The use of a self-inflating tissue expander is a technique to stretch cutaneous tissues for potential use in reconstructive skin surgeries. This study investigates the mechanical properties of horse skin stretched by the subcutaneous implantation of anisotropic tissue expanders at the forehead, right shoulder, and dorsomedial part of the cannon region of the right forelimb in six (n = 6) horses. After 14 days of skin expansion, expanded and normal (control) skin samples were harvested and their mechanical properties of elastic modulus (EM), maximum force (MF), maximum stress (MSs) and maximum strain (MSr) were evaluated using uniaxial tension test. The expanded skin from shoulder area has higher EM, MSs, MSr and MF than the normal skin when compared to the forehead and lower forelimb. Statistically, there was a significant (P= .02) mean difference for MSs between the expanded shoulder and lower forelimb skin, but the pairwise comparison of EM, MSr and MF showed no significant difference between the locations. The overall effect of locations on EM and MSs was statistically significant (P < .05), however, there was no overall effect of horse factor, treatment factor (normal and expanded skin) and location interaction on the EM, MSS, MF and MSr. In conclusion, the expanded skin from the frontal head and the distal limb are less elastic (stiffer) compared to that of the expanded skin of the shoulder, thus anatomical location of the skin has some degree of effect on EM and MSs.
Armalcolite, a rare ceramic mineral and normally found in the lunar earth, was synthesized by solid-state step-sintering. The in situ phase-changed novel ceramic nanocrystals of Ca-Mg-Ti-Fe based oxide (CMTFOx), their chemical reactions and bonding with polydimethylsiloxane (PDMS) were determined by X-ray diffraction, infrared spectroscopy, and microscopy. Water absorption of all the CMTFOx was high. The lower dielectric loss tangent value (0.155 at 1 MHz) was obtained for the ceramic sintered at 1050 °C (S1050) and it became lowest for the S1050/PDMS nanocomposite (0.002 at 1 MHz) film, which was made by spin coating at 3000 rpm. The excellent flexibility (static modulus ≈ 0.27 MPa and elongation > 90%), viscoelastic property (tanδ = E″/E': 0.225) and glass transition temperature (Tg: -58.5 °C) were obtained for S1050/PDMS film. Parallel-plate capacitive and flexible resistive humidity sensors have been developed successfully. The best sensing performance of the present S1050 (3000%) and its flexible S1050/PDMS composite film (306%) based humidity sensors was found to be at 100 Hz, better than conventional materials.
Despite the many attractive potential uses of ceramic materials as humidity sensors, some unavoidable drawbacks, including toxicity, poor biocompatibility, long response and recovery times, low sensitivity and high hysteresis have stymied the use of these materials in advanced applications. Therefore, in present investigation, we developed a capacitive humidity sensor using lead-free Ca,Mg,Fe,Ti-Oxide (CMFTO)-based electro-ceramics with perovskite structures synthesized by solid-state step-sintering. This technique helps maintain the submicron size porous morphology of the developed lead-free CMFTO electro-ceramics while providing enhanced water physisorption behaviour. In comparison with conventional capacitive humidity sensors, the presented CMFTO-based humidity sensor shows a high sensitivity of up to 3000% compared to other materials, even at lower signal frequency. The best also shows a rapid response (14.5 s) and recovery (34.27 s), and very low hysteresis (3.2%) in a 33%-95% relative humidity range which are much lower values than those of existing conventional sensors. Therefore, CMFTO nano-electro-ceramics appear to be very promising materials for fabricating high-performance capacitive humidity sensors.
Since humidity sensors have been widely used in many sectors, a suitable humidity sensing material with improved sensitivity, faster response and recovery times, better stability and low hysteresis is necessary to be developed. Here, we fabricate a uniformly porous humidity sensor using Ca, Ti substituted Mg ferrites with chemical formula of CaMgFe1.33Ti₃O12 as humidity sensing materials by solid-sate step-sintering technique. This synthesis technique is useful to control the grain size with increased porosity to enhance the hydrophilic characteristics of the CaMgFe1.33Ti₃O12 nanoceramic based sintered electro-ceramic nanocomposites. The highest porosity, lowest density and excellent surface-hydrophilicity properties were obtained at 1050 °C sintered ceramic. The performance of this impedance type humidity sensor was evaluated by electrical characterizations using alternating current (AC) in the 33%-95% relative humidity (RH) range at 25 °C. Compared with existing conventional resistive humidity sensors, the present sintered electro-ceramic nanocomposite based humidity sensor showed faster response time (20 s) and recovery time (40 s). This newly developed sensor showed extremely high sensitivity (%S) and small hysteresis of <3.4%. Long-term stability of the sensor had been determined by testing for 30 consecutive days. Therefore, the high performance sensing behavior of the present electro-ceramic nanocomposites would be suitable for a potential use in advanced humidity sensors.
Background: The high prevalence and impacts of orofacial pain (OFP) have caused major sufferings to individuals and society. The purpose of the study was to investigate the problems and impacts of OFP among a group of Malaysian aborigines. The objectives were to determine (i) the prevalence, aetiology, duration, severity, types and persistence of OFP during the past 3 months preceding the study; (ii) its associated impact on daily performance; and (iii) the measures taken for pain relief.
Methods: This is a cross sectional study carried out in Kuala Lipis, Pahang involving 6 villages of Orang Asli Bateq and Semai. Study sample was chosen using convenient sampling including adults aged 16 years and above. Participants were invited for an interview using structured questionnaire followed by clinical examination. Data analysis was carried out using SPSS ver12.
Results: Response rate was low at 20% (n = 140). Over one-quarter (26.4%) of the sample experienced OFP in the previous 3 months. Toothache was found to be the main aetiology (83.3%) followed by gingival pain (18.9%), temporomandibular joint (10.8%) and facial pain (8.1%). Mean duration of pain was 9.8 days for toothache, 162.4 days for gingival pain, 7.3 days for TMJ and 5.7 days for facial pain. Of those who had OFP, over half rated the pain as moderate (37.8%) and severe (29.7%) and most of the pain was ‘intermittent’ in nature (81.1%). Over half (62.2%) admitted the pain had disappeared during the interview. In terms of pain relief, 56.8% of the sample used traditional medicine. The pain had impacted on the chewing ability (70.3%, p=0.01), ability to sleep at night (73.0%, p<0.001), levels of anxiety (70.3%), ability to perform daily chores (33.3%) and social life (35.1%) of the Orang Asli sample.
Conclusion: This study suggests the prevalence of OFP was high among the Orang Asli sample, which imposed considerable physical and psychological impacts on daily life.
Key words: orofacial pain; impacts; quality of life; Malaysian aborigines