This paper studies about water obtained from fish pond of fisheries research centre. Usual water
quality parameters such as pH, COD, Turbidity and Ammonia content were analyzed before and
after irradiation. Electron beam irradiation was used to irradiate the water with the dose 100 kGy,
200 kGy and 300 kGy. Only high dose was applied on this water as only a limited amount of
samples was supplied. All the parameters indicated a slight increase after irradiation except for the
ammonia content, which showed a gradual decrease as irradiation dose increases. Sample
condition was changed before irradiation in order to obtain more effective results in the following
batch. The water sample from fisheries was diluted with distilled water to the ratio of 1:1.This was
followed with irradiation at 100 kGy, 200 kGy and 300 kGy. The results still showed an increase in
all parameters after irradiation except for ammonia content. For the following irradiation batch,
the pH of the sample was adjusted to pH 4 and pH 8 before irradiation. For this sample the
irradiation dose selected was only 100 kGy. A higher value of ammonia was observed for the
sample with pH 4 after irradiation. Other parameters were almost the same as the first two batches
Radiation processing of food materials by gamma-radiation is a well-established method for
microbial decontamination and insect disinfestation. Irradiation of spices at doses ranging from
10 to 30 kGy has been reported to result in complete elimination of microorganisms with
negligible changes in the flavour quality. The effect of gamma-radiation on microflora and
vanillin content of cured vanilla beans in the dose range of 5 - 50 kGy has been investigated, but
its effect on other major aroma compounds and vanillin glucoside (vanillin aroma precursor)
remaining after curing have not been studied so far. Vanillin (4-hydroxy-3-methoxybenzaldehyde)
is one such compound used as a flavouring agent and as a dietary component. It is the major
component of natural vanilla, which is one of the most widely used and important flavouring
materials throughout the world. Vanillin is an antioxidant capable of protecting membrane
against lipid peroxidation and DNA against strand breaks induced by reactive oxygen species.
The present work was aimed to study the effect of gamma-radiation processing on the major
aroma compounds of cured vanilla beans and also to investigate possible enhancement in vanillin
content by the radiolytic breakdown of vanillin glucoside present already. Cured vanilla beans
were irradiated (5, 10, 15, 20 and 30 kGy) and the vanillin content of control and irradiated
samples were analysed, respectively for possible enhancement of vanillin content by radiolysis of
vanillin glucoside. Radiolytic breakdown of glycosidic precursors of aroma constituents and
consequent release of free aroma was shown to result in the enhancement of aroma quality of
these products. Since a considerable amount of vanillin exists as its glycosidic precursor in cured
vanilla pods, a possible enhancement in yield of vanillin by radiation processing is thus expected.
Hence the highly stable oxygen–carbon linkage between vanillin and glucose limits the possible
enhancement of aroma quality of irradiated beans.
Colour is one of the most important traits in orchids and has created great interest in breeding programmes. Gamma irradiation is an alternative way for generation of somaclonal variation for new flower colours. Phenotypic changes are usually observed during screening and selection of mutants. Understanding of targeted gene expression level and evaluation of the changes facilitate in the development of functional markers for selection of desired flower colour mutants. Four Dendrobium orchid sequences (NCBI accessions: AM490639, AY41319, FM209429 and DQ462460) were selected to design gene specific primers based on information for chalcone synthase (CHS) from NCBI database. Quantitative real-time PCR (qPCR) was used to understand flower colour expression quantitatively derived from the CHS gene activities in different flower tissues (petal and sepal) from control Dendrobium Sonia (red purple), mutant DS 35-1/M (purple pink) and mutant DS 35-WhiteA. It was found that expression of CHS gene was highest in sepals of white flowers and lowest in both sepals and petals of purple pink flowers. Genomic DNA was amplified and PCR products were sequenced, aligned and compared. Sequence variations of CHS partial gene in Dendrobium Sonia mutants with different flower colour showed that two protein positions have been changed as compared to the control. These non-synonymous mutations may have contributed to the colour alterations in the white and purple pink mutants. This paper describes important procedures to quantify gene expression such as RNA isolation (quantity and quality), cDNA synthesis and primer design steps for CHS genes.
Mushroom can be used as a biological indicator in assessing radiological impact on the
environment. Radiological effect would be reflected through morphological changes as well as
those changes at molecular level. For this purpose, a preliminary work was conducted, which
included DNA isolation, optimization of PCR parameters for Inter-Simple Sequence Repeat (ISSR)
and primers screening on Pleurotus sajor caju mushroom strains from Nuclear Malaysia’s
Sterifeed Mushrooms Collection Centre. In this work, DNA isolation technique from cap and stalk
of fruit body were optimized and quantified. It was found that stalk produced highest amount of
genomic DNA at 304.01ng/µl and cap at 149.00ng/µl. A total of 100 ISSR primers were tested and
51 primers were successfully amplified. These primers will be used further for dose response
evaluation and molecular profiling in mushroom species.
Therapeutic application of metallic nanoparticles such as gold nanoparticles have been extensively investigated and intriguing finding have been reported. Superparamagnetic iron oxide nanoparticles (SPION) could also potentially have therapeutic properties that can be exploited to enhance radiotherapy outcome. In this study, investigations on the dose enhancement effects inflicted by SPIONs under irradiation with megavoltage photon beam radiotherapy were conducted. T24 human bladder cancer cell lines were pretreated with 1 mMol/L of SPION and irradiated with 6 MV and 10 MV photon beam at different doses.The non-treated cells irradiation was used as a control. Clonogenic assay was performed to determine the cell survival. Linear quadratic (LQ) model are used as fitting curve and does enhancement factors (DEF) were extrapolated from the curves. The cytotoxicity indicated cell growth normally after 72 hours and no long term cytotoxicity effects of SPIONs towards the cells were observed. The dose enhancement effects were observed for both 6 MV and 10 MV photon beam with DEF obtained 1.71 and 2.50, respectively. This reduction of cell colonies growth could be resulted from the interaction that induced free radical and reactive oxygen species (ROS) by megavoltage photon beams. The SPIONs were therefore act as multifunction nanoparticle both in diagnostic agent and radiotherapy as radiation dose enhancer, thus clearly qualified as future theranostic agents.
The study on the possibility of using DMU Kinematics module in CAE tools for dose exposure work planning was carried out. A case scenario was created using 3D CAD software and transferred to DMU Kinematics module in a CAE software. The work plan created using DMU Kinematics module was animated to simulate a real time scenario. Data on the phantom position against the radioactive source was collected by activating positioning sensors in the module. The data collected was used to calculate the estimated dose rate exposure for the phantom. The results can be used to plan the safest and optimum procedures in carrying out the radiation related task.
The exposure of food to ionizing radiation is being progressively used in many countries to
inactivate food pathogens, to eradicate pests and to extend shelf-life of food. To ensure free
consumer choice, irradiated food will be labeled. The availability of a reliable method to detect
irradiated food is important to enforce legal controls on labeling requirements, ensure proper
distribution and increase consumer confidence. This paper reports on the preliminary application
of photostimulated luminescence technique (PSL) as a potential method to detect irradiated food
and perhaps be used for monitoring irradiated food on sale locally in the near future. Thus this
study will be beneficial and relevant for application of food irradiation towards improving food
safety and security in Malaysia.
A 3.375 kJ plasma focus is designed to operate at 13.5 kV for studying X-ray source in Argon discharge. X-rays are detected by a film from the mammography radiographic plate using radiography technique. The feasibility of plasma focus as a high intensity flash X-ray radiation for a good contrast in radiography image is presented.
The acrylated palm oil (APO) nanoparticle is a potential product that can be used as carriers in
medical field. The main focus of the present study was to study the potential of the APO
nanoparticles for used in a controlled drug delivery system. The microemulsion system is used as a
medium to incorporate an active substance such as Thymoquinone (TQ) into the APO polymeric
micelle and then the radiation technique is used as a tool for the synthesis of TQ-loaded APO
nanoparticle. The nano-size TQ-loaded APO particles resulted the particle size of less than 150 nm
with spherical in shape. The TQ release profile was carried out in potassium buffer saline (PBS)
solutions (pH 7.4) at 37
oC. And, the zero-order model has been used to determine the mechanism
of the drug release from the corresponding nanoparticles, respectively. The TQ release was found
to be sustained and controlled in pH 7.4. At pH 7.4, the release of TQ followed the zero-order
model. The in-vitro drug release study showed a good prospect of the APO nanoparticle on being a
potential drug carrier as there are toxic against colon cancer cells and not toxic towards normal
cells. This suggested that the APO product produce using this radiation technique can be
developed into different type of carrier systems for controlled drug release applications.
Many times a year natural gas transmission and distribution companies need to make new connections to pipelines to expand or modify their existing system through hot tapping procedure. This procedure involves the installation of a new pipeline connection while the pipeline remains in service, flowing natural gas under pressure. The hot tap procedure includes attaching a branch connection and valve on the outside of an operating pipeline, and then cutting out the pipe-line wall within the branch and removing the wall section, which is called object of coupon through the valve. During the hot tapping process a critical problems occurred when a coupon fell into the mother pipeline. To overcome this problem, a gamma-ray absorption technique was chosen whereby a mapping technique will be done to detect the coupon position. The technique is non-destructive as it applies Co-60 (5mCi) as a radioisotope sealed source to emit gamma radiation and a NaI(Tl) scintillation as detector. The result provided a visible representation of density profile inside pipeline where the coupon location can be located. This paper provides the detail of the technique used and presents the result obtained.
Radiobiological model such as linear quadratic (LQ) is widely used in radiotherapy to predict the biophysical response of the tumour cell to the radiation. In clinical radiotherapy, LQ model is widely employed to plan treatment delivery and fractionation. Nevertheless, LQ model might not provide accurate prediction for high dose rate treatment. This study investigates the radiation cell survival responses using LQ model and alternative Multi-Target (MT) model. The experimental works were conducted in-vitro using HeLa cells that were irradiated using photon and electron beams of different energy. Cells irradiation were performed in full scatter condition and exposed to radiation doses ranges from 1 to 10 Gy. Clonogenic assay is used as an endpoint to obtain the cell survival curves which later be fitted with LQ and MT model. The results demonstrate that MT model produce the fitting curves that are closed to the experimental data compare to LQ model especially at high doses. Parameter analysis from both models indicates more biological damage inflicted by high energy electron beam. Correlation between the experimental cell survival data and radiobiological model analysis suggesting that alternative radiobiological model such as MT model could be applied in analysing cells’ radiation survival and damage in clinical radiotherapy.
The purpose of the study was to determine the effect of out-of-field photon beams radiotherapy to the cancer cell survival. In this study, HeLa and T24 cancer cells were irradiated with 6 MV and 10 MV photon beams in two different conditions, one with intercellular communication with the in-field cell and one without the communication. Cells survival was determined by clonogenic assay. In the presence of intercellular communication, the cell death was increased which indicate the presence of radiation induced bystander effects (RIBE). The effects were also dependent on the cell types and photon energy where the HeLa cells exhibit less survival compares to T24 cells and the effects were prominent at higher photon energy. This study demonstrates that the out-of-field cells in conjunction with RIBE plays important roles in the cells response towards megavoltage photon beam radiation therapy.
The ultimate check of the actual dose delivered to a patient in radiotherapy can be achieved by using dosimetric measurements. The aims of this study were to develop and evaluate a custom handmade head and neck phantom for evaluation of Three-Dimensional Conformal Radiation Therapy (3D-CRT) dose planning and delivery. A phantom of head and neck region of a medium built male patient with nasopharyngeal cancer was constructed from Perspex material. Primary and secondary Planning Target Volume (PTV) and twelve Organs at Risk (OAR) were delineated using Treatment Planning System (TPS) guided by computed tomography printout transverse images. One hundred and seven (107) holes distributed among the organs were loaded with Rod-shaped Thermoluminescent dosimeters (LiF:Mg,Ti TLDs) after common and individual calibration. Head and neck phantom was imaged, planned and irradiated conformally (3D-CRT) by linear accelerator (LINAC Siemens Artiste). The planned predicted doses by TPS at PTV and OAR regions were obtained and compared with the TLD measured doses using the phantom. Repeated TLD measurements were reproducible with a percent standard deviation of < 3.5%. Moreover, the average of dose discrepancies between TLDs reading and TPS predicted doses were found to be < 5.3%. The phantom’s preliminary results have proved to be a valuable tool for 3D-CRT treatment dose verification.
The particleboards were fabricated using Rhizophora spp. wood particles with particles size less than 74 μm. The corn starch was used as a bio-adhesive in the fabrication of Rhizophora spp. particleboards. The corn starch bonded particleboards were fabricated at 5% and 10% corn starch based on dry mass of Rhizophora spp. wood particles. The measurement of mass attenuation coefficients of the particleboards were made at low and intermediate photon energies. The mass attenuation coefficient at low photon energy was measured using X-ray fluorescent (XRF) configuration based on attenuation of Kα1 X-ray energies between 16.59 and 25.26 keV given by niobium, molybdenum, palladium and tin metal plates. The calculated mass attenuation coefficients of samples were compared to the theoretical values mass attenuation coefficients of water calculated using the photon cross-section database (XCOM). The results showed that mass attenuation coefficients of 10% corn starch added Rhizophora spp. particleboards were in good agreement of water within 7.96 and 4.94% for 5% and 10% corn starch Rhizophora spp. Particleboards, respectively compared to 14.57 and 16.16% in binderless Rhizophora spp. particleboards and raw Rhizophora spp. wood, respectively.
Gamma irradiation is widely used in sterilizationand mutagenesis,especially for plant breeding and crop protection. Microbial mutagenesisthrough gamma irradiation is mainly applied in fermentation industry. In agriculture, gamma irradiation is mostlyapplied in cropimprovement. Microbial mutagenesis is mainly applied against fungus and spore-forming bacteria,which are resistant to gamma irradiation.Response of microbes to gamma irradiation varies and depends on various factors. Reviewof previous works on gamma irradiation for microbial mutagenesis in agriculture may provide some information for the use of this method. Thegeneral view ongamma irradiation, its application,and mutagenesis are discussedin this paper. Further investigation onmicrobial mutagenesis should consider molecular changes,information on which is lacking in previous works.Moreover, studies on microbial mutagenesis are still lacking in Malaysiadespite having severalgamma irradiation facilities.Therefore, further studies on microbial mutagenesis should be conducted.
Effect of washing solutions’ pH on removal of radium-226 from radium-contaminated soil using distilled water and humic acid extracted from Malaysian peat soil was studied by a single batch washing method. The study encompassed the extraction of humic acid and the washing of radium-contaminated soil using distilled water and humic acid solutions of varying pH in the range between 3 to 11. Activity of radium-226 was determined by gamma spectrometer. In the pH range studied, the removal of radium-226 was greater when humic acid solutions were used compared to distilled water. Greater removal of radium-226 was obtained using highly basic pH washing solutions compared to neutral and acidic solutions.
A safety evaluation test on human for latex films made from Radiation Prevulcanized Natural Rubber Latex (RVNRL) with sulfur-containing antioxidant was studied. Sulfur test has confirmed that there was sulfur compound presence in RVNRL derived from antioxidant used in this study. Two types of safety evaluation test were being adopted which are Patch Test and Modified Draize-95 test and this test proved that there is no clinical evidence on the presence of sulfur compound in RVNRL that may induce Type IV allergy in the unsensitized general user population. Both clinical test shows that the highest score value produced by test subjects is 1 and not exceed the allowable limit.
On March 11, 2011, a serious accident occurred in Daiichi nuclear reactor plant, Fukushima,
Japan which caused radioactive materials been released into the atmosphere in the form of
aerosols and dust particles. Sea water around the plant was also found contaminated with high
radioactivity readings. These radioactive materials could be transported by the winds and ocean
current across international borders and cannot be controlled by human. Thus, a continuous
monitoring activity of radionuclide content in the air and sea water needs to be conducted by the
authorities. In addition to radioactivity monitoring, Malaysia should also control the entry of
contaminated food in order to prevent radionuclide ingestion by human. The radionuclide 131I,
134Cs and 137Cs were used as a measure of pollution levels and counted with gamma spectrometry
using standard analysis method suggested by AOAC International. In this paper, details description
of the role of Radiochemical and Environment Group, Nuclear Malaysia who’s responsible in
analyzing the radioactivity in the food samples due to Fukushima Daiichi, Japan accident was
included. The radioactivity limit adopted and analysis results from this monitoring were discussed
Nur Humaira’ Lau Abdullah, Zal U’yun Wan Mahmood, Norfaizal Mohamed @ Muhamad, Nazaratul Ashifa Abdullah Salim, Ahmad Nazrul Abd Wahid, Nor Dalila Desa, et al.
A glasshouse experiment was performed to evaluate the uptake of grasses viz. Napier and Vetiver
in radiophytoremediation of caesium-contaminated soil. The radiophytoremediation experiment
was designed according to the Randomized Complete Block Design (RCBD). The grasses were
grown in troughs filled with soil mixed with a known specific activity of 134Cs. Initial Cs activity and
activity after different cultivation time intervals of 1, 3, 6 and 9 months were analyzed using gamma
spectrometer direct measurement. The results showed the uptake of caesium by Napier and Vetiver
after 9 months with the transfer factors (TF) were 4.70 and 6.25, respectively. The remediation of
caesium from the contaminated soil during the study period was 98.08% for Napier and 98.21% for
Vetiver. Both grasses have been found to accumulate caesium, with Vetiver accumulating higher
than Napier. Thus, the present study suggests that Vetiver could be used as a potential plant for
radiophytoremediation of caesium.
Paper recycling plants usually buy their raw material from suppliers. More than often, bulk used paper supplied to the plant contains some significant quantity of water in its internal voids. It may be included intentionally or unintentionally. The price of used paper depends on its weight, thus adding water will help to increase weight and consequently increase the price. In this way, plant owner who purchase the used paper suffers a significant of financial lost. The objectives of our experiment are to establish a calibration curve that correlate between the amount of neutron backscattered and water content, and finally to develop a correction factor that need to be introduced to the measured values of water content. A fast neutron source (Am-Be 241) and a portable backscattering neutron detector were used for water measurement. The experiments were carried out by measuring neutron backscattering from used paper that has been added with different amount of water. As a result, a neutron calibration curve that provides a correlation between neutron backscattering and water content was established.