The effect of metal cations, both nonhydrolyzable and hydrolyzable, on the zeta potential of palm olein emulsions stabilized by the nonionic emulsifier, polyoxyethylene nonyl phenyl ether, was investigated as a function of pH and cation concentrations, respectively. The oil drops were found to be negatively charged in the presence of simple mono- and divalent cations. Charge reversal of the oil drops was observed when hydrolyzable cations (Zn2+, Cu2+, Fe3+, and Al3+) were used and the behavior is strongly dependent on the type of cation, its concentration, and the pH of the dispersion. The results are discussed in terms of current theories of electrophoresis and adsorption-precipitation at interfaces. The chemical free energies of adsorption of the cations were calculated. Copyright 1999 Academic Press.
Kaolin-carbon adsorbents were prepared with and without sulfuric acid pretreatment followed by activation-carbonization at 500 degrees C. The total surface area of the resulting kaolin-carbon adsorbents was found to be decreased with the increase in kaolin loading. Sulfuric acid pretreatment of the precursor prior to the carbonization-activation processes resulted in the enhancement of total surface area but reduced the micropore surface area of the resulting adsorbents. At the same time, this improved carotene adsorption capacity from red palm oil. However, recovery of carotene from the carotene-adsorbed adsorbent is only improved when the acid pretreatment of the precursor was done at a high loading percentage of activated carbon. Similarly, the peroxide value (PV) increased. A maximum removal of carotene from red palm oil was obtained at 20% kaolin loading for both adsorbents prepared with and without sulfuric acid pretreatment with about 45 and 65% carotene removal, respectively, from a 30-ppm solution. This indicates that pretreatment with sulfuric acid, prior to the activation-carbonization process, increased the carotene uptake by the resulting adsorbent. However, a further increase in the kaolin loading resulted in the decrease of carotene removal. About 3-4% of carotene adsorbed can be recovered from both types of adsorbents under optimum condition, in which the percentage recovered decreased with the increase in kaolin loading. On the other hand, the PV increased with kaolin loading at around 54-64 mEq/kg for both types of adsorbents. It was also found that carotene uptake by the adsorbents is high if the adsorbent contains a high percentage of activated carbon. Similarly, carotene recovery is high and less oxidation can be observed, as indicated by the lower PV value. Copyright 2001 Academic Press.
Frictional and nanomechanical properties of nanostructured polymer surfaces are important to their technological and biomedical applications. In this work, poly(ethylene terephthalate) (PET) surfaces with a periodic distribution of well-defined nanopillars were fabricated through an anodization/embossing process. The apparent surface energy of the nanopillared surfaces was evaluated using the Fowkes acid-base approach, and the surface morphology was characterized using scanning electron microscope (SEM) and atomic force microscope (AFM). The normal and lateral forces between a silica microparticle and these surfaces were quantified using colloidal probe atomic force microscopy (CP-AFM). The friction-load relationship followed Amonton's first law, and the friction coefficient appeared to scale linearly with the nanopillar height. Furthermore, all the nanopillared surfaces showed pronounced frictional instabilities compared to the smooth sliding friction loop on the flat control. Performing the stick-slip amplitude coefficient (SSAC) analysis, we found a correlation between the frictional instabilities and the nanopillars density, pull-off force and work of adhesion. We have summarised the dependence of the nanotribological properties on such nanopillared surfaces on five relevant parameters, i.e. pull-off force fp, Amontons' friction coefficient μ, RMS roughness Rq, stick-slip amplitude friction coefficient SSAC, and work of adhesion between the substrate and water Wadh in a radar chart. Whilst demonstrating the complexity of the frictional behaviour of nanopillared polymer surfaces, our results show that analyses of multiparametric nanotribological properties of nanostructured surfaces should go beyond classic Amontons' laws, with the SSAC more representative of the frictional properties compared to the friction coefficient.
Nanopillared surfaces have emerged as a promising strategy to combat bacterial infections on medical devices. However, the mechanisms that underpin nanopillar-induced rupture of the bacterial cell membrane remain speculative. In this study, we have tested three medically relevant poly(ethylene terephthalate) (PET) nanopillared-surfaces with well-defined nanotopographies against both Gram-negative and Gram-positive bacteria. Focused ion beam scanning electron microscopy (FIB-SEM) and contact mechanics analysis were utilised to understand the nanobiophysical response of the bacterial cell envelope to a single nanopillar. Given their importance to bacterial adhesion, the contribution of bacterial surface proteins to nanotopography-mediated cell envelope damage was also investigated. We found that, whilst cell envelope deformation was affected by the nanopillar tip diameter, the nanopillar density affected bacterial metabolic activities. Moreover, three different types of bacterial cell envelope deformation were observed upon contact of bacteria with the nanopillared surfaces. These were attributed to bacterial responses to cell wall stresses resulting from the high intrinsic pressure caused by the engagement of nanopillars by bacterial surface proteins. Such influences of bacterial surface proteins on the antibacterial action of nanopillars have not been previously reported. Our findings will be valuable to the improved design and fabrication of effective antibacterial surfaces.
Bisphenol A (BPA) is highly considered as an emerging contaminants (ECs) due to their endocrine disrupting and reproductive toxicant nature. It has been detected in drinking water sources in many countries. This study deals with the adsorptive removal of BPA using nylon 6,6 nanofibrous membrane (NNM) fabricated by electrospinning technique. Langmuir and Freundlich isotherm models (R2=0.99) were obeyed for BPA adsorption, which indicates the monolayer adsorption of BPA and also surface heterogeneity of NNM. The adsorption kinetics of BPA was followed pseudo second order rate (R2=0.89-0.99), which suggests the occurrence of rapid adsorption rate through interaction of surface functional groups present in NNM. The maximum adsorption of BPA (91.3mgg-1) was attained at 30°C. The hydroxyl groups of BPA form hydrogen bonding with carbonyl groups of NNM during the adsorptive removal process. Reusability study confirmed a much better stability of NNM in the recyclic application. Finally, this study suggests that NNM might be an outstanding nano-adsorbent for the emerging contaminants removal, including BPA from drinking water sources.
Nickel-rich (Ni > 90 %) cathodes are regarded as one of the most attractive because of their high energy density, despite their poor stability and cycle life. To improve their performance, in this study we synthesized a double concentration-gradient layered Li[Ni0.90Co0.04Mn0.03Al0.03]O2 oxide (CG-NCMA) using a continuous co-precipitation Taylor-Couette cylindrical reactor (TCCR) with a Ni-rich-core, an Mn-rich surface, and Al on top. The concentration-gradient morphology was confirmed through cross-sectional EDX line scanning. The as-synthesized sample exhibited excellent electrochemical performance at high rates (5C/10C), as well as cyclability (91.5 % after 100 cycles and 70.3 % after 500 cycles at 1C), superior to that (83.4 % and 47.6 %) of its non-concentration-gradient counterpart (UC-NCMA). The Mn-rich surface and presence of Al helped the material stay structurally robust, even after 500 cycles, while also suppressing side reactions between the electrode and electrolyte, resulting in better overall electrochemical performance. These enhancements in performance were studied using TEM, SEM, in-situ-XRD, XPS, CV, EIS and post-mortem analyses. This synthetic method enables the highly scalable production of CG-NCMA samples with two concentration-gradient structures for practical applications in Li-ion batteries.
Mesoporous silica nanoparticles (MSNs) were synthesized with variable microwave power in the range of 100-450 W, and the resulting enhancement of MSN crystal growth was evaluated for the adsorption and release of ibuprofen. X-ray diffraction (XRD) revealed that the MSN prepared under the highest microwave power (MSN450) produced the most crystallized and prominent mesoporous structure. Enhancement of the crystal growth improved the hexagonal order and range of silica, which led to greater surface area, pore width and pore volume. MSN450 exhibited higher ibuprofen adsorption (98.3 mg/g), followed by MSN300(81.3 mg/g) and MSN100(74.1 mg/g), confirming that more crystallized MSN demonstrated higher adsorptivity toward ibuprofen. Significantly, MSN450 also contained more hydroxyl groups that provided more adsorption sites. In addition, MSN450 exhibited comparable ibuprofen adsorption with conventionally synthesized MSN, indicating the potential of microwave treatment in the synthesis of related porous materials. In vitro drug release was also investigated with simulated biological fluids and the kinetics was studied under different pH conditions. MSN450 showed the slowest release rate of ibuprofen, followed by MSN300 and MSN100. This was due to the wide pore diameter and longer range of silica order of the MSN450. Ibuprofen release from MSN450 at pH 5 and 7 was found to obey a zero-order kinetic model, while release at pH 2 followed the Kosmeyer-Peppas model.
Carbon nanotubes-mesostructured silica nanoparticles (CNT-MSN) composites were prepared by a simple one step method with various loading of CNT. Their surface properties were characterized by XRD, N2 physisorption, TEM and FTIR, while the adsorption performance of the CNT-MSN composites were evaluated on the adsorption of methylene blue (MB) while varying the pH, adsorbent dosage, initial MB concentration, and temperature. The CNTs were found to improve the physicochemical properties of the MSN and led to an enhanced adsorptivity for MB. N2 physisorption measurements revealed the development of a bimodal pore structure that increased the pore size, pore volume and surface area. Accordingly, 0.05 g L(-1) CNT-MSN was able to adsorb 524 mg g(-1) (qm) of 60 mg L(-1) MB at pH 8 and 303 K. The equilibrium data were evaluated using the Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich isotherm models, with the Langmuir model affording the best fit to the adsorption data. The adsorption kinetics were best described by the pseudo-first order model. These results indicate the potential of CNT-MSN composites as effective new adsorbents for dye adsorption.
In this work, mesostructured silica nanoparticles (MSN(AP)) with high adsorptivity were prepared by a modification with 3-aminopropyl triethoxysilane (APTES) as a pore expander. The performance of the MSN(AP) was tested by the adsorption of MB in a batch system under varying pH (2-11), adsorbent dosage (0.1-0.5 g L(-1)), and initial MB concentration (5-60 mg L(-1)). The best conditions were achieved at pH 7 when using 0.1 g L(-1) MSN(AP) and 60 mg L(-1)MB to give a maximum monolayer adsorption capacity of 500.1 mg g(-1) at 303 K. The equilibrium data were evaluated using the Langmuir, Freundlich, Temkin, and Harkins-Jura isotherms and fit well to the Freundlich isotherm model. The adsorption kinetics was best described by the pseudo-second order model. The results indicate the potential for a new use of mesostructured materials as an effective adsorbent for MB.
The inhibitory effect of two Schiff bases 3-(5-methoxy-2-hydroxybenzylideneamino)-2-(-5-methoxy-2-hydroxyphenyl)-2,3-dihydroquinazoline-4(1H)-one (MMDQ), and 3-(5-nitro-2-hydroxybenzylideneamino)-2(5-nitro-2-hydroxyphenyl)-2,3-dihydroquinazoline-4(1H)-one (NNDQ) on the corrosion of mild steel in 1M hydrochloric acid were studied using mass loss, potentiodynamic polarization technique and electrochemical impedance spectroscopy measurements at ambient temperature. The investigation results indicate that the Schiff Bases compounds with an average efficiency of 92% at 1.0mM of additive concentration have fairly effective inhibiting properties for mild steel in hydrochloric acid, and acts as mixed type inhibitor character. The inhibition efficiencies measured by all measurements show that the inhibition efficiencies increase with increase in inhibitor concentration. This reveals that the inhibitive mechanism of inhibitors were primarily due to adsorption on mild steel surface, and follow Langmuir adsorption isotherm. The temperature effect on the inhibition process in 1MHCl with the addition of investigated Schiff bases was studied at a temperature range of 30-60°C, and the activation parameters (Ea, ΔH and ΔS) were calculated to elaborate the corrosion mechanism. The differences in efficiency for two investigated inhibitors are associated with their chemical structures.
Pseudo-first-order rate constants (k(obs)) for alkaline hydrolysis of 4-nitrophthalimide show a monotonic decrease with increase in [C(12)E(23)](T) (total concentration of Brij 35) at constant [CH(3)CN] and [NaOH]. This micellar effect is explained in terms of a pseudophase micelle model. The rate of hydrolysis becomes too slow to monitor at [C(12)E(23)](T)>/=0.03 M in the absence of cetyltrimethylammonium bromide (CTABr) and at [C(12)E(23)](T)>/=0.04 M in the presence of 0.006-0.02 M CTABr at 0.01 M NaOH. The plots of k(obs) versus [C(12)E(23)](T) show minima at 0.006 and 0.01 M CTABr, while such a minimum is not visible at 0.02 M CTABr. Copyright 2001 Academic Press.
The effects of Brij 35 micelles, CTABr micelles, and mixed Brij 35-CTABr micelles on the acid-base behavior of phenyl salicylate (PST) have been studied in aqueous solution containing 2% v/v acetonitrile. The apparent pK(b) (pK(app)(b)) of PST is decreased by 1.5 pK units with the increase in [Brij 35] from 0 to 0.02 M which is attributed to micellar medium effect. The values of pK(app)(b) remain almost independent of [CTABr] within its range 0.01-0.03 M. The increase in [CTABr] from 0 to 0.03 M in aqueous solution containing 0.02 M Brij 35 has not resulted in a change in pK(app)(b). This shows that the characeristic structural features of nonionic Brij 35 micelles remain essentially unchanged on addition of CTABr under the present experimental conditions. Copyright 1999 Academic Press.
Highly effective WO3/ZnO nanorods (NRs) were synthesized via a hydrothermal-deposition method for degradation of 2,4-dichlorophenoxyacetic acid (2,4-D) under natural sunlight. The structural properties of WO3/ZnO NRs such as morphology, crystal structure, porous properties and light absorption characteristics were investigated in detail. The X-ray diffraction and X-ray photoelectron spectroscopy results indicated that the prepared samples were two-phase photocatalysts consisted of WO3 and ZnO NRs. The UV-vis diffuse reflectance spectroscopy result showed that the addition of WO3 altered the optical properties of the photocatalysts. In contrast with the pure ZnO NRs, commercial anatase TiO2 and commercial WO3, the WO3/ZnO NRs showed excellent sunlight photocatalytic activities in degrading 2,4-D. The optimal WO3 loading and calcination temperature were also determined. Based on the band position, the synergetic effect of WO3 and ZnO NRs was the source of the enhanced photocatalytic activity as validated by PL and terephthalic acid-photoluminescence measurements. The reaction intermediates and degradation pathways of 2,4-D were elucidated by a HPLC method. In addition, the extent of mineralization during the 2,4-D degradation was also estimated using total organic carbon (TOC) and ion chromatography (IC) analyses.
A liquid crystal physical gel was prepared by the self-assembly of cholesteryl stearate in a nematic liquid crystal, 4-cyano-4'-pentylbiphenyl. The electro-optical properties were tuned by varying the gelator concentration and the gelation conditions. Polarized optical microscopy revealed that cholesteric cholesteryl stearate induced chiral nematic phase in 4-cyano-4'-pentylbiphenyl during the gelation process. As a result, a plate-like gel structure consisting of spherical micropores was formed, as observed by scanning electron microscopy. Electron spin resonance spectroscopy showed that the liquid crystal director orientations in these macrophase-separated structures were massively randomised. For these reasons, the liquid crystal physical gel generated a strong light scattering effect. For 48.0wt% cholesteryl stearate gelled 4-cyano-4'-pentylbiphenyl, the turbid appearance could be switched to a transparent state using a 5.0V alternating current. The response time was about 3.7μs. This liquid crystal physical gel has potential for use in light scattering electro-optical displays.
DNA-templated silver nanoclusters (AgNC) are a class of subnanometer sized fluorophores with good photostability and brightness. It has been applied as a diagnostic tool mainly for deoxyribonucleic acid (DNA) detection. Integration of DNA oligomers to generate AgNCs is interesting as varying DNA sequences can result in different fluorescence spectra. This allows a simple fluorescence shifting effect to occur upon DNA hybridization with the hybridization efficiency being a pronominal factor for successful shifting. The ability to shift the fluorescence spectra as a result of hybridization overcomes the issue of background intensities in most fluorescent based assays. Here we describe an optimized method for the detection of single-stranded and double-stranded synthetic forkhead box P3 (FOXP3) target by hybridization with the DNA fluorescence shift sensor. The system forms a three-way junction by successful hybridization of AgNC, G-rich strand (G-rich) to the target DNA, which generated a shift in fluorescence spectra with a marked increase in fluorescence intensity. The DNA fluorescence shift sensor presents a rapid and specific alternative to conventional DNA detection.
Magnetophoresis of iron oxide magnetic nanoparticle (IOMNP) under low magnetic field gradient (<100 T/m) is significantly enhanced by particle shape anisotropy. This unique feature of magnetophoresis is influenced by the particle concentration and applied magnetic field gradient. By comparing the nanosphere and nanorod magnetophoresis at different concentration, we revealed the ability for these two species of particles to achieve the same separation rate by adjusting the field gradient. Under cooperative magnetophoresis, the nanorods would first go through self- and magnetic field induced aggregation followed by the alignment of the particle clusters formed with magnetic field. Time scale associated to these two processes is investigated to understand the kinetic behavior of nanorod separation under low field gradient. Surface functionalization of nanoparticles can be employed as an effective strategy to vary the temporal evolution of these two aggregation processes which subsequently influence the magnetophoretic separation time and rate.
The rate of autooxidation of 3,5-di-tert-butylcatechol (3,5-DTBC) in the presence of micelles formed from mixing equal concentrations of [Cu(C(12)-tmed)Br(2)] (where C(12)-tmed is N,N,N'-trimethyl-N'-dodecylethylenediamine) and several amino acids has been investigated. It was found that the rate in air-saturated solution is very much dependent on pH, which affects the availability of copper(II) coordination site for the catechol and the degree of micellization. At a given pH, the rates in [Cu(C(12)-tmed)Br(2)] micellar media are greatly enhanced in the presence sodium halide.
Micellar properties of binary mixed surfactants of a surface active mixed copper(II) chelate, [Cu(C12-tmed)(acac)Cl] (where C12-tmed is N,N,N'-trimethyl-N'-dodecylethylenediamine) with three common surfactants, viz. sodium dodecyl sulfate (SDS), cetyltrimethylammonium bromide (CTAB), and octaethylene glycol monododecyl ether (C12E8), were investigated by surface tensiometry, ESR, and UV-visible absorption techniques. The surface tension data were treated with Rubingh's method for mixed micelle formation and Rosen's method for mixed monolayer formation at the aqueous solution/air interface. It was found that in the mixed micelle there is strong attractive interaction between cationic copper surfactant and anonic dodecyl sulfate while there is almost ideal mixing between copper surfactant and CTAB and C12E8. From the ESR and UV-visible studies, a mixed block-type arrangement of head groups is proposed. Copyright 1997 Academic Press. Copyright 1997Academic Press
Metal Organic Frameworks (MOFs) represent a promising class of metallic catalysts for reduction of nitrogen-containing contaminants (NCCs), such as 4-nitrophenol (4-NP). Nevertheless, most researches involving MOFs for 4-NP reduction employ noble metals in the form of fine powders, making these powdered noble metal-based MOFs impractical and inconvenient for realistic applications. Thus, it would be critical to develop non-noble-metal MOFs which can be incorporated into macroscale and porous supports for convenient applications. Herein, the present study proposes to develop a composite material which combines advantageous features of macroscale/porous supports, and nanoscale functionality of MOFs. In particular, copper foam (CF) is selected as a macroscale porous medium, which is covered by nanoflower-structured CoO to increase surfaces for growing a cobaltic MOF, ZIF-67. The resultant composite comprises of CF covered by CoO nanoflowers decorated with ZIF-67 to form a hierarchical 3D-structured catalyst, enabling this ZIF-67@Cu foam (ZIF@CF) a promising catalyst for reducing 4-NP, and other NCCs. Thus, ZIF@CF can readily reduce 4-NP to 4-AP with a significantly lower Ea of 20 kJ/mol than reported values. ZIF@CF could be reused over 10 cycles and remain highly effective for 4-NP reduction. ZIF@CF also efficiently reduces other NCCs, such as 2-nitrophenol, 3-nitrophenol, methylene blue, and methyl orange. ZIF@CF can be adopted as catalytic filters to enable filtration-type reduction of NCCs by passing NCC solutions through ZIF@CF to promptly and conveniently reduce NCCs. The versatile and advantageous catalytic activity of ZIF@CF validates that ZIF@CF is a promising and practical heterogeneous catalyst for reductive treatments of NCCs.
Aerobic oxidation of 5-Hydroxymethylfurfural (HMF) to 2,5-Diformylfuran (DFF) using O2 gas represents a sustainable approach for valorization of lignocellulosic compounds. As manganese dioxide (MnO2) is validated as a useful oxidation catalyst and many crystalline forms of MnO2 exist, it is critical to explore how the crystalline structures of MnO2 influence their physical/chemical properties, which, in turn, determine catalytic activities of MnO2 crystals for HMF oxidation to DFF. In particular, six MnO2 crystals, α-MnO2, β-MnO2, γ-MnO2, δ-MnO2, ε-MnO2, and λ-MnO2 are prepared and investigated for their catalytic activities for HMF oxidation to DFF. With different morphologies and crystalline structures, these MnO2 crystals possess very distinct surficial chemistry, redox capabilities, and textural properties, making these MnO2 exhibit different catalytic activities towards HMF conversion. Especially, β-MnO2 can produce much higher DFF per surface area than other MnO2 crystals. β-MnO2 could achieve the highest CHMF = 99% and YDFF = 97%, which are much higher than the reported values in literature, possibly because the surficial reactivity of β-MnO2 appears to be highest in comparison to other MnO2 crystals. Especially, β-MnO2 could exhibit YDFF > 90% over 5 cycles of reusability test, and maintain its crystalline structure, revealing its advantageous feature for aerobic oxidation of HMF to DFF. Through this study, the relationship between morphology, surface chemistry, and catalytic activity of MnO2 with different crystal forms is elucidated for providing scientific insights into design, application and development of MnO2-based materials for aerobic oxidation of bio-derived molecules to value-added products.