The presence of pores plays an important role for many membrane processes especially in ultrafiltration and microfiltration. Epoxidised natural rubber (ENR)/polyvinyl chloride (PVC) membranes filled with two types of silica fillers were prepared via simultaneous solvent exchange and evaporation of solvent technique. Two types of silica, i.e. microsilica (microcrystalline
silica powder) and nanosilica (generated from tetraethoxysilane (TEOS)) were used. The chemical composition, morphology and mechanical stability of the membranes were studied. Both types of silica showed good interaction with the membrane matrix. The formation of pores depended on the size of silica particles added. Microsilica produced large pores while insitu generated nanosilica produced nanosized pores. The mechanical properties of membrane improved with the addition
of silica. The tensile strength increased from 10.6 MPa to 17.8 MPa and 14.5 MPa for nanosilica and microsilica filled membrane while the tensile modulus increased from 1.6 MPa to 3.8 MPa and 3.4 MPa, respectively. Thus, both types of silica acted as a filler as well as pore forming agent for the ENR/PVC membrane.
Some basic requirements are set for small clear specimen data to incorporate Malaysian timbers into equivalent European timber strength classes. In general, the correlation between structural and small clear specimen test results must be established for every timber group regardless of origin. This paper introduces a sort-plot technique for analysing the correlation of some mechanical properties of timber in selecting appropriate parametric model. Bending test was conducted on mixed species hardwoods for the determination of strength and stiffness values of both structural and small size specimens. The results showed that the sort-plot diagrams demonstrate an obvious linearity pattern between timber properties despite having poor regression values. The technique verified that properties of timber in structural and small size specimens correlated linearly.
Nata de coco or bacterial cellulose produced by Acetobacter xylinum is a unique type of biocellulose. It contains more than 90% of water. Dried nata was preferred compared to wet form since it is more convenient and portable with stable properties. Therefore, drying process is necessary in order to produce dried nata de coco. Drying method is a key factor that influenced the properties of dried nata de coco produced. The aim of this study was to investigate the effect of different drying methods on morphology, crystallinity, swelling ability and tensile strength of dried nata de coco. Nata de coco samples were dried using three physical drying methods such as oven, tray dryer or freeze dryer until it achieved 3-5% moisture content. Obviously, the three drying techniques produced web-like structured nata de coco and quite similar crystallinity which was in range between 87 and 89%. Freeze dried sample showed the largest swelling capacity and tensile strength which was found to be 148 MPa. Different drying method gave different properties of nata de coco. Therefore, the present work proposed the most suitable drying method can be utilized based on the properties of end product needed.
Epoxidized natural rubber (ENR-50) has been used as a compatibilizer for natural rubber-recycled acrylonitrile-butadiene
rubber (NR/NBRr) blends, vulcanized by sulfur. NBR gloves have excellent resistance to punctures, tear and many types
of chemicals, while NR has good physical and mechanical properties. Incorporation of ENR-50 into the rubber blends
has improved processability, stiffness, resilience and excellent oil resistance. NR/NBRr blends were prepared by two-roll
mill with five different compositions with the ENR-50 content fixed at 10 phr. Cure characteristics, mechanical properties
and morphology (SEM) studies were performed to determine the compatibility of NR/NBRr blends in the presence of ENR-
50. The cure characteristics showed that NR/NBRr blends with the presence of ENR-50 have lower scorch time (ts2) and
cure time (t90) than NR/NBRr blends without ENR-50. However, the NR/NBRr blends with ENR-50 exhibited higher minimum
torque (ML
) and maximum torque (MH) which indicated difficult processability of the blends after compatibilization.
Incorporation of ENR-50 into NR/NBRr blends improved all the tensile properties (tensile strength, tensile modulus and
elongation at break) compared with NR/NBRr blends without ENR-50. The improvement in hardness upon compatibilization
is due to an increase in crosslink density. Scanning electron microscopy (SEM images) of the fracture surfaces indicates
that, with the addition of ENR-50 in NR/NBRr blends, better adhesion between NR and NBRr was obtained, thus improving
the compatibility of NR/NBRr blends.
Polylactic acid (PLA)/Epoxidized natural rubber (ENR-50) blends were prepared by melt extrusion followed by injection
molding to fabricate the test samples. The effect of ENR-50 loadings on the morphological, mechanical, chemical
resistance and water absorption properties of the blends were studied using standard methods. The toughness of the
blend improved with ENR loading up to 20 wt. % but flexural and tensile strength decreased. The balanced mechanical
properties were obtained at 20 wt. % ENR-50 loading. SEM showed good distribution and increased ENR particle size
as ENR content increased from 10 to 30 wt. %. The differential scanning calorimeter (DSC) showed a steady drop in
crystallization temperature (Tc
) as ENR content increases while the glass transition temperature (Tg
) remained unchanged.
Water absorption was observed to increase with ENR loadings. Increase in ENR content was also observed to reduce the
chemical resistance of the blends.
Cellulose nanocrystals (CNC) from mengkuang leaves (Pandanus tectorius) were investigated as potential reinforcement
in poly(vinyl chloride) (PVC) matrix. The surface of CNC was modified with silane coupling agent to improve fillermatrix
adhesion. Solution casting method was used to prepare PVC nanocomposites with various amounts of modified
(SCNC) and unmodified (CNC) nanocrystals. Both SCNC and CNC were examined by Fourier transform infrared (FTIR)
spectroscopy and X-ray diffraction (XRD) which showed that surface chemical modification has occurred. An increase
in tensile strength was observed with the addition of SCNC compared to the CNC. However, the elongation at break of the
nanocomposites was found to decrease with the increase of both fillers loading. An increasing trend was observed in the
tensile modulus with the addition of CNC to the PVC matrix, but decreasing with the addition of SCNC. The morphology
of a fractured surface of nanocomposites showed silane modification reduced the number of voids in the structure of
PVC. The observation indicated the adhesion between the fiber and the matrix had improved upon surface modification
of the nanocrystals with silane.
The effects of HVA-2 on radiation-induced cross-linkings in 60/40 natural rubber/ linear low density polyethylene (NR/LLDPE) blends was studied. NR/LLDPE was irradiated by using a 3.0 MeV electron beam machine with doses ranging from 0 to 250 kGy. Results showed that under the irradiation employed, the blends NR/LLDPE were cross-linked by the electron beam irradiation. The presence of HVA-2 in the blends caused the optimum dose to decrease and the blends to exhibit higher tensile properties. Further, within the dose range studied, the degradation caused by electron beam irradiation was found to be minimal. The optimized processing conditions were 120oC, 50 rpm rotor speed and 13 min processing time. The gel content, tensile strength, elongation at break, hardness and impact test studies were used to follow the irradiation-induced cross-linkings in the blend. For blends of 60/40 NR/LLDPE with 2.0 phr HVA-2, the optimum tensile strength and dose, were 19 MPa and 100 kGy, respectively. Blends of 60/40 NR/LLDPE without HVA-2, the optimum tensile strength and dose were 17.2 MPa and 200 kGy, respectively.
Several methods of incorporating sago pith waste (SPW) into poly(vinyl alcohol) (PVA) had been conducted: (i) dry blending (PVA/SPW/G), (ii) blending of SPW and pre-plasticized PVA (pPVA/SPW/G) and (iii) blending of pre-plasticized of both PVA and SPW (pPVA/pSPW). The effect of the compounding method on the mechanical and water absorption properties were investigated. The addition of SPW into PVA greatly reduced the tensile strength and elongation at break. The tensile strength and elongation at break of PVA/SPW composites with identical geometry during compounding stage (powder/powder and pellet/pellet), which were PVA/SPW/G and pPVA/pSPW yielded the highest value. The percentage of water absorbed by PVA/SPW/G (without pre-plasticization) was the highest, followed by pPVA/pSPW and pPVA/SPW/G.
There has been an increasing interest in the use of natural materials as drug delivery vehicles due to their biodegradability, biocompatibility and ready availability. These properties make bacterial cellulose (BC), from nata de coco, a promising biopolymer for drug delivery applications. The aim of this study was to investigate the film-coating and drug release properties of this biopolymer. Physicochemical, morphological and thermal properties of BC films were studied. Model tablets were film coated with BC, using a spray coating technique, and in vitro drug release studies of these tablets were investigated. It was found that BC exhibited excellent ability to form soft, flexible and foldable films without the addition
of any plasticizer. They were comparable to Aquacoat ECD (with plasticizer) in tensile strength, percentage elongation and elasticity modulus. Differential scanning calorimetry (DSC) BC showed a high Tg value indicating thermally stability of films. These results suggest that BC can be used as novel aqueous film-coating agent with lower cost and better film forming properties than existing film-coating agents.
Hybrid composites of polypropylene (PP)/nanoclay (NC)/glass fiber (GF) were prepared byextrusion and injection molding. Molded specimens were analyzed by transmission electron microscopy (TEM), thermogravimetric analysis (TGA), tensile and flexural tests. TEM results revealed NC particle intercalation. TGA results showed that the incorporation of clay into the GF composite improves the thermal stability of the material. The initial thermal decomposition temperatures also shifted to higher values. Incorporation of GF into PP lowers the tensile strength of the binary composite, indicating poor fiber-matrix interfacial adhesion. However, introducing NC increased the strength of the ternary composites. Tensile modulus was enhanced with the incorporation of GF and further increased with an introduction of NC. Flexural strength and flexural modulus are both enhanced with an increase in GF and NC loading.
316L stainless steel is a common biomedical material. Currently, biomedical parts are produced through powder injection molding (PIM). Carbon control is the most critical in PIM. Improper debinding can significantly change the properties of the final product. In this work, thermal debinding and sintering were performed in two different furnaces (i.e. laboratory and commercially available furnaces) to study the mechanical properties and corrosion resistance. Debounded samples were sintered in different atmospheres. The samples sintered in inert gas showed enhanced mechanical properties compared with wrought 316L stainless steel and higher corrosion rate than those sintered in the vacuum furnace. The densification and tensile strength of the hydrogen sintered samples increased up to 3% and 51%, respectively, compared with those of the vacuum-sintered samples. However, the samples sintered in inert gas also exhibited reduced ductility and corrosion resistance. This finding is attributed to the presence of residual carbon in debonded samples during debinding.
The tensile strength of intact rock materials has been determined by indirect method more frequent than the direct method.
The most commonly used indirect method is Brazilian test. Stress and deformability undergo during the test reflected by
geometry shape of the samples with respect to the different diameter ratio. This study focuses on influence of geometry
shape in solid and ring disk with different diameter ratio on the stress distribution and deformations within sandstone
subjected to indirect tensile loading by Brazilian test. Then, the finite element method in RS2 software was utilised to
simulate and gain in depth understanding the behaviour of Brazilian test. The analysis shown that the maximum tensile
strength in a ring disk with diameter ratio of 0.1 is three times higher than in solid disk. Meanwhile, as the diameter
ratio of ring disk increases, it produces lower tensile strength. The numerical simulation also has successfully illustrated
the shear failure which observed near the loading platen of solid disk during Brazilian test. The finite element analysis
utilised in this research has successfully enables the stress distribution and deformation behaviour of the rock under
tension to be studied closely
The aim of this paper was to describe the effects of treated sugar palm yarn fibre loading on the mechanical properties
of reinforced unsaturated polyester composites. Composites with varying fibre loads (10, 20, 30, 40 and 50 wt. %) were
prepared using a hand-layup process. The composites were tested for tensile, flexural and impact strength according to
ASTM D3930, ASTM D790 and ASTM D256 standards, respectively. The results showed that an increase in fibre loading
of up to 30 wt. % increased tensile strength (31.27 MPa), tensile modulus (4.83 GPa), flexural strength (58.14 MPa)
and modulus (4.48 GPa). Maximum loading can be attained at 40 wt. % of fibre loading for impact strength (38 kJ/
m2). The effectiveness of stress transfer mechanism through the fibre-matrix interaction, coupled with the optimization
of fibre loading in resisting fracture and failure, boosts the overall mechanical performance of sugar palm composite.
This research was carried out to study the effects of kenaf loading and alkaline treatment on tensile properties, density,
thermal and morphological properties of kenaf filled natural rubber latex foam (NRLF). Samples were prepared using a
Dunlop method. From the results, increasing loading of kenaf reduced the tensile strength and elongation at break for
both samples, treated and untreated kenaf filled NRLF. Meanwhile, modulus at 100% elongation and density increased
with an increased in kenaf loading. Samples with treated kenaf showed higher tensile strength, modulus at 100%
elongation and density but low in elongation at break as compared with samples with untreated kenaf. Thermal study
by using thermogravimetric analysis (TGA) showed that thermal stability reduced with increased in kenaf loading for
both samples. Samples with treated kenaf have higher thermal stability compared with samples of untreated kenaf. The
filler-matrix interaction and the pores size variation of both samples was clearly seen in the micrograph images by using
scanning electron microscope (SEM).
This study aimed to develop a three-dimensional finite element model of a functionally graded femoral prosthesis. The model consisted of a femoral prosthesis created from functionally graded materials (FGMs), cement, and femur. The hip prosthesis was composed of FGMs made of titanium alloy, chrome-cobalt, and hydroxyapatite at volume fraction gradient exponents of 0, 1, and 5, respectively. The stress was measured on the femoral prosthesis, cement, and femur. Stress on the neck of the femoral prosthesis was not sensitive to the properties of the constituent material. However, stress on the stem and cement decreased proportionally as the volume fraction gradient exponent of the FGM increased. Meanwhile, stress became uniform on the cement mantle layer. In addition, stress on the femur in the proximal part increased and a high surface area of the femoral part was involved in absorbing the stress. As such, the stress-shielding area decreased. The results obtained in this study are significant in the design and longevity of new prosthetic devices because FGMs offer the potential to achieve stress distribution that more closely resembles that of the natural bone in the femur.
This work represents a study to investigate the mechanical properties of longitudinal basalt/woven-glass-fiber-reinforced unsaturated polyester-resin hybrid composites. The hybridization of basalt and glass fiber enhanced the mechanical properties of hybrid composites. The unsaturated polyester resin (UP), basalt (B) and glass fibers (GF) were fabricated using the hand lay-up method in six formulations (UP, GF, B7.5/G22.5, B15/G15, B22.5/G7.5 and B) to produce the composites, respectively. This study showed that the addition of basalt to glass-fiber-reinforced unsaturated polyester resin increased its density, tensile and flexural properties. The tensile strength of the B22.5/G7.5 hybrid composites increased by 213.92 MPa compared to neat UP, which was 8.14 MPa. Scanning electron microscopy analysis was used to observe the fracture mode and fiber pullout of the hybrid composites.
In this paper, sugar palm nanocellulose fibre-reinforced thermoplastic starch (TPS)/poly (lactic acid) (PLA) blend bionanocomposites were prepared using melt blending and compression moulding with different TPS concentrations (20%, 30%, 40%, 60%, and 80%) and constant sugar palm nanocellulose fibres (0.5%). The physical, mechanical, thermal, and water barrier properties were investigated. The SEM images indicated different TPS loading effects with the morphology of the blend bionanocomposites due to their immiscibility. A high content of TPS led to agglomeration, while a lower content resulted in the presence of cracks and voids. The 20% TPS loading reduced the tensile strength from 49.08 to 19.45 MPa and flexural strength from 79.60 to 35.38 MPa. The thermal stability of the blend bionanocomposites was reduced as the TPS loading increased. The thickness swelling, which corresponded to the water absorption, demonstrated an increasing trend with the increased addition of TPS loading.
This study examined the development of starch/oil palm empty fruit bunch-based bioplastic composites reinforced with either epoxidized palm oil (EPO) or epoxidized soybean oil (ESO), at various concentrations, in order to improve the mechanical and water-resistance properties of the bio-composites. The SEM micrographs showed that low content (0.75 wt%) of epoxidized oils (EOs), especially ESO, improved the compatibility of the composites, while high content (3 wt%) of EO induced many voids. The melting temperature of the composites was increased by the incorporation of both EOs. Thermal stability of the bioplastics was increased by the introduction of ESO. Low contents of EO led to a huge enhancement of tensile strength, while higher contents of EO showed a negative effect, due to the phase separation. The tensile strength increased from 0.83 MPa of the control sample to 3.92 and 5.42 MPa for the composites with 1.5 wt% EPO and 0.75 wt% ESO, respectively. EOs reduced the composites' water uptake and solubility but increased the water vapor permeability. Overall, the reinforcing effect of ESO was better than EPO. These results suggested that both EOs can be utilized as modifiers to prepare starch/empty-fruit-bunch-based bioplastic composites with enhanced properties.
The mechanical behavior of graphene/polymer interfaces in the graphene-reinforced epoxy nanocomposite is one of the factors that dictates the deformation and damage response of the nanocomposites. In this study, hybrid molecular dynamic (MD) and finite element (FE) simulations of a graphene/polymer nanocomposite are developed to characterize the elastic-damage behavior of graphene/polymer interfaces under a tensile separation condition. The MD results show that the graphene/epoxy interface behaves in the form of elastic-softening exponential regressive law. The FE results verify the adequacy of the cohesive zone model in accurate prediction of the interface damage behavior. The graphene/epoxy cohesive interface is characterized by normal stiffness, tensile strength, and fracture energy of 5 × 10-8 (aPa·nm-1), 9.75 × 10-10 (nm), 2.1 × 10-10 (N·nm-1) respectively, that is followed by an exponential regressive law with the exponent, α = 7.74. It is shown that the commonly assumed bilinear softening law of the cohesive interface could lead up to 55% error in the predicted separation of the interface.
In this study, lignin has been extracted from oil palm empty fruit bunch (EFB) fibers via an organosolv process. The organosolv lignin obtained was defined by the presence of hydroxyl-containing molecules, such as guaiacyl and syringyl, and by the presence of phenolic molecules in lignin. Subsequently, the extracted organosolv lignin and graphene nanoplatelets (GNP) were utilized as filler and reinforcement in photo-curable polyurethane (PU), which is used in stereolithography 3D printing. The compatibility as well as the characteristic and structural changes of the composite were identified through the mechanical properties of the 3D-printed composites. Furthermore, the tensile strength of the composited lignin and graphene shows significant improvement as high as 27%. The hardness of the photo-curable PU composites measured by nanoindentation exhibited an enormous improvement for 0.6% of lignin-graphene at 92.49 MPa with 238% increment when compared with unmodified PU.