A rare combination of a segmental ulnar fracture with fracture dislocation of the head of the radius and intraarticular fracture of the distal radius concomitant with an ipsilateral scaphoid, lunate and coronoid process fractures is presented. The mechanism of injury could possibly be a tremendous impact on the outstretched hand with a dorsiflexed wrist, fracturing the carpal bones and the distal radius. Transmitted axial forces on the ulna in a pronating forearm resulted in the other fractures. To the best of our knowledge, no such case has been reported. Open reduction with screw fixation of the scaphoid, plating of the proximal ulna and Kirschner wiring of the distal radius and radial head dislocation were done.
The relationship between microarchitecture to the failure mechanism and mechanical properties can be assessed through experimental and computational methods. In this study, both methods were utilised using bovine cadavers. Twenty four samples of cancellous bone were extracted from fresh bovine and the samples were cleaned from excessive marrow. Uniaxial compression testing was performed with displacement control. After mechanical testing, each specimen was ashed in a furnace. Four of the samples were exemplarily scanned using micro-computed tomography (μCT) and three dimensional models of the cancellous bones were reconstructed for finite element simulation. The mechanical properties and the failure modes obtained from numerical simulations were then compared to the experiments. Correlations between microarchitectural parameters to the mechanical properties and failure modes were then made. The Young's modulus correlates well with the bone volume fraction with R² = 0.615 and P value 0.013. Three different types of failure modes of cancellous bone were observed: oblique fracture (21.7%), perpendicular global fracture (47.8%), and scattered localised fracture (30.4%). However, no correlations were found between the failure modes to the morphological parameters. The percentage of error between computer predictions and the actual experimental test was from 6 to 12%. These mechanical properties and information on failure modes can be used for the development of synthetic cancellous bone.
The use of bicortical screws to fix metacarpal fractures has been suggested to provide no added biomechanical advantage over unicortical screw fixation. However, this was only demonstrated in static loading regimes, which may not be representative of biological conditions. The present study was done to determine whether similar outcomes are obtained when cyclic loading is applied. Transverse midshaft osteotomies were created in 20 metacarpals harvested from three cadavers. Fractures were stabilised using 2.0 mm mini fragment plates fixed with either bicortical or unicortical screw fixation. These fixations were tested to failure with a three-point bending cyclic loading protocol using an electromechanical microtester and a 1 kN load cell. The mean load to failure was 370 N (SD 116) for unicortical fixation and 450 N (SD 135) for bicortical fixation. Significant differences between these two constructs were observed. A biomechanical advantage was found when using bicortical screws in metacarpal fracture plating.
Osteoarthritis and falls are common conditions affecting older individuals which are associated with disability and escalating health expenditure. It has been widely assumed that osteoarthritis is an established risk factor for falls in older people. The relationship between osteoarthritis and falls has, quite surprisingly, not been adequately elucidated, and published reports have been conflicting. Our review of the existing literature has found limited evidence supporting the current assumption that the presence of osteoarthritis is associated with increased risk of falls with suggestions that osteoarthritis may actually be protective against falls related fractures. In addition, joint arthroplasty appears to increase the risk of falls in individuals with osteoarthritis.
Adequate pain relief is a requisite for a successful closed manipulative reduction (CMR) of fractures and dislocations. This prospective study was undertaken to assess the mode and adequacy of pain relief given to patients undergoing such procedures at Seremban Hospital from the 1st April to the 31st May 2001. All patients with fractures and dislocations scheduled to undergo CMR were included in this study. The type of sedative agents and analgesia administered were recorded. Demographic data and the type of fracture or dislocation of the selected patients were documented. A visual analogue scale (VAS) for pain perception was given to both to the patients and the medical personnel who performed the procedure. All data were collected manually before entered into computerized database for analysis. Of 72 patients included in this study, 47% were Malay, 26% Indian, 21% Chinese and 6% others. There was male predominance and the patients' age ranged between 9 to 79 years (average 27.4 years). Upper limb injuries (79%) were mainly fractures of the radius and ulna (29%) and isolated fracture radius (21%). For the lower limb injuries (21%), combined tibia and fibula fractures constituted 10% of the total cases followed by isolated tibia fractures (10%) and hip dislocation (1%). The most common pain relieving agents given during the CMR were intravenous pethidine alone (43%) followed by combination of intravenous pethidine and valium (36%), intramuscular pethidine (17%) and intramuscular tramal (4%). The Visual Analogue Score (VAS) for pain perception revealed that 61% of the patients had moderate pain while 21% had severe pain during the course of the procedures. Suboptimal pain relief administered during CMR should prompt positive actions to ensure that the patient is not subjected to undue pain just for the sake of an acceptable fracture reduction.