The fabrication of bi-material micro-components via two-component micro-powder injection moulding (2C-µPIM) from 3 mol% yttria-stabilised zirconia (3YSZ) and micro/nano bimodal stainless steel 316L (SS 316L) powders has received insufficient attention. Apart from this, retaining the bonding between ceramic and metal at different processing stages of 2C-µPIM is challenging. This study investigated the solvent and thermal debinding mechanisms of green bi-material micro-parts of 3YSZ and bimodal SS 316L without collapsing the ceramic/metal joining. In this research, feedstocks were prepared by integrating the powders individually with palm stearin and low-density polyethylene binders. The results demonstrated that during the solvent debinding process, the palm stearin removal rate in the bi-materials composed of 3YSZ and bimodally configured SS 316L feedstocks intensified with an increase in temperature. The establishment of interconnected pores in the solvent-debound components facilitated the thermal debinding process, which removed 99% of the binder system. Following sintering, the debound bi-materials exhibited a relative density of 95.3%. According to a study of the microstructures using field emission scanning electron microscopy, an adequate bond between 3YSZ and bimodal SS 316L was established in the micro-part after sintering. The bi-material sintered at 1350 °C had the highest hardness of 1017.4 HV along the joining region.
The micro-scale joining of two different materials using two-component micro-powder injection molding (2C-µPIM) is an intriguing technique. The formation of defects in bi-materials at different processing stages makes this technique challenging. This study presents the fabrication of defect-free bi-material micro-parts containing hydroxyapatite (HA) and 3 mol% yttria-stabilized zirconia (3YSZ) via 2C-µPIM. Critical powder volume concentrations (CPVCs) of 61.7 vol% and 47.1 vol% were obtained for the HA and 3YSZ powders, respectively. Based on the CPVCs, the optimal loadings for the HA and 3YSZ powders were selected as 60 vol% and 45 vol%, respectively. The HA and 3YSZ feedstocks were prepared by separately mixing the optimal powder contents with low-density polyethylene (LDPE) and palm stearin binders. The feedstocks displayed pseudoplastic behavior, and the lowest ranges of viscosity for the HA and 3YSZ at a temperature of 180 °C were 157.1-1392.5 Pa·s and 726.2-985.5 Pa·s, respectively. The feedstocks were injected to produce green HA/3YSZ micro-sized components. It was found that a solvent debinding temperature of 70 °C removed 60.6% of the palm stearin binder from the sample. In the thermal debinding stage, the open channels that formed in the bi-material sample's solvent debound at 70 °C and contributed to the removal of 93 to 95% of the binder system. When the debound bi-materials were sintered at 1300 °C, the highest relative density of 96.3% was obtained. The sintering operation revealed a linear shrinkage between 13 and 17% in the sintered HA/3YSZ micro-parts.
Two-component micro-powder injection moulding (2C-μPIM) is a prospective approach for fabricating bi-material micro-components of stainless steel 316L (SS316L) and 3 mol% yttria-stabilised zirconia (3YSZ) at an appealing cost. However, the fundamental challenge lies in preventing the formation of large-scale cracks at the interface of two different materials during sintering. This study investigated how SS316L nanoparticles in bimodally configured SS316L powder that incorporated both nanoparticles and microparticles influenced the sintering of 2C-μPIM-processed miniature bi-materials made of bimodal SS316L and 3YSZ. In this study, feedstocks were developed by integrating monomodal (micro-sized) SS316L powder, three types of nano/micro-bimodal SS316L powders, and 3YSZ powder individually with palm stearin and low-density polyethylene binders. The results indicated that increasing the SS316L nanoparticle content to 45 vol.% caused a 19.5% increase in the critical powder loading in the bimodal SS316L powder as compared to that in the monomodal SS316L powder. The addition of SS316L nanoparticles increased the relative density and hardness of the sintered bi-materials, with the maximum values obtained being 96.8% and 1156.8 HV, respectively. Field emission scanning electron microscopy investigations revealed that adding 15 vol.% and 30 vol.% SS316L nanoparticle contents reduced interface cracks in bi-materials significantly, while 45 vol.% resulted in a crack-free interface.