9551. A potential strategy is proposed as a base for developing different high-performance sensors.
    Matched MeSH terms: Zinc Oxide*
  4. Mohamed Isa ED, Che Jusoh NW, Hazan R, Shameli K
    Environ Sci Pollut Res Int, 2021 Feb;28(5):5774-5785.
    PMID: 32975756 DOI: 10.1007/s11356-020-10939-1
    One of mankind's biggest concerns is water pollution. Textile industry emerged as one of the main contributors with dyes as the main pollutant. Presence of dyes in water is very dangerous due to their toxicity; thus, it is important to remove them from water. In these recent years, heterogeneous advance oxidation process surfaced as a possible dyes' removal technique. This process utilizes semiconductor as photocatalyst to degrade the dyes in presence of light and zinc oxide (ZnO) appears to be a promising photocatalyst for this process. In this study, pullulan, a biopolymer, was used to produce porous ZnO microflowers (ZnO-MFs) through green synthesis via precipitation method. The effects of pullulan's amount on the properties of ZnO-MFs were investigated. The ZnO-MF particle size decreased with the increased of pullulan amount. Interestingly, formation of pores occurred in presence of pullulan. The synthesized ZnO-MFs have the surface area ranging from 6.22 to 25.65 m2 g-1 and pore volume up to 0.1123 cm3 g-1. The ZnO-MF with the highest surface area was chosen for photocatalytic degradation of methyl orange (MO). The highest degradation occurred in 300 min with 150 mg catalyst dosage, 10 ppm initial dye concentration, and pH 7 experimental conditions. However, through comparison of photodegradation of MO with all synthesized ZnO-MFs, 25PZ exhibited the highest degradation rate. This shows that photocatalytic activity is not dependent on surface area alone. Based on these results, ZnO-MF has the potential to be applied in wastewater treatment. However, further improvement is needed to increase its photocatalytic activity.
    Matched MeSH terms: Zinc Oxide*
  5. Isa EDM, Jusoh NWC, Rodzi AAM
    Environ Sci Pollut Res Int, 2023 Nov;30(55):116921-116933.
    PMID: 37178288 DOI: 10.1007/s11356-023-27576-z
    The scarcity of water leads to research nowadays to focus on techniques for treating wastewater. Photocatalysis emerged as a technique of interest due to its nature of friendliness. It utilizes light and catalyst to degrade the pollutants. One of the popular catalysts to be used is zinc oxide (ZnO), but its usage is limited due to the high recombination rate of electron-hole pair. Herein, in this study, ZnO is modified with graphitic carbon nitride (GCN), and the GCN loading amount was varied to study the impact on photocatalytic degradation of mixed dye solution. To the best of our knowledge, this is the first work that reports on the degradation of mixed dye solution using modified ZnO with GCN. Structural analysis showed that GCN is present in the composites which proves the success of the modification. Photocatalytic activity revealed that the composite with 5 wt% loading of GCN showed the best activity at a catalyst dosage of 1 g/L with degradation rates of 0.0285, 0.0365, 0.0869, and 0.1758 min-1 for methyl red, methyl orange, rhodamine B, and methylene blue dyes, respectively. This observation is expected due to the formation of heterojunction between ZnO and GCN which creates a synergistic effect and thus led to an improvement in the photocatalytic activity. Based on these results, ZnO modified with GCN has a good potential to be used in the treatment of textile wastewater which consists of various dye mixtures.
    Matched MeSH terms: Zinc Oxide*
  6. Ayob MTM, Mohd HMK, Abdul Rahman I, Mohamed F, Hidzir NM, Radiman S
    Sains Malaysiana, 2016;45:1265-1273.
    Kami melaporkan hasil kajian terhadap nanokomposit Ag-ZnO dengan nisbah berat yang berbeza bagi Ag:ZnO (0:10,
    7:10 & 25:10) yang telah disediakan melalui kaedah sonokimia. Kajian fotomangkin terhadap nanokomposit Ag-ZnO
    menunjukkan peningkatan kecekapan fotomangkin terhadap foto-penguraian larutan akues metilena biru berbanding
    nanobahan ZnO tulen di bawah penyinaran cahaya nampak. Sampel Ag-ZnO pada nisbah 7:10 menunjukkan aktiviti
    fotomangkin terbaik dan mencapai kadar penguraian sehingga 94% bagi tempoh masa penguraian selama 80 min,
    diikuti 86% bagi sampel ZnO tulen dengan menggunakan kaedah yang sama. Morfologi, struktur bahan, sifat optik dan
    kehabluran bagi nanokomposit Ag-ZnO juga dibincangkan menerusi data yang diperoleh melalui mikroskop elektron
    transmisi, spektroskopi ultralembayung-cahaya nampak dan difraktometer analisis sinar-X. Hasil kajian menunjukkan
    bahawa dengan penambahan zarah Ag kepada ZnO telah meningkatkan kadar serapan cahaya bagi ZnO di kawasan
    cahaya nampak dan meningkatkan kadar pemisahan cas foto-aruhan bagi menghasilkan rawatan air tercemar pewarna
    yang lebih baik.
    Matched MeSH terms: Zinc Oxide
  7. Ahmad MB, Fatehi A, Zakaria A, Mahmud S, Mohammadi SA
    Int J Mol Sci, 2012;13(12):15640-52.
    PMID: 23443085 DOI: 10.3390/ijms131215640
    This study focuses on the fabrication and electrical characterization of a polymer composite based on nano-sized varistor powder. The polymer composite was fabricated by the melt-blending method. The developed nano-composite was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), field emission scanning electron microscopy (FeSEM), and energy-dispersive X-ray spectroscopy (EDAX). The XRD pattern revealed the crystallinity of the composite. The XRD study also showed the presence of secondary phases due to the substitution of zinc by other cations, such as bismuth and manganese. The TEM picture of the sample revealed the distribution of the spherical, nano-sized, filler particles throughout the matrix, which were in the 10-50 nm range with an average of approximately 11 nm. The presence of a bismuth-rich phase and a ZnO matrix phase in the ZnO-based varistor powder was confirmed by FeSEM images and EDX spectra. From the current-voltage curves, the non-linear coefficient of the varistor polymer composite with 70 wt% of nano filler was 3.57, and its electrical resistivity after the onset point was 861 KΩ. The non-linear coefficient was 1.11 in the sample with 100 wt% polymer content. Thus, it was concluded that the composites established a better electrical non-linearity at higher filler amounts due to the nano-metric structure and closer particle linkages.
    Matched MeSH terms: Zinc Oxide/chemistry*
  8. Pillai P, Dharaskar S, Khalid M
    Chemosphere, 2021 Dec;284:131317.
    PMID: 34216929 DOI: 10.1016/j.chemosphere.2021.131317
    The current novel work presents the optimization of factors affecting defluoridation by Al doped ZnO nanoparticles using response surface methodology (RSM). Al doped ZnO nanoparticles were synthesized by the sol-gel method and validated by FTIR, XRD, TEM/EDS, TGA, BET, and particle size analysis. Moreover, a central composite design (CCD) was developed for the experimental study to know the interaction between Al doped ZnO adsorbent dosage, initial concentration of fluoride, and contact time on fluoride removal efficiency (response) and optimization of the process. Analysis of variance (ANOVA) was achieved to discover the importance of the individual and the effect of variables on the response. The model predicted that the response significantly correlated with the experimental response (R2 = 0.97). Among the factors, the effect of adsorbent dose and contact time was considered to have more influence on the response than the concentration. The optimized process parameters by RSM presented the adsorbent dosage: 0.005 g, initial concentration of fluoride: 1.5 g/L, and contact time: 5 min, respectively. Kinetic, isotherm, and thermodynamic studies were also investigated. The co-existing ions were also studied. These results demonstrated that Al doped ZnO could be a promising adsorbent for effective defluoridation for water.
    Matched MeSH terms: Zinc Oxide*
  9. Naseem T, Bibi F, Arif S, Waseem M, Haq S, Azra MN, et al.
    Molecules, 2022 Oct 22;27(21).
    PMID: 36363976 DOI: 10.3390/molecules27217152
    In this work, graphene oxide (GO) and its reduced graphene oxide-zinc oxide nanocomposite (rGO-ZnO) was used for the removal of Cr (VI) from aqueous medium. By employing a variety of characterization techniques, morphological and structural properties of the adsorbents were determined. The adsorption study was done by varying concentration, temperature, pH, time, and amount of adsorbent. The results obtained confirmed that rGO-ZnO is a more economical and promising adsorbent for removing Cr (VI) as compared to GO. Kinetic study was also performed, which suggested that sorption of Cr (VI) follows the pseudo-first-order model. For equilibrium study, non-linear Langmuir was found a better fitted model than its linearized form. The maximum adsorption capacity calculated for GO and rGO-ZnO nanocomposite were 19.49 mg/g and 25.45 mg/g, respectively. Endothermic and spontaneous nature of adsorption was detected with positive values of ΔS (change in entropy), which reflects the structural changes happening at the liquid/solid interface.
    Matched MeSH terms: Zinc Oxide*
  10. Rajendran S, Hoang TKA, Trudeau ML, Jalil AA, Naushad M, Awual MR
    Environ Pollut, 2022 Jan 01;292(Pt B):118375.
    PMID: 34656681 DOI: 10.1016/j.envpol.2021.118375
    Recently, hetero junction materials (p-n-p and n-p-n) have been developed for uplifting the visible light activity to destroy the harmful pollutants in wastewater. This manuscript presents a vivid description of novel n-p-n junction materials namely CeO2-PPy-ZnO. This novel n-p-n junction was applied as the photocatalyst in drifting the mobility of charge carriers and hence obtaining the better photocatalytic activity when compared with p-n and pure system. Such catalyst's syntheses were successful via the copolymerization method. The structural, morphological and optical characterization techniques were applied to identify the physio-chemical properties of the prepared materials. Additionally, the superior performance of this n-p-n nanostructured material was demonstrated in the destruction of micro organic (chlorophenol) toxic wastes under visible light. The accomplished ability of the prepared catalysts (up to 92% degradation of chlorophenol after 180 min of irradiation) and their profound degradation mechanism was explained in detail.
    Matched MeSH terms: Zinc Oxide*
  11. Lam SM, Sin JC, Zeng H, Lin H, Li H, Mohamed AR, et al.
    Chemosphere, 2022 Jan;287(Pt 4):132384.
    PMID: 34597645 DOI: 10.1016/j.chemosphere.2021.132384
    BiFeO3 nanoparticle decorated on flower-like ZnO (BiFeO3/ZnO) was fabricated through a facile hydrothermal-reflux combined method. This material was utilized as a composite photocathode for the first time in microbial fuel cell (MFC) to reduce the copper ion (Cu2+) and power generation concomitantly. The resultant BiFeO3/ZnO-based MFC displayed distinct photoelectrocatalytic activities when different weight percentages (wt%) BiFeO3 were used. The 3 wt% BiFeO3/ZnO MFC achieved the maximum power density of 1.301 W m-2 in the catholyte contained 200 mg L-1 of Cu2+ and the power density was greatly higher than those pure ZnO and pure BiFeO3 photocathodes. Meanwhile, the MFC exhibited 90.7% removal of Cu2+ within 6 h under sunlight exposure at catholyte pH 4. The addition of BiFeO3 nanoparticles not only manifested outstanding capability in harvesting visible light, but also facilitated the formation of Z-scheme BiFeO3/ZnO heterojunction structure to induce the charge carrier transfer along with enhanced redox abilities for the cathodic reduction. The pronounced electrical output and Cu2+ reduction efficiencies can be realized through the synergistic cooperation between the bioanode and BiFeO3/ZnO photocathode in the MFC. Furthermore, the developed BiFeO3/ZnO composite presented a good stability and reusability of photoelectrocatalytic activity up to five cyclic runs.
    Matched MeSH terms: Zinc Oxide*
  12. Abdullah FH, Bakar NHHA, Bakar MA
    J Hazard Mater, 2022 Feb 15;424(Pt B):127416.
    PMID: 34655867 DOI: 10.1016/j.jhazmat.2021.127416
    Industrial wastewaters contain hazardous contaminants that pollute the environment and cause socioeconomic problems, thus demanding the employment of effective remediation procedures such as photocatalysis. Zinc oxide (ZnO) nanomaterials have emerged to be a promising photocatalyst for the removal of pollutants in wastewater owing to their excellent and attractive characteristics. The dynamic tunable features of ZnO allow a wide range of functionalization for enhanced photocatalytic efficiency. The current review summarizes the recent advances in the fabrication, modification, and industrial application of ZnO photocatalyst based on the analysis of the latest studies, including the following aspects: (1) overview on the properties, structures, and features of ZnO, (2) employment of dopants, heterojunction, and immobilization techniques for improved photodegradation performance, (3) applicability of suspended and immobilized photocatalytic systems, (4) application of ZnO hybrids for the removal of various types of hazardous pollutants from different wastewater sources in industries, and (5) potential of bio-inspired ZnO hybrid nanomaterials for photocatalytic applications using renewable and biodegradable resources for greener photocatalytic technologies. In addition, the knowledge gap in this field of work is also highlighted.
    Matched MeSH terms: Zinc Oxide*
  13. Zulkefli NN, Noor Azam AMI, Masdar MS, Baharuddin NA, Wan Isahak WNR, Mohd Sofian N
    Molecules, 2022 Dec 17;27(24).
    PMID: 36558155 DOI: 10.3390/molecules27249024
    This study reports on the synthesis of bi-metal compound (BMC) adsorbents based on commercial coconut activated carbon (CAC), surface-modified with metal acetate (ZnAc2), metal oxide (ZnO), and the basic compounds potassium hydroxide (KOH) and sodium hydroxide (NaOH). The adsorbents were then characterized by scanning electron microscopy and elemental analysis, microporosity analysis through Brunauer-Emmett-Teller (BET) analysis, and thermal stability via thermogravimetric analysis. Adsorption-desorption test was conducted to determine the adsorption capacity of H2S via 1 L adsorber and 1000 ppm H2S balanced 49.95% for N2 and CO2. Characterization results revealed that the impregnated solution homogeneously covered the adsorbent surface, morphology, and properties. The adsorption test result reveals that the ZnAc2/ZnO/CAC_B had a higher H2S breakthrough adsorption capacity and performed at larger than 90% capability compared with a single modified adsorbent (ZnAc2/CAC). Therefore, the synthesized BMC adsorbents have a high H2S loading, and the abundance and low cost of CAC may lead to favorable adsorbents in H2S captured.
    Matched MeSH terms: Zinc Oxide*
  14. Idris NJ, Bakar SA, Mohamed A, Muqoyyanah M, Othman MHD, Mamat MH, et al.
    Environ Sci Pollut Res Int, 2021 Feb;28(6):6966-6979.
    PMID: 33025441 DOI: 10.1007/s11356-020-10904-y
    In this work, sand/zinc oxide (ZnO)/titanium dioxide (TiO2)-based photocatalysts were hybridized with graphene oxide (GO) and GO_multi-walled carbon nanotubes (MWCNTs) hybrid solution. The novel hybrid was then used in photocatalysis to degrade dye contamination. The nanocomposite photocatalyst was initially fabricated by growing ZnO nanorods (NRs) via sol-gel immersion followed by synthesizing TiO2 NRs for different times (5 and 20 h) using a hydrothermal method on sand as a substrate. Prior to the hybridization, the initial GO was synthesized using electrochemical exfoliation and further mixed with 1 wt% MWCNTs to form GO_MWCNTs hybrid solution. The synthesized GO and GO_MWCNTs hybrid solution were then incorporated onto sand/ZnO/TiO2 nanocomposite-based photocatalysts through immersion. Various sand/ZnO/TiO2-based photocatalysts were then tested for methylene blue (MB) dye degradation within 3 days. On the basis of UV-Vis measurement, the highest MB degradation was achieved by using sand/ZnO NRs/TiO2 NRs (5 h)/GO_MWCNTs (92.60%). The high surface area and high electrical conductivity of GO_MWCNTs prolonged the lifetime of electron/hole separation and thus enhanced the photocatalytic performance.
    Matched MeSH terms: Zinc Oxide*
  15. Hussein MZ, Azmin WH, Mustafa M, Yahaya AH
    J Inorg Biochem, 2009 Aug;103(8):1145-50.
    PMID: 19577306 DOI: 10.1016/j.jinorgbio.2009.05.016
    Currently the development of green chemistry approach with the use of biomaterial-based activities of microbial cells in the synthesis of various nanostructures has attracted a great attention. In this study, we report on the use of bacterium, Bacillus cereus as a biotemplating agent for the formation of zinc oxide nanoparticles with raspberry- and plate-like structures through a simple thermal decomposition of zinc acetate by maintaining the original pH of the reaction mixtures. Possible mechanism on the formation of the nanostructures is proposed based on the surface chemistry and biochemistry processes involved organic-inorganic interactions between zinc oxide and the microbial cells.
    Matched MeSH terms: Zinc Oxide/metabolism*; Zinc Oxide/chemistry
  16. Tripathy A, Pramanik S, Cho J, Santhosh J, Osman NA
    Sensors (Basel), 2014;14(9):16343-422.
    PMID: 25256110 DOI: 10.3390/s140916343
    The humidity sensing characteristics of different sensing materials are important properties in order to monitor different products or events in a wide range of industrial sectors, research and development laboratories as well as daily life. The primary aim of this study is to compare the sensing characteristics, including impedance or resistance, capacitance, hysteresis, recovery and response times, and stability with respect to relative humidity, frequency, and temperature, of different materials. Various materials, including ceramics, semiconductors, and polymers, used for sensing relative humidity have been reviewed. Correlations of the different electrical characteristics of different doped sensor materials as the most unique feature of a material have been noted. The electrical properties of different sensor materials are found to change significantly with the morphological changes, doping concentration of different materials and film thickness of the substrate. Various applications and scopes are pointed out in the review article. We extensively reviewed almost all main kinds of relative humidity sensors and how their electrical characteristics vary with different doping concentrations, film thickness and basic sensing materials. Based on statistical tests, the zinc oxide-based sensing material is best for humidity sensor design since it shows extremely low hysteresis loss, minimum response and recovery times and excellent stability.
    Matched MeSH terms: Zinc Oxide/chemistry*
  17. Saw KG, Tneh SS, Yam FK, Ng SS, Hassan Z
    PLoS One, 2014;9(2):e89348.
    PMID: 24586707 DOI: 10.1371/journal.pone.0089348
    The concentration of acceptor carriers, depletion width, magnitude of donor level movement as well as the sensitivity factor are determined from the UV response of a heterojunction consisting of ZnO on type IIb diamond. From the comparison of the I-V measurements in dark condition and under UV illumination we show that the acceptor concentration (∼10(17) cm(-3)) can be estimated from p-n junction properties. The depletion width of the heterojunction is calculated and is shown to extend farther into the ZnO region in dark condition. Under UV illumination, the depletion width shrinks but penetrates both materials equally. The ultraviolet illumination causes the donor level to move closer to the conduction band by about 50 meV suggesting that band bending is reduced to allow more electrons to flow from the intrinsically n-type ZnO. The sensitivity factor of the device calculated from the change of threshold voltages, the ratio of dark and photocurrents and identity factor is consistent with experimental data.
    Matched MeSH terms: Zinc Oxide/chemistry*
  18. Saw KG, Aznan NM, Yam FK, Ng SS, Pung SY
    PLoS One, 2015;10(10):e0141180.
    PMID: 26517364 DOI: 10.1371/journal.pone.0141180
    The Burstein-Moss shift and band gap narrowing of sputtered indium-doped zinc oxide (IZO) thin films are investigated as a function of carrier concentrations. The optical band gap shifts below the carrier concentration of 5.61 × 1019 cm-3 are well-described by the Burstein-Moss model. For carrier concentrations higher than 8.71 × 1019 cm-3 the shift decreases, indicating that band gap narrowing mechanisms are increasingly significant and are competing with the Burstein-Moss effect. The incorporation of In causes the resistivity to decrease three orders of magnitude. As the mean-free path of carriers is less than the crystallite size, the resistivity is probably affected by ionized impurities as well as defect scattering mechanisms, but not grain boundary scattering. The c lattice constant as well as film stress is observed to increase in stages with increasing carrier concentration. The asymmetric XPS Zn 2p3/2 peak in the film with the highest carrier concentration of 7.02 × 1020 cm-3 suggests the presence of stacking defects in the ZnO lattice. The Raman peak at 274 cm-1 is attributed to lattice defects introduced by In dopants.
    Matched MeSH terms: Zinc Oxide/chemistry*
  19. Haarindraprasad R, Hashim U, Gopinath SC, Kashif M, Veeradasan P, Balakrishnan SR, et al.
    PLoS One, 2015;10(7):e0132755.
    PMID: 26167853 DOI: 10.1371/journal.pone.0132755
    The performance of sensing surfaces highly relies on nanostructures to enhance their sensitivity and specificity. Herein, nanostructured zinc oxide (ZnO) thin films of various thicknesses were coated on glass and p-type silicon substrates using a sol-gel spin-coating technique. The deposited films were characterized for morphological, structural, and optoelectronic properties by high-resolution measurements. X-ray diffraction analyses revealed that the deposited films have a c-axis orientation and display peaks that refer to ZnO, which exhibits a hexagonal structure with a preferable plane orientation (002). The thicknesses of ZnO thin films prepared using 1, 3, 5, and 7 cycles were measured to be 40, 60, 100, and 200 nm, respectively. The increment in grain size of the thin film from 21 to 52 nm was noticed, when its thickness was increased from 40 to 200 nm, whereas the band gap value decreased from 3.282 to 3.268 eV. Band gap value of ZnO thin film with thickness of 200 nm at pH ranging from 2 to 10 reduces from 3.263eV to 3.200 eV. Furthermore, to evaluate the transducing capacity of the ZnO nanostructure, the refractive index, optoelectric constant, and bulk modulus were analyzed and correlated. The highest thickness (200 nm) of ZnO film, embedded with an interdigitated electrode that behaves as a pH-sensing electrode, could sense pH variations in the range of 2-10. It showed a highly sensitive response of 444 μAmM-1cm-2 with a linear regression of R2 =0.9304. The measured sensitivity of the developed device for pH per unit is 3.72μA/pH.
    Matched MeSH terms: Zinc Oxide/chemistry*
  20. Adil M, Lee K, Mohd Zaid H, A Shukur MF, Manaka T
    PLoS One, 2020;15(12):e0244738.
    PMID: 33382855 DOI: 10.1371/journal.pone.0244738
    Utilization of metal-oxide nanoparticles (NPs) in enhanced oil recovery (EOR) has generated substantial recent research interest in this area. Among these NPs, zinc oxide nanoparticles (ZnO-NPs) have demonstrated promising results in improving oil recovery due to their prominent thermal properties. These nanoparticles can also be polarized by electromagnetic (EM) field, which offers a unique Nano-EOR approach called EM-assisted Nano-EOR. However, the impact of NPs concentrations on oil recovery mechanism under EM field has not been well established. For this purpose, ZnO nanofluids (ZnO-NFs) of two different particle sizes (55.7 and 117.1 nm) were formed by dispersing NPs between 0.01 wt.% to 0.1 wt.% in a basefluid of sodium dodecylbenzenesulfonate (SDBS) and NaCl to study their effect on oil recovery mechanism under the electromagnetic field. This mechanism involved parameters, including mobility ratio, interfacial tension (IFT) and wettability. The displacement tests were conducted in water-wet sandpacks at 95˚C, by employing crude oil from Tapis. Three tertiary recovery scenarios have been performed, including (i) SDBS surfactant flooding as a reference, (ii) ZnO-NFs flooding, and (iii) EM-assisted ZnO-NFs flooding. Compare with incremental oil recovery from surfactant flooding (2.1% original oil in place/OOIP), nanofluid flooding reaches up to 10.2% of OOIP at optimal 0.1 wt.% ZnO (55.7 nm). Meanwhile, EM-assisted nanofluid flooding at 0.1 wt.% ZnO provides a maximum oil recovery of 10.39% and 13.08% of OOIP under EM frequency of 18.8 and 167 MHz, respectively. By assessing the IFT/contact angle and mobility ratio, the optimal NPs concentration to achieve a favorable ER effect and interfacial disturbance is determined, correlated to smaller hydrodynamic-sized nanoparticles that cause strong electrostatic repulsion between particles.
    Matched MeSH terms: Zinc Oxide*
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links