We report the seed/catalyst-free growth of ZnO on multilayer graphene by thermal evaporation of Zn in the presence of O2 gas. The effects of substrate temperatures were studied. The changes of morphologies were very significant where the grown ZnO structures show three different structures, i.e., nanoclusters, nanorods, and thin films at 600°C, 800°C, and 1,000°C, respectively. High-density vertically aligned ZnO nanorods comparable to other methods were obtained. A growth mechanism was proposed based on the obtained results. The ZnO/graphene hybrid structure provides several potential applications in electronics and optoelectronics.
We demonstrate a systematic computational analysis of the measured optical and charge transport properties of the spray pyrolysis-grown ZnO nanostructures, i.e. nanosphere clusters (NSCs), nanorods (NRs) and nanowires (NWs) for the first time. The calculated absorbance spectra based on the time-dependent density functional theory (TD-DFT) shows very close similarity with the measured behaviours under UV light. The atomic models and energy level diagrams for the grown nanostructures were developed and discussed to explain the structural defects and band gap. The induced stresses in the lattices of ZnO NSCs that formed during the pyrolysis process seem to cause the narrowing of the gap between the energy levels. ZnO NWs and NRs show homogeneous distribution of the LUMO and HOMO orbitals all over the entire heterostructure. Such distribution contributes to the reduction of the band gap down to 2.8 eV, which has been confirmed to be in a good agreement with the experimental results. ZnO NWs and NRs exhibited better emission behaviours under the UV excitation as compared to ZnO NSCs and thin film as their visible range emissions are strongly quenched. Based on the electrochemical impedance measurement, the electrical models and electrostatic potential maps were developed to calculate the electron lifetime and to explain the mobility or diffusion behaviours in the grown nanostructure, respectively.
We report the growth of gallium-based compounds, i.e., gallium oxynitride (GaON) and gallium oxide (Ga2O3) on multilayer graphene (MLG) on insulator using a mixture of ammonium nitrate (NH4NO3) and gallium nitrate (Ga(NO3)3) by electrochemical deposition (ECD) method at room temperature (RT) for the first time. The controlling parameters of current density and electrolyte molarity were found to greatly influence the properties of the grown structures. The thicknesses of the deposited structures increase with the current density since it increases the chemical reaction rates. The layers grown at low molarities of both solutions basically show grain-like layer with cracking structures and dominated by both Ga2O3 and GaON. Such cracking structures seem to diminish with the increases of molarities of one of the solutions. It is speculated that the increase of current density and ions in the solutions helps to promote the growth at the area with uneven thicknesses of graphene. When the molarity of Ga(NO3)3 is increased while keeping the molarity of NH4NO3 at the lowest value of 2.5 M, the grown structures are basically dominated by the Ga2O3 structure. On the other hand, when the molarity of NH4NO3 is increased while keeping the molarity of Ga(NO3)3 at the lowest value of 0.8 M, the GaON structure seems to dominate where their cubic and hexagonal arrangements are coexisting. It was found that when the molarities of Ga(NO3)3 are at the high level of 7.5 M, the grown structures tend to be dominated by Ga2O3 even though the molarity of NH4NO3 is made equal or higher than the molarity of Ga(NO3)3. When the grown structure is dominated by the Ga2O3 structure, the deposition process became slow or unstable, resulting to the formation of thin layer. When the molarity of Ga(NO3)3 is increased to 15 M, the nanocluster-like structures were formed instead of continuous thin film structure. This study seems to successfully provide the conditions in growing either GaON-dominated or Ga2O3-dominated structure by a simple and low-cost ECD. The next possible routes to convert the grown GaON-dominated structure to either single-crystalline GaN or Ga2O3 as well as Ga2O3-dominated structure to single-crystalline Ga2O3 structure have been discussed.
The dissociation of zinc ions (Zn(2+)) from vapor-phase zinc acetylacetonate, Zn(C5H7O2)2, or Zn(acac)2 and its adsorption onto graphene oxide via atomic layer deposition (ALD) were studied using a quantum mechanics approach. Density functional theory (DFT) was used to obtain an approximate solution to the Schrödinger equation. The graphene oxide cluster model was used to represent the surface of the graphene film after pre-oxidation. In this study, the geometries of reactants, transition states, and products were optimized using the B3LYB/6-31G** level of theory or higher. Furthermore, the relative energies of the various intermediates and products in the gas-phase radical mechanism were calculated at the B3LYP/6-311++G** and MP2/6-311 + G(2df,2p) levels of theory. Additionally, a molecular orbital (MO) analysis was performed for the products of the decomposition of the Zn(acac)2 complex to investigate the dissociation of Zn(2+) and the subsequent adsorption of H atoms on the C5H7O2 cluster to form acetylacetonate enol. The reaction energies were calculated, and the reaction mechanism was accordingly proposed. A simulation of infrared (IR) properties was performed using the same approach to support the proposed mechanism via a complete explanation of bond forming and breaking during each reaction step.
A seed/catalyst-free growth of ZnO on graphene by thermal evaporation of Zn in the presence of O2 gas was further studied. The effects of substrate positions and graphene thicknesses on the morphological, structural, and optical properties were found to be very pronounced. By setting the substrate to be inclined at 90°, the growth of ZnO nanostructures, namely, nanoclusters and nanorods, on single-layer (SL) graphene was successfully realized at temperatures of 600°C and 800°C, respectively. For the growth on multilayer (ML) graphene at 600°C with an inclination angle of 90°, the grown structures show extremely thick and continuous cluster structures as compared to the growth with substrate's inclination angle of 45°. Moreover, the base of nanorod structures grown at 800°C with an inclination angle of 90° also become thicker as compared to 45°, even though their densities and aspect ratios were almost unchanged. Photoluminescence (PL) spectra of the grown ZnO structures were composed of the UV emission (378-386 nm) and the visible emission (517-550 nm), and the intensity ratio of the former emission (I UV) to the latter emission (I VIS) changed, depending on the temperature. The structures grown at a low temperature of 600°C show the highest value of I UV/I VIS of 16.2, which is almost two times higher than the structures grown on SL graphene, indicating fewer structural defects. The possible growth mechanism was proposed and described which considered both the nucleation and oxidation processes. From the results obtained, it can be concluded that temperature below 800°C, substrate position inclined at 90° towards the gas flow, and ML graphene seems to be preferable parameters for the growth of ZnO structures by thermal evaporation because these factors can be used to overcome the problem of graphene's oxidation that takes place during the growth.
Hydrothermal zinc oxide (ZnO) thick films were successfully grown on the chemical vapor deposition (CVD)-grown thick ZnO seed layers on a-plane sapphire substrates using the aqueous solution of zinc nitrate dehydrate (Zn(NO3)2). The use of the CVD ZnO seed layers with the flat surfaces seems to be a key technique for obtaining thick films instead of vertically aligned nanostructures as reported in many literatures. All the hydrothermal ZnO layers showed the large grains with hexagonal end facets and were highly oriented towards the c-axis direction. Photoluminescence (PL) spectra of the hydrothermal layers were composed of the ultraviolet (UV) emission (370 to 380 nm) and the visible emission (481 to 491 nm), and the intensity ratio of the former emission (I UV) to the latter emission (I VIS) changed, depending on both the molarity of the solution and temperature. It is surprising that all the Hall mobilities for the hydrothermal ZnO layers were significantly larger than those for their corresponding CVD seed films. It was also found that, for the hydrothermal films grown at 70°C to 90°C, the molarity dependences of I UV/I VIS resembled those of mobilities, implying that the mobility in the film is affected by the structural defects. The highest mobility of 166 cm(2)/Vs was achieved on the hydrothermal film with the carrier concentration of 1.65 × 10(17) cm(-3) grown from the aqueous solution of 40 mM at 70°C.
We present a synthesis of large-area single-layer graphene on copper substrate using a refined cooking palm oil, a natural single carbon source, by a home-made spray injector-assisted chemical vapor deposition system. The effects of the distance between spray nozzle and substrate, and growth temperature are studied. From Raman mapping analysis, shorter distance of 1 cm and temperature of around 950 °C lead to the growth of large-area single-layer graphene with a coverage up to 97% of the measured area size of 6400 μm2. The crystallinity of the grown single layer graphene is relatively good due to high distribution percentage of FWHM values of 2D band that is below 30 cm-1. However, the defect concentration is relatively high, and it suggests that a flash-cooling technique needs to be introduced.
ZnO nanorods were synthesized using a low-cost sol-gel spin coating technique. The synthesized nanorods were consisted of hexagonal phase having c-axis orientation. SEM images reflected perpendicular ZnO nanorods forming bridging network in some areas. The impact of different hydrogen concentrations on the Pd-sensitized ZnO nanorods was investigated using an impedance spectroscopy (IS). The grain boundary resistance (Rgb) significantly contributed to the sensing properties of hydrogen gas. The boundary resistance was decreased from 11.95 to 3.765 kΩ when the hydrogen concentration was increased from 40 to 360 ppm. IS gain curve showed a gain of 6.5 for 360 ppm of hydrogen at room temperature. Nyquist plot showed reduction in real part of impedance at low frequencies on exposure to different concentrations of hydrogen. Circuit equivalency was investigated by placing capacitors and resistors to identify the conduction mechanism according to complex impedance Nyquist plot. Variations in nanorod resistance and capacitance in response to the introduction of various concentrations of hydrogen gas were obtained from the alternating current impedance spectra.
Since its introduction in 1995, nanoimprint lithography has been demonstrated in many researches as a simple, low-cost, and high-throughput process for replicating micro- and nanoscale patterns. Due to its advantages, the nanoimprint lithography method has been rapidly developed over the years as a promising alternative to conventional nanolithography processes to fulfill the demands generated from the recent developments in the semiconductor and flexible electronics industries, which results in variations of the process. Roll-to-roll (R2R) nanoimprint lithography (NIL) is the most demanded technique due to its high-throughput fulfilling industrial-scale application. In the present work, a general literature review on the various types of nanoimprint lithography processes especially R2R NIL and the methods commonly adapted to fabricate imprint molds are presented to provide a clear view and understanding on the nanoimprint lithography technique as well as its recent developments.
The enzyme-linked immunosorbent assay (ELISA) has been widely used for disease surveillance and drug screening due to its relatively higher accuracy and sensitivity. Fine-tuning the ELISA is mandatory to elevate the specific detection of biomolecules at a lower abundance. Towards this end, higher molecular capture on the polystyrene (PS) ELISA surface is crucial for efficient detection, and it could be attained by immobilizing the molecules in the correct orientation. It is highly challenging to immobilize protein molecules in a well-aligned manner on an ELISA surface due to charge variations. We employed a 3-(aminopropyl) triethoxysilane (APTES)- and glutaraldehyde (GLU)-coupled PS surface chemical strategy to demonstrate the high performance with ELISA. A potassium hydroxide treatment followed by an equal ratio of 1% APTES and GLU attachment was found to be optimal, and a longer incubation with GLU favored maximum sensitivity. p24 is a vital early secreting antigen for diagnosing human immunodeficiency virus (HIV), and it has been used for efficient detection with the above chemistry. Three different procedures were followed, and they led to the improved detection of the HIV-p24 antigen at 1 nM, which is a 30-fold higher level compared to a conventional ELISA surface. The surface chemical functionalization shown here also displays a higher specificity with human serum and HIV-TAT. The above approach with the designed surface chemistry could also be recommended for disease diagnosis on other sensing surfaces involving the interaction of the probe and the analyte in heterogeneous test samples.
Tuberculosis (TB) is a highly contagious life-threatening disease caused by the bacterial pathogen Mycobacterium tuberculosis. ESAT-6, an abundant early secretory antigenic target protein by M. tuberculosis, found to play a vital role in virulence. Developing a friendly method for the detection of ESAT-6 at the lower concentration facilitates to treat TB at an earlier stage and helps to control the spreading of disease. Herein, a new single-step approach was designed and was done by pre-mixing ESAT-6 and antibody before being added to the gold nanoparticle (GNP) followed by the salt-induced aggregation. We could attain the detection limit of 1.25 pM, showing the aggregation of GNP and the red spectral shift. Further, a higher specificity was demonstrated with the lack of electrostatic biofouling by ESAT-6 on GNP and retained the dispersed GNP in the presence of 10-kDa culture filtrate protein from M. tuberculosis. The required precise antibody concentration for this assay was found to be 60 nM. The increment in the antibody concentration from 75 nM drastically diminishes the sensitivity to ~ 680-fold, due to the crowding effect. With this assay, we attested the suitability of colorimetric assay for efficiently detecting the smaller-sized protein.
Ni-catalyzed Si-based heterostructure nanowires grown on crystal Si substrates by hot-wire chemical vapor deposition (HWCVD) were studied. The nanowires which included NiSi nanowires, NiSi/Si core-shell nanowires, and NiSi/SiC core-shell nanowires were grown by varying the filament temperature T f from 1150 to 1850 °C. At a T f of 1450 °C, the heterostructure nanowires were formed by crystalline NiSi and crystalline Si that were attributed to the core and shell of the nanowires, respectively. The morphology of the nanowires showed significant changes with the increase in the filament temperature to 1850 °C. Moreover, the effect of hydrogen heat transfer from the filament temperature demonstrated significant phase changes from NiSi to Ni2Si with increase in the filament temperature. The increased filament temperature also enhanced reactions in the gas phase thus generating more SiC clusters and consequently formed the NiSi/SiC heterostructure core-shell nanowires at T f of 1850 °C. This paper discusses the role of filament temperatures on the growth and constituted phase change of the nanowires as well as their electrical characteristics.
The junctionless nanowire transistor is a promising alternative for a new generation of nanotransistors. In this letter the atomic force microscopy nanolithography with two wet etching processes was implemented to fabricate simple structures as double gate and single gate junctionless silicon nanowire transistor on low doped p-type silicon-on-insulator wafer. The etching process was developed and optimized in the present work compared to our previous works. The output, transfer characteristics and drain conductance of both structures were compared. The trend for both devices found to be the same but differences in subthreshold swing, 'on/off' ratio, and threshold voltage were observed. The devices are 'on' state when performing as the pinch off devices. The positive gate voltage shows pinch off effect, while the negative gate voltage was unable to make a significant effect on drain current. The charge transmission in devices is also investigated in simple model according to a junctionless transistor principal.
Developing an enhanced diagnosis using biosensors is important for the treatment of patients before disease complications arise. Improving biosensors would enable the detection of various low-abundance disease biomarkers. Efficient immobilization of probes/receptors on the sensing surface is one of the efficient ways to enhance detection. Herein, we introduced the pre-alkaline sensing surface with amine functionalization for capturing gold nanoparticle (GNP) conjugated to human blood clotting factor IX (FIX), and we demonstrated the excellent performance of the strategy. We have chosen the enzyme-linked immunosorbent assay (ELISA) and the interdigitated electrode (IDE), which are widely used, to demonstrate our method. The optimal amount for silanization has been found to be 2.5%, and 15-nm-sized GNPs are ideal and characterized. The limit of FIX detection was attained with ELISA at 100 pM with the premixed GNPs and FIX, which shows 60-fold improvement in sensitivity without biofouling, as compared to the conventional ELISA. Further, FIX was detected with higher specificity in human serum at a 1:1280 dilution, which is equivalent to 120 pM FIX. These results were complemented by the analysis on IDE, where improved detection at 25 pM was achieved, and FIX was detected in human serum at the dilution of 1:640. These optimized surfaces are useful for improving the detection of different diseases on varied sensing surfaces.
Solar energy is one of the ambient sources where energy can be scavenged easily without pollution. Intent scavenging by the solar cell to recollect energy requires a state-of-the-art technique to expedite energy absorption to electron flow for producing more electricity. Structures of the solar cell have been researched to improve absorption efficiency, though most of them can only efficiently absorb with narrow-angle tolerance and polarization sensitivity. So, there is a strong demand for broadband absorption with minimal polarization sensitivity absorber, which is required for effective solar energy harvesting. In this paper, we proposed a new Split Hexagonal Patch Array (SHPA) shape metamaterial absorber with Double-negative (DNG) characteristics, which will provide a wide absorption band with low polarization sensitivity for solar spectrum energy harvesting. The proposed new SHPA shape consists of six nano-arms with a single vertical split which with arrowhead symmetry. This arm will steer electromagnetic (EM) resonance to acquire absolute negative permittivity and permeability, ensuring DNG property. This DNG metamaterial features analyzed based on the photoconversion quantum method for maximum photon absorption. The symmetric characteristics of the proposed structure enable the absorber to show polarization insensitivity and wide incident angle absorption capabilities. Simulated SHPA shows a visible and ultraviolet (UV) spectrum electromagnetic wave absorption capacity of more than 95%. The quantum method gives an advantage in the conversion efficiency of the absorber, and the numerical analysis of the proposed SHPA structure provides absorbance quality for THz regime energy harvesting through solar cell or photonic application.
Nanotechnology, through nanomedicine, allowed drugs to be manipulated into nanoscale sizes for delivery to the different parts of the body, at the same time, retaining the valuable pharmacological properties of the drugs. However, efficient drug delivery and excellent release potential of these delivery systems may be hindered by possible untoward side effects. In this study, the sub-acute toxicity of oral zinc aluminium nanocomposite with and without levodopa was assessed using the Organization for Economic Co-operation and Development guidelines. No sign or symptom of toxicity was observed in orally treated rats with the nanocomposite at 5 and 500 mg/kg concentrations. Body weight gain, feeding, water intake, general survival and organosomatic index were not significantly different between control and treatment groups. Aspartate aminotransferase (AST) in 500 mg/kg levodopa nanocomposite (169 ± 30 U/L), 5 mg/kg levodopa nanocomposite (172 ± 49 U/L), and 500 mg/kg layered double hydroxides (LDH) nanocomposite (175 ± 25 U/L) were notably elevated compared to controls (143 ± 05 U/L); but the difference were not significant (p > 0.05). However, the differences in aspartate aminotransferase/alanine aminotransferase (AST/ALT) ratio of 500 mg/kg levodopa nanocomposite (0.32 ± 0.12) and 500 mg/kg LDH nanocomposite (0.34 ± 0.12) were statistically significant (p
Layered double hydroxide (LDH) is an inorganic-organic nano-layered material that harbours drug between its two-layered sheets, forming a sandwich-like structure. It is attracting a great deal of attention as an alternative drug delivery (nanodelivery) system in the field of pharmacology due to their relative low toxic potential. The production of these nanodelivery systems, aimed at improving human health through decrease toxicity, targeted delivery of the active compound to areas of interest with sustained release ability. In this study, we administered zinc-aluminium-LDH-levodopa nanocomposite (ZAL) and zinc-aluminium nanocomposite (ZA) to Sprague Dawley rats to evaluate for acute oral toxicity following OECD guidelines. The oral administration of ZAL and ZA at a limit dose of 2,000 mg/kg produced neither mortality nor acute toxic signs throughout 14 days of the observation. The percentage of body weight gain of the animals showed no significant difference between control and treatment groups. Animal from the two treated groups gained weight continuously over the study period, which was shown to be significantly higher than the weight at the beginning of the study (P
Graphene oxide (GO) film was evaporated onto graphite and used as an electrode to produce electrochemically reduced graphene oxide (ERGO) films by electrochemical reduction in 6 M KOH solution through voltammetric cycling. Fourier transformed infrared and Raman spectroscopy confirmed the presence of ERGO. Electrochemical impedance spectroscopy characterization of ERGO and GO films in ferrocyanide/ferricyanide redox couple with 0.1 M KCl supporting electrolyte gave results that are in accordance with previous reports. Based on the EIS results, ERGO shows higher capacitance and lower charge transfer resistance compared to GO.
Verapamil is a calcium channel blocker and highly effective in the treatment of hypertension, angina pectoris, and other diseases. However, the drug has a low bioavailability of 20 to 35% due to the first pass effect. The main objective of this study was to develop hybrid verapamil-dextran nanostructured lipid carriers (HVD-NLCs) in an attempt to increase verapamil cellular uptake. The formulations were successfully prepared by a high-shear homogenization method and statistically optimized using 24 full factorial design. The HVD-NLCs formulations were freeze-dried using trehalose as a cryoprotectant. The results showed that the optimized formula (VER-9) possessed a particle size (PS), polydispersity index (PDI), and the percentage of entrapment efficiency (%EE) of 192.29 ± 2.98, 0.553 ± 0.075, and 93.26 ± 2.66%, respectively. The incorporation of dextran sulfate in the formulation had prolonged the release of verapamil (~ 85% in 48 h) in the simulated gastric fluid (pH 1.2) and simulated intestinal fluid (pH 6.8). The differential scanning calorimetry analysis showed no chemical interaction between verapamil and the excipients in the formulation. While wide-angle X-ray scattering studies demonstrated the drug in the amorphous form after the incorporation in the NLCs. The transmission electron microscopy and scanning electron microscopy images revealed that the nanoparticles had spherical shape. The cellular uptake study using Caco-2 cell line showed a higher verapamil uptake from HVD-NLCs as compared to verapamil solution and verapamil-dextran complex. The optimized formulation (VER-9) stored in the refrigerated condition (5 °C ± 3 °C) was stable for 6 months. In conclusion, the HVD-NLCs were potential carriers for verapamil as they significantly enhanced the cellular uptake of the drug.
This paper presents a numerical study of the thermal performance of fins mounted on the bottom wall of a horizontal channel and cooled with either pure water or an Al2O3-water nanofluid. The bottom wall of the channel is heated at a constant temperature and cooled by mixed convection of laminar flow at a relatively low temperature. The results of the numerical simulation indicate that the heat transfer rate of fins is significantly affected by the Reynolds number (Re) and the thermal conductivity of the fins. The influence of the solid volume fraction on the increase of heat transfer is more noticeable at higher values of the Re.