Displaying publications 1 - 20 of 41 in total

Abstract:
Sort:
  1. Sen RN, Yeow PH
    Int J Occup Saf Ergon, 2003;9(1):57-74.
    PMID: 12636892
    The study aimed at reducing the occupational health and safety problems faced by the manual component insertion operators. Subjective and objective assessments, and direct observations were made in the printed circuit assembly factory. Simple and low-cost ergonomic interventions were implemented, that is, repairing chairs, reducing high workloads, assigning operators to a maximum of 2 workstations, confining machines that emitted bad smell and much noise, and providing finger work aids. The results of the interventions were reductions in operators' work discomforts, that is, chair discomfort (by 90%), high work stress, and discomfort due to profound change in their workstations. Their health hazards were also eliminated, that is, inhalation of toxic fumes, exposure to too much noise, and pain due to pressing sharp components.
  2. Yeow PH, Sen RN
    Int J Occup Saf Ergon, 2004;10(4):369-85.
    PMID: 15598361
    An ergonomics improvement study was conducted on the visual inspection process of a printed circuit assembly (PCA) factory. The process was studied through subjective assessment and direct observation. Three problems were identified: operators' eye problems, insufficient time for inspection and ineffective visual inspection. These problems caused a huge yearly rejection cost of US 298,240 dollars, poor quality, customer dissatisfaction and poor occupational health and safety. Ergonomics interventions were made to rectify the problems: reduced usage of a magnifying glass, the use of less glaring inspection templates, inspection of only electrically non-tested components and introduction of a visual inspection sequence. The interventions produced savings in rejection cost, reduced operators' eye strain, headaches and watery eyes, lowered the defect percentage at customers' sites and increased the factory's productivity and customer satisfaction.
  3. Dawal SZ, Taha Z
    Int J Occup Saf Ergon, 2006;12(3):267-80.
    PMID: 16984786
    A methodology was developed for diagnosing industrial work, which includes questionnaire, observation, measurements, data collection and statistical analysis. A survey was conducted to investigate the relationship between job satisfaction and factors that affect work design in 2 automotives manufacturing companies in Malaysia. A basic work design model was proposed. The aim of this model was to determine the factors that influence employees' perception towards their work. A set of multiple-choice questionnaires was developed and data was collected by interviewing employees at a production plant. The survey focused on job and environmental factors. The results supported the proposed model and showed that job and environmental factors were significantly related to job satisfaction. They highlighted the significant influence of age, work experience and marital status on job satisfaction. Further, environmental factors, especially the surroundings, context dependence and the building's function, also had a significant impact on job satisfaction.
  4. Mallick Z
    Int J Occup Saf Ergon, 2007;13(3):291-303.
    PMID: 17888238
    The last 20 years have seen a tremendous growth in mobile computing and wireless communications and services. An experimental study was conducted to explore the effect of text/background color on a laptop computing system along with variable environmental vibration on operators' data entry task performance in moving automobiles. The operators' performance was measured in terms of the number of characters entered per minute without spaces (NCEPMWS) on a laptop computing system. The subjects were divided into 3 categories, namely, Novices, Intermediates and Experts. Findings suggest a re-evaluation of existing laptop designs taking ergonomics into consideration. It appears that proper selection of text/background color on the laptop coupled with controlled vehicular speed could result in a better quality of interaction between human and laptops and it could also resolve the problem of poor data entry task performance.
  5. Mallick Z
    Int J Occup Saf Ergon, 2008;14(3):343-9.
    PMID: 18954544
    The grass trimming machine is a widely used agricultural machine for cutting grass by the roadside and in other areas in Malaysia. Hand-arm vibration (HAV) syndrome is very common among workers operating power tools and performing similar work for extended periods. Grass trimming involves the use of a motorized cutter spinning at high speed, resulting in high levels of HAV among its operators. The existing D-shape handle causes HAV-related stress and operational load in operators. This research proposes a new design of a handle of the grass trimming machine. When this new design was compared with the old one, it was found that the new handle resulted in 18% lower HAV. To find the lowest HAV, 3 critical parameters of the new handle (length, angle and material of the cap of the handle) were optimized using the Taguchi quality tool. Appropriately selected parameters of the new handle significantly reduced the occurrence of HAV among grass trimmers.
  6. Zakerian SA, Subramaniam ID
    Int J Occup Saf Ergon, 2009;15(4):425-34.
    PMID: 20003776
    Increasing numbers of workers use computer for work. So, especially among office workers, there is a high risk of musculoskeletal discomforts. This study examined the associations among 3 factors, psychosocial work factors, work stress and musculoskeletal discomforts. These associations were examined via a questionnaire survey on 30 office workers (at a university in Malaysia), whose jobs required an extensive use of computers. The questionnaire was distributed and collected daily for 20 days. While the results indicated a significant relationship among psychosocial work factors, work stress and musculoskeletal discomfort, 3 psychosocial work factors were found to be more important than others in both work stress and musculoskeletal discomfort: job demands, negative social interaction and computer-related problems. To further develop study design, it is necessary to investigate industrial and other workers who have experienced musculoskeletal discomforts and work stress.
  7. Bin WS, Richardson S, Yeow PH
    Int J Occup Saf Ergon, 2010;16(3):345-56.
    PMID: 20828490
    The study aimed to conduct an ergonomic intervention on a conventional line (CL) in a semiconductor factory in Malaysia, an industrially developing country (IDC), to improve workers' occupational health and safety (OHS). Low-cost and simple (LCS) ergonomics methods were used (suitable for IDCs), e.g., subjective assessment, direct observation, use of archival data and assessment of noise. It was found that workers were facing noise irritation, neck and back pains and headache in the various processes in the CL. LCS ergonomic interventions to rectify the problems included installing noise insulating covers, providing earplugs, installing elevated platforms, slanting visual display terminals and installing extra exhaust fans. The interventions cost less than 3 000 USD but they significantly improved workers' OHS, which directly correlated with an improvement in working conditions and job satisfaction. The findings are useful in solving OHS problems in electronics industries in IDCs as they share similar manufacturing processes, problems and limitations.
  8. Zadry HR, Dawal SZ, Taha Z
    Int J Occup Saf Ergon, 2011;17(4):373-84.
    PMID: 22152503
    A study was conducted to investigate the effects of repetitive light tasks of low and high precision on upper limb muscles and brain activities. Surface electromyography (EMG) and electroencephalography (EEG) were used to measure the muscle and brain activity of 10 subjects. The results show that the root-mean-square (RMS) and mean power frquency (MPF) of the muscle activity and the mean power of the EEG alpha bands were higher on the high-precision task than on the low-precision one. There was also a high and significant correlation between upper limb muscle and brain activity during the tasks. The longer the time and the more precise the task, the more the subjects become fatigued both physically and mentally. Thus, these results could be potentially useful in managing fatigue, especially fatique related to muscle and mental workload.
  9. Halim I, Omar AR
    Int J Occup Saf Ergon, 2012;18(1):85-96.
    PMID: 22429532
    Many occupations in industry such as metal stamping workers, electronics parts assembly operators, automotive industry welders, and lathe operators require working in a standing posture for a long time. Prolonged standing can contribute to discomfort and muscle fatigue particularly in the back and legs. This study developed the prolonged standing strain index (PSSI) to quantify the risk levels caused by standing jobs, and proposed recommendations to minimize the risk levels. Risk factors associated with standing jobs, such as working posture, muscles activity, standing duration, holding time, whole-body vibration, and indoor air quality, were the basis for developing the PSSI. All risk factors were assigned multipliers, and the PSSI was the product of those multipliers. Recommendations for improvement are based on the PSSI; however, extensive studies are required to validate their effectiveness. multipliers, and the PSSI was the product of those multipliers. Recommendations for improvement are based on the PSSI; however, extensive studies are required to validate their effectiveness.
  10. Dawal SZ, Zadry HR, Azmi SN, Rohim SR, Sartika SJ
    Int J Occup Saf Ergon, 2012;18(4):461-72.
    PMID: 23294660
    This paper presents an anthropometric database of high school and university students from Kuala Lumpur, Malaysia. Forty-one high school participants (21 males and 20 females), 13-17 years old, and 143 university students (74 males and 69 females) took part in the study. Twenty-one static body dimensions were measured. The greatest mean differences in the anthropometric data between male and female high school students were found in the sitting elbow height. In addition, a comparison of anthropometric data of male and female university students showed that data for males and females were significantly different, except for buttock-popliteal length, sitting elbow height and thigh clearance. The primary aim of this study was to develop an anthropometric database that could be used as a primary reference in designing products, devices and equipment for ergonomic learning environments.
  11. Chong HY, Low TS
    Int J Occup Saf Ergon, 2014;20(3):503-13.
    PMID: 25189753
    Safety and health issues remain critical to the construction industry due to its working environment and the complexity of working practises. This research attempts to adopt 2 research approaches using statistical data and court cases to address and identify the causes and behavior underlying construction safety and health issues in Malaysia. Factual data on the period of 2000-2009 were retrieved to identify the causes and agents that contributed to health issues. Moreover, court cases were tabulated and analyzed to identify legal patterns of parties involved in construction site accidents. Approaches of this research produced consistent results and highlighted a significant reduction in the rate of accidents per construction project in Malaysia.
  12. Azmir NA, Ghazali MI, Yahya MN, Ali MH
    PMID: 27050159
    Prolonged exposure to hand-transmitted vibration from grass-cutting machines has been associated with increasing occurrences of symptoms and signs of occupational diseases related to hand-arm vibration syndrome (HAVS).
  13. Puah LN, Ong LD, Chong WY
    Int J Occup Saf Ergon, 2016 Sep;22(3):333-9.
    PMID: 27049935 DOI: 10.1080/10803548.2016.1159390
    Although knowledge is cumulating, very little is known about the effects of various sources of support on safety and health compliance. This study goes beyond previous research by investigating the relationships among perceived support from organizations, supervisors and co-workers, and employees' safety and health compliance behaviour at chemical and petroleum process plants. The results of this study show that the support from organizations, supervisors and co-workers was significantly related to employees' safety and health compliance. Also, the findings reveal that perceived supervisor support has the strongest influence in ensuring employees' safety and health compliance behaviour.
  14. Zadry HR, Dawal SZ, Taha Z
    Int J Occup Saf Ergon, 2016 Sep;22(3):374-83.
    PMID: 27053140 DOI: 10.1080/10803548.2016.1150094
    This study was conducted to develop muscle and mental activities on repetitive precision tasks. A laboratory experiment was used to address the objectives. Surface electromyography was used to measure muscle activities from eight upper limb muscles, while electroencephalography recorded mental activities from six channels. Fourteen university students participated in the study. The results show that muscle and mental activities increase for all tasks, indicating the occurrence of muscle and mental fatigue. A linear relationship between muscle activity, mental activity and time was found while subjects were performing the task. Thus, models were developed using those variables. The models were found valid after validation using other students' and workers' data. Findings from this study can contribute as a reference for future studies investigating muscle and mental activity and can be applied in industry as guidelines to manage muscle and mental fatigue, especially to manage job schedules and rotation.
  15. Sukadarin EH, Deros BM, Ghani JA, Mohd Nawi NS, Ismail AR
    Int J Occup Saf Ergon, 2016 Sep;22(3):389-98.
    PMID: 27173135 DOI: 10.1080/10803548.2016.1156924
    INTRODUCTION: This review describes standardized ergonomics assessment based on pen-and-paper observational methods for assessing ergonomics risk factors.

    OBJECTIVE: The three main objectives are to analyze published pen-and-paper observational methods, to extract and understand the risk levels of each method and to identify their associated health effects.

    METHODOLOGY: The authors searched scientific databases and the Internet for materials from 1970 to 2013 using the following keywords: ergo, posture, method, observational, postural angle, health effects, pain and diseases. Postural assessments of upper arms, lower arms, wrists, neck, back and legs in six pen-and-paper-based observational methods are highlighted, extracted in groups and linked with associated adverse health effects.

    RESULTS: The literature reviewed showed strengths and limitations of published pen-and-paper-based observational methods in determining the work activities, risk levels and related postural angles to adverse health effects. This provided a better understanding of unsafe work postures and how to improve these postures.

    CONCLUSION: Many pen-and-paper-based observational methods have been developed. However, there are still many limitations of these methods. There is, therefore, a need to develop a new pen-and-paper-based observational method for assessing postural problems.

  16. Ahmed I, Shaukat MZ, Usman A, Nawaz MM, Nazir MS
    Int J Occup Saf Ergon, 2018 Jun;24(2):240-250.
    PMID: 28795938 DOI: 10.1080/10803548.2017.1366145
    This research covers the current status of occupational health and safety (OHS)-related practices in the informal construction segment of Pakistan. Data were collected, through interviews, from 316 construction sites employing 3577 workers. The results of the study reveal that both employers and workers lack knowledge of OHS laws/standards and no practices of this nature are enacted at these construction sites. Alarmingly, work-related accidents, whenever they happen, are not given due attention and there is no formal injury-report system. The informal construction industry employs a huge portion of the informal workforce, and lack of OHS happens at tremendous human cost. These research findings may thus play their role in strengthening the case for reforms in the sector. This study, if properly utilized, may also enable employers of the sector by increasing their knowledge about OHS practices and, as a result, trying to offer safer environments for their workers.
  17. Ab-Murat N, Mason L, Kadir RA, Yusoff N
    Int J Occup Saf Ergon, 2018 Jun;24(2):233-239.
    PMID: 28010176 DOI: 10.1080/10803548.2016.1268869
    PURPOSE: To assess Malaysian dentists' perceptions of their mental well-being.

    METHODS: A self-administered questionnaire was developed based on a conceptual framework of mental health and well-being model. Two aspects were assessed, namely the physiological (two domains) and the psychological (six domains). Participants were asked to rate their experiences of the aforementioned aspects using a 5-point Likert scale ranging from all the time to never.

    RESULTS: The response rate was 81%. Most of the dentists (61.7%) perceived having positive mental well-being. Under the physiological aspect, most respondents reported that they were 'generally happy' (93.3%), but about 30% stated they were 'stressed physically and emotionally'. Of the six domains under the psychological aspect, positive well-being was observed in the 'sense of coherence' and 'behavioural stress' domains. Participants who were above 40 years old, married and had children reported having a more positive mental well-being when compared with their counterparts.

    CONCLUSION: Overall, most Malaysian dentists perceived having a positive mental well-being. It is crucial, however, to closely monitor and initiate early interventions for those with negative symptoms to ensure the safe practice of dentistry.

  18. Jaafar MH, Arifin K, Aiyub K, Razman MR, Ishak MIS, Samsurijan MS
    Int J Occup Saf Ergon, 2018 Dec;24(4):493-506.
    PMID: 28849991 DOI: 10.1080/10803548.2017.1366129
    The construction industry plays a significant role in contributing to the economy and development globally. During the process of construction, various hazards coupled with the unique nature of the industry contribute to high fatality rates. This review refers to previous published studies and related Malaysian legislation documents. Four main elements consisting of human, worksite, management and external elements which cause occupational accidents and illnesses were identified. External and management elements are the underlying causes contributing to occupational safety and health (OSH), while human and worksite elements are more apparent causes of occupational accidents and illnesses. An effective OSH management approach is required to contain all hazards at construction sites. An approach to OSH management constructed by elements of policy, process, personnel and incentive developed in previous work is explored. Changes to the sub-elements according to previous studies and the related Malaysian legislation are also covered in this review.
  19. Hariri A, Mohamad Noor N, Paiman NA, Ahmad Zaidi AM, Zainal Bakri SF
    Int J Occup Saf Ergon, 2018 Dec;24(4):646-651.
    PMID: 28849717 DOI: 10.1080/10803548.2017.1368950
    Welding operations are rarely conducted in an air-conditioned room. However, a company would set its welding operations in an air-conditioned room to maintain the humidity level needed to reduce hydrogen cracks in the specimen being welded. This study intended to assess the exposure to metal elements in the welders' breathing zone and toenail samples. Heavy metal concentration was analysed using inductively coupled plasma mass spectrometry. The lung function test was also conducted and analysed using statistical approaches. Chromium and manganese concentrations in the breathing zone exceeded the permissible exposure limit stipulated by Malaysian regulations. A similar trend was obtained in the concentration of heavy metals in the breathing zone air sampling and in the welders' toenails. Although there was no statistically significant decrease in the lung function of welders, it is suggested that exposure control through engineering and administrative approaches should be considered for workplace safety and health improvement.
  20. Awang Lukman K, Jeffree MS, Rampal KG
    Int J Occup Saf Ergon, 2019 Mar;25(1):8-16.
    PMID: 28978270 DOI: 10.1080/10803548.2017.1388571
    A cross-sectional study was undertaken to determine the prevalence of lower back pain (LBP) and its association with whole-body vibration (WBV) and manual materials handling (MMH). We studied 110 commercial vehicle drivers using a self-administered questionnaire and the VI-400Pro human vibration monitor. Prevalence of LBP was 66.4%. The percentage of drivers who had frequent manual handling of heavy loads was 45.5% and those who handled heavy loads in awkward postures accounted for 86.4%. Daily vibration A(8) averaged on the z axis was 0.25 (0.06) m·s-2 and at vector sum was 0.29 (0.07) m·s-2. Daily vibration exposures on the z axis, frequent manual handling of heavy loads and awkward posture during MMH were significantly associated with LBP. Drivers who are exposed to WBV and frequently handle heavy loads manually and with awkward postures probably have more LBP than drivers who are exposed to only one of these risk factors.
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links