It is known that restoration of erased engraved identification marks on the engine and the chassis of a car or on a firearm has low success rate. Unlike stamping, engraving on a metal surface leaves no pronounced, permanent subsurface deformation in the crystalline structure, also called dislocation that can be revealed by suitable methods. Hence, the current research work investigated whether metallographic reagents used in the restoration of stamp (compression) marks could be applied to recover engraved marks on steel surfaces and also to establish the sensitivity and effectiveness of some of these reagents for the restoration of the marks. Experiments were conducted by mechanically engraving alphanumeric characters on several steel plates using a computer controlled engraving machine called Gravograph. The markings were later erased from the above steel plates by removing the metal in stages of 0.01 mm through 0.04 mm below the bottom of the engraving. Several plates were thus prepared wherein each one had been abraded to a specific depth. Then eight metallographic reagents were tested on each one of the above erased plates using a swabbing technique. The results had shown that while most of the reagents were able to restore marks up to certain levels of erasure, the reagent 5 g copper sulphate, 60 ml water, 30 ml concentrated ammonium hydroxide and 60 ml concentrated hydrochloric acid restored marks erased to a depth of 0.04 mm below the engraving depth, thus presenting itself the most sensitive reagent. Quite significantly, the above reagent was also able to decipher successfully the original engraved marks that had been erased and engraved with a new number, or obliterated by centre punching. The results of this research work should benefit the forensic practitioners engaged in the serial number recovery on vehicles, firearms and other objects.
Detection of diatom frustules in bone marrow (diatom test) is used for diagnosing ante-mortem drowning where the usual signs of drowning are not present in dead bodies recovered from water. However, controversies over the reliability of diatom test results are continuing. There have been indications on the possibilities of diatoms entering into systemic circulation from atmospheric air, food and drink. While diatoms have been demonstrated in the gut content of edible marine forms such as shrimps and clams, the present study, for the first time, provides empirical evidence on the prevalence as well as abundance of diatom frustules in the samples of cooked non-vegetarian foodstuffs that impend human consumption in Kelantan, Malaysia. It is found that 50 g each of cleaned and cooked prawns and of clams impending human consumption contain about 8360 and 29,054 diatom frustules, respectively. A person accustomed to prawn and clam food would be ingesting an estimated 2 million diatoms in a single year. Considering the suggestion that detection of five diatom frustules in 10 g of bone marrow would suffice for concluding drowning as mode of death, and the fact that there is yet no proof that diatom frustules do not enter into the human systemic circulation through the digestive tract, the estimated number of diatom frustules routinely ingested acquires significance since entry of a few of such ingested frustules into the systemic circulation can lead to false positive test results. The findings of this research raise two important issues: first, population based routine food related diatom ingestion requires to be estimated, and, second, studies have to be initiated to categorically prove or disprove the possibility of entry of diatom frustules into the systemic circulation via the digestive tract.
The use of STR multiplexes with the incorporated gender marker Amelogenin is common practice in forensic DNA analysis. However, when a known male sample shows a dropout of the Amelogenin Y-allele, the STR system falsely genotypes it as a female. To date, our laboratory has observed 18 such cases: 12 from our Y-STR database and six from casework. A study on 980 male individuals in the Malaysian population using the AmpFlSTR Y-filer has revealed a distinct Y-chromosome haplotype associated with the Amelogenin nulls. Our results showed that whilst the Amelogenin nulls were noticeably absent among the Chinese, both the Indians and Malays exhibited such mutations at 3.2 and 0.6%, respectively. It was also found that the Amelogenin negative individuals predominantly belonged to the J2e lineage, suggesting the possibility of a common ancestor for at least some of these chromosomes. The null frequencies showed concordance with the data published in Chang et al. [Higher failures of Amelogenin sex test in an Indian population group, J. Forensic Sci. 48 (2003) 1309-1313] on a smaller Malaysian population of 338 males which used a Y-STR triplex. In the current study, apart from the absence of the Amelogenin Y-locus, a complete absence of the DYS458 locus in all the nulls was also observed. This study together with the 2003 study has indicated a similar deletion region exists on the Y(p)11.2 band in all the 18 Y-chromosomes. Using bioinformatics, this deletion has been mapped to a region of at least 1.13 Mb on the Y(p)11.2 encompassing the Amelogenin, MSY1 minisatellite and DYS458 locus. Further, the Y-filer haplotypes revealed an additional null at Y-GATA H4 in two of the Indian males presented here.
We have analyzed 16 Y-STR loci (DYS456, DYS389I, DYS390, DYS389II, DYS458, DYS19, DYS385a/b, DYS393, DYS391, DYS439, DYS635 or Y-GATA C4, DYS392, Y-GATA H4, DYS437, DYS438 and DYS448) from the non-recombining region of the human Y-chromosome in 980 male individuals from three main ethnic populations in Malaysia (Malay, Chinese, Indian) using the AmpFlSTR((R)) Y-filertrade mark (Applied Biosystems, Foster City, CA). The observed 17-loci haplotypes and the individual allele frequencies for each locus were estimated, whilst the locus diversity, haplotype diversity and discrimination capacity were calculated in the three ethnic populations. Analysis of molecular variance indicated that 88.7% of the haplotypic variation is found within population and 11.3% is between populations (fixation index F(ST)=0.113, p=0.000). This study has revealed Y-chromosomes with null alleles at several Y-loci, namely DYS458, DYS392, DYS389I, DYS389II, DYS439, DYS448 and Y-GATA H4; and several occurrences of duplications at the highly polymorphic DYS385 loci. Some of these deleted loci were in regions of the Y(q) arm that have been implicated in the occurrence of male infertility.
Allele frequencies for the 13 CODIS (Combined DNA Index System, USA) STR loci included in the AmpFISTR Profiler Plus and AmpFISTR Cofiler kits (Applied Biosystems, Foster City, USA) were determined in a sample of 197 unrelated Malays in Singapore.
Mitragyna speciosa, a native plant of Thailand and Malaysia known as 'ketum', is a plant of considerable interest. It exhibits strong antinociceptive effect and yet, acts like a psychostimulant. Due to the affordability and its ease of availability, the abuse of this plant as a substitute for other banned narcotics has become a major concern in many societies. In countries such as Thailand, Myanmar, Australia and Malaysia, the use of ketum is illegal. However, for a person to be charged for possessing or selling ketum, a reliable analytical method is needed in order to detect and identify the plant and its products. Mitragynine is the major alkaloid of ketum. This compound manifests its antinociceptive effects by acting on the opioid receptors. Since M. speciosa contain large quantity of mitragynine and it is exclusive to the species, the present analytical method is developed and validated for the purpose of screening ketum products based on this unique compound as the analytical marker. The method uses a HPLC-DAD system with Inertsil C8 (4.6 mm × 150 mm, 5 μm) as the column and a mixture of acetonitrile and formic acid, 50:50 (v/v), as the mobile phase. This method not only detects mitragynine, it can also be used to quantify the amount of mitragynine in the sample. The limit of detection is 0.25 μg/ml, while the limit of quantification is 0.50 μg/ml. The method is quick, simple and reliable with an accuracy of 97.27-101.74% and coefficient of variations of between 0.91 and 3.96%. The method has been tested and found suitable for the identification and quantification of mitragynine in dried plants, a variety of ketum extracts, as well as ketum drink obtained from the market.
A series of experiments was conducted by exposing negative film in brand new cameras of different make and model. The exposures were repeated at regular time intervals spread over a period of 2 years. The processed film negatives were studied under a stereomicroscope (10-40x) in transmitted illumination for the presence of the characterizing features on their four frame-edges. These features were then related to those present on the masking frame of the cameras by examining the latter in reflected light stereomicroscopy (10-40x). The purpose of the study was to determine the origin and permanence of the frame-edge-marks, and also the processes by which the marks may probably alter with time. The investigations have arrived at the following conclusions: (i) the edge-marks have originated principally from the imperfections received on the film mask from the manufacturing and also occasionally from the accumulated dirt, dust and fiber on the film mask over an extended time period. (ii) The edge profiles of the cameras have remained fixed over a considerable period of time so as to be of a valuable identification medium. (iii) The marks are found to be varying in nature even with those cameras manufactured at similar time. (iv) The influence of f/number and object distance has great effect in the recording of the frame-edge marks during exposure of the film. The above findings would serve as a useful addition to the technique of camera edge-mark comparisons.
Craniofacial superimposition, although existing for one century, is still a controversial technique within the scientific community. Objective and unbiased validation studies over a significant number of cases are required to establish a more solid picture on the reliability. However, there is lack of protocols and standards in the application of the technique leading to contradictory information concerning reliability. Instead of following a uniform methodology, every expert tends to apply his own approach to the problem, based on the available technology and deep knowledge on human craniofacial anatomy, soft tissues, and their relationships. The aim of this study was to assess the reliability of different craniofacial superimposition methodologies and the corresponding technical approaches to this type of identification. With all the data generated, some of the most representative experts in craniofacial identification joined in a discussion intended to identify and agree on the most important issues that have to be considered to properly employ the craniofacial superimposition technique. As a consequence, the consortium has produced the current manuscript, which can be considered the first standard in the field; including good and bad practices, sources of error and uncertainties, technological requirements and desirable features, and finally a common scale for the craniofacial matching evaluation. Such a document is intended to be part of a more complete framework for craniofacial superimposition, to be developed during the FP7-founded project MEPROCS, which will favour and standardize its proper application.
The ability to objectify ballistic evidence is a challenge faced by firearms examiners around the world. A number of researchers are trying to improve bullet-identification systems to address deficiencies detailed within the National Academy of Science report (2009). More recently focus has turned to making use of more sophisticated imaging modalities to view entire regions of the projectile and the development of automated systems for the comparison of the topographical surfaces recorded. Projectiles from a newly bought air pistol with 0.177 calibre pellets (unjacketed), fired series of 609 pellets were examined using an optical microscope. A mathematical methodology was developed to pre-process the resultant topographical maps generating point data for comparison, analysed using the principal component analysis (PCA). In most cases limited to reasonable success was achieved. The objective method still requires an operator to identify the Land Engraved Areas to be scanned, however the mathematical alignments were objectively achieved. The PCA results illustrated that the striation marks were neither exclusive nor specific to the LEA regions but rather crossed over regions. This study also proves that a single weapon does not necessarily leave identical marks of projectiles on its surface.
Camera attribution plays an important role in digital image forensics by providing the evidence and distinguishing characteristics of the origin of the digital image. It allows the forensic analyser to find the possible source camera which captured the image under investigation. However, in real-world applications, these approaches have faced many challenges due to the large set of multimedia data publicly available through photo sharing and social network sites, captured with uncontrolled conditions and undergone variety of hardware and software post-processing operations. Moreover, the legal system only accepts the forensic analysis of the digital image evidence if the applied camera attribution techniques are unbiased, reliable, nondestructive and widely accepted by the experts in the field. The aim of this paper is to investigate the evolutionary trend of image source camera attribution approaches from fundamental to practice, in particular, with the application of image processing and data mining techniques. Extracting implicit knowledge from images using intrinsic image artifacts for source camera attribution requires a structured image mining process. In this paper, we attempt to provide an introductory tutorial on the image processing pipeline, to determine the general classification of the features corresponding to different components for source camera attribution. The article also reviews techniques of the source camera attribution more comprehensively in the domain of the image forensics in conjunction with the presentation of classifying ongoing developments within the specified area. The classification of the existing source camera attribution approaches is presented based on the specific parameters, such as colour image processing pipeline, hardware- and software-related artifacts and the methods to extract such artifacts. The more recent source camera attribution approaches, which have not yet gained sufficient attention among image forensics researchers, are also critically analysed and further categorised into four different classes, namely, optical aberrations based, sensor camera fingerprints based, processing statistics based and processing regularities based, to present a classification. Furthermore, this paper aims to investigate the challenging problems, and the proposed strategies of such schemes based on the suggested taxonomy to plot an evolution of the source camera attribution approaches with respect to the subjective optimisation criteria over the last decade. The optimisation criteria were determined based on the strategies proposed to increase the detection accuracy, robustness and computational efficiency of source camera brand, model or device attribution.
Evidence in crime scenes available in the form of biological stains which cannot be visualized during naked eye examination can be detected by imaging their fluorescence using a combination of excitation lights and suitable filters. These combinations selectively allow the passage of fluorescence light emitted from the targeted stains. However, interference from the fluorescence generated by many of the surface materials bearing the stains often renders it difficult to visualize the stains during forensic photography. This report describes the use of background correction algorithm (BCA) to enhance the visibility of seminal stain, a biological evidence that fluoresces. While earlier reports described the use of narrow band-pass filters for other fluorescing evidences, here, we utilize BCA to enhance images captured using commonly available colour filters, yellow, orange and red. Mean-based contrast adjustment was incorporated into BCA to adjust the background brightness for achieving similarity of images' background appearance, a crucial step for ensuring success while implementing BCA. Experiment results demonstrated the effectiveness of our proposed colour filters' approach using the improved BCA in enhancing the visibility of seminal stains in varying dilutions on selected surfaces.
Considering that crimes against animals such as illegal killing and cruelty have been alarmingly increasing and since burning is one of the common ways for disposing cadavers, ability to estimate minimum postmortem interval (PMI) using entomological data merits consideration. Chrysomya megacephala and Chrysomya rufifacies are common necrophagous species recovered from cadavers in many countries including Malaysia. Specific studies focusing on the oviposition and developmental patterns of both species on cadavers manifesting different levels of burn as described by the Crow-Glassman Scale (CGS) remain scarce. In four replicates, rabbit carcasses were burned to CGS levels #1, #2 and #3 by varying the amount of petrol used and duration of burning. Oviposition by C. megacephala and C. rufifacies was delayed by one day in the case of carcasses burned to the CGS level #3 (p<0.05) when compared with that of controls. Such delay in oviposition was not observed in the CGS level #1 and #2 carcasses. No significant differences (p>0.05) in the duration of development were found between control and burned carcasses. These findings deserve consideration while estimating minimum PMI since burning as a mean for disposing animal and human cadavers is gaining popularity.
As part of the scientific tasks coordinated throughout The 'New Methodologies and Protocols of Forensic Identification by Craniofacial Superimposition (MEPROCS)' project, the current study aims to analyse the performance of a diverse set of CFS methodologies and the corresponding technical approaches when dealing with a common dataset of real-world cases. Thus, a multiple-lab study on craniofacial superimposition has been carried out for the first time. In particular, 26 participants from 17 different institutions in 13 countries were asked to deal with 14 identification scenarios, some of them involving the comparison of multiple candidates and unknown skulls. In total, 60 craniofacial superimposition problems divided in two set of females and males. Each participant follow her/his own methodology and employed her/his particular technological means. For each single case they were asked to report the final identification decision (either positive or negative) along with the rationale supporting the decision and at least one image illustrating the overlay/superimposition outcome. This study is expected to provide important insights to better understand the most convenient characteristics of every method included in this study.
A research that tested the methods suitable for comparing ante- and post-mortem radiographic patterns of frontal sinuses concluded that superimposition should be followed as a stringent method for establishing individual identification. We verified the practical relevance of prescribing superimposition by superimposing ante- and post-mortem frontal sinus patterns recorded in case situations as well as simulated ante- and post-mortem of frontal sinus patterns recorded using archived skulls. For superimposition, the wipe facility available in the vision mixer was employed in addition to the mix mode. Ante- and post-mortem radiographic patterns that were available in two earlier cases were not superimposable. Related simulated ante- and post-mortem radiographic patterns of frontal sinuses are superimposable only when the skull that is initially oriented for recording the ante-mortem radiograph is retained in the same posture for recording the post-mortem radiograph also. Once the skull has been removed from the X-ray table, after recording the simulated ante-mortem radiograph, and repositioned for the simulated post-mortem radiograph, even when the intervening time is 1min, the sinus patterns in these radiographs are not superimposable. Superimposition cannot be used as a conditional requirement for side-by-side comparison of radiographic patterns of frontal sinuses.
Video vision mixer based skull-photo superimposition is a popular method for identifying skulls retrieved from unidentified human remains. A report on the reliability of the superimposition method suggested increased failure rates of 17.3 to 32% to exclude and 15 to 20% to include skulls while using related and unrelated face photographs. Such raise in failures prompted an analysis of the methods employed for the research. The protocols adopted for assessing the reliability are seen to vary from those suggested by the practitioners in the field. The former include overlaying the skull- and face-images on the basis of morphology by relying on anthropometric landmarks on the front plane of the face-images and evaluating the goodness of match depending on mix-mode images; the latter consist of orienting the skull considering landmarks on both the eye and ear planes of the face- and skull-images and evaluating the match utilizing images seen in wipe-mode in addition to those in mix-mode. Superimposition of a skull with face-images of five living individuals in two sets of experiments, one following the procedure described for the research on reliability and the other applying the methods suggested by the practitioners has shown that overlaying the images on the basis of morphology depending on the landmarks on the front plane alone and assessing the match in mix-mode fails to exclude the skull. However, orienting the skull relying on the relationship between the anatomical landmarks on the skull- and face-images such as Whitnall's tubercle and exocanthus in the front (eye) plane and the porion and tragus in the rear (ear) plane as well as assessing the match using wipe-mode images enables excluding that skull while superimposing with the same set of face-images.
Allele frequencies for the nine STRs genetic loci included in the AmpFlSTR Profiler kit were obtained from samples of unrelated individuals comprising 139-156 Malays, 149-153 Chinese and 132-135 Indians, residing in Malaysia.
A case is presented in which a camera recovered from a site of bomb blast was linked to some incriminating film negatives by the characteristic markings existing along a small portion of the edge of the film negatives.
The distributions of the D1S80 alleles and genotypes in the Chinese, Malays and Indians in Singapore were determined by amplified fragment length polymorphism (AMP-FLP) analysis. The distributions of the observed genotypes for the three races conformed to Hardy-Weinberg expectations. The system was applied to 19 families whose paternity had been established by restriction fragment length polymorphism (RFLP) analysis. In all cases, Mendelian inheritance of the alleles at the D1S80 locus could be demonstrated. D1S80 typing on DNA recovered by differential extraction of forensic specimens which included vaginal swabs, urethral swabs and seminal stains yielded consistent results.
Opium dependence was indigenous to countries in the Golden Triangle area in south-east Asia (SA). Heroin epidemics developed in most SA countries in the 1960s and early 1970s and remained a significant problem particularly in Myanmar, Thailand and Malaysia until now. In contrast, the island countries in SA seemed quite free from opiate abuse. Intravenous injection (IV) of drugs appeared after the heroin epidemic and currently prevails in countries with a significant opiate abuse problem. IV of opium was particularly common in the highly urbanized cities in Vietnam. Most SA countries started HIV seroscreening in IV drug users (IVDU) around the middle of the 1980s. Rapid epidemic spread of HIV infection was observed in 1988-89 in Thailand and Myanmar. The Highest prevalence of more than 80% was reported from a study of IVDUs in Yangon, Myanmar, followed by Thailand at about 40%. Although HIV infected IVDUs were identified at the same time in Malaysia and later in Singapore and the Philippines, there was no evidence of such a rapid and severe epidemic.
Allele frequencies for the 15 STR loci in the AmpFlSTR Identifiler kit were determined and compared for the three main ethnic groups of the Malaysian population comprising 210 Malays, 219 Chinese and 209 Indians. Blood was placed on FTA paper and DNA was purified in-situ.