Polyaniline composites consisting of carboxymethyl cellulose (CMC) have enhanced adsorption properties, but recent studies indicate that the oxidised species - dialdehyde carboxymethyl cellulose (DCMC) - outperforms CMC-based composites. However, these studies fail to study the effect of DCMC's aldehyde content and compare the composites with CMC-based composites; numerous experiments required to investigate each adsorbent for each factor limit such studies. We explored a way to study whether villi-structured polyaniline (VSPANI), its CMC composite (CMC/PANI), and its DCMC composites with 35% (DCMC(A)/PANI) and 77% (DCMC(B)/PANI) aldehyde content would be great adsorbents for removing bisphenol-A (BPA). We first customised a D-optimal screening design to alleviate the pitfalls of definitive screening design (DSD), hence estimating all the main effects: initial concentration, pH, flow rate, adsorbent amount, sample volume and type of adsorbent. We excluded CMC/PANI and DCMC(A)/PANI composites, both with low adsorption capacities of 56.57 and 57.27 mg/g from further investigation. The DSD followed to estimate all second-order effects through which we projected a response surface method (RSM) to optimise and model the active factors. Increasing the aldehyde content on the composites favoured adsorption, but there lacked evidence to suggest VSPANI and DCMC(B)/PANI differed significantly in performance. The models were numerically and graphically proven adequate, explaining 80% and 99% of the variation when predicting removal efficiency and adsorption capacity. VSPANI showed potential as an adsorbent for BPA removal with 85% removal efficiency and 129 mg/g adsorption capacity. This comprehensive approach, combining both designs, allows for sustainable investigation of multiple adsorbents and factors, minimising experimental waste.
The objective of this study is to evaluate the performance of sequencing batch biofilm reactors (SBBRs) and sequencing batch reactor (SBR) in the simultaneous removal of p-nitrophenol (PNP) and ammoniacal nitrogen. SBBRs involved the use of polyurethane sponge cubes and polyethylene rings, respectively, as carrier materials. The results demonstrate that complete removal of PNP was achievable for the SBR and SBBRs up to the PNP concentration of 350 mg/l (loading rate of 0.368 kg/m3 d). At this loading rate, the average ammoniacal nitrogen removal efficiency for the SBR and SBBR (with polyethylene rings) was reduced to 86% and 96%, respectively. However, the SBBR (with polyurethane sponge cubes) still managed to achieve an almost 100% ammoniacal nitrogen removal. Based on the results, the performance of the SBBRs was better than that of SBR in PNP and ammoniacal nitrogen removal. The results of the gas chromatography mass spectroscopy, high-performance liquid chromatography and ultraviolet-visible analyses indicate that complete mineralization of PNP was achieved in all of the reactors.
The scarcity of energy and water resources is a major challenge for humanity in the twenty-first century. Engineered osmosis (EO) technologies are extensively researched as a means of producing sustainable water and energy. This study focuses on the modification of substrate properties of thin film nanocomposite (TFN) membrane using aluminium oxide (Al2O3) nanoparticles and further evaluates the performance of resultant membranes for EO process. Different Al2O3 loading ranging from zero to 0.10 wt% was incorporated into the substrate and the results showed that the hydrophilicity of substrate was increased with contact angle reduced from 74.81° to 66.17° upon the Al2O3 incorporation. Furthermore, the addition of Al2O3 resulted in the formation of larger porous structure on the bottom part of substrate which reduced water transport resistance. Using the substrate modified by 0.02 wt% Al2O3, we could produce the TFN membrane that exhibited the highest water permeability (1.32 L/m2.h.bar, DI water as a feed solution at 15 bar), decent salt rejection (96.89%), low structural parameter (532.44 μm) and relatively good pressure withstandability (>25 bar).
The potential of selected materials in treating metal-rich acid mine drainage (AMD) has been investigated in a series of batch experiment. The efficiencies of both single and mixed substrates under two conditions i.e. low- and high-concentration solutions containing heavy metals were evaluated. Synthetic metal-containing AMD was used in the experiments treated using spent mushroom compost (SMC), ochre, steel slag (SS), and limestone. Different ratios of treatment materials were incorporated in the substrate mix and were tested in an anoxic condition. In the batch test, physicochemical parameters (pH, redox potential, total dissolved solids, conductivity, and Ca concentration) and heavy metals (Fe, Mn, Pb, Zn, and Al) were analysed. The mixed substrates have shown satisfactory performance in increasing pH with increasing Ca concentration and removing metals. It has been found that SS and ochre played an important role in the treatment of AMD. The results showed that the mixed substrates SM1 (i.e. 10% SMC mixed with 20% ochre, 30% steel slag, and 40% limestone) and SM2 (i.e. 20% SMC mixed with 30% ochre, 40% steel slag, and 10% limestone) were effective in increasing the pH from as low as 3.5-8.09, and removing heavy metals with more than 90% removal efficiencies.
Biological aerated filter (BAF), sand filtration (SF), alum and Moringa oleifera coagulation were investigated as a pre-treatment for reducing the organic and biofouling potential component of an ultrafiltration (UF) membrane in the treatment of lake water. The carbohydrate content was mainly responsible for reversible fouling of the UF membrane compared to protein or dissolved organic carbon (DOC) content. All pre-treatment could effectively reduce these contents and led to improve the UF filterability. Both BAF and SF markedly led to improvement in flux than coagulation processes, and alum gave greater flux than M. oleifera. This was attributed to the effective removal and/or breakdown of high molecular weight (MW) organics by biofilters. BAF led to greater improvement in flux than SF, due to greater breakdown of high MW organics, and this was also confirmed by the attenuated total reflection-Fourier transform infrared spectroscopy analysis. Coagulation processes were ineffective in removing biofouling potential components, whereas both biofilters were very effective as shown by the reduction of low MW organics, biodegradable dissolved organic carbon and assimilable organic carbon contents. This study demonstrated the potential of biological pre-treatments for reducing organic and biofouling potential component and thus improving flux for the UF of lake water treatment.
This study demonstrated the generation of clean water from seawater collected at the beach coast in Universiti Malaysia Sabah, Malaysia, with carbonized rice husk coated melamine sponge as solar absorber by a solar still. Melamine sponge was utilized as a seawater transportation medium since its porous structure is excellent in channelling the seawater. Whereas carbonized rice husk was used as the photothermal conversion material for its efficient heat absorption due to its black colour and porous structure. Implementing air gap between the seawater body and solar absorber, and restricted water pathway assisted in localizing heat on the top surface of the solar absorber. Clean water was generated under direct solar radiation during the day at an open space with average solar intensity around 1.1∼1.2 kW/m2 (slightly higher than 1 sun) for about 4 h. Efficiency of the solar absorber was calculated, while the quality of the generated clean water was observed in terms of salinity and pH value. Insulated solar still with carbon-coated sponge showed the highest efficiency at about 54.74%. Salinity of the collected clean water significantly reduced to consumable level which was approximately 55 ppm, and the pH value at about 6.73 where it was within the safe limit of the drinkable water pH.
In the work presented here, photocatalytic systems using TiO2 and ZnO suspensions were utilized to evaluate the degradation of resorcinol (ReOH). The effects of catalyst concentration and solution pH were investigated and optimized using multivariate analysis based on response surface methodology. The results indicated that ZnO showed greater degradation and mineralization activities compared to TiO2 under optimized conditions. Using certain radical scavengers, a positive hole, together with the participation of hydroxyl radicals, were the oxidative species responsible for ReOH degradation on TiO2 whereas, the ZnO photocatalysis occurred principally via hydroxyl radicals. Some hitherto unreported pathway intermediates of ReOH degradation were identified using gas chromatography-mass spectrometry. A tentative reaction mechanism for the formation of these intermediates was proposed. Moreover, the figure-of-merit electrical energy per order was employed to estimate the electrical energy consumption.
Para-arsanilic acid (p-ASA) has been widely used in the poultry industry to promote growth and prevent dysentery. It is excreted unchanged in the manure and released into non-target sites causing organoarsenic pollution risk to the environment and living system. Therefore, simple and effective analytical strategies are demanded for determining the samples that contain p-ASA. However, direct determination of both p-ASA and ortho-arsanilic acid (o-ASA) using differential pulse cathodic stripping voltammetry (DPCSV) gives the similar voltammograms that directly hamper the analysis used by the DPCSV technique. In this study, a method to determine and differentiate p-ASA from o-ASA via diazotization and coupling reaction of the amine groups followed by the direct DPCSV determination of diazo compounds is presented. The diazotization reaction carried out at pH 1.5 and 0 ± 1°C for 10 min showed two reduction peaks in DPCSV at-70 mV and -440 mV vs. Ag/AgCl (KCl 3 M). However, when the diazotization reaction was performed at pH 12.5 and 0 ± 1°C for 40 min, a coloured azo compound was produced and the DPCSV showed only one reduction peak that appeared at -600 mV vs. Ag/AgCl (3 M of KCl). The results of this study show that only p-ASA compound gave a reduction peak, whereas o-ASA compound did not give any peak. The detection limit of p-ASA was found to be 4 × 10(-8 )M. As a result, the proposed electro-analytical technique might be a good candidate to determine and differentiate the p-ASA present in the poultry and environmental samples.
In the present investigation, a total of 108 combinations of ionic liquids (ILs) were screened using the conductor-like screening model for real solvents (COSMO-RS) with the aid of six cations and eighteen anions for the extraction of succinic acid (SA) from aqueous streams through dispersive liquid-liquid microextraction (DLLME). Using the screened ILs, an ionic liquid-based DLLME (IL-DLLME) was developed to extract SA and the role of different reaction parameters in the effectiveness of IL-DLLME approach was investigated. COSMO-RS results suggested that, quaternary ammonium and choline cations form effective IL combinations with [OH¯], [F¯], and [SO42¯] anions due to hydrogen bonding. In view of these results, one of the screened ILs, tetramethylammonium hydroxide [TMAm][OH] was chosen as the extractant in IL-DLLME process and acetonitrile was adopted as the dispersive solvent. The highest SA removal efficiency of 97.8% was achieved using 25 μL of IL [TMAm][OH] as a carrier and 500 μL of acetonitrile as dispersive solvent. The highest amount of SA was extracted with a stir time of 20 min at 300 rpm, followed by centrifugation for 5 min at 4500 rpm. Overall, the findings showed that IL-DLLME is efficient in extracting succinic acid from aqueous environments while adhering to the first-order kinetics.
Understanding of mass transfer kinetics is important for biosorption of nitrogen compounds from palm oil mill effluent (POME) to gain a mechanistic insight into future biological processes for the treatment of high organic loading wastewater. In this study, the rates of global and sequential mass transfer were determined using the modified mass transfer factor equations for the experiments to remove nitrogen by aerobic granular sludge accumulation in a sequencing batch reactor (SBR). The maximum efficiencies as high as 97% for the experiment run at [kLa]g value of 1421.8 h-1 and 96% for the experiment run at [kLa]g value of 9.6 × 1037 h-1 were verified before and after the addition of Serratia marcescens SA30, respectively. The resistance of mass transfer could be dependent on external mass transfer that controls the transport of nitrogen molecule along the experimental period of 256 days. The increase in [kLa]g value leading to increased performance of the SBR was verified to contribute to the future applications of the SBR because this phenomenon provides new insight into the dynamic response of biological processes to treat POME.
Organophosphates (OPs) and synthetic pyrethroids (SPs) are the most popular broad spectrum pesticides, used in agriculture as they have a strong pesticidal activity while also being biodegradable in the environment. The present study aimed to demonstrate the effects of these pesticides on the Acetylcholinesterase (AChE) activity in brain, gills and body muscles of Oreochromis niloticus - an important enzyme for the assessment and biomonitoring pollution caused by neurotoxins in the environment. The fish were exposed for 24 and 48 h to the LC0 concentrations of the malathion (1.425 mg/L), the chlorpyrifos (0.125 mg/L) and the λ-cyhalothrin (0.0039 mg/L), respectively. The activity of the AChE was significantly increased (p
In this study, the zinc oxide (ZnO) layer was synthesised on the surface of Zn plates by three different techniques, i.e. electrolysis, hydrogen peroxide and heat treatment. The synthesised ZnO layers were characterised using scanning electron microscopy, X-ray diffraction, UV-visible diffuse reflectance and photoluminescence spectroscopy. The photocatalytic activity of the ZnO layer was further assessed against methylene blue (MB) degradation under UV irradiation. The photocatalytic degradation of MB was achieved up to 84%, 79% and 65% within 1 h for ZnO layers synthesised by electrolysis, heat and hydrogen peroxide treatment, respectively. The reusability results show that electrolysis and heat-treated ZnO layers have considerable photocatalytic stability. Furthermore, the results confirmed that the photocatalytic efficiency of ZnO was directly associated with the thickness and enlarged surface area of the layer. Finally, this study proved that the ZnO layers synthesised by electrolysis and heat treatment had shown better operational stability and reusability.
The aqueous extract of various plants like Coriandrum sativum (AECS), Alternanthera tenella colla (AEAT), Spermacoce hispida (AESH) and Mollugo verticillata (AEMV) was studied for its hexavalent chromium (CrVI) reduction property. Even though antioxidant activity was present, AEAT, AESH and AEMV did not reduce CrVI. AECS showed rapid and dose-dependent CrVI reduction. The efficient reduction of 50 mg/L of CrVI using AECS was attained in the presence of 250 µg/mL of starting plant material, incubating the reaction mixture at pH 2, 30°C and agitation at 190 rpm. Under such conditions, about 40 mg/L of CrVI was reduced at 3 h of incubation. FT-IR analysis revealed the involvement of phenols, alcohols, alpha-hydroxy acid and flavonoids present in the AECS for the CrVI reduction. These results indicate that not all the plant extracts with rich antioxidants are capable of reducing CrVI. Using the conditions standardized in the present study, AECS reduced about 80% of CrVI present in the tannery effluent. These results signify the application of AECS as an eco-friendly method in the wastewater treatment.
Effluent containing colour/dyes, especially reactive dyes, becomes a great concern of wastewater treatment because it is toxic to human life and aquatic life. In this study, reactive dye of Black B was separated using the supported liquid membrane process. Commercial polypropylene membrane was used as a support of the kerosene-tridodecylamine liquid membrane. Several parameters were tested and the result showed that almost 100% of 70 ppm Black B was removed and 99% of 70 ppm Black B was recovered at pH 2 of the feed phase containing 0.00001 M Na2SiO3, flow rate of 150 ml/min and 0.2 M NaOH. The membrane support also remained stable for up to 36 hours under an optimum condition.
Microbiologically influenced corrosion (MIC) is among the common corrosion types for buried and deep-water pipelines that result in costly repair and pipeline failure. Sulfate-reducing bacteria (SRB) are commonly known as the culprit of MIC. The aim of this work is to investigate the performance of combination of ultrasound (US) irradiation and ultraviolet (UV) radiation (known as Hybrid soliwave technique, HyST) at pilot scale to inactivate SRB. The influence of different reaction times with respect to US irradiation and UV radiation and synergistic effect toward SRB consortium was tested and discussed. In this research, the effect of HyST treatment toward SRB extermination and corrosion studies of carbon steel coupon upon SRB activity before and after the treatment were performed using weight loss method. The carbon steel coupons immersed in SRB sample were exposed to HyST treatment at different time of exposure. Additionally, Field Emission Scanning Electron Microscopy coupled with Energy Dispersive X-ray Spectroscopy were used to investigate the corrosion morphology in verifying the end product of SRB activity and corrosion formation after treatment. Results have shown that the US irradiation treatment gives a synergistic effect when combined with UV radiation in mitigating the SRB consortium.
There is limited information on the optimal processes to remove heavy metals in greywater. A Response Surface Methodology (RSM) via the Box-Behnken Design (BBD) approach was applied in this study to investigate and optimise the process variables of activation time (1.5-2.5 h), impregnation ratio (0.25-0.75) and zinc chloride (ZnCl2) percentage (20-60%) for the removal of heavy metal ions (Cd, Cu, Pb and Ni) associated with greywater treatment. The quadratic model was chosen to describe the effects of the process variables (activation time, impregnation ratio, ZnCl2 percentage) on predicting the responses (heavy metal ions removal) with low p-values (
Magnetic nanocomposites adorned with calixarene were successfully prepared by immobilizing diethanolamine functionalized p-tert-butylcalix[4]arene (DEA-Calix) onto silica-coated magnetic nanoparticles (MNPs). The synthesis, surface morphology, purity, elemental composition and thermal stability of newly prepared nanocomposites were analyzed using FT-IR spectroscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDX), X-ray diffractometer (XRD), thermal gravimetric analysis (TGA) and vibrating sample magnetometer (VSM). Magnetic solid-phase adsorption (MSPA) was employed to explore the adsorption behavior of DEA-Calix-MNPs towards Pb(II) from water samples prior to its flame atomic absorption spectrometric analysis. The essential analytical factors governing the adsorption efficiency such as solution pH, mass of adsorbent, concentration and contact time have been investigated and optimized. The results depict that DEA-Calix-MNPs has excellent adsorption efficiency 97% (at pH 5.5) with high adsorption capacity of 51.81 mg g-1 for Pb(II) adsorption. Additionally, kinetic and equilibrium studies suggested that Pb(II) adsorption process follows a pseudo-second-order model and Langmuir isotherms, respectively. Real sample analysis also confirmed field applicability of the new DEA-Calix-MNPs adsorbent.
The objective of this study was to evaluate the effects ofNi(II) and Cr(VI) individually and in combination on the simultaneous removal of chemical oxygen demand (COD), nitrogen and metals under a sequencing batch reactor (SBR) operation. Three identical laboratory-scale SBRs were operated with FILL, REACT, SETTLE, DRAW and IDLE periods in a ratio of 1:12:1:2:8 for a cycle time of 24 h until the steady state was achieved. Nickel(II) at increasing concentrations up to 35 mg/L was added to one of the reactors; Cr(VI) at increasing concentrations up to 25 mg/L was added to a second reactor; while a combination of Ni(II) and Cr(VI) in equal concentrations up to 10 mg/L was added to a third reactor. The results demonstrate that both Ni(II) and Cr(VI) exerted a more pronounced inhibitory effect on the removal of ammonia nitrogen (AN) than on COD removal. Synergistic and antagonistic inhibitory effects on the rates of COD and AN removal, respectively, were observed for the 50% Ni(II) and 50% Cr(VI) (w/w) mixture in the concentration range between 10 and 20 mg/L. The simultaneous presence of 50% Ni(II) and 50% Cr(VI) at a concentration of 20 mg/L resulted in system failure.
The objective of this research was to evaluate the treatment ofp-nitrophenol (PNP) as a sole organic carbon source using a sequencing batch reactor (SBR) with the addition of adsorbent. Two types of adsorbents, namely powdered activated carbon (PAC) and pyrolysed rice husk (PRH) were used in this study. Two identical SBRs, each with a working volume of 10 L, were operated with fill, react, settle, draw and idle periods in the ratio of 2:8:1:0.75:0.25 for a cycle time of 12 h. The results showed that, without the addition of adsorbent, increasing the influent PNP concentration to 200 mg/L resulted in the deterioration of chemical oxygen demand (COD) removal efficiency and PNP removal efficiency in the SBRs. Improvement in the performance of the SBR was observed with the addition of PAC. When the dosage of 1.0 g PAC/cycle was applied, COD removal of 95% and almost complete removal of PNP were achieved at the influent PNP concentration of 300 mg/L. The kinetic study showed that the rates of COD and PNP removal can be described by the first-order kinetics. The enhancement of performance in the PAC-supplemented SBR was postulated to be due to the initial adsorption of PNP by the freshly added and the bioregenerated PAC, thus reducing the inhibition on the microorganisms. The PRH was found to be ineffective because of its relatively low adsorption capacity for PNP, compared with that of PAC.
The present work reports the extraction of phenolic compounds from Polygonum minus using ionic liquid as extracting solvent. In this work, 1-Butyl-3-methylimidazolium hydrogen sulfate [BMIM][HSO4] was used for the extraction of bioactive compounds. Accordingly, ionic liquids based microwave-assisted extraction treatment for separating of bioactive compounds from polygonum minus was first performed in the present study. The results obtained in this work have high extraction yield in comparison with conventional solvent. UV/Vis results showed that microwave synthesis was fast, well dispersed and nanosized copper nanoparticle (CuNPs) in comparison with conventional synthesis. CuNPs was characterised by X-Rays diffractometer (XRD), Fourier transform infrared (FTIR), dynamic light scattering (DLS), field emission scanning electron microscopy combined with energy dispersive x-rays (FESEM-EDX), and thermogravimetric analysis (TGA). All the instrumental analyses confirmed the particles were nanosized. Furthermore, the antibacterial activity of as-synthesised CuNPs showed effective inhibitory zone against three different bacteria. The photocatalytic degradation of copper nanoparticles was studied using methylene blue (MB) and methyl orange (MO) dyes under UV light and degraded 99.9% within short time 8 and 7 min.