Acute and chronic effects of insecticide-endosulfan on the survival and reproduction performance of Moina macrocopa were determined in a laboratory study. Endosulfan concentrations that cause 50% mortality (LC50) after exposure for 24 and 48 h were 3.34 and 0.16 mg L(-1), respectively. Average longevity, initial age of reproduction and intrinsic rate of natural increase were reduced at 0.002 mg L(-1). Fecundity was greatly reduced by about 70% at 0.0004 mg L(-1) and approximately 97% at 0.002 mg L(-1) as compared to control organisms throughout the whole life span of 15 days. If environmental concentration of endosulfan do not exceed 0.0004 mg L(-1), application of this insecticide is unlikely to induce detrimental effects on these cladoceran populations in agro-ecosystem.
The rate of dye adsorption from aqueous effluents onto palm kernel shell (PKS) activated carbon has been studied experimentally using the batch adsorption method. The adsorption rates of methylene blue on PKS for systems of different initial dye concentrations are modeled using a film-pore-concentration dependent surface diffusion (FPCDSD) model. The FPCDSD model is sufficiently general and can be reduced easily to describe other simplified models. Using the FPCDSD model, only a single set of mass transfer parameters is required to describe the methylene blue/PKS system for different initial concentrations. A different set of mass transfer parameters are needed to obtain the best fitting if the pore diffusion is not included in the model.
The removal of Reactive Black 5 dye in an aqueous solution by electrocoagulation (EC) as well as addition of flocculant was investigated. The effect of operational parameters, i.e. current density, treatment time, solution conductivity and polymer dosage, was investigated. Two models, namely the artificial neural network (ANN) and the response surface method (RSM), were used to model the effect of independent variables on percentage of dye removal. The findings of this work showed that current density, treatment time and dosage of polymer had the most significant effect on percentage of dye removal (p<0.001). In addition, interaction between time and current density, time and dosage of polymer, current density and dosage of polymer also significantly affected the percentage of dye removal (p=0.034, 0.003 and 0.024, respectively). It was shown that both the ANN and RSM models were able to predict well the experimental results (R(2)>0.8).
Produced water or oilfield wastewater is the largest volume ofa waste stream associated with oil and gas production. The aim of this study was to investigate the biological pretreatment of synthetic and real produced water in a sequencing batch reactor (SBR) to remove hydrocarbon compounds. The SBR was inoculated with isolated tropical halophilic microorganisms capable of degrading crude oil. A total sequence of 24 h (60 min filling phase; 21 h aeration; 60 min settling and 60 min decant phase) was employed and studied. Synthetic produced water was treated with various organic loading rates (OLR) (0.9 kg COD m(-3) d(-1), 1.8 kg COD m(-3) d(-1) and 3.6 kg COD m(-3) d(-1)) and different total dissolved solids (TDS) concentration (35,000 mg L(-1), 100,000 mg L(-1), 150,000 mg L(-1), 200,000 mg L(-1) and 250,000 mg L(-1)). It was found that with an OLR of 0.9 kg COD m(-3) d(-1) and 1.8 kg COD m(-3) d(-1), average oil and grease (O&G) concentrations in the effluent were 7 mg L(-1) and 12 mg L(-1), respectively. At TDS concentration of 35,000 mg L(-1) and at an OLR of 1.8 kg COD m(-3)d(-1), COD and O&G removal efficiencies were more than 90%. However, with increase in salt content to 250,000 mg L(-1), COD and O&G removal efficiencies decreased to 74% and 63%, respectively. The results of biological treatment of real produced water showed that the removal rates of the main pollutants of wastewater, such as COD, TOC and O&G, were above 81%, 83%, and 85%, respectively.