Biodiesel from palm oil mill sludge (POMS) was prepared in the presence of novel silica-based heterogeneous catalysts derived from Imperata cylindrica sp. Imperatacid and Imperatabase are two types of heterogeneous catalysts derived from Imperata cylindrica sp and characterized using scanning electron microscopy, Energy Dispersive X-ray, Brunauer-Emmett-Teller surface area and pore size measurement. Imperatacid has particle size of 43.1-83.9 µm while Imperatabase in the range of 89-193 µm. Imperatacid was conveniently applied in esterification step to afford > 90 wt% oil in 1:3 (oil/methanol) and 10 wt% catalyst, followed by transesterification with 1 wt% Imperatabase and 1:1 (oil/methanol) for 1 h at 65°C to afford 80% biodiesel with higher percentage of methyl palmitate (48.97%) and methyl oleate (34.14%) compare to conventional homogeneous catalyst. Reusability of the catalyst up to three times afforded biodiesel ranging from 78-80% w/w. The biodiesel was demonstrated onto alternative diesel engine (Megatech(®)-Mark III) and showed proportional increased of torque (ɽ) to biodiesel loading.
An optimal ratio of omega-6 to omega-3 (ω-6/ω-3) polyunsaturated fatty acids (PUFA) in the diet prevents the pathogenesis of many inflammatory diseases. This study aimed to synthesize and characterize ternary oil blends with optimal ω-6/ω-3 ratios using olive (OL), sunflower (SU), and cress (CR) oils. The oxidative stability, thermal profile, fatty acid (FA) and tocopherol compositions, and the physicochemical properties of the blends were used to determine their quality. Oil mixtures were prepared with 2, 3, 4, and 5 ω-6/ω-3 ratios. FA composition and tocopherol content were the most important factors affecting the oxidation and thermal stabilities of the oils. All oil mixtures showed good quality indices. Thus, synthetized oil blends with high oxidative stability, high antioxidant content, optimal ω-6/ω-3 ratios, and recommended FA compositions can influence human health. The composition of healthy oil blends with optimal ω-6/ω-3 ratios was expressed mathematically and depicted graphically in a ternary diagram.
Allium ampeloprasum L., commonly known as wild leek, is an edible vegetable that has been cultivated for centuries. However, no detailed studies have been undertaken to valorize A. ampeloprasum seed oil. This study aims to evaluate the physicochemical properties, chemical composition, and antioxidant activity of A. ampeloprasum seed oil. The seed oil content was found to be 18.20%. Gas chromatographymass spectrometry (GC-MS) showed that linoleic acid (71.65%) was the dominant acid, followed by oleic acid (14.11%) and palmitic acid (7.11%). A. ampeloprasum seed oil exhibited an oxidative stability of 5.22 h. Moreover, γ- and δ-tocotrienols were the major tocols present (79.56 and 52.08 mg/100 g oil, respectively). The total flavonoid content (16.64 µg CE /g oil) and total phenolic content (62.96 µg GAE /g oil) of the seed oil were also determined. The antioxidant capacity of the oil, as evaluated using the ABTS assay (136.30 µM TEAC/g oil), was found to be significant. These findings indicate that A. ampeloprasum seeds can be regarded as a new source of edible oil having health benefits and nutritional properties.
The present study is focused on the effect of the TTABr/MX/H2O-nanoparticles on the rate of piperidinolysis of ionized phenyl salicylate where TTABr represents tetradecyltrimethylammonium bromide and MX = NaCl, NaBr and CnH2n+1CO2Na with n = 4, 5, 6 and 7. Pseudo-first-order rate constant for the piperidinolysis of ionized phenyl salicylate at 35°C and constant concentration [PSa(-)]T = 0.2 mM, [Pip]T = 0.1 M, [NaOH] = 30 mM, [TTABr]T and different [MX] follow an empirical relationship which gives two empirical constant, (X)kcat and K(X/S). The value of relative counterion (X) binding constant, RX(Br) were calculated from the relationship; RX(Br) = (X)kcat/(Br)kcat. The values of RX(Br) for X = C4H9CO2(-), C5H11CO2(-), C6H13CO2(-), and C7H15CO2(-) are increasing with increase in the number of alkyl chain of counterion X.
Palm and soya oils were converted to monoglycerides via transesterification of triglycerides with glycerol by one step process to produce renewable polyols. Thermoplastic polyurethanes (TPPUs) were prepared from the reaction of the monoglycerides which act as polyol with 4,4'-methylenediphenyldiisocyanate (MDI) whereas, thermosetting polyurethanes (TSPUs) were prepared from the reaction of glycerol, MDI and monoglycerides in one pot. Characterization of the polyurethanes was carried out by FT-IR, (1)H NMR, and iodine value and sol-gel fraction. The TSPUs showed good thermal properties compared to TPPUs as well as TSPUs exhibits good properties in pencil hardness and adhesion, however poorer in flexural and impact strength compared to TPPUs. The higher percentage of cross linked fraction, the higher degree of cross linking occurred, which is due to the higher number of double bond presents in the TSPUs. These were reflected in iodine value test as the highest iodine value of the soya-based thermosetting polyurethanes confirmed the highest degree of cross linking. Polyurethanes based on soya oil showed better properties compared to palm oil. This study is a breakthrough development of polyurethane resins using palm and soya oils as one of the raw materials.
New polyurethane (PU) nanocomposites were prepared from a dispersion of 0 - 5% montmorillonite (MMT) clay with isocyanate and soya oil polyol that was synthesized via transesterification of triglycerides to reduce petroleum dependence. FT-IR spectra indicate the presence of hydrogen bonding between nanoclay and the polymer matrix, whereas the exfoliated structure of clay layers was confirmed by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Optical microscopy, mechanical and thermal analyses were done to investigate significant improvement of the nanocomposites. The results showed PU-3% nanoclay (NC) showed optimum results in mechanical properties such as tensile and flexural strength but the lowest in impact strength.
Fatty hydrazides (FH) have been successfully synthesized from palm oils by a one-step lipase catalyzed reaction. The synthesis was carried out by treating the oils with hydrazine hydrate at neutral pH using an immobilized lipase, Lipozyme as the catalyst. The percentages of conversion of RBD (refined, bleached and deodorized) palm oil (PO), RBD palm olein (POn), RBD palm stearin (PS) and RBD palm kernel olein (PKOn) into their fatty hydrazides are 95, 97, 97 and 99, respectively.
A study was conducted to detect and quantify lard stearin (LS) content in canola oil (CaO) using differential scanning calorimetry (DSC). Authentic samples of CaO were obtained from a reliable supplier and the adulterant LS were obtained through a fractional crystallization procedure as reported previously. Pure CaO samples spiked with LS in levels ranging from 5 to 15% (w/w) were analyzed using DSC to obtain their cooling and heating profiles. The results showed that samples contaminated with LS at 5% (w/w) level can be detected using characteristic contaminant peaks appearing in the higher temperature regions (0 to 70°C) of the cooling and heating curves. Pearson correlation analysis of LS content against individual DSC parameters of the adulterant peak namely peak temperature, peak area, peak onset temperature indicated that there were strong correlations between these with the LS content of the CaO admixtures. When these three parameters were engaged as variables in the execution of the stepwise regression procedure, predictive models for determination of LS content in CaO were obtained. The predictive models obtained with single DSC parameter had relatively lower coefficient of determination (R(2) value) and higher standard error than the models obtained using two DSC parameters in combination. This study concluded that the predictive models obtained with peak area and peak onset temperature of the adulteration peak would be more accurate for prediction of LS content in CaO based on the highest coefficient of determination (R(2) value) and smallest standard error.
This study was to characterize the seed fat from Madhuca longifolia known as Mee fat and its solid and liquid fractions with the objective of distinguishing them. A sample of Mee fat was partitioned into solid and liquid fractions using acetone as the solvent medium. The isolated fractions were compared to the native Mee fat sample with respect to various physico-chemical parameters using standard chemical methods as well as instrumental techniques such as, gas liquid chromatography (GLC), reversed-phase high performance liquid chromatography (RP-HPLC), and differential scanning calorimetry (DSC). Basic analyses indicated that there were wide variations between the native sample and its fractions with respect to iodine value (IV), and slip melting point (SMP). The cloud point (CP) of the liquid fraction was found to be 10.5 degrees C. Fatty acid compositional analyses showed that the proportion of saturated fatty acids (SFA) such as palmitic and stearic went up in the high-melting fraction (HMF) while in low-melting fraction (LMF) the proportion of unsaturated fatty acid (USFA) such as oleic and lenoleic increased. According to the HPLC analyses, Mee fat had a tiacyl glycerol (TAG) sequence similar to that of palm oil. After fractionation, the solid and liquid fractions obtained were found to have TAG profiles very much different from the native sample. Thermal analyses by DSC showed that Mee fat had two-widely separated high and low melting thermal transitions, a feature which was beneficial for the effective separation of solid and liquid fractions. The thermal profiles displayed by the fractions were clearly distinguishable from that of the native sample.
The seeds (6.9±0.2% by weight of fruit) of the red-skin rambutan (Nephelium lappaceum L.) contain a considerable amount of crude fat (38.0±4.36%) and thus, the aim of the study was to determine the physico-chemical properties of this fat for potential applications. The iodine and saponification values, and unsaponifiable matter and free fatty acid contents of the seed fat were 50.27 g I2/100g fat, 182.1 mg KOH/g fat, 0.8% and 2.1%, respectively. The fat is pale yellow with a Lovibond color index of 3.1Y+1.1R. The fatty acid profile indicates an almost equal proportion of saturated (49.1%) and unsaturated (50.9%) fatty acids, where oleic (42.0%) and arachidic (34.3%) acids were the most dominant fatty acids. It also contained small amounts of stearic (8.0%), palmitic (4.6%), gadoleic (5.9%), linoleic (2.2%), behenic (2.1%) palmitoleic (0.7%) myristic (0.1%) and erucic (0.1%) acids. HPLC analysis showed that the fat comprised mainly unknown triacylglycerols (TAG) with high retention times indicating they have higher carbon numbers compared with many vegetable oils. The fat has melting and cooling points of 44.2°C and -42.5°C, respectively, making it a semi-solid at room temperature. The solid content at 0°C was 53.5% and the fat melted completely at 40°C. z-Nose analysis showed that the presence of high levels of volatile compounds in red-skin rambutan seed and seed fat.
Skincare industries are growing rapidly around the globe but most products are formulated using synthetic chemicals and organic solvent extracted plant extracts, thus may be hazardous to the users and incur higher cost for purification that eventually leads to phytonutrient degradation. Therefore, this study aimed to formulate a stable natural formulation with antioxidant and antimicrobial activities by using supercritical carbon dioxide (SC-CO 2 ) extracted palm-pressed fiber oil (PPFO) as an active ingredient with virgin coconut oil (VCO) as a formulation base. PPFO was extracted from fresh palm-pressed fiber (PPF) while VCO was from dried grated coconut copra using SC-CO 2 before being subjected to the analyses of physicochemical properties, phytonutrient content and biological activities including antioxidant and antimicrobial. The nanoemulgel formulations were then developed and examined for their stability through accelerated stability study for 3 months by measuring their pH, particle size, polydispersity index and zeta potential. The results showed that PPFO contained a high amount of phytonutrients, especially total carotenoid (1497 ppm) and total tocopherol and tocotrienol (2269 ppm) contents. The newly developed nanoemulgels maintained their particles in nano size and showed good stability with high negative zeta potentials. Sample nanoemulgel formulated with 3% PPFO diluted in VCO as effective concentration showed significantly stronger antioxidant activity than the control which was formulated from 3% tocopheryl acetate diluted in mineral oil, towards DPPH and ABTS radicals, with IC 50 values of 67.41 and 44.28 µL/mL, respectively. For the antibacterial activities, the sample nanoemulgel was found to inhibit Gram positive bacteria S. aureus and S. epidermidis growth but not the Gram negative strain E. coli. Overall, this study revealed the potential of SF-extracted PPFO as an active ingredient in the antioxidant topical formulations thus future study on in vitro skin cell models is highly recommended for validation.
Liquid detergent has an increasing demand in North America, Western Europe, and Southeast Asia countries owing to its convenience to use and efficiency to clean. Alpha methyl ester sulfonates (α-MES), an anionic surfactant derived from palm oil based methyl ester, was reported to have lower manufacturing cost, good detergency with less dosage, excellent biodegradability, higher tolerance to hard water, and lower eco-toxicity as compared to linear alkylbenzene sulfonates (LABS). LABS was known as the workhorse of the detergent industry in the 20th century. Although palm-based α-MES was successfully used as the sole surfactant in powder detergent, there are still some unsettled technical issues related to phase stability and viscosity when using this anionic surfactant in heavy-duty laundry liquid detergent formulations. This paper will review not only the market overview of detergents, the application and performance of green surfactants in laundry detergents but also will highlight the technical issues related to the application of palm-based α-MES in laundry liquid detergent and some of the possible methods to overcome the formulation adversities.
Para rubber seed was macerated in petroleum ether and n-hexane, individually, for 30 min. The extraction was additionally performed by reflux and soxhlet for 6 h with the same solvent and proportion. Soxhlet extraction by petroleum ether afforded the greatest extractive yield (22.90 ± 0.92%). Although antioxidant activity by means of 1, 1-diphenyl-2-picrylhydrazyl (DPPH) assay was insignificantly differed in soxhleted (8.90 ± 1.15%) and refluxed (9.02 ± 0.71%) by n-hexane, soxhlet extraction by n-hexane was significantly (p < 0.05) potent scavenged 2,2'-azino-bis(3-ethylbenzothaiazoline)-6-sulfonic acid) or ABTS radical with trolox equivalent antioxidant capacity (TEAC) of 66.54 ± 6.88 mg/100 g oil. This extract was non cytotoxic towards normal human fibroblast cells. In addition, oleic acid and palmitic acid were determined at a greater content than in the seed of para rubber cultivated in Malaysia, although linoleic and stearic acid contents were not differed. This bright yellow extract was further evaluated on other physicochemical characters. The determined specific gravity, refractive index, iodine value, peroxide value and saponification value were in the range of commercialized vegetable oils used as cosmetic raw material. Therefore, Para rubber seed oil is highlighted as the promising ecological ingredient appraisal for cosmetics. Transforming of the seed that is by-product of the important industrial crop of Thailand into cosmetics is encouraged accordingly.
In the current research work, effect of microwave irradiation energy on the esterification of palm fatty acid distillate (PFAD) to produce PFAD methyl ester / biodiesel was intensively appraised. The PFAD is a by-product from refinery of crude palm oil consisting >85% of free fatty acid (FFA). The esterification reaction process with acid catalyst is needed to convert the FFA into fatty acid methyl ester or known as biodiesel. In this work, fabricated microwave-pulse width modulation (MPWM) reactor with controlled temperature was designed to be capable to increase the PFAD biodiesel production rate. The classical optimization technique was used in order to study the relationship and the optimum condition of variables involved. Consequently, by using MPWM reactor, mixture of methanol-to-PFAD molar ratio of 9:1, 1 wt.% of sulfuric acid catalyst, at 55°C reaction temperature within 15 min reaction time gave 99.5% of FFA conversion. The quality assessment and properties of the product were analyzed according to the American Society for Testing and Materials (ASTM), European (EN) standard methods and all results were in agreement with the standard requirements. It revealed that the use of fabricated MPWM with controlled temperature was significantly affecting the rate of esterification reaction and also increased the production yield of PFAD methyl ester.
Sixty-four bottles of red palm olein and palm olein (constituted as control) samples were stored at permutations of common home setting variables which are: temperature (room temperature (24°C) or 8°C), light (kept in dark or exposure under light) and oxygen (opened or sealed caps). The effects of temperature, oxygen and light on the stability of red palm olein and palm olein were studied over 4 months of storage at simulated domestic conditions. The degree of auto- and photo-oxidations was evaluated by monitoring the following quality parameters: acidity, peroxide and p-anisidine values, fatty acids composition, carotenes and vitamin E. It is noted from the study that opened bottles of red palm olein was found to be stable for 4 months in comparison to its counterpart (palm olein) evidenced from their primary oxidative constituents (peroxides) and hydrolytic behavior (free fatty acids). Opened bottles are better off when stored at 8°C and protected from light for a longer shelf-life. Sealed bottles of palm olein showed better storage stability in the dark at 8°C; whereas sealed bottles of red palm olein was found to be stable at both temperatures studied without the influence of light. After 4 months of varying storage conditions, the fatty acid composition, vitamin E and carotenes of both oils remained unchanged. The phytonutrients in red palm olein rendered better storage stability when compared to palm olein.
Red palm olein is known to be high in carotenes and vitamin E (tocols) and possess various nutritional benefits. This study evaluates the effect of prolonged heating using three common cooking techniques i.e. deep-fat fryer, microwave oven and conventional oven, on the profiles of carotenes and tocols as well as the physico-chemical changes occurring in red palm olein when compared to conventional palm olein. Physico-chemical changes in all oils were gauged based on their peroxide, p-anisidine and total oxidation values, acidity, and fatty acid composition. Both red palm olein and palm olein were thermally stable based on their lower rate of hydrolytic and oxidative degradations as well as higher tocols retention, which allow the oils to undergo heating up to 3 hours using deep-fat fryer and conventional oven. Nevertheless, red palm olein seemed not suitable for prolonged heating processes considering lower retention of carotenes. Microwave heating also influenced the stability of phytonutrients.
The study was designed to evaluate the nutritive value, thermal stability and consumer acceptance of cupcakes baked with red palm olein compared to palm olein. Thermal stability was evaluated for acidity, peroxide, p-anisidine and total oxidation value (cumulative between peroxide and p-anisidine values), as well as fatty acid composition. The concentrations of phytonutrients including tocopherols and tocotrienols, alpha- and beta-carotene after baking were also determined. Acceptance of the cupcakes was assessed using a structured hedonic scale of five points by 29 panelists. As compared to initial test oil (red palm olein), acidity (red palm olein, 0.07±0.01% vs cupcakes containing red palm olein, 0.09±0.01%; P=0.0232), peroxide value (red palm olein, 0.33±0.05 meq O2 kg-1 vs cupcakes containing red palm olein 0.73±0.06 meq O2 kg-1; P=0.0011) and total oxidation value (red palm olein, 2.24±0.13 unit vs cupcakes containing red palm olein, 3.09±0.17 unit; P=0.0012) were found to be higher in cupcakes containing red palm olein, which is within the acceptable rancidity range (peroxide value < 7.5 meq O2 kg-1) for snack food category. No changes were found on oxidative parameters (acidity, peroxide, p-anisidine values and total oxidation value) in cupcakes containing palm olein. Cupcakes made with red palm olein retained nearly 100% of alpha- and beta-carotenes upon baking. Tocopherol homologues were stable in both comparisons, with 95% retention as compared to tocotrienol homologues (~85%). Cupcakes made from red palm olein received higher score (mean=3.29) in sensory evaluation as compared to cupcakes containing palm olein (mean=3.07). The study, therefore, encourages the inclusion of red palm olein in the formulation of bakery products.
Acidolysis to incorporate oleic acid into refined, bleached and deodorized (RBD) palm olein (IV 56) using various lipases (enzymes) as catalysts to increase the oleic content of the oil was investigated. Immobilised lipases (lipase PLG, Lipozyme TL IM, Lipozyme RM IM and Novozym 435) and non-immobilised lipase (lipase PL) were used in this study to compare the effectiveness of the selected lipases in catalyzing the reaction to produce a high oleic oil. The results showed that the TAG of OLO/OOL content was increased at least 4 fold and OOO content was increased at least 3 fold when a 5% enzyme load was used. Lipase PL showed the greatest increase in tri-unsaturated triacylglycerols (TAGs) content. A pilot scale experiment conducted using TL IM enzyme, followed by recovery of the oil and fractionation allows the production of oils with varying oleic contents. A high oleic content of 56% was achievable.
The impact of microwave roasting on the thermooxidative degradation of perah seed oil (PSO) was evaluated during heating at a frying temperature (170°C). The roasting resulted significantly lower increment of the values of oxidative indices such as free acidity, peroxide value, p-anisidine, total oxidation (TOTOX), specific extinctions and thiobarbituric acid in oils during heating. The colour L* (lightness) value dropped gradually as the heating time increased up to 12 h, whereas a*(redness) and b* (yellowness) tended to increase. The viscosity and total polar compound in roasted PSO was lower as compared to that in unroasted one at each heating times. The tocol retention was also high in roasted samples throughout the heating period. The relative contents of polyunsaturated fatty acids (PUFAs) were decreased to 94.42% and saturated fatty acids (SFAs) were increased to 110.20% in unroasted sample, after 12 h of heating. On the other hand, in 3 min roasted samples, the relative contents of PUFAs were decreased to 98.08% and of SFAs were increased to 103.41% after 12 h of heating. Outcome from analyses showed that microwave roasting reduced the oxidative deteriorations of PSO during heating.
Phosphoric acid is used in the refining of palm oil for the removal of phosphatides. The high concentration of phosphorus in solvent extracted palm-pressed mesocarp fiber oil hinders palm oil mills to recover this phytonutrients-rich residual oil in pressed fiber which typically contains 0.1 to 0.2% of total oil yield. This study aimed to refine the palm-pressed mesocarp fiber oil and determine the optimum dosage of phosphoric acid for acid-degumming of palm-pressed mesocarp fiber oil while retaining its phytonutrients. The refining process was carried out with combination of wet degumming, acid degumming, neutralisation, bleaching and deodorization. The optimum dose of phosphoric acid was identified as 0.05 wt.% by incorporating the wet degumming process. The refined palm-pressed mesocarp fiber oil showed a reduction in phosphorus content by 97% (from 901 ppm to 20 ppm) and 97% free fatty acid content removal (from 6.36% to 0.17%), while the Deterioration of Bleachability Index increased from 1.76 to 2.48, which showed an increment of 41%. The refined oil retained the key phytonutrients such as carotenoids (1,150 ppm) and vitamin E (1,540 ppm) that can be further developed into high-value products. The oil meets the quality specification of refined, bleached, and deodorized palm oil while preserving the heat-sensitive phytonutrients, which in turn provides a new resource of nutritious oil.