This prospective study aimed to determine the extent of contamination of fentanyl solutions used for central neuraxial injection by wiping the neck of the ampoules with 70% isopropyl alcohol swabs (Kendall) before breaking open the ampoules and aspiration of fentanyl solutions using a 5 microm Filter Straw (B. Braun). In Group A, fifty fentanyl ampoules were wiped with 70% isopropyl alcohol swab prior to opening and the contents were aspirated immediately using a 21G needle and a 5 microm filter straw for culture. The same steps were repeated on the remaining solutions after two hours. In Group B, all the above steps were repeated but without wiping the ampoules with 70% isopropyl alcohol swabs. None of the samples from the wiped ampoules or aspiration using filter straw grew microorganisms. Six percent of the samples from unwiped group grew microorganisms when fentanyl were aspirated using a 21G needle and the contamination increased to 16% when repeated after two hours. Wiping the outsides of the fentanyl ampoules with 70% isopropyl alcohol swabs before opening or aspirating the contents using a 5 pm filter straw has been shown to be equally effective in avoiding bacterial contamination and should be practiced routinely when performing regional anaesthesia.
KEY WORDS: Fentanyl solution, Isopropyl alcohol swab, Filter straw, Contamination, Regional anaesthesia, Hospital Kuala Lumpur, Malaysia
PMMA polymer microfiber doped Multi Walled Carbon Nanotubes (MWCNTs) was reported for alcohol sensing application. The sensitivity of the sensor is increasing relatively with the increment of the alcohol concentration which affects the transmission output power. However, the challenges are on choosing the right material and the simplicity on the fabrication of microfiber sensor for an improvement of the sensitivity of the sensor. A PMMA polymer microfiber doped MWCNTs was introduced for an application of alcohol detection system. Direct drawing technique was used to form a uniform waist size of microfiber sensor with 6µm diameter and 5mm length respectively. The performance of the fabricated sensor was tested with two types of alcohol, namely ethanol and 2-propanol at concentrations varying from 2% to 8% with 2% intervals. The performance which includes sensitivity, linearity and resolution were studied and analysed for the undoped PMMA and PMMA doped MWCNTs-doped polymer microfiber. The PMMA doped MWCNTs sensor which exhibited higher sensitivity for ethanol sensing with 83.23dBm/% with a linearity of 99.96% and a sensitivity of 73.75dBm/% with linearity 99.82% for 2- propanol sensing. The resolution has improved significantly by 0.0004% and 0.0007% respectively. In conclusion, PMMA doped MWCNTs was able to increase the sensitivity as well as the reproducibility of the microfiber sensor for the alcohol detection system.
In this paper, a facile synthesis method for CaFe2O4 is introduced that produces a catalyst capable of significant photocatalytic degradation of POME under visible light irradiation. The co-precipitation method was used to produce two catalysts at calcination temperatures of 550 °C and 700 °C dubbed CP550 and CP700. CP550 demonstrated the maximum COD removal of 69.0% at 0.75 g/L catalyst loading after 8 h of visible light irradiation which dropped to 61.0% after three consecutive cycles. SEM images indicated that the higher calcination temperature of CP700 led to annealing which reduced the pore volume (0.025 cm3/g) and pore diameter (10.3 nm) while simultaneously creating a smoother and more spherical surface with lower SBET (9.73 m2/g). In comparison, CP550 had a rough hair-like surface with higher SBET (27.28 m2/g) and pore volume (0.077 cm3/g) as evidenced by BET analysis. XRD data indicated the presence of CaFe5O7 in the CP550 composition which was not present in CP700. The presence of Wustite-like FeO structures in CaFe5O7 are likely the cause for lower photoluminescence intensity profile and hence better charge separation of CP550 as these structures in CaFe2O4 have been known to increase resistivity and electron localization. The COD removal of CP550 dropped from 69.0% to just 7.0% upon adding a small quantity of isopropanol into the reaction mixture indicating hydroxyl radicals as the primary reactive oxidative species.
Platinum nanoparticles were synthesized using the gamma radiolytic technique in an aqueous solution containing Platinum tetraammine chloride in presence of poly vinyl pyrrolidone, isopropanol, tetrahydrofuran and deionized water. The gamma irradiation was carried out in a60Co gamma source chamber and the particle size was found to decrease from 4.88 to 3.14 nm on increasing the gamma radiation dose from 80 to 120 kGy. UV-visible absorption spectra were measured and revealed two steady absorption maxima at 216 and 264 nm in the UV region, which was blue shifted (i.e. toward lower wavelength) with decreasing particle size. By taking the conduction electrons of an isolated particle that are not entirely free, but instead bound to their respective quantum levels, the optical absorption of platinum nanoparticles can be calculated via intra-band quantum excitation for particle sizes similar to those measured experimentally. We found that the calculated absorption maxima of electronic excitations matched the measured absorption maxima well. This finding suggests that the optical absorption of metal nanoparticles commonly applied in nanoscience and nanotechnology can be described accurately by the quantum excitation of conduction electrons.