Pyrolysis oil from oil palm biomass can be a sustainable alternative to fossil fuels and the precursor for synthesizing petrochemical products due to its carbon-neutral properties and low sulfur and nitrogen content. This work investigated the effect of applying mesoporous acidic catalysts, Ni-Mo/TiO2 and Ni/Al2O3, in a catalytic co-pyrolysis of oil palm trunk (OPT) and polypropylene (PP) from 500 to 700 °C. The obtained oil yields varied between 12.67 and 19.50 wt.% and 12.33-17.17 wt.% for Ni-Mo/TiO2 and Ni/Al2O3, respectively. The hydrocarbon content in oil significantly increased up to 54.07-58.18% and 37.28-68.77% after adding Ni-Mo/TiO2 and Ni/Al2O3, respectively. The phenolic compounds content was substantially reduced to 8.46-20.16% for Ni-Mo/TiO2 and 2.93-14.56% for Ni/Al2O3. Minor reduction in oxygenated compounds was noticed from catalytic co-pyrolysis, though the parametric effects of temperature and catalyst type remain unclear. The enhanced deoxygenation and cracking of phenolic and oxygenated compounds and the PP decomposition resulted in increased hydrocarbon production in oil during catalytic co-pyrolysis. Catalyst addition also promoted the isomerization and oligomerization reactions, enhancing the formation of cyclic relative to aliphatic hydrocarbon.
Oil palm trunk (OPT) represents one of the five main oil palm biomass wastes with high carbon content that can be economically converted to a large surface area, porous activated carbon (AC) adsorbent to treat palm oil mill effluent wastewater in Indonesia and Malaysia. In the first portion of this work, the design of the experiment was used to determine the optimum set of synthesis parameters required to maximize the iodine number of AC [i.e., Brunauer-Emmett-Teller (BET) specific surface area indicator] prepared from OPT via chemical activation route using H3PO4. The iodine numbers of AC and AC yield were probed as the impregnation ratio, the activation time, and the activation temperature were varied in the range of 0.28-3.47, 5.68-69.32 min, and 379-521 °C, respectively. An impregnation ratio of 2.29, an activation time of 6 min, and an activation temperature of 450 °C were identified as the optimum set of synthesis parameters. In the second portion of the work, the AC synthesized using the optimum parameters were then characterized and tested as an adsorbent for tannin. N2 sorption results revealed that the AC exhibits type IV isotherm, that is, contains micropores and mesopores and displays a relatively high BET specific surface area of 1657 m2 g-1. Adsorption equilibria isotherms for tannin adsorption onto the AC were collected at three different pH of 2, 4, and 6 and were nonlinearly fitted using Langmuir and Freundlich isotherm models, where the Langmuir isotherm gave better fitting than Freundlich. The higher adsorption capacity at lower pH can be explained in terms of the absence of electrostatic repulsion interaction between the AC surface and the tannic acid species as suggested by the point of zero charges (pHpzc) of 4.8 and an increasing ionization of tannic acid with pH rise between 4 and 7. Adsorption kinetics data were also obtained at four different pH of 2, 4, 6, and 8 where the nonlinear pseudo-first-order model best fitted the kinetic at pH of 2 and the nonlinear pseudo-second-order model represented the kinetic best at the remaining higher pH, which suggests that tannin adsorption onto AC occurred by physisorption at pH of 2 and by chemisorption at pH of 4, 6, and 8.
This work investigates the physicochemical characteristics of grease-trap wastewater discharged from a large community market. It proposes potential mechanisms of fat, oil, and grease (FOG) solid formation, separation, and accumulation inside grease traps. Sixty-four samples, i.e., the floated scum, suspended solid-liquid wastewater, and settled sludge, were collected from the grease-trap inlet and outlet chambers. A lower pH of 5-6 at 25-29 °C inside the grease trap than those reported under the sewer conditions (pH 6-7) was revealed. A significant difference in solid and dissolved constituents was also discovered between the inlet and outlet chambers, indicating that the baffle wall could affect the separation mechanism. The sludge samples had 1.5 times higher total solids (TS) than the scum samples, i.e., 0.225 vs. 0.149 g g-1 TS, revealing that the sludge amount impacted more significantly the grease trap capacity and operation and maintenance. In contrast, the scum samples had 1.4 times higher volatile solids (VS) than the sludge samples, i.e., 0.134 vs. 0.096 g g-1 VS, matching with the 64.2 vs. 29.7% of carbon content from CHN analysis. About 2/3 of the free fatty acids (FFAs) with palmitic acids were the primary saturated FFAs, while the remaining 1/3 of unsaturated FFAs were found in the solid and liquid samples. Although up to 0.511 g g-1 FOG can be extracted from the scum samples, none from the sludge samples. More diverse minerals/metals other than Na, Cl, and Ca were found in the sludge samples than in the scum samples. Grease-trap FOG solids and open drain samples exhibited similar physicochemical properties to those reported in the literature. Four potential mechanisms (crystallization, emulsification, saponification, and baffling) were presented. This work offers insights into the physicochemical properties of grease-trap wastewater that can help explore its FOG solid formation, separation, and accumulation mechanisms inside a grease trap.